Ruostumattoman teräksen käyttö ja käyttövaatimukset LNG:n varasto- ja kuljetusjärjestelmissä

On arvioitu, että koko maailmaa kattava energiantarve nousee 1,2 % vuosinopeudella. Asiaa ei kaunista se tosiasia, että valtaosa tänä päivänä tuotetusta energiasta (85 %) on lähtöisin fossiilisista polttoaineista. Päästöjen on arvioitu lisääntyvän 2005 – 2030 välisenä aikana noin 30 %, vaikka uusiutuvaa energiaa käytettäisiin ja prosessien hyötysuhteet paranisivat. Vuonna 2015 voimaan tuleva rikkidirektiivi on pakottanut asiantuntijat löytämään korvaavan energialähteen, joka vähentäisi päästöjen määrää, ja jota esiintyisi suurissa määrissä. Nesteytetty maakaasu, LNG, toteuttaa edellä mainitut ehdot. Tässä diplomityössä perehdytään LNG-teollisuuden arvoketjuun Suomessa sekä muualla maailmassa. Työssä pääpainona on selvittää ruostumattoman teräksen käyttömahdollisuuksia nykyisessä LNG-teollisuuden arvoketjussa sekä selvittää sen uusia sovelluskohteita LNG-alalla tulevaisuudessa. Diplomityössä on tehty laaja kirjallisuuskatsaus LNG:n arvoketjuun ja uuden EN 1.4420 ruostumattoman teräksen soveltuvuuteen kryogeenisissä lämpötiloissa. Työn aikana on myös tehty useita haastatteluja LNG-teollisuudessa toimivien henkilöiden kanssa. Menetelmäkokeita ja koehitsauksia on suoritettu näiden haastattelujen perusteella.

Use of grass carp (Ctenopharyngodon idella) as a biological control agent for submerged aquatic macrophytes

This study aimed to evaluate feed preference and control efficacy of grass carp (Ctenopharyngodon idella) on the aquatic macrophytes Ceratophyllum demersum, Egeria densa and Egeria najas. An experiment was carried out at mesocosms conditions with 2,000 liters capacity and water residence time of 2.8 days. C. demersum, E. densa e E. najas biomasses were offered individually with sixty g and coupled in similar quantities of 30 g of each species, evaluated during 81 days, envolving 6 treatments. (1 - C. demersum, 2 - E. najas, 3 -E. densa, 4 - C. demersum + E. najas, 5 - C. demersum + E. densa and 6 - E. najas + E. densa). When offered individually, E. najas and C. demersum presented the same predation rate by grass carp, which was higher than E. densa predation rate. When plants were tested in pairs, the order of feed preference was C. demersum > E. najas > E. densa. E. najas and C. demersum percentage control ranged from 73 to 83%. No relation between biomass consumption and grass carp body weight gain was observed, probably due to differences in nutritional quality among macrophyte species according to fish necessities. Therefore, it is concluded that the use of grass carp is one excellent technique to control submersed macrophytes in Brazil.

Methyl and ethyl chloride synthesis in microreactors

Methyl chloride is an important chemical intermediate with a variety of applications. It is produced today in large units and shipped to the endusers. Most of the derived products are harmless, as silicones, butyl rubber and methyl cellulose. However, methyl chloride is highly toxic and flammable. On-site production in the required quantities is desirable to reduce the risks involved in transportation and storage. Ethyl chloride is a smaller-scale chemical intermediate that is mainly used in the production of cellulose derivatives. Thus, the combination of onsite production of methyl and ethyl chloride is attractive for the cellulose processing industry, e.g. current and future biorefineries. Both alkyl chlorides can be produced by hydrochlorination of the corresponding alcohol, ethanol or methanol. Microreactors are attractive for the on-site production as the reactions are very fast and involve toxic chemicals. In microreactors, the diffusion limitations can be suppressed and the process safety can be improved. The modular setup of microreactors is flexible to adjust the production capacity as needed. Although methyl and ethyl chloride are important chemical intermediates, the literature available on potential catalysts and reaction kinetics is limited. Thus the thesis includes an extensive catalyst screening and characterization, along with kinetic studies and engineering the hydrochlorination process in microreactors. A range of zeolite and alumina based catalysts, neat and impregnated with ZnCl2, were screened for the methanol hydrochlorination. The influence of zinc loading, support, zinc precursor and pH was investigated. The catalysts were characterized with FTIR, TEM, XPS, nitrogen physisorption, XRD and EDX to identify the relationship between the catalyst characteristics and the activity and selectivity in the methyl chloride synthesis. The acidic properties of the catalyst were strongly influenced upon the ZnCl2 modification. In both cases, alumina and zeolite supports, zinc reacted to a certain amount with specific surface sites, which resulted in a decrease of strong and medium Brønsted and Lewis acid sites and the formation of zinc-based weak Lewis acid sites. The latter are highly active and selective in methanol hydrochlorination. Along with the molecular zinc sites, bulk zinc species are present on the support material. Zinc modified zeolite catalysts exhibited the highest activity also at low temperatures (ca 200 °C), however, showing deactivation with time-onstream. Zn/H-ZSM-5 zeolite catalysts had a higher stability than ZnCl2 modified H-Beta and they could be regenerated by burning the coke in air at 400 °C. Neat alumina and zinc modified alumina catalysts were active and selective at 300 °C and higher temperatures. However, zeolite catalysts can be suitable for methyl chloride synthesis at lower temperatures, i.e. 200 °C. Neat γ-alumina was found to be the most stable catalyst when coated in a microreactor channel and it was thus used as the catalyst for systematic kinetic studies in the microreactor. A binder-free and reproducible catalyst coating technique was developed. The uniformity, thickness and stability of the coatings were extensively characterized by SEM, confocal microscopy and EDX analysis. A stable coating could be obtained by thermally pretreating the microreactor platelets and ball milling the alumina to obtain a small particle size. Slurry aging and slow drying improved the coating uniformity. Methyl chloride synthesis from methanol and hydrochloric acid was performed in an alumina-coated microreactor. Conversions from 4% to 83% were achieved in the investigated temperature range of 280-340 °C. This demonstrated that the reaction is fast enough to be successfully performed in a microreactor system. The performance of the microreactor was compared with a tubular fixed bed reactor. The results obtained with both reactors were comparable, but the microreactor allows a rapid catalytic screening with low consumption of chemicals. As a complete conversion of methanol could not be reached in a single microreactor, a second microreactor was coupled in series. A maximum conversion of 97.6 % and a selectivity of 98.8 % were reached at 340°C, which is close to the calculated values at a thermodynamic equilibrium. A kinetic model based on kinetic experiments and thermodynamic calculations was developed. The model was based on a Langmuir Hinshelwood-type mechanism and a plug flow model for the microreactor. The influence of the reactant adsorption on the catalyst surface was investigated by performing transient experiments and comparing different kinetic models. The obtained activation energy for methyl chloride was ca. two fold higher than the previously published, indicating diffusion limitations in the previous studies. A detailed modeling of the diffusion in the porous catalyst layer revealed that severe diffusion limitations occur starting from catalyst coating thicknesses of 50 μm. At a catalyst coating thickness of ca 15 μm as in the microreactor, the conditions of intrinsic kinetics prevail. Ethanol hydrochlorination was performed successfully in the microreactor system. The reaction temperature was 240-340°C. An almost complete conversion of ethanol was achieved at 340°C. The product distribution was broader than for methanol hydrochlorination. Ethylene, diethyl ether and acetaldehyde were detected as by-products, ethylene being the most dominant by-product. A kinetic model including a thorough thermodynamic analysis was developed and the influence of adsorbed HCl on the reaction rate of ethanol dehydration reactions was demonstrated. The separation of methyl chloride using condensers was investigated. The proposed microreactor-condenser concept enables the production of methyl chloride with a high purity of 99%.

Utilization of steelmaking waste materials for production of calcium carbonate (CaCO3)

The steel industry produces, besides steel, also solid mineral by-products or slags, while it emits large quantities of carbon dioxide (CO2). Slags consist of various silicates and oxides which are formed in chemical reactions between the iron ore and the fluxing agents during the high temperature processing at the steel plant. Currently, these materials are recycled in the ironmaking processes, used as aggregates in construction, or landfilled as waste. The utilization rate of the steel slags can be increased by selectively extracting components from the mineral matrix. As an example, aqueous solutions of ammonium salts such as ammonium acetate, chloride and nitrate extract calcium quite selectively already at ambient temperature and pressure conditions. After the residual solids have been separated from the solution, calcium carbonate can be precipitated by feeding a CO2 flow through the solution. Precipitated calcium carbonate (PCC) is used in different applications as a filler material. Its largest consumer is the papermaking industry, which utilizes PCC because it enhances the optical properties of paper at a relatively low cost. Traditionally, PCC is manufactured from limestone, which is first calcined to calcium oxide, then slaked with water to calcium hydroxide and finally carbonated to PCC. This process emits large amounts of CO2, mainly because of the energy-intensive calcination step. This thesis presents research work on the scale-up of the above-mentioned ammonium salt based calcium extraction and carbonation method, named Slag2PCC. Extending the scope of the earlier studies, it is now shown that the parameters which mainly affect the calcium utilization efficiency are the solid-to-liquid ratio of steel slag and the ammonium salt solvent solution during extraction, the mean diameter of the slag particles, and the slag composition, especially the fractions of total calcium, silicon, vanadium and iron as well as the fraction of free calcium oxide. Regarding extraction kinetics, slag particle size, solid-to-liquid ratio and molar concentration of the solvent solution have the largest effect on the reaction rate. Solvent solution concentrations above 1 mol/L NH4Cl cause leaching of other elements besides calcium. Some of these such as iron and manganese result in solution coloring, which can be disadvantageous for the quality of the PCC product. Based on chemical composition analysis of the produced PCC samples, however, the product quality is mainly similar as in commercial products. Increasing the novelty of the work, other important parameters related to assessment of the PCC quality, such as particle size distribution and crystal morphology are studied as well. As in traditional PCC precipitation process, the ratio of calcium and carbonate ions controls the particle shape; a higher value for [Ca2+]/[CO32-] prefers precipitation of calcite polymorph, while vaterite forms when carbon species are present in excess. The third main polymorph, aragonite, is only formed at elevated temperatures, above 40-50 °C. In general, longer precipitation times cause transformation of vaterite to calcite or aragonite, but also result in particle agglomeration. The chemical equilibrium of ammonium and calcium ions and dissolved ammonia controlling the solution pH affects the particle sizes, too. Initial pH of 12-13 during the carbonation favors nonagglomerated particles with a diameter of 1 μm and smaller, while pH values of 9-10 generate more agglomerates of 10-20 μm. As a part of the research work, these findings are implemented in demonstrationscale experimental process setups. For the first time, the Slag2PCC technology is tested in scale of ~70 liters instead of laboratory scale only. Additionally, design of a setup of several hundreds of liters is discussed. For these purposes various process units such as inclined settlers and filters for solids separation, pumps and stirrers for material transfer and mixing as well as gas feeding equipment are dimensioned and developed. Overall emissions reduction of the current industrial processes and good product quality as the main targets, based on the performed partial life cycle assessment (LCA), it is most beneficial to utilize low concentration ammonium salt solutions for the Slag2PCC process. In this manner the post-treatment of the products does not require extensive use of washing and drying equipment, otherwise increasing the CO2 emissions of the process. The low solvent concentration Slag2PCC process causes negative CO2 emissions; thus, it can be seen as a carbon capture and utilization (CCU) method, which actually reduces the anthropogenic CO2 emissions compared to the alternative of not using the technology. Even if the amount of steel slag is too small for any substantial mitigation of global warming, the process can have both financial and environmental significance for individual steel manufacturers as a means to reduce the amounts of emitted CO2 and landfilled steel slag. Alternatively, it is possible to introduce the carbon dioxide directly into the mixture of steel slag and ammonium salt solution. The process would generate a 60-75% pure calcium carbonate mixture, the remaining 25-40% consisting of the residual steel slag. This calcium-rich material could be re-used in ironmaking as a fluxing agent instead of natural limestone. Even though this process option would require less process equipment compared to the Slag2PCC process, it still needs further studies regarding the practical usefulness of the products. Nevertheless, compared to several other CO2 emission reduction methods studied around the world, the within this thesis developed and studied processes have the advantage of existing markets for the produced materials, thus giving also a financial incentive for applying the technology in practice.

Superoxide: a two-edged sword

Superoxide (O2-) is the compound obtained when oxygen is reduced by one electron. For a molecule with an unpaired electron, O2- is surprisingly inert, its chief reaction being a dismutation in which it reacts with itself to form H2O2 and oxygen. The involvement of O2- in biological systems was first revealed by the discovery in 1969 of superoxide dismutase, an enzyme that catalyzes the dismutation of O2-. Since then it has been found that biological systems produce a bewildering variety of reactive oxidants, all but a few arising ultimately from O2-. These oxidants include O2- itself, H2O2 and alkyl peroxides, hydroxyl radical and other reactive oxidizing radicals, oxidized halogens and halamines, singlet oxygen, and peroxynitrite. These various oxidants are able to damage molecules in their environment, and are therefore very dangerous. They are thought to participate in the pathogenesis of a number of common diseases, including among others malignancy, by their ability to mutate the genome, and atherosclerosis, by their capacity for oxidizing lipoproteins. Their properties are put to good use, however, in host defense, where they serve as microbicidal and parasiticidal agents, and in biological signalling, where their liberation in small quantities results in redox-mediated changes in the functions of enzymes and other proteins

Minimizing Conducted RF-Emissions in Switch Mode Power Supplies Using Spread-Spectrum Techniques

Switching power supplies are usually implemented with a control circuitry that uses constant clock frequency turning the power semiconductor switches on and off. A drawback of this customary operating principle is that the switching frequency and harmonic frequencies are present in both the conducted and radiated EMI spectrum of the power converter. Various variable-frequency techniques have been introduced during the last decade to overcome the EMC problem. The main objective of this study was to compare the EMI and steady-state performance of a switch mode power supply with different spread-spectrum/variable-frequency methods. Another goal was to find out suitable tools for the variable-frequency EMI analysis. This thesis can be divided into three main parts: Firstly, some aspects of spectral estimation and measurement are presented. Secondly, selected spread spectrum generation techniques are presented with simulations and background information. Finally, simulations and prototype measurements from the EMC and the steady-state performance are carried out in the last part of this work. Combination of the autocorrelation function, the Welch spectrum estimate and the spectrogram were used as a substitute for ordinary Fourier methods in the EMC analysis. It was also shown that the switching function can be used in preliminary EMC analysis of a SMPS and the spectrum and autocorrelation sequence of a switching function correlates with the final EMI spectrum. This work is based on numerous simulations and measurements made with the prototype. All these simulations and measurements are made with the boost DC/DC converter. Four different variable-frequency modulation techniques in six different configurations were analyzed and the EMI performance was compared to the constant frequency operation. Output voltage and input current waveforms were also analyzed in time domain to see the effect of the spread spectrum operation on these quantities. According to the results presented in this work, spread spectrum modulation can be utilized in power converter for EMI mitigation. The results from steady-state voltage measurements show, that the variable-frequency operation of the SMPS has effect on the voltage ripple, but the ripple measured from the prototype is still acceptable in some applications. Both current and voltage ripple can be controlled with proper main circuit and controller design.

Metsäteollisuuden puunhankinnan ohjaus: Hankintalähteen kannattavuus ja siihen vaikuttavat tekijät

Tutkielmassa rakennettiin laskentamalli metsäteollisuuden puunhankinnan hankintalähteen kannattavuuden määrittämiseksi ja selittämiseksi. Tutkimuksessa noudatettiin konstruktiivisen tapaustutkimuksen tutkimusotetta. Tutkimuksen kohdeorganisaationa oli kansainvälisesti toimivan metsäteollisuusyrityksen Suomen puunhankintaorganisaatio. Kannattavuusmalli määrittelee hankintalähteen kannattavuuden sekä käsitteellisellä että laskentamenettelyn tasolla. Kannattavuusmallin katesuure on porttikate, joka rakennettiin taloudellisen lisäarvon teoriaan nojaten kohdeorganisaation tarpeiden ja sen laskenta-asiantuntijoiden näkemysten perusteella. Kannattavuusmallin rakenne ja osat kuvattiin seikkaperäisesti. Kannattavuusmallin käyttämän liiketoimintadatan poiminta ja laskentasuureiden raportointi testattiin. Mallin tarvitsemat laskentatiedot on saatavissa kohdeorganisaation kehitteillä olevasta toiminnanohjausjärjestelmästä. Laskentamallin hyödyntämismahdollisuudet arvioitiin. Hankintalähteen kannattavuutta mittaavalla porttikatteella voidaan ohjata puunhankintaorganisaatiota sen tavoitteiden saavuttamisessa. Malli ilmaisee porttikatteeseen vaikuttavien tekijöiden vaikutuksen kannattavuuteen, minkä avulla voidaan tehdä parempia päätöksiä hankintalähteiden hyödyntämisessä. Aiemmista tutkimuksista poiketen malli huomioi hankintalähteen suoritteen arvon tärkeimmille asiakastehtaille perustuen todellisiin liiketapahtumiin. Kannattavuusmallia voidaan hyödyntää laajalti metsäteollisuusyritysten tavaralajimenetelmään perustuvassa puunhankinnassa. Kannattavuusmallin rakentaminen rohkaisee puunhankinnan johtoa ja laskentahenkilöitä hedelmällisen yhteistyöhön.

Prosessilaitteen teräsrakenteen optimointi

Diplomityön tarkoituksena oli optimoida puukentän nosturin teräsrakenteiden kustannuksia ja selvittää halvemman valmistusmaan vaikutus nosturin kokonaiskustannukseen. Tavoitteena oli saada 15 % kokonaiskustannussäästö. Työn alussa perehdytään optimoitavan nosturin rakenteeseen ja mahdollisiin rakenteen optimoitaviin osiin. Teräsrakenteen optimointi alkoi kustannusrakenteen tarkalla selvittämisellä. Näin saatiin kuva nosturin kokonaiskustannuksesta ja mahdollisista säästökohteista. Uusien ideoiden kehittämisessä käytettiin hyväksi osatoimintojen pisteytystä ja ideamatriisia. Ideamatriisin lopputuloksena uudet rakenteet tarkastettiin nosturin kuormituksien suhteen ja valittiin kustannusten kannalta paras ratkaisu. Teräsrakenteeseen tehtiin muutoksia myös merirahdin konttien asettamien rajaehtojen mukaan. Kiinassa valmistettavalle teräsrakenteelle tehtiin rahtisuunnitelma, jossa selvitettiin optimaalinen rahtimuoto ja tarvittavien konttien lukumäärä. Tarjouskilpailun avulla saatiin halvin kuljetushinta valmistavalta tehtaalta työmaalle. Lopuksi nosturin optimoidun teräsrakenteen kustannuksia verrattiin työn alussa selvitettyyn kustannusrakenteeseen. Työn lopputuloksena päästiin 12 % potentiaaliseen kustannussäästöön, joka jäi kolme prosenttiyksikköä kustannussäästötavoitteesta.

3D-tulostustekniikan hyödyntäminen diagnostisten pikatestien tuotekehityksessä

Pikamallinnustekniikat ovat kehittyneet viime vuosina nopeasti. Tämä antaa jo lähes rajat-tomat mahdollisuudet tuottaa 3D-tulostamalla erilaisia tuotteita. 3D-tulostuksen hyödyntä-minen on yleistynyt erityisesti teollisuuden ja teknologian aloilla. Tässä työssä tutkittiin miten 3D-tulostamista voidaan hyödyntää diagnostisten pikatestien tuotekehityksessä. Immunologinen lateral flow-testi on vasta-aineisiin perustuva, nopea ja helppokäyttöinen mittausmenetelmä pienten ainemäärien havaitsemiseen. Tässä työssä kehitettiin lateral flow-testikotelo, jonka suunnitteluun ja rakenteen mallintamiseen käytettiin 3D-tulostustekniikkaa. Testikotelon toimivuus lateral flow- testissä varmistettiin kehittämällä testikoteloon sopiva pikatesti, jonka suorituskykyä analysoitiin sekä visuaalisesti että Actim 1ngeni-lukulaitteella. Työ aloitettiin tutkimalla eri pikavalmistustekniikoita, joista testikotelon tulostamiseen valittiin SLA-tekniikka sen tulostustarkkuuden ja tuotteen pinnan laadun perusteella. Testikotelon suunnittelu aloitettiin määrittämällä millaisia ominaisuuksia testikotelolta haluttiin. Näitä ominaisuuksia olivat lateral flow-testin suojaaminen sekä testissä kulkevan näytteen virtauksen varmistamien. Lateral flow- testin kehityksessä hyödynnettiin osin aiemmin kehitetystä pikatestistä saatuja tietoja. Lateral flow- kasettitestin valmistusprosessi koostui seitsemästä eri prosessivaiheesta jotka olivat: Vasta-aineen/kontrollireagenssin konjugointi, näytetyynyn käsittely, konjugointityynyn käsittely, konjugointityynylle annostelu, membraanille annostelu, tikkujen laminointi ja leikkaus sekä kasettitestin kokoonpano. Kehitetyn lateral flow- kasettitestin toimivuus varmistettiin tutkimalla testin reaktiokinetiikkaa ja analyyttistä herkkyyttä sekä visuaalisesti että lukulaitteen avulla. Tutkimustulosten perusteella 3D-tulostus on erittäin hyödyllinen menetelmä pikatestien tuotekehityksessä suunniteltaessa testikotelorakenteita, näytteen annosteluvälineitä ja näiden yhdistelmiä.

Wood biochemicals for the protection of health. Focus on hemicellulose, stilbenoids and lignans

Trees produce an enormous amount of compounds that are still scantly utilized.However, the results obtained from structurally similar biochemicals suggest that wood-derived compounds could be used for the protection of health in various applications. Polyphenols, for instance, could be extracted from wood in high quantities. Similar polyphenols to those in wood include resveratrol, found in grapes, and secoisolariciresinol, present in flaxseeds. Their consumption has been inversely associated with the incidence of various diseases, especially certain cancers and obesity-related disorders. The aim of this study was to determine the health-promoting effects of woodderived biochemicals. The effect of spruce hemicellulose on the growth of probiotic intestinal bacteria was studied. The results suggest that the bifidobacteria and lactobacilli can utilize hemicellulose and thus it has potential as a prebiotic compound. In particular, the efficacy of pine polyphenols to inhibit the growth of prostate cancer was our main interest. It was found that stilbenoids and lignans inhibited the proliferation of various cancer cells, and reduced the growth of prostate cancer xenografts in mice. The polyphenol rich pine knot extract was well tolerated in diet and extract-derived polyphenols were rapidly absorbed after intake. Furthermore, we determined the effect of the dietary pine knot extract on the weight gain and the expression of aromatase gene in reporter mouse expressing the promoter region of a human aromatase gene. It was found that dietary pine knot extract alleviated the obesity-induced inflammation in adipose tissue and downregulated the expression of a human aromatase gene. Taken together, several components of spruce and pine may have a future role as health-promoting compounds.

Litiumin erotus väkevistä kloridiliuoksista ioninvaihdolla

Litiumioniakkujen kehityksen myötä litiumin tarve ja kysyntä ovat kasvaneet viime vuodet tasaisesti noin 10 % vuosivauhdilla. Kasvun on myös ennustettu jatkuvan samanlaisena tulevaisuudessa, jonka takia erilaiset litiumin erotusprosessit ovat nousseet tutkimuksen kohteeksi. Tärkeimmät litiumlähteet sijaitsevat suola-aavikoilla ja -järvillä, joihin litiumia on kerääntynyt suuria määriä maanpinnan läheisyyteen. Litiumia erotetaan suolatasangoilla aikaa vievissä haihdutus- ja saostusvaiheissa. Suolaliuokset sisältävät litiumin lisäksi muita metalleja, kuten magnesiumia, kalsiumia ja natriumia, joista etenkin magnesium häiritsee litiumin erotusta. Aikaisemmissa tutkimuksissa ei ole löydetty litiumille riittävän selektiivistä ioninvaihtohartsia. Tehdyissä tutkimuksissa muut metallit on usein erotettu selektiivisesti ennen litiumia ja litium on erotettu lopuksi. Litiumin erotusta voitaisiin parantaa, mikäli se onnistuisi selektiivisesti suoraan suolaliuoksesta. Tässä työssä tutkittiin litiumin selektiivistä erotusta magnesium- ja kalsiumpitoisesta väkevästä kloridiliuoksesta ioninvaihtohartseilla sekä molekyyliseulalla. Käytetyt neljä ioninvaihtohartsia olivat kaupallisia Puroliten hartseja: MN200, S940, CT151 ja A170. Molekyyliseula oli Sigman huokoskoon 4 Å zeoliittia. Kromatografisilla kolonnikokeilla saadut näytteet analysoitiin ICP-AES:lla. Tulosten perusteella ei yksikään tutkituista hartseista ja molekyyliseulasta ollut selektiivinen litiumille.

Suljetun jätetäytön kaatopaikkavesien käsittelyvaihtoehtojen vertailu

Hajoaminen kaatopaikalla tapahtuu fysikaalisten, kemiallisten ja biologisten prosessien avulla. Nämä prosessit voivat kestää vuosista jopa vuosikymmeniin. Näiden prosessien kehittymistä ajan saatossa kuvataan jätetäytön eri hajoamisvaiheiden avulla. Kaatopaikan eri toiminnoista syntyvät vesivirrat ovat laadultaan ja määrältään hyvin erilaisia. Suotovesi syntyy jätetäytön läpi suotautuvasta vedestä ja on yleisesti ottaen suurin kaatopaikkavesien kuormituksen aiheuttaja. Suotoveden sisältämien pitoisuuksien tiedetään laskevan kun jätteen loppusijoitus on lopetettu ja kun jätetäyttö on suljettu pintarakentein. Mitä pidemmälle jätetäytön hajoaminen on edennyt, sitä pienemmät suotoveden pitoisuudet ovat. Hyvä käytäntö on erottaa erityyppiset kaatopaikkavedet toisistaan ja käsitellä ne niiden vaatimalla tavalla. Diplomityön tarkoitus on löytää ympäristöystävällisin ja taloudellisin keino suljetun jätetäytön suotovesien sekä muiden vähintään yhtä laimeiden kaatopaikkavesien käsittelemiseksi. Vertailtavia käsittelymenetelmiä ovat kunnallisella jätevedenpuhdistamolla ja juurakkopuhdistamolla käsittely. Työn tulos on, että eri tyyppisillä juurakkopuhdistamoilla voidaan tehokkaasti käsitellä kaatopaikkavesiä. Empiirisen osan tarkastelu osoittaa, että hyvin pienien haitta-aine- ja ravinnepitoisuuksien käsittelyssä juurakkopuhdistamo on ympäristöystävällisempi sekä taloudellisempi kunnalliseen jätevedenpuhdistamoon verrattuna.

Fuzzy real option analysis in patent related decision making and patent valuation

The shift towards a knowledge-based economy has inevitably prompted the evolution of patent exploitation. Nowadays, patent is more than just a prevention tool for a company to block its competitors from developing rival technologies, but lies at the very heart of its strategy for value creation and is therefore strategically exploited for economic pro t and competitive advantage. Along with the evolution of patent exploitation, the demand for reliable and systematic patent valuation has also reached an unprecedented level. However, most of the quantitative approaches in use to assess patent could arguably fall into four categories and they are based solely on the conventional discounted cash flow analysis, whose usability and reliability in the context of patent valuation are greatly limited by five practical issues: the market illiquidity, the poor data availability, discriminatory cash-flow estimations, and its incapability to account for changing risk and managerial flexibility. This dissertation attempts to overcome these impeding barriers by rationalizing the use of two techniques, namely fuzzy set theory (aiming at the first three issues) and real option analysis (aiming at the last two). It commences with an investigation into the nature of the uncertainties inherent in patent cash flow estimation and claims that two levels of uncertainties must be properly accounted for. Further investigation reveals that both levels of uncertainties fall under the categorization of subjective uncertainty, which differs from objective uncertainty originating from inherent randomness in that uncertainties labelled as subjective are highly related to the behavioural aspects of decision making and are usually witnessed whenever human judgement, evaluation or reasoning is crucial to the system under consideration and there exists a lack of complete knowledge on its variables. Having clarified their nature, the application of fuzzy set theory in modelling patent-related uncertain quantities is effortlessly justified. The application of real option analysis to patent valuation is prompted by the fact that both patent application process and the subsequent patent exploitation (or commercialization) are subject to a wide range of decisions at multiple successive stages. In other words, both patent applicants and patentees are faced with a large variety of courses of action as to how their patent applications and granted patents can be managed. Since they have the right to run their projects actively, this flexibility has value and thus must be properly accounted for. Accordingly, an explicit identification of the types of managerial flexibility inherent in patent-related decision making problems and in patent valuation, and a discussion on how they could be interpreted in terms of real options are provided in this dissertation. Additionally, the use of the proposed techniques in practical applications is demonstrated by three fuzzy real option analysis based models. In particular, the pay-of method and the extended fuzzy Black-Scholes model are employed to investigate the profitability of a patent application project for a new process for the preparation of a gypsum-fibre composite and to justify the subsequent patent commercialization decision, respectively; a fuzzy binomial model is designed to reveal the economic potential of a patent licensing opportunity.

Synergistic antitumor effect of TRAIL and adriamycin on the human breast cancer cell line MCF-7

The aim of the present study was to determine the effect of the combination of tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) and adriamycin (ADM) on the human breast cancer cell line MCF-7 and to identify potential mechanisms of apoptosis. Cell viability was analyzed by the MTT assay and the synergistic effect was assessed by the Webb coefficient. Apoptosis was quantified using the annexin V-FITC and propidium iodide staining flow cytometry. The mRNA expression of TRAIL receptors was measured by RT-PCR. Changes in the quantities of Bax and caspase-9 proteins were determined by Western blot. MCF-7 cells were relatively resistant to TRAIL (IC50 >10 µg/mL), while MCF-7 cells were sensitive to ADM (IC50 <10 µg/mL). A subtoxic concentration of ADM (0.5 µg/mL) combined with 0.1, 1, or 10 µg/mL TRAIL had a synergistic cytotoxic effect on MCF-7 cells, which was more marked with the combination of TRAIL (0.1 µg/mL) and ADM (0.5 µg/mL). In addition, the combined treatment with TRAIL and ADM significantly increased cell apoptosis from 9.8% (TRAIL) or 17% (ADM) to 38.7%, resulting in a synergistic apoptotic effect, which is proposed to be mediated by up-regulation of DR4 and DR5 mRNA expression and increased expression of Bax and caspase-9 proteins. These results suggest that the combination of TRAIL and ADM might be a promising therapy for breast cancer.

Comparison of bone quantity by ultrasound measurements of phalanges between white and black children living in Paraná, Brazil, with Europeans

The objective of this study was to determine bone quantity by ultrasound measurements of the proximal finger phalanges (AD-SoS = amplitude-dependent speed of sound) of healthy Brazilian schoolchildren living in Paraná, Brazil and to compare these values with European populations. The sample was composed of 1356 Brazilian schoolchildren of both genders (660 males, 696 females), aged 6 to 11 years, divided into white (840) and black (516) groups and compared to age- and gender-matched Europeans. AD-SoS of the schoolchildren increased significantly with age for both genders. Significantly higher AD-SoS values were observed for the white children (1916 ± 58) compared to their black counterparts (1898 ± 72) and for the female gender (1920 ± 61) compared to the male gender (1898 ± 66). Overall, the AD-SoS outcomes for females were similar to those of European studies. However, the AD-SoS of the Brazilian schoolchildren of both genders and skin colors was lower than that reported for children in Poland. AD-SoS outcomes for Brazilian schoolboys were similar to those obtained in Italian studies and were lower than those of the Spanish children. In conclusion, Brazilian schoolchildren of both genders and skin colors showed lower bone quantities than Polish children and Spanish males, and levels similar to Italian children and Spanish females.