Cu nanoparticles enable plasmonic-improved silicon photovoltaic devices

This work examines the effect of copper nanoparticles (Cu NPs) on the photocurrent efficiency of silicon photovoltaic (Si PV) devices. An optimized synthesis of stable Cu NPs is reported together with a procedure for their immobilization on the Si PV surface. A comprehensive analysis of the photocurrent and power dependence of the Cu NPs surface coverage and size is presented. A decrease in photoconversion was observed for wavelengths shorter than similar to 500 nm, due to the Cu interband absorption. In the low surface coverage limit, where the level of aggregation was found to be low, the surface plasmon resonance absorption dominates leading to a modest effect on the photocurrent response. As the number of aggregates increased with the surface coverage, the photocurrent efficiency also increased, and a maximum enhancement power conversion of 16% was found for a 54 +/- 6 NPs per mu m(2) PV cell. This enhancement was attributed to SPR light scattering and trapping into the Si PV device. Higher surface coverage yielded numerous aggregates which acted as a bulk coating and caused a decrease in both photocurrent and power measurements.

Effect of partial preferential orientation and distortions in octahedral clusters on the photoluminescence properties of FeWO4 nanocrystals

This communication is a report of our initial research to obtain iron tungstate (FeWO4) nanocrystals by the microwave-hydrothermal method at 170 degrees C for 45 min. X-ray diffraction patterns showed that the FeWO4 nanocrystals prepared with polyethylene glycol-200 have a partial preferential orientation in the (011) plane in relation to other nanocrystals prepared with sodium bis(2-ethylhexyl) sulfosuccinate and water. Rietveld refinement data indicates that all nanocrystals are monophasic with wolframite-type monoclinic structures and exhibit different distortions on octahedral [FeO6]/[WO6] clusters. High resolution transmission electron microcopy revealed an oriented attachment mechanism for the growth of aggregated FeWO4 nanocrystals. Finally, we observed that the photoluminescence properties of these nanocrystals are affected by partial preferential orientation in the (011) plane and distortions on [FeO6]/[WO6] clusters.

Structure and luminescent investigation of the Ln(III)-beta-diketonate complexes containing tertiary amides

The synthesis and photoluminescent properties of Ln(III)-thenoyltrifluoroacetonate and dibenzoylmethanate complexes (Ln = Eu(III) and Gd(III) ions) containing tertiary amides such as dimethylacetamide (DMA), dimethylformamide (DMF), and dimethylbenzamide (DMB) as neutral ligands are reported. The Ln complexes were characterized by elemental analysis, complexometric titration with EDTA, and infrared spectroscopy. Single-crystal X-ray structure data of the [Eu(DBM)(3).(DMA)] compound indicates that this complex crystallizes in the triclinic system, space group PT with the following cell parameters: a = 10.2580(3) angstrom, b = 10.3843(2) angstrom, c= 22.3517(5) angstrom, alpha = 78.906(2)degrees, beta = 78.049(2)degrees, lambda= 63.239(2)degrees, V= 2066.41(9) angstrom(3), and Z = 2. The coordination polyhedron for the Eu(III) complex may be described as an approximate C-2v distorted monocapped trigonal prism. The optical properties of the Eu(III) complexes were studied based on the intensity parameters and luminescence quantum yield (q). The values of the ohm(2) parameter of the Eu-DBM complexes are larger than those for the Eu-TTA complexes, indicating that the Eu(III) ion is in a more polarizable chemical environment in the former case. The geometries of the complexes have been optimized by using the Sparkle Model, and the results have been used to perform theoretical predictions of the ligand-to-metal energy transfer via direct and exchange Coulomb mechanisms. (C) 2012 Elsevier Ltd. All rights reserved.

beta-ZnMoO4 microcrystals synthesized by the surfactant-assisted hydrothermal method: Growth process and photoluminescence properties

In this communication, we investigate the effect of different surfactants: cetyltrimethylammonium bromide (CTAB), sodium dodecyl sulfate (SDS) and polyvinylpyrrolidone (PVP-K40) on the growth process of zinc molybdate (beta-ZnMoO4) microcrystals synthesized under hydrothermal conditions at 140 degrees C for 8 h. These microcrystals were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and photoluminescence (PL) measurements. XRD patterns proved that these crystals are monophasic and present a wolframite-type monoclinic structure. FE-SEM images revealed that the surfactants modified the crystal shapes, suggesting the occurrence of distinct crystal growth processes. The CTAB cationic surfactant promotes the hindrance of small nuclei that leads to the formation of rectangle-like crystals, SDS anionic surfactant induces a growth of irregular hexagons with several porous due to considerable size effect of counter-ions on the crystal facets, PVP-K40 non-ionic surfactant allows a reduction in size and thickness of plate-like crystals, while without surfactants have the formation of irregular plate-like crystals. Finally, the PL properties of beta-ZnMoO4 microcrystals were explained by means of different shape/size, surface defects and order-disorder into lattice. (C) 2011 Elsevier B.V. All rights reserved.

Comparing properties of natural biogenic with biomass burning particles in Amazonia.

The Large Scale Biosphere Atmosphere Experiment in Amazonia (LBA) is a long-term (20 years) research effort aimed at the understanding of the functioning of the Amazonian ecosystem. The strong biosphere-atmosphere interaction is a key component of the ecosystem functioning. Two aerosol components are the most visible: The natural biogenic emissions of particles and VOCs, and the biomass burning emissions. Two aerosol and trace gases monitoring stations were operated for 4 years in Manaus and Porto Velho, two very distinct sites, with different land use change. Manaus is a very clean and pristine site and Porto Velho is representative of heavy land use change in Amazonia. Aerosol composition, optical properties, size distribution, vertical profiling and optical depth were measured from 2008 to 2012. Aerosol radiative forcing was calculated over large areas. It was observed that the natural biogenic aerosol has significant absorption properties. Organic aerosol dominates the aerosol mass with 80 to 95%. Light scattering and light absorption shows an increase by factor of 10 from Manaus to Porto Velho. Very few new particle formation events were observed. Strong links between aerosols and VOC emissions were observed. Aerosol radiative forcing in Rondonia shows a high -15 watts/m² during the dry season of 2010, showing the large impacts of aerosol loading in the Amazonian ecosystem. The increase in diffuse radiation changes the forest carbon uptake by 20 to 35%, a large increase in this important ecosystem.

Sviluppo di metodi innovativi per la sintesi di nanoparticelle di interesse industriale

Among various nanoparticles, noble metal nanoparticles have attracted considerable attention due to their optical, catalytic and conducting properties. This work has been focused on the development of an innovative method of synthesis for the preparation of metal nanosuspensions of Au, Ag, Cu, in order to achieve stable sols, showing suitable features to allow an industrial scale up of the processes. The research was developed in collaboration with a company interested in the large scale production of the studied nanosuspensions. In order to develop a commercial process, high solid concentration, long time colloidal stability and particle size control, are required. Two synthesis routes, differing by the used solvents, have been implemented: polyol based and water based synthesis. In order to achieve a process intensification the microwave heating has been applied. As a result, colloidal nanosuspensions with suitable dimensions, good optical properties, very high solid content and good stability, have been synthesized by simple and environmental friendly methods. Particularly, due to some interesting results an optimized synthesis process has been patented. Both water and polyol based synthesis, developed in the presence of a reducing agent and of a chelating polymer, allowed to obtain particle size-control and colloidal stability by tuning the different parameters. Furthermore, it has been verified that microwave device, due to its rapid and homogeneous heating, provides some advantages over conventional method. In order to optimize the final suspensions properties, for each synthesis it has been studied the effect of different parameters (temperature, time, precursors concentrations, etc) and throughout a specific optimization action a right control on nucleation and growth processes has been achieved. The achieved nanoparticles were confirmed by XRD analysis to be the desired metal phases, even at the lowest synthesis temperatures. The particles showed a diameter, measured by STEM and dynamic light scattering technique (DLS), ranging from 10 to 60 nm. Surface plasmon resonance (SPR) was monitored by UV-VIS spectroscopy confirming its dependence by nanoparticles size and shape. Moreover the reaction yield has been assessed by ICP analysis performed on the unreacted metal cations. Finally, thermal conductivity and antibacterial activity characterizations of copper and silver sols respectively are now ongoing in order to check their application as nanofluid in heat transfer processes and as antibacterial agent.

Materiali Politiofenici Otticamente Attivi

Much effort has been devoted in the recent years to the investigation of optically active polythiophenes characterized by the presence of a chiral moiety linked to the 3-position of the aromatic ring. In addition to their potential technological applications as materials for enantioselective electrodes and membranes, chiral poly(thiophene)s offer the possibility of studying the structural changes accompanying the transition from the disordered state by following the variation of their chiroptical properties by circular dichroism (CD). In solution of a good solvent, that kind of polythiophenes doesn’t display any optical activity arising from the presence of dissymmetric conformation of the backbone, as shown by circular dichroism (CD) spectra. When the macromolecules begin to aggregate, as it occurs e.g. by addition of a poor solvent, or lowering the solution temperature, or when the macromolecules are assembled in the solid state as thin films obtained by solution casting or spin coating, significant CD bands are observed in the spectral region related to the electronic absorptions of the aromatic polythiophene chromophore. These CD bands are indicative of a chiral macromolecule arrangement of one prevailing chirality. The synthesis of -substituted polythiophenes can be carried out starting from the corresponding -substituted mono- or oligomeric thiophenic monomers under regioselective or regiospecific conditions in order to minimize or avoid the formation of head-to-head dyads unfavourably affecting the presence of coplanar conformations of thiophene rings as a consequence of steric interactions between the side-chain substituents, both in solution and in the solid state. To this regard, non-symmetrically substituted monomers require therefore to perform the polymerization in the presence of highly demanding catalysts and reaction condition, whereas with symmetrically substituted oligothiophenic monomers containing the -substituents located far apart from the reacting sites, it is instead possible to obtain regioregular macromolecules by adopting more simple and economic polymerization methods, such as, e. g., the chemical oxidative polymerization with iron (III) trichloride. In order to verify how the polymer structure affects its optical activity, further poly-3-alkylthiophenes, substituted by an enantiomerically pure chiral alkyl group, namely poli[3,3”-di[2((S)-(+)-2-methylbutoxy)ethyl]-2,2’:5’,2”-terthiophene] (PDMBOETT), poli[3,3’di[2((S)-(+)-2-methylbutoxy)ethyl]-2,2’-bitiofene] (PDMBOEBT), poli[3,3””-didodecyl-4’,3”’-di(S)-(+)-2-methylbutyl-2,2’:5’,2”:5”,2”’:5”’,2””-quinquethiophene (PDDDMBQT) have been synthesized and characterized by instrumental techniques. The spectroscopic behaviour of thin films of poly(DDDMBQT) has been investigated in the solid state under different sample preparation procedures. It was also compared with the behaviour of polymers previously made. The experimental results are interpreted in terms of influence of the side-chain substituents on the extent of planarity of the polymeric chains and the formation of optically active chiral aggregates. In recent years conjugated block copolymers have received considerable attention. It is well known that conjugated block copolymers composed of two electronically different blocks can have morphologic and optical properties, that differ from those of their homopolymers. A recent study has also shown that the electronic properties and the supramolecular organization of one conjugated block can also be influenced by the other block. In order to study better this behavior, a new conjugated block copolymers, composed of a regioregular hydrophylic block and a regioregular hydrophobic block namely poli[3[2-(2-metossietossi)etossi]metiltiofene]-co- poli[3(1-octilossi)tiofene], has been synthesized and characterized.

Hyperverzweigte Polyphenylene und redoxaktive Dendrimere

Die Doktorarbeit gliedert sich in zwei Abschnitte. Das erste Kapitel beschäftigt sich mit den hyperverzweigten Polyphenylenen. Es wurden Untersuchungen des Molekulargewichts in Abhängigkeit von der Monomerkonzentration und der Reaktionszeit durchgeführt. Die synthetisierten Polymere haben große Polydispersitäten, die durch fraktioniertes Fällen herabgesetzt werden können. Die Funktionalisierung der hyperverzweigten Polyphenylene mit unterschiedlichen Methoden führt zu verschiedenen Funktionen auf der Oberfläche der Polymere. Die chlormethylierten hyperverzweigen Polymere können als Makroinitiator für den Aufbau von Kern-Schale-Systemen genutzt werden. Mit Hilfe der ATRP-Polymerisation wurde Methylmethacrylat anpolymerisiert. Als Charakterisierungsmethode zur Bestimmung des freien Volumens findet die Positronenauslöschungsspektroskopie Anwendung. Im zweiten Teil der Arbeit stehen die Synthese und Charakterisierung von redoxaktiven Dendrimeren mit Triphenylamin- bzw. Naphthalinkern im Mittelpunkt. Den Einfluß der Dendrimerhülle auf die Redoxaktivität zeigen cyclovoltammetrische Untersuchungen. Die Zunahme der dendritischen Hülle führt zu einer Abschirmung des Redoxzentrums gegen die Elektrode und damit zu einer Inhibierung des Elektronentransfers. Das spiegelt sich in der Abnahme der Geschwindigkeitskonstanten sowie in der Ausdehnung der cyclovoltammetrischen Kurve wieder. Die Funktionalisierung der Triphenylamin-Dendrimere mit Chromophoren auf der Oberfläche führt zu einer Änderung der optische Eigenschaften, die mit Hilfe von Absorptions- und Emissionsmessungen untersucht wurden.

Squaraine mit ausgedehnter Konjugation

Squaraine mit ausgedehnter Konjugation: Die vorliegende Arbeit ist in zwei Teilbereiche gegliedert, wobei der erste Teil die Synthese und Eigenschaftsuntersuchung symmetrischer und unsymmetrischer, stilbenoider Squaraine mit ausgedehnter Konjugation (DAD-Systeme) betrifft. Im zweiten Teil der Arbeit werden als Modellverbindungen für diese Squaraine Oligo(phenylenvinylen)e (OPVs) mit terminaler Donor-Acceptor-Substitution hergestellt.Es wurden drei unterschiedliche Klassen von konjugationsverlängerten Squarainen synthetisiert: unsymmetrische und symmetrische Monosquaraine sowie Oligosquaraine mit zwei, drei oder vier quarylium-Einheiten. Um eine bessere Löslichkeit zu gewährleisten, tragen die meisten Verbindungen voluminöse, flexible Bis(2-hexyloctyl)amino-Reste. Teilweise konnte die Löslichkeit auch durch zusätzliche Hexylseitenketten noch weiter verbessert werden. Der Aufbau der stilbenoiden Resorcine, die zur Synthese der entsprechenden Squaraine benötigt werden, erfolgte fast ausschließlich über die Wittig-Horner-Reaktion. Die 3,5-Dihydroxysubstitution erhöht die Nucleophilie in der 4-Position, so daß sich die stilbenoiden Resorcine in guten Ausbeuten mit Quadratsäure oder mit einer Semiquadratsäure zu den gewünschten Squarainen kondensieren ließen. Die Herstellung der Donor-Acceptor-substituierten OPVs erfolgte nach einer konvergenten Synthesestrategie, bei der auf eine repetitive Wittig-Horner-Reaktion und eine einfache Schutzgruppentechnik zurückgegriffen wurde. Als Acceptorgruppen dienten Formyl-, Cyano- und Nitrosubstituenten, als Donorgruppe wurden Bis(2-Hexyloctyl)amino-Reste eingesetzt. Die igenschaftsuntersuchungen an den konjugierten Oligomeren konnten zur Aufklärung des ungewöhnlichen spektroskopischen Verhaltens der Squaraine beitragen. Es wurde ein athematischer Ansatz entwickelt, der das Absorptionsverhalten D-A-substituierter Oligo(phenylenvinylen)e exakt beschreiben kann. Semiempirische Rechnungen und elektrooptische bsorptionsmessungen an diesen Verbindungen bestätigten die experimentell gefundenen Trends.

Chemical and physical properties of Amazonian aerosol particles

- ZUSAMMENFASSUNG:Die vorliegende Dissertation befasst sich mit der Bestimmung der chemischen und physikalischen Eigenschaften von Aerosolpartikeln im Amazonasbecken, die während Zeiten mit Biomasseverbrennung und bei Hintergrundbedingungen bestimmt wurden. Die Messungen wurden während zwei Kampagnen im Rahmen des europäischen Beitrags zum LBA-EUSTACH Experiment in Amazonien. Die Daten umfassen Messungen der Anzahlkonzentrationen, Größenverteilungen, optischen Eigenschaften sowie Elementzusammensetzungen und Kohlenstoffgehalte der gesammelten Aerosole. Die Zusammensetzung des Aerosols wies auf folgende drei Quellen hin: natürlichen biogenen, Mineralstaub, und pyrogenes Aerosol. Aller drei Komponenten trugen signifikant zur Extinktion des Sonnenlichts bei. Insgesamt ergab sich eine Steigerung der Meßwerte um ca. das Zehnfache während der Trockenzeit im Vergleich zur Regenzeit, was auf eine massive Einbringung von Rauchpartikeln im Submikrometerbereich in die Atmosphäre während der Trockenzeit zurückzuführen ist. Dementsprechend sank die Einzelstreualbedo von ca. 0,97 auf 0,91. Der Brechungsindex der Aerosolpartikel wurde mit einer neuen iterative Methoden, basierend auf der Mie-Theorie berechnet. Es ergaben sich durchschnittliche Werte von 1,42 – 0,006i für die Regenzeit und 1,41 – 0,013i für die Trockenperiode. Weitere klimatisch relevante Parameterergaben für Hintergrundaerosole und für Aerosole aus Biomasseverbrennung folgende Werte: Asymmetrieparameter von 0,63 ± 0,02 bzw. 0,70 ± 0,03 und Rückstreuungsverhältnisse von 0,12 ± 0,01 bzw. 0,08 ± 0,01. Diese Veränderungen haben das Potential, das regionale und globale Klima über die Variierung der Extinktion der Sonneneinstrahlung als auch der Wolkeneigenschaften zu beeinflussen.

Donor-Akzeptor-substituierte Oligo(phenylenethinylen)e und Oligo(thienylenethinylen)e

Die Dissertation beschäftigt sich mit der Synthese und den Eigenschaftsuntersuchungen von Oligo(phenylenethinylen)en (OPEs) und Oligo(thienylenethinylen)en (OTEs) mit terminaler Donor-Akzeptor-Substitution. Die Darstellung der Oligomerenreihen erfolgt über ein „Baukastensystem“ bestehend aus Start,- Synthese, - und dem jeweiligen Endbaustein. Die zentrale Synthesereaktion zum Aufbau der Push-Pull-Systeme ist eine moderne und effektive Pd-katalysierte Reaktion, die Sonogashira-Hagihara-Kupplung. Für die dialkylaminosubstituierten OPE-Systeme konnten die Cyano,- Formyl,- Nitro –und Dicyanovinylgruppe als Akzeptoren eingeführt werden. In der dodecylsulfanylsubstituierten OTE-Serie wurde als Akzeptor die Nitrogruppe verwendet, während in der methoxysubstituierten OTE-Reihe die Formyl,- Nitro –und Dicyanovinylgruppe als Akzeptoren eingeführt wurde. Alle Reihen konnten mittels 1H-, 13C-, IR-, MS- und UV/Vis-Spektroskopie vollständig charakterisiert werden. Die Lage des langwelligen Absorptionsmaximums zeigt eine starke Abhängigkeit von der Donor- und Akzeptorstärke der Substituenten sowie von der Länge des konjugierten Pie-Systems. Für beide Pie-Systeme ergibt sich bei hinreichend starker Donor- und Akzeptorsubstitution eine ungewöhnliche hypsochrome Verschiebung der langwelligen Absorptionsmaxima. Mit Hilfe der semiempirischen Quantenmechanik wird ein Modell vorgestellt, das die ungewöhnlichen spektroskopischen Eigenschaften der OPEs und OTEs erklären und vorhersagen kann. Mittels elektrooptischer Absorptionsmessungen ( EOAM ), EFISHG-Messungen sowie der Frequenzverdreifachungsspektroskopie ( THG ) werden die NLO-Eigenschaften in Abhängigkeit von der Konjugationslänge der nitrosubstituierten OPE-Serie bestimmt.

Studio di metodi di preparazione e caratterizzazione di nanostrutture per la funzionalizzazione di materiali ceramici

This thesis was carried out in the context of a co-tutoring program between Centro Ceramico Bologna (Italy) and Instituto di Tecnologia Ceramica, Castellón de la Plana (Spain). The subject of the thesis is the synthesis of silver nanoparticles and at their likely decorative application in the productive process of porcelain ceramic tiles. Silver nanoparticles were chosen as a case study, because metal nanoparticles are thermally stable, and they have non-linear optical properties when nano-structured, and therefore they develop saturated colours. The nanoparticles were synthesized by chemical reduction in aqueous solution, a method chosen because of its reduced working steps and energy costs. Besides such a synthesis method uses non-expensive and non-toxic raw material. By adopting this synthesis technique, it was also possible to control the dimension and the final shape of the nanoparticles. Several syntheses were carried out during the research work, modifying the molecular weight of the reducing agent and/or the firing temperature, in order to evaluate the influence such parameters have on the Ag-nanoparticles formation. The syntheses were monitored with the use of UV-Vis spectroscopy and the average dimension as well as the morphology of the nanoparticles was analysed by SEM. From the spectroscopic data obtained from each synthesis, a kinetic study was completed, relating the progress of the reaction to the two variables (ie temperature and molecular weight of the reducing agent). The aim was finding equations that allow the establishing of a relationship between the operating conditions during the synthesis and the characteristics of the final product. The next step was finding the best method of synthesis for the decorative application. For such a purpose the amount of nanoparticles, their average particle size, the shape and the agglomeration are considered. An aqueous suspension containing the nanoparticles is then sprayed over the fired ceramic tiles and they are subsequently thermally treated in conditions similar to the industrial one. The colorimetric parameters of the obtained ceramic tiles were studied and the method proved successful, giving the ceramic tiles stable and intense colours.

Thin functional conducting polymer films

In the present study, thin functional conducting polyaniline (PANI) films, either doped or undoped, patterned or unpatterned, were prepared by different approaches. The properties of the obtained PANI films were investigated in detail by a combination of electrochemistry with several other techniques, such as SPR, QCM, SPFS, diffraction, etc. The sensing applications (especially biosensing applications) of the prepared PANI films were explored. Firstly, the pure PANI films were prepared by the electropolymerisation method and their doping/dedoping properties in acidic conditions were investigated in detail by a combination of electrochemistry with SPR and QCM. Dielectric constants of PANI at different oxidation states were obtained quantitatively. The results obtained here laid a good foundation for the following investigations of PANI films in neutral pH conditions. Next, PANI multilayer films doped by a variety of materials were prepared by the layer-by-layer method in order to explore their biosensing applications, because of the loss of redox activity of pure PANI in neutral pH conditions. The dopants used include not only the traditionally used linear polyelectrolytes, but also, for the first tim, some other novel materials, like modified gold nanoparticles or modified carbon nanotubes. Our results showed that all the used dopants could form stable multilayer films with PANI. All the obtained PANI multilayer films showed good redox activity in a neutral pH environment, which makes them feasible for bioassays. We found that all the prepared PANI multilayer films can electrocatalyze the oxidation of NADH in neutral conditions at a low potential, although their catalytic efficiencies are different. Among them, PANI/carbon nanotube system showed the highest catalytic efficiency toward the oxidation of NADH, which makes it a good candidate as a NADH sensor. Besides, because some of the prepared PANI multilayer systems were end-terminated with –COOH groups (like PANI/Au nanoparticles system), which can be utilized to easily link biomolecules for biosensing applications. Here, we demonstrated, for the first time, to use the prepared PANI multilayer films for the DNA hybridisation detection. The detection event was monitored either by direct electrochemical method, or by enzyme-amplified electrochemical method, or by surface plasmon enhanced fluorescence spectroscopic method. All the methods can effectively differentiate non-complementary DNA from the complementary ones, even at the single-base mismatch level. It should also be noted that, our success in fabricating PANI multilayer films with modified Au nanoparticles or carbon nanotubes also offered another novel method for incorporating such novel materials into (conducting) polymers. Because of the unique electrochemical and optical properties of each component of the obtained PANI multilayer films, they should also find potential applications in many other fields such as microelectronics, or for electrochromic and photovoltaic devices. Finally, patterned PANI films were fabricated by the combination of several patterning techniques, such as the combination of electrocopolymerization with micromolding in capillaries (EP-MIMIC), the combination of microcontact printing with the layer-by-layer technique (µCP-LBL), and the polystyrene (PS) template induced electropolymerisation method. Using the obtained stripe-shaped PANI/PSS film, a redox-switchable polymer grating based on the surface-plasmon-enhanced mode was constructed and its application in the field of biosensing was explored. It was found that the diffraction efficiency (DE) of the grating was very sensitive to the applied potential (i.e. redox state of the film) as well as the pH environment of the dielectric medium. Moreover, the DE could also be effectively tuned by an electrocatalytic event, such as the electrocatalytic oxidation of NADH by the grating film. By using PS colloidal crystal assemblies as templates, well-ordered 3D interconnected macroporous PANI arrays (PANI inverse opals) were fabricated via electropolymerisation method. The quality of the obtained inverse opals was much higher than those reported by chemical synthesis method. By electrochemical method, the structures of the prepared inverse opals can be easily controlled. To explore the possible biosensing applications of PANI inverse opals, efforts were also done toward the fabrication of PANI composite inverse opals. By selecting proper dopants, high quality inverse opals of PANI composites were fabricated for the first time. And the obtained opaline films remained redox-active in neutral pH conditions, pointing to their possible applications for electrobioassays.

Farbe und Funktion neuer Molekülarchitekturen auf Rylencarbonsäureimid-Basis

Perylencarbonsäureimide sind Farbmittel mit ausgezeichneter chemischer und photochemischer Stabilität, hohen molaren Extinktionskoeffizienten und hohen Fluoreszenzquantenausbeuten, weswegen ihre Anwendung über die reine Farbgebung hinausgeht und von der Grundlagenforschung bis hin zum funktionellen High-Tech-Material reicht. Ziel der vorliegenden Dissertation mit dem Titel „Farbe und Funktion neuer Molekülarchitekturen auf Rylencarbonsäureimid-Basis“ war die Synthese und Charakterisierung von neuen chromophoren Systemen ausgehend von bekannten Perylenfarbmitteln. Im ersten Teil der Arbeit wird die Synthese eines Konstruktes beschrieben, das es ermöglicht, die Rotation eines Perylenfarbstoffs einzelmolekülspektroskopisch zu visualisieren. Mit der Methode der defokussierten Einzelmolekülspektroskopie kann die Immobilisierung des molekularen Rotors nachgewiesen und die Umorientierung des Farbstoffs detektiert werden. In den folgenden Kapiteln steht die gezielte Variation bekannter chromophorer Systeme im Vordergrund. Die Veränderung der Größe, der Topologie und der Substitution des aromatischen π-Systems hat erheblichen Einfluss auf die optischen Eigenschaften sowie auf die Eignung der Moleküle als funktionelle Farbmittel, beispielsweise in optoelektronischen Bauteilen. Anhand der Eigenschaften der dargestellten Derivate können systematische Zusammenhänge zwischen Struktur, Farbe und Funktion abgeleitet werden.

Organokompatible Zinnoxid-Nanopartikel

In der vorliegenden Arbeit werden verschiedene Methoden der Synthese von Zinn(IV)oxid Nanopartikeln, deren Stabilisierung durch unterschiedliche Surfactants und der Einbau der Nanomaterialien in PMMA beschrieben und die erhaltenen Materialien charakterisiert. Die Darstellung der Zinnoxid Nanopartikel wurde über drei verschiedene Synthesewege durchgeführt: a) Polymeric Precursor Methode, b) Solvothermal-Synthese und c) säurekatalysierte Fällungsreaktion. Im Rahmen von a) konnte neben der thermodynamisch stabilen Phase von Zinn(IV)oxid ebenfalls die metastabile orthorhombische Phase synthetisiert werden. Durch eine Analyse der Pyrolysebedingungen konnte der Kristallisationsmechanismus des Zinnoxids ausgehend vom Precursor bis zur tetragonalen Phase des Zinn(IV)oxid diskutiert werden. Die Synthesemethoden b) und c) boten sich zur Darstellung von oberflächenmodifizierten Zinnoxid Nanopartikeln an. Als Surfactant benutzte man unter anderem Alkylphosphonsäuren, da eine hydrophobe Oberfläche die Dispersion in MMA ermöglichte. Abschließend wurde eine radikalische in situ-Polymerisation von MMA in Gegenwart von oberflächenmodifizierten Partikeln durchgeführt. Der erhaltene Verbundwerkstoff zeichnete sich durch eine erhöhte thermische Stabilität aufgrund weniger Strukturdefekte des Polymers aus. Durch eine Untersuchung des Polymerisationsmechanismus konnte die Wirkung der oberflächenmodifizierten Nanopartikel auf die Polymerisation veranschaulicht werden. Aufgrund der nicht homogenen Verteilung der Nanopartikel im Verbundwerkstoff konnte jedoch keine Charakterisierung der optischen Eigenschaften durchgeführt werden.