Tetraethylortossilicate plasma thin film with hydrophilic and hydrophobic characteristics: Use on passive mixers

This work aims to obtain plasma thin film composites with hydrophobic/hydrophilic alternated regions, which are useful for the production of miniaturized mixers. These regions were acquired by two different strategies: either the codeposition of TEOS and HFE plasma thin films or the exposition of TEOS plasma films to ultraviolet radiation (UVA and UVC). These films were characterized by several chemical and physical techniques. The refractive indexes vary from 1.4 to 1.7; infrared and photoelectron spectroscopy detect Si-O-Si and CHn species. Silicone-like structures with high or low number of amorphous carbon microparticles and with fluorinated organic clusters were produced. Cluster dimensions were in the 1-5 mm range and they are made of graphite or COF (carbon/oxygen/fluorine) compounds. Scanning electron and optical microscopy showed rough surfaces. Water contact angles were 90º; however, for TEOS films that value changed after 6 hr of UVC exposure. Moreover, after UV exposure, organic polar compounds could be adsorbed in those films and water was not. The passive mixer performance was simulated using the FemLab 3.2® program and was tested with 20 nm thick films on a silicon wafer, showing the capacity of these films to be used in such devices.

Composite Thin Film Obtained Using Tetraethoxysilane and Aimed at VOCs Detection

The aim of this work was production of tetraethoxysilane (TEOS) plasma polymerized thin films and optimization of their physical-chemical characteristic for sensor development. The films were analyzed using several techniques. It was possible to produce composites (graphite clusters imbibed by silicon oxide film) made from only one reactant (TEOS). Deposition rate can vary significantly, reaching a maximum of 30 nm/min; cluster formation and their size widely depending on deposition parameters. The film surface was hydrophobic but can be wetted by organic compounds, probably due to carbon radicals. These films are good candidates for sensor development.

A simple and portable instrument for determination of captopril in pharmaceutical formulations

Objective: This article describes the application and the performance of a cheap, simple and portable device that can be used for colorimetric quantitative determination of captopril (CPT) in pharmaceutical preparations. Methods: The sensor is a light detector resistor (LDR) placed into a black PTFE cell and coupled to a low cost multimeter (Ohmmeter). The instrument has been tested and is easy and fast to use. The quantitative study is based mainly on reduction of ammonium molybdate by captopril, in the presence of sulphuric acid, producing a green-yellow compound (max 407 nm). The calibration curves were obtained by plotting the electric resistance of the LDR against the CPT concentration on the range of 4.60 x 10-4 to 1.84 x 10-3 mol l-1 with a good coefficient of determination (R2 = 0.9962). Results: Statistical analysis of the obtained results showed no significant difference between the proposed methodology and the official reported method as evident from the t-test and variance ratio at 95% confidence level. Conclusion: The results of this study demonstrate that the instrument can be used for simple, accurate, precise, fast, in situ and low-cost colorimetric analysis of captopril in pharmaceuticals products.

Análise histológica e histomorfométrica do processo de reparo de defeitos ósseos em ratos diabéticos preenchidos com osso autógeno e recobertos por membrana de matriz óssea homógena ou por membrana de politetrafluoretileno

Pós-graduação em Odontologia - FOA

Análise estrutural do suporte de pastilha de grafite para lubrificação de roda ferroviária

This study aims to structurally evaluate a support of graphite pastille for the lubrication of railway wheels. The proper lubrication of wheel flanges of the railway extends the life of this component, so it is very important that this occurs lubrication to reduce the costs involved in railway maintenance. To prepar the evaluation structural will be used to International Electrotechnical Comission standard (IEC 61373) establishing which load cases should be applied to this component. The applied loads on the support (accordance with IEC) are random accelerations and accelerations due to shocks, thus simulating the conditions that exist along the route of the train. The structural analyzes are performed by the finite element method, with the aid of the Cosmos software. Thus, it is possible to determine the stresses acting on the support, and so the allowable stresses compared with the standard proposed by the AISC. The stress in the structural analyzes are lower than allowable therefore considered for the configuration presented, unexpected structural problems

Desenvolvimento de revestimentos siloxano-PMMA reforçados por nanotubos de carbono, óxido de grafite e óxido de grafite reduzido para aplicações anticorrosivas

Pós-graduação em Química - IQ

Espectroscopia de impedância eletroquímica da biodissolução da calcopirita na presença de íons ferrosos

Pós-graduação em Química - IQ

Estudo comparativo de filmes de corantes fenotiazínicos na superfície de eletrodo de carbono vítreo e adsorvidos em titânio fosfatado e suas aplicações eletroanalíticas

Pós-graduação em Ciência dos Materiais - FEIS

Quantificação eletroquímica de analitos de interesse ambiental e biológico, empregando novos materiais preparados a partir de silsesquioxanos funcionalizados

Pós-graduação em Ciência dos Materiais - FEIS

Metalloproteomic profile determination of muscle samples from nile Tilapia (Oreochromis niloticus) using AAS and ESI-MS/MS after 2D-PAGE separation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Direct preparation and characterization of copper pentacyanonitrosylferrate nanoparticles

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Voltammetric Behavior of a Chemically Modified Silsesquioxane with 4-Amino-5-Phenyl-4h-[1,2,4]-Triazole-3-Thiol and its Application for Detection of L-Dopamine

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Mercury fractionation in dourada (Brachyplatystoma rousseauxii) of the Madeira River in Brazil using metalloproteomic strategies

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Immunolocalization of markers for bone formation during guided bone regeneration in osteopenic rats

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The RANK/RANKL/OPG interaction in the repair of autogenous bone grafts in female rats with estrogen deficiency

The aim of this study was to evaluate the resorption process during the repair of autogenous bone grafts with or without coverage by an expanded polytetrafluoroethylene (e-PTFE) membrane in female rats with estrogen deficiency using the immunohistochemical technique. Eighty female rats were randomly divided into two groups (OVX and SHAM). The 40 female rats in the OVX group were subjected to ovariectomy, and the 40 female rats in the SHAM group were subjected to simulated ovariectomy. The two groups were further divided in subgroup E, which was subjected to surgery for placement of autogenous bone graft (ABG), and subgroup ME, in which the ABG was covered with an e-PTFE membrane. The animals were killed at 0, 7, 21,45 and 60 days. The specimens were analyzed using immunohistochemistry for the bone resorption markers RANK, RANK-L and Osteoprotegerin (OPG). A higher remodeling rate was observed at 7 and 21 days after the autogenous bone grafts, when the markers were more intensely expressed. At the final time point, the specimens presented similar characteristics to those observed at the initial time point. The expression of immunohistochemical markers was not altered by the estrogen deficiency. The presence of the e-PTFE membrane delayed the bone resorption process, influencing the immunohistochemical expression of markers.