Effect of the radiolitic sterilization in polyethylene/starch blends

Samples of LDPE/modified starch blends 80/20 m/m before and after exposure to gamma rays were examined by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction. The effect of gamma radiation is clearly seen in the samples irradiated at a dose of 25 kGy. The main alteration in the polymeric material after exposure at the radiation range was a decrease in the mechanical properties, alterations in the chemical structure of the blend with an increase in the carbonyl and vinyl indices and the appearance of new crystalline symmetry generating a crystalline domain not existing before in the blend.

Síntese e avaliação da atividade fitotóxica de derivados da α-Santonina

Mixtures of α-Santonin and various solvents were irradiated by either high or low pressure mercury lamps. The photochemical reactions afforded lumisantonin (11) (76% in acetonitrile), (3S,3aS,9bS)-3,6,6-trimethyl-3,3a,4,5-tetrahydronafto[1,2-b]furan-2,7(6H,9bH)dione (12) (100% in acetonitrile), 10α-acetoxy-3-oxo-1,7αH,6,11βH-guaia-4-en-6,12-olide (8) (26% in acetic acid), 10α-hydroxy-3-oxo-1,7αH,6,11βH-guaia-4-en-6,12-olide (10) (32%) and (E)-3-((3S,3aS,7aS)-3-methyl-2-oxo-6-(propan-2-ylidene)hexahydrobenzofuran-7-(7aH)-ylidene)propanoic acid (9) (44%) (in water/ acetic acid 1:1, v/v). Lactone 12 was also prepared by irradiation of lumisantonin in diethyl ether. Lactones 8 and 10 were converted, respectively, into the 10α-acetoxy-3β-hydroxy-1,7αH,6,11βH-guaia-4-en-6,12-olide (13) (87%) and 3β,10α-dihydroxy-1,7αH,6,11βH-guaia-4-en-6,12-olide (14) (75%) by sodium borohydride reduction. The effects of the compounds on the development of radicle of Sorghum bicolor and Cucumis sativus were evaluated.

Preparación de nanopartículas de plata en ausencia de polimeros estabilizantes

Silver nanoparticles (AgNPs) were prepared by means of the polyol method in the absence of stabilizing polymers. To accomplish this objective, AgNO3 was added to ethylene glycol in the presence of NaOH (1 mol.L-1), the suspension formed was irradiated with a microwave source for 60 seconds at a power of 465 watts. It was found that under these conditions AgNPs of sizes between 4-18 nm are formed. Also the results indicate that part of the ethylene glycol is oxidized to carbonyl compounds that reduce the Ag+. These organic compounds are adsorbed on the surfaces of AgNPs, forming a protective film that prevents their aggregation.

Degradação de poluentes emergentes por processos Fenton e foto-Fenton

A continuous photochemical treatment system was developed for aiming the treatment of aqueous solutions containing relevant micro-pollutants (microcystin-LR, sulfamethoxazole and 17-b estradiol). The continuous photo-Fenton process provided high degradation efficiency. However, contact time between samples and the irradiated region is short relative to total treatment time, indicating that observed changes are predominantly due to the Fenton process. Higher degradation efficiency was observed in systems operated using two treatment cycles, the first involving a batch Fenton process and the second a continuous photo-Fenton treatment.

Avaliação das propriedades de compósitos de polipropileno reforçados com casca de aveia

The preparation of oat-reinforced polypropylene nanocomposites with different fiber contents by means of melt-processing was investigated. Composite properties were evaluated by Scanning Electron Microscopy (SEM), Flexural Modulus, Dynamic Mechanical Analysis (DMA), Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA). Findings confirmed that the oat composite properties were affected by fiber type and content. Improvements in mechanical properties were obtained using fiber contents < 20% w.t.

Determinação de compostos carbonilados e carboxilados em derivados de petróleo

Although metals and nitrogen/sulfur compounds have been the main concern of the petroleum industry, issues concerning the harmful effects on catalysts poisoning and product contamination by other contaminants such as oxygen-containing compounds have been raised. Trace amounts of carbonyl and carboxyl compounds in petroleum products can lead to catalyst poisoning. Additionally, oxygenates may be present in final polyethylene and polypropylene resins, affecting the quality of food packaging. In this work, we reviewed potential analytical approaches for oxygenates determination in petroleum products and report the features of each potential technique.

1,3-propanodiol: produção, aplicações e potencial biotecnológico

1,3-propanediol is a high-value specialty chemical which has many industrial applications. Its main use is the production of the polymer polypropylene terephthalate, a thermoplastic used in the textile and automobile industries. The interest in 1,3-propanediol production from glycerol bio-conversion has increased after the employment of biodiesel by various countries, being produced by chemical synthesis from petroleum intermediates or biotechnologically by microbial fermentation. Glycerol is an abundant low-cost byproduct from biodiesel refineries, and it is the only substrate that can be naturally or enzymatically converted to 1,3-propanediol by microbial fermentation. In this review, information on 1,3-propanediol's importance, production and purification are presented, along with results from recent research on glycerol microbial conversion to 1,3-propanediol. The bio-production of this intermediate compound from glycerol is very attractive both economically and environmentally, since it allows the replacement of fossil fuels by renewable resources.

Design and implementation of a multipurpose reactor for scale-up studies

In the theoretical part, the different polymerisation catalysts are introduced and the phenomena related to mixing in the stirred tank reactor are presented. Also the advantages and challenges related to scale-up are discussed. The aim of the applied part was to design and implement an intermediate-sized reactor useful for scale-up studies. The reactor setting was tested making one batch of Ziegler–Natta polypropylene catalyst. The catalyst preparation with a designed equipment setting succeeded and the catalyst was analysed. The analyses of the catalyst were done, because the properties of the catalyst were compared to the normal properties of Ziegler–Natta polypropylene catalyst. The total titanium content of the catalyst was slightly higher than in normal Ziegler–Natta polypropylene catalyst, but the magnesium and aluminium content of the catalyst were in the normal level. By adjusting the siphonation tube and adding one washing step the titanium content of the catalyst could be decreased. The particle size of the catalyst was small, but the activity was in a normal range. The size of the catalyst particles could be increased by decreasing the stirring speed. During the test run, it was noticed that some improvements for the designed equipment setting could be done. For example more valves for the chemical feed line need to be added to ensure inert conditions during the catalyst preparation. Also nitrogen for the reactor needs to separate from other nitrogen line. With this change the pressure in the reactor can be kept as desired during the catalyst preparation. The proposals for improvements are presented in the applied part. After these improvements are done, the equipment setting is ready for start-up. The computational fluid dynamics model for the designed reactor was provided by cooperation with Lappeenranta University of Technology. The experiments showed that for adequate mixing with one impeller, stirring speed of 600 rpm is needed. The computational fluid dynamics model with two impellers showed that there was no difference in the mixing efficiency if the upper impeller were pumping downwards or upwards.

Creating carbon footprint calculating tool for plastic packaging products

The environmental challenges of plastic packaging industry have increased remarkably along with climate change debate. The interest to study carbon footprints of packaging has increased in packaging industry to find out the real climate change impacts of packaging. In this thesis the greenhouse gas discharges of plastic packaging during their life cycle is examined. The carbon footprint is calculated for food packaging manufactured from plastic laminate. The structure of the laminate is low density polyethylene (PE-LD) and oriented polypropylene (OPP), which have been joined together with laminating adhesive. The purpose is to find out the possibilities to create a carbon footprint calculating tool for plastic packaging and its usability in a plastic packaging manufacturing company. As a carbon footprint calculating method PAS 2050 standard has been used. In the calculations direct and indirect greenhouse gas discharges as well as avoided discharges are considered. Avoided discharges are born for example in packaging waste utilization as energy. The results of the calculations have been used to create a simple calculating tool to be used for similar laminate structures. Although the utilization of the calculating tool is limited to one manufacturing plant because the primary activity data is dependent of geographical location and for example the discharges of used energy in the plant. The results give an approximation of the climate change potential caused by the laminate. It is although noticed that calculations do not include all environmental impacts of plastic packaging´s life cycle.

Membrane emulsification in preparation of single site catalyst

In the theory part the membrane emulsification was studied. Emulsions are used in many industrial areas. Traditionally emulsions are prepared by using high shear in rotor-stator systems or in high pressure homogenizer systems. In membrane emulsification two immiscible liquids are mixed by pressuring one liquid through the membrane into the other liquid. With this technique energy could be saved, more homogeneous droplets could be formed and the amount of surfactant could be decreased. Ziegler-Natta and single-site catalysts are used in olefin polymerization processes. Nowadays, these catalysts are prepared according to traditional mixing emulsification. More homogeneous catalyst particles that have narrower particle size distribution might be prepared with membrane emulsification. The aim of the experimental part was to examine the possibility to prepare single site polypropylene catalyst using membrane emulsification technique. Different membrane materials and solidification techniques of the emulsion were examined. Also the toluene-PFC phase diagram was successfully measured during this thesis work. This phase diagram was used for process optimization. The polytetrafluoroethylene membranes had the largest contact angles with toluene and also the biggest difference between the contact angles measured with PFC and toluene. Despite of the contact angle measurement results no significant difference was noticed between particles prepared using PTFE membrane or metal sinter. The particle size distributions of catalyst prepared in these tests were quite wide. This would probably be fixed by using a membrane with a more homogeneous pore size distribution. It is also possible that the solidification rate has an effect on the particle sizes and particle morphology. When polymeric membranes are compared PTFE is probably still the best material for the process as it had the best chemical durability.

Natural and synthetic fibres improving tensile strength and elongation of paper products

The theory part of the Master’s thesis introduces fibres with high tensile strength and elongation used in the production of paper or board. Strong speciality papers are made of bleached softwood long fibre pulp. The aim of the thesis is to find new fibres suitable for paper making to increase either tensile strength, elongation or both properties. The study introduces how fibres bond and what kind of fibres give the strongest bonds into fibre matrix. The fibres that are used the in manufacturing of non-wovens are long and elastic. They are longer than softwood cellulose fibres. The end applications of non-wovens and speciality papers are often the same, for instance, wet napkins or filter media. The study finds out which fibres are used in non-wovens and whether the same fibres could be added to cellulose pulp as armature fibres, what it would require for these fibres to be blended in cellulose, how they would bind with cellulose and whether some binding agents or thermal bonding, such as hot calendaring would be necessary. The following fibres are presented: viscose, polyester, nylon, polyethylene, polypropylene and bicomponent fibres. In the empiric part of the study the most suitable new fibres are selected for making hand sheets in laboratory. Test fibres are blended with long fibre cellulose. The test fibres are viscose (Tencel), polypropylene and polyethylene. Based on the technical values measured in the sheets, the study proposes how to continue trials on paper machine with viscose, polyester, bicomponent and polypropylene fibres.

Elemental analysis of wood materials by external millibeam thick target PIXE

PIXE (Particle Induce X-ray Emission spectrometry) was used for analysing stem bark and stem wood of Scots pine, Norway spruce and Silver birch. Thick samples were irradiated, in laboratory atmosphere, with 3 MeV protons and the beam current was measured indirectly using a photo multiplicator (PM) tube. Both point scans and bulk analyses were performed with the 1 mm diameter proton beam. In bulk analyses, whole bark and sectors of discs of the stem wood were dry ashed at 550 ˚C. The ashes were homogenised by shaking and prepared to target pellets for PIXE analyses. This procedure generated representative samples to be analysed, but the enrichment also enabled quantification of some additional trace elements. The ash contents obtained as a product of the sample preparation procedure also showed to be of great importance in the evaluation of results in environmental studies. Spot scans from the pith of pine wood outwards, showed clearly highest concentrations of manganese, calcium and zinc in the first spot irradiated, or 2-3 times higher than in the surrounding wood. For stem wood from the crown part of a pine this higher concentration level was found in the first four spots/mms, including the pith and the two following growth rings. Zinc showed increasing concentrations outwards in sapwood of the pine stem, with the over-all lowest concentrations in the inner half of the sapwood. This could indicate emigration of this element from sapwood being under transformation to heartwood. Point scans across sapwood of pine and spruce showed more distinct variations in concentrations relative to hearth wood. Higher concentrations of e.g. zinc, calcium and manganese were found in earlywood than in denser latewood. Very high concentrations of iron and copper were also seen for some earlywood increments. The ash content of stem bark is up to and order higher than for the stem wood. However, when the elemental concentration in ashes of bark and wood of the same disc were compared, these are very similar – this when trees are growing at spots with no anthropogenic contamination from the atmosphere. The largest difference was obtained for calcium which appeared at two times high concentrations in ashes of bark than in ashes of the wood (ratio of 2). Pine bark is often used in monitoring of atmospheric pollution, where concentrations in bark samples are compared. Here an alternative approach is suggested: Bark and the underlying stem wood of a pine trees are dry ashed and analysed. The elemental concentration in the bark ash is then compared to the concentration of the same element in the wood ash. Comparing bark to wood includes a normalisation for the varying availability of an element from the soil at different sites. When this comparison is done for the ashes of the materials, a normalisation is also obtained for the general and locally different enrichment of inorganic elements from wood to bark. Already a ratio >2 between the concentration in the bark ash and the concentration in the wood ash could indicate atmospheric pollution. For monitoring where bark is used, this way of “inwards” comparison is suggested - instead of comparing to results from analyses of bark from other trees (read reference areas), growing at sites with different soil and, locally, different climate conditions. This approach also enables evaluation of atmospheric pollution from sampling of only relative few individual trees –preferable during forest felling.

Effects of light intensity modification by reflective aluminized screenhouse on sweet pepper growth and yield

Sweet pepper is one of the ten most consumed vegetables in world. Although it develops better under protected environment, the cultivation in tropical countries is practiced in open field due greenhouse structure higher costs. Unfortunately, such practice has compromised the crop to reach either best yield or fruit quality. Since production and cost are the most important criteria for agricultural production, we aimed to evaluate reflective aluminized polypropylene shading net influence on sweet pepper (Capsicum annuum L.) growth and production as intermediary alternative for low/middle income producers from Brazilian tropical regions. Sweet pepper Magali R hybrid was cultivated in two environments: FC - field conditions (control) and RS - reflective shading net with 40% shading rate. RS caused reductions in incident solar radiation (SR) and photosynthetically active radiation (PAR) on the amount of 46.3% and 48.3%, respectively. There were no significant changes in temperature and relative humidity recorded for the two environments. In addition, RS allowed best use efficiency of photosynthetically active radiation since it promoted higher values of plant height, leaf number and area index than those reached on FC on the amount of 29%, 22% and 80 %, respectively. Similarly, plants grown under RS showed higher yield and marketable fruits and promoted less loses by sunscald.

Hérnia traumática da parede abdominal

A rare case of blunt traumatic abdominal hernia is presented in which jejunal loops herniated through the abdominal wall. The patient had a serious motor vehicle accident seven years ago, while wearing the seat belt. He developed a traumatic hernia in the anterior lateral abdominal wall, which was operated, and relapsed after some months. The patient was reoperated and we observed the unattachment of the anterior lateral abdominal musculature from the ilium crest. After the hernial sac treatment, the defect was solved with the use of a polypropylene mesh. The postoperative evolution was good and four months later there were no signs of recurrence. Traumatic abdominal hernia remains a rare clinical entity, despite the increase in blunt abdominal trauma. Traumatic abdominal wall hernia falls into two general categories: small lower quadrant abdominal defects, typically the result of blunt trauma with bicycle handlebars, and larger abdominal wall defects related to motor vehicle accidents. The diagnosis may be often established by the physical examination alone. Conventional radiology and computerized tomography usefulness have been proved. In the vast majority of cases, early repair is recommended. The appropriate treatment is the reduction of the herniated bowel into the abdomen, the debridment of nonviable tissues, and a primary tension free closure of the detect.

Fotokatalyyttinen kalvonpesu

Fotokatalyysillä tarkoitetaan spontaania kemiallista reaktiota, joka tapahtuu fotokatalyytin absorboidessa valoa. Reaktio voi tapahtua joko katalyytin pinnalla tai sen läheisyydessä, mutta fotokatalyytti pysyy reaktiossa muuttumattomana. Ominaisuuksiltaan paras ja eniten tutkittu fotokatalyyttinen materiaali on titaanidioksidi, jolla on säteilytettynä kyky hajottaa orgaanisia molekyylejä hiilidioksidiksi ja vedeksi. Fotokatalyysin käyttömahdollisuuksia tutkitaan membraanikalvojen puhdistamisessa kalvojen käyttöiän ja erotustehokkuuden parantamiseksi. Nykyisin kalvojen puhdistamiseen käytetään useimmiten kemiallista pesua, jonka tuloksena on usein haitallisia yhdisteitä sisältävä liuos. Fotokatalyyttinen puhdistus voisi olla ratkaisu ongelmaan, sillä sen avulla voitaisiin puhdistamisessa käytettävien kemikaalien ja siinä muodostuvien jätteiden määrää vähentää. Tämän työn kokeellisessa osassa tutkittiin polyvinyylideenifluoridikalvon (PVDF) kestävyyttä ja puhdistumista fotokatalyyttisissä reaktioissa. PVDF:n on todettu olevan erinomainen kalvomateriaali, koska se on termisesti stabiili ja se kestää hyvin kemikaaleja, kuten orgaanisia liuottimia, happoja ja emäksiä. Työssä todettiin PVDF-kalvon puhdistuvan UV/TiO2-käsittelyn avulla. Kalvo puhdistui parhaiten, kun käytettiin 0,425 m- % TiO2-liuosta. Puhdistumista havainnoitiin sekä puhtaan veden vuon mittauksilla että värjäämällä käsiteltyjä kalvoja ja mittaamalla niiden värinintensiteetti.