Propagation of the Ignition Front against Airflow in Packed Beds of Wood Particles

Combustion of wood is increasing because of the needs of decreasing the emissions of carbon dioxide and the amount of waste going to landfills. Wood based fuels are often scattered on a large area. The transport distances should be short enough to prevent too high costs, and so the size of heating and power plants using wood fuels is often rather small. Combustion technologies of small-size units have to be developed to reach efficient and environmentally friendly energy production. Furnaces that use different packed bed combustion or gasification techniques areoften most economic in small-scale energy production. Ignition front propagation rate affects the stability, heat release rate and emissions of packed bed combustion. Ignition front propagation against airflow in packed beds of wood fuels has been studied. The research has been carried out mainly experimentally. Theoretical aspects have been considered to draw conclusions about the experimental results. The effects of airflow rate, moisture content of the fuel, size, shape and density of particles, and porosity of the bed on the propagation rate of the ignition front have been studied. The experiments were carried out in a pot furnace. The fuels used in the experiments were mainly real wood fuels that are often burned in the production of energy. The fuel types were thin wood chips, saw dust, shavings, wood chips, and pellets with different sizes. Also a few mixturesof the above were tested. Increase in the moisture content of the fuel decreases the propagation rates of the ignition front and makes the range of possible airflow rates narrower because of the energy needed for the evaporation of water and the dilution of volatile gases due to evaporated steam. Increase in the airflow rate increases the ignition rate until a maximum rate of propagation is reached after which it decreases. The maximum flame propagation rate is not always reached in stoichiometric combustion conditions. Increase in particle size and density transfers the optimum airflow rate towards fuel lean conditions. Mixing of small and large particles is often advantageous, because small particles make itpossible to reach the maximum ignition rate in fuel rich conditions, and large particles widen the range of possible airflow rates. A correlation was found forthe maximum rate of ignition front propagation in different wood fuels. According to the correlation, the maximum ignition mass flux is increased when the sphericity of the particles and the porosity of the bed are increased and the moisture content of the fuel is decreased. Another fit was found between sphericity and porosity. Increase in sphericity decreases the porosity of the bed. The reasons of the observed results are discussed.

Background, current status and future prospects of transgenic crop plant development

Les plantes transgèniques són una part integral de l’agricultura contemporània. Durant l’any 2006 més de noranta milions d’hectàrees de plantes transgèniques van ser cultivades en vint-i-un països. Des de la comercialització de la primera planta transgènica el 1996 els nivells d’adopció d’aquests cultius han augmentat anualment amb percentatges de dos dígits. El desenvolupament i la comercialització de les plantes transgèniques van lligats estretament al comerç mundial, a la globalització, a la disponibilitat de suficient menjar, a la protecció del medi ambient i del consumidor i a la propietat intel·lectual. En aquest article exposem els avenços més recents i les tendències actuals en el desenvolupament dels cultius transgènics i de la seva utilització. També ens fem ressò d’alguns assumptes no científics que s’han de solucionar abans que aquests cultius arribin al màxim del seu potencial, proporcionant una agricultura més sostenible i ecològica. Finalment, ressaltarem la importància de com les plantes transgèniques poden contribuir en la disponibilitat de menjar i en la millora de la pobresa en els països en vies de desenvolupament.

Growth and yield models in Spain: historical overview, contemporary examples and perspectives

En el presente trabajo se presenta una revisión sobre los modelos forestales desarrollados en España durante los últimos años, tanto para la producción maderable como no maderable y, para la dinámica de los bosques (regeneración, mortalidad). Se presentan modelos tanto de rodal completo como de clases diamétricas y de árbol individual. Los modelos desarrollados hasta la fecha se han desarrollado a partir de datos procedentes de parcelas permanentes, ensayos y el Inventario Forestal Nacional. En el trabajo se muestran los diferentes submodelos desarrollados hasta la fecha, así como las plataformas informáticas que permiten utilizar dichos modelos. Se incluyen las principales perspectivas de desarrollo de la modelización forestal en España.

Biblio-MetReS: A bibliometric network reconstruction application and server

Background: Reconstruction of genes and/or protein networks from automated analysis of the literature is one of the current targets of text mining in biomedical research. Some user-friendly tools already perform this analysis on precompiled databases of abstracts of scientific papers. Other tools allow expert users to elaborate and analyze the full content of a corpus of scientific documents. However, to our knowledge, no user friendly tool that simultaneously analyzes the latest set of scientific documents available on line and reconstructs the set of genes referenced in those documents is available. Results: This article presents such a tool, Biblio-MetReS, and compares its functioning and results to those of other user-friendly applications (iHOP, STRING) that are widely used. Under similar conditions, Biblio-MetReS creates networks that are comparable to those of other user friendly tools. Furthermore, analysis of full text documents provides more complete reconstructions than those that result from using only the abstract of the document. Conclusions: Literature-based automated network reconstruction is still far from providing complete reconstructions of molecular networks. However, its value as an auxiliary tool is high and it will increase as standards for reporting biological entities and relationships become more widely accepted and enforced. Biblio- MetReS is an application that can be downloaded from http://metres.udl.cat/. It provides an easy to use environment for researchers to reconstruct their networks of interest from an always up to date set of scientific documents.

Käyttöliittymä verkonhallintaan sulautetussa Linux-käyttöjärjestelmässä

During the project we get familiar with Linksys WRT54GL wireless router and its network managing methods. Operating system is OpenWRT which is Linux-based distribution for embedded devices. OpenWRT uses two kind of approach for its network administration. The first one is web-based user interface and the second one is command line based. Both methods are working but do not solve all problems that competent network administrator can need for secured network managing. The goal of the project was design an NCurses-based user interface for network administration that can be run from command line. The user interface can be use for example from terminal via SSH which is yet faster and also light to use. The idea is to combine the user friendly of WWW-interface and the advanced options that command line based network managing can offer. Linux-based open source OpenWRT offers good development tools. There exist also a compact development community if there is need for further development of software in future. So far user interface for command line based network administrator is not available.

Disseny d'una agenda cognitivament adaptada per a persones adultes amb discapacitat psíquica

El projecte que es presenta en aquesta memòria té com a objectiu el disseny d'una aplicació agenda amb tècniques orientades a l'usuari (Disseny Centrat en l'Usuari). Seguint aquestes metodologies es pretén dissenyar una agenda que aconsegueixi un grau de satisfacció alt per part dels usuaris, una part dels quals té unes habilitats cognitives especials, i un gestor d'agendes que agilitzi la coordinació als professionals de suport que treballen diàriament amb ells. L'objectiu final de les dues aplicacions és el mateix: millorar el benestar dels usuaris.

Polttoaineen reaktiivisuuden määrittäminen kiertoleijupoltossa

Kehitettäessä leijupolttotekniikkaa entistä ympäristöystävällisemmäksi ja tehokkaammaksi tarvitaan lisää tietoa polttoaineen käyttäytymisestä tulipesässä. Polttoaineen palamisprofiili ja reaktiivisuus vaikuttavat oleellisesti esimerkiksi voimalaitoskattilan lämmönsiirtopintojen sijoitteluun ja suunnitteluun sekä ohjausjärjestelmän toteutukseen. Varsinkin monipolttoainekattiloilla ohjausjärjestelmän toimivuus joutuu koetukselle esimerkiksi kuormanmuutostilanteissa ja äkillisissä polttoaineen syöttöhäiriöissä. Tässä työssä on aluksi tutustuttu kiertoleijupolton ilmiöihin ja niiden matemaattiseen mallintamiseen. Lisäksi esitetään katsaus eri prosessiolosuhteiden vaikutuksesta palamiseen kiertoleijuolosuhteissa. Työn tutkimusosassa kehitettiin menetelmä polttoaineen reaktiivisuuden määrittämiseksi kiertoleijupoltossa. Kehitetty menetelmä koostuu koesarjasta ja matemaattisesta simulointimallista. Koetoiminta suoritettiin VTT Energian laboratoriokokoluokan kiertoleijukoelaitteella. Koesarja polttoaineen reaktiivisuuden määrittämiseksi sisältää eri kaasukomponenttien profiilimittauksia ja dynaamisia muutoskokeita. Menetelmän avulla voidaan tutkia eri polttoaineiden reaktiivisuuksia sekä polttoaineen reaktiivisuuden ja tietyn prosessiolosuhteen välistä riippuvuutta. Suorittamalla koeajomatriisin mukaiset kokeet tietyissä prosessiolosuhteissa voidaan polttoaineen reaktiivisuus selvittää koetulosten ja simulointimallin perusteella.

Kunnossapidon materiaalilogistiikan merkitys ja organisoituminen kunnossapitoyhtiössä

Diplomityön tavoitteena on tutkia kunnossapitoyhtiöiden materiaalilogistiikan nykytilaa ja organisoitumista. Lisäksi työssä selvitetään materiaalilogistiikan merkittävimmät kehityskohteet ja ehdotetaan uutta organisoitumisratkaisua kunnossapitoyhtiön materiaalilogistiikkatoiminnoille. Työn teoriaosa käsittelee kunnossapidon ulkoistamista ja kunnossapidon materiaalilogistiikkaa. Soveltavassa osassa kuvataan materiaalilogistiikasta aiheutuvaa työkuormaa ja materiaalilogistiikan organisoitumista. Työssä käsitellään myös toimintatapoja ja tietojärjestelmien hyväksikäyttöä materiaalilogistiikkatoiminnoissa. Analysointi on toteutettu vierailemalla kunnossapitokohteissa ja mittaamalla materiaalilogistiikasta aiheutuvaa työkuormaa. Materiaalilogistiikka ei ole tehostunut, vaikka kunnossapitovastuu on siirtynyt kunnossapitoyhtiölle. Kunnossapitokohteiden materiaalilogistiikkatoiminnot perustuvat edelleen perinteisiin toimintatapoihin ja organisoitumiseen. Materiaalilogistiikkatoimintojen vastuita ei ole määritelty selkeästi. Materiaalilogistiikasta aiheutuva työkuorma on lähes 15 prosenttia kokonaistyöajasta kunnossapitokohteessa. Materiaalilogistiikkatoiminnoissa on tehtävä muutoksia lähitulevaisuudessa. Kunnossapitokohteissa on muutettava henkilöstön toimintatapoja ja materiaalilogistiikan organisoitumista.

Collective decision making in a heterogeneous environment: Lasius niger colonies preferentially forage at easy to learn locations

Many ants forage in complex environments and use a combination of trail pheromone information and route memory to navigate between food sources and the nest. Previous research has shown that foraging routes differ in how easily they are learned. In particular, it is easier to learn feeding locations that are reached by repeating (e.g. left-left or right-right) than alternating choices (left-right or right-left) along a route with two T-bifurcations. This raises the hypothesis that the learnability of the feeding sites may influence overall colony foraging patterns. We studied this in the mass-recruiting ant Lasius niger. We used mazes with two T-bifurcations, and allowed colonies to exploit two equidistant food sources that differed in how easily their locations were learned. In experiment 1, learnability was manipulated by using repeating versus alternating routes from nest to feeder. In experiment 2, we added visual landmarks along the route to one food source. Our results suggest that colonies preferentially exploited the feeding site that was easier to learn. This was the case even if the more difficult to learn feeding site was discovered first. Furthermore, we show that these preferences were at least partly caused by lower error rates (experiment 1) and greater foraging speeds (experiment 2) of foragers visiting the more easily learned feeder locations. Our results indicate that the learnability of feeding sites is an important factor influencing collective foraging patterns of ant colonies under more natural conditions, given that in natural environments foragers often face multiple bifurcations on their way to food sources.

Recommendations for malaria prevention in moderate to low risk areas: travellers' choice and risk perception.

BACKGROUND: The considerable malaria decline in several countries challenges the strategy of chemoprophylaxis for travellers visiting moderate- to low-risk areas. An international consensus on the best strategy is lacking. It is essential to include travellers' opinions in the decision process. The preference of travellers regarding malaria prevention for moderate- to low-risk areas, related to their risk perception, as well as the reasons for their choices were investigated. METHODS: Prior to pre-travel consultation in the Travel Clinic, a self-administered questionnaire was given to travellers visiting moderate- to low-risk malaria areas. Four preventive options were proposed to the traveller, i.e., bite prevention only, chemoprophylaxis, stand-by emergency treatment alone, and stand-by emergency treatment with rapid diagnostic test. The information was accompanied by a risk scale for incidence of malaria, anti-malarial adverse drug reactions and other travel-related risks, inspired by Paling palettes from the Risk Communication Institute. RESULTS: A total of 391 travellers were included from December 2012 to December 2013. Fifty-nine (15%) opted for chemoprophylaxis, 116 (30%) for stand-by emergency treatment, 112 (29%) for stand-by emergency treatment with rapid diagnostic test, 100 (26%) for bite prevention only, and four (1%) for other choices. Travellers choosing chemoprophylaxis justified their choice for security reasons (42%), better preventive action (29%), higher efficacy (15%) and easiness (15%). The reasons for choosing stand-by treatment or bite prevention only were less medication consumed (29%), less adverse drug reactions (23%) and lower price (9%). Those who chose chemoprophylaxis were more likely to have used it in the past (OR = 3.0 (CI 1.7-5.44)), but were not different in terms of demographic, travel characteristics or risk behaviour. CONCLUSIONS: When travelling to moderate- to low-risk malaria areas, 85% of interviewees chose not to take chemoprophylaxis as malaria prevention, although most guidelines recommend it. They had coherent reasons for their choice. New recommendations should include shared decision-making to take into account travellers' preferences.

Use of the dried blood spot sampling process coupled with fast gas chromatography and negative-ion chemical ionization tandem mass spectrometry: application to fluoxetine, norfluoxetine, reboxetine, and paroxetine analysis.

The objective of this work was to combine the advantages of the dried blood spot (DBS) sampling process with the highly sensitive and selective negative-ion chemical ionization tandem mass spectrometry (NICI-MS-MS) to analyze for recent antidepressants including fluoxetine, norfluoxetine, reboxetine, and paroxetine from micro whole blood samples (i.e., 10 microL). Before analysis, DBS samples were punched out, and antidepressants were simultaneously extracted and derivatized in a single step by use of pentafluoropropionic acid anhydride and 0.02% triethylamine in butyl chloride for 30 min at 60 degrees C under ultrasonication. Derivatives were then separated on a gas chromatograph coupled with a triple-quadrupole mass spectrometer operating in negative selected reaction monitoring mode for a total run time of 5 min. To establish the validity of the method, trueness, precision, and selectivity were determined on the basis of the guidelines of the "Société Française des Sciences et des Techniques Pharmaceutiques" (SFSTP). The assay was found to be linear in the concentration ranges 1 to 500 ng mL(-1) for fluoxetine and norfluoxetine and 20 to 500 ng mL(-1) for reboxetine and paroxetine. Despite the small sampling volume, the limit of detection was estimated at 20 pg mL(-1) for all the analytes. The stability of DBS was also evaluated at -20 degrees C, 4 degrees C, 25 degrees C, and 40 degrees C for up to 30 days. Furthermore, the method was successfully applied to a pharmacokinetic investigation performed on a healthy volunteer after oral administration of a single 40-mg dose of fluoxetine. Thus, this validated DBS method combines an extractive-derivative single step with a fast and sensitive GC-NICI-MS-MS technique. Using microliter blood samples, this procedure offers a patient-friendly tool in many biomedical fields such as checking treatment adherence, therapeutic drug monitoring, toxicological analyses, or pharmacokinetic studies.

From 'Security for Privacy' to 'Privacy for Security'

This article envisions the use of context-awareness to improve single sign-on solutions (SSO) for mobile users. The attribute-based SSO is expected to increase users' perceived ease of use of the system and service providers' authentication security of the application. From these two features we derive two value propositions for a new business model for mobile platforms. The business model can be considered as an instantiation of the privacy-friendly business model pattern presented in our previous work, reinforcing our claim that privacy-friendly value propositions are possible and can be used to obtain a competitive advantage.

Supporting Business Model Modelling: a Compromise between Creativity and Constraints

Diagrams and tools help to support task modelling in engi- neering and process management. Unfortunately they are unfit to help in a business context at a strategic level, because of the flexibility needed for creative thinking and user friendly interactions. We propose a tool which bridges the gap between freedom of actions, encouraging creativity, and constraints, allowing validation and advanced features.

Kaasutuskaasun puhdistus

Tässä diplomityössä on selvitetty hiilestä, jätteestä tai biopolttoaineesta kaasutetun kaasun märkä- ja kuivapuhdistusta. Kaasutuskaasun puhdistuksella voidaan likainen ja jopa ongelmallinen aines muuttaa tai puhdistaa sellaiseksi ympäristökelpoiseksi polttoaineeksi, että sitä voidaan käyttää nykyisissä kulutuskohteissa ongelmitta. Lisäkannustusta kaasutuskaasun puhdistus saa uusista EU-direktiiveistä, jotka tulevat rajoittamaan jätteiden läjittämistä kaatopaikoille. Loppusijoitukseen meneviä jätevirtoja voidaan energiakäytöllä pienentää huomattavasti.Työ on tehty PVO-Engineering Oy:n voimalaitostekniikan osastolle kevään 2001 aikana. Työn tavoitteena oli kasvattaa yrityksen tietomäärää kaasutuskaasun puhdistuksen osalta. Lisäksi pyrittiin selvittämään uuden keraamisen pussisuodatinmateriaalin käyttöä kaasutuskaasun kuumakuivasuodatuksessa. Työn ensimmäisessä osassa esitetään kaasutuskaasun koostumuksen ja syntymisen lisäksi tämän työn lähtökohdat ja tavoitteet. Toisessa osassa selvitetään kaasulle asetettavia vaatimuksia eri käyttötapojen mukaan. Kolmannessa ja neljännessä osassa selvitetään puhdistettavien komponenttien käyttäytymistä ja sopivia puhdistusmenetelmiä.Kaasutuskaasun puhdistustekniikka vaihtelee paljonkin riippuen kaasun käyttökohteesta. Eroja syntyy käyttökohteen asetettamista vaatimuksista polttoaineelle, kaasutettavan polttoaineen koostumuksesta ja laadun vaihtelusta. Puhdistuksessa keskitytään kloori -, rikki -, typpi - ja metalliyhdisteiden poistamiseen kaasuvirrasta. Erotuskyvyllä arvioituna eri puhdistusmenetelmistä tehokkaimpia ovat pesurisähkösuodatinyhdistelmät. Niiden suuret jätemäärät ovat kuitenkin iso ongelma. Kuumakuivapuhdistuksessa pyritään kehittämään menetelmä, jossa syntyvät jätemäärät ovat pieniä ja puhdistustulos on riittävä. Puhdistuksen apukeinona käytetään usein erilaisia katalyyttejä. Tunnetuimpia ovat erilaiset kalsiumpohjaiset materiaalit ja mineraalit. Katalyyteillä voidaan tehostaa tarpeellisia kemiallisia reaktioita puhdistusprosessissa. Kaikki puhdistukseen liittyvät ongelmat ovat kooltaan niin suuria, että niiden ratkaisemiseksi on tulevaisuudessa tehtävä lujasti töitä. Markkinanäkymät toimivalle puhdistustekniikalle ovat nykymaailmassa hyvät. Niinpä tuotekehitykseen laitetut panokset voivat tulevaisuudessa olla yritykselle kullan arvoisia.

Visualizing Business Model Evolution with the Business Model Canvas: Concept and Tool

The Business Model Canvas (BMC) assists in the design of companies' business models. As strategies evolve so too does the business model. Unfortunately, each BMC is a standalone representation. Thus, there is a need to be able to describe transformation from one version of a business model to the next as well as to visualize these operations. To address this issue, and to contribute to computer-assisted business model design, we propose a set of design principles for business model evolution. We also demonstrate a tool that can assist in the creation and navigation of business model versions in a visual and user-friendly way