973 resultados para Corpos algébricos
Resumo:
In this work is the addition of a metallic ion, of the metal Manganese, in a clay of Rio Grande do Norte state for structural ceramics use, the objective this study was to assess the evolution of ceramic properties. The clay was characterized by Chemical and Thermal analysis and Xray difraction. The metallic ion was added in the clay as aqueous solutions at concentrations of 100, 150 and 200 mg / L. The molded by extrusion and the burned were temperatures at 850, 950, 1050 and 1150 º C. Was made Chemical Analysis and investigated the following parameters environmental and ceramic: Solubility, Colour, Linear Retraction (%), Water Absorption (%), Gresification Curves, Apparent Porosity (%), Apparent Specific Mass (g/cm3) and Flexion Rupture Module (kgf/cm2). The results showed that increasing the concentration of metallic ion, properties such as Apparent Porosity (%), Water Absorption (%) decreases and the Flexion Rupture Module (kgf/cm2) increases with increasing temperature independent of the concentration of the ion. The gresification curves showed that the optimum firing temperatures were in the range between 950 and 1050 ° C. The evaluation of the properties showed that the ceramic material can be studied its use in solid brick and ceramic materials with structural function of filling. The results of solubility showed that the addition of ion offers no risk to the environment
Resumo:
Among the pests that attack corn crop in Brazil, there is Spodoptera frugiperda (JE Smith, 1797) (Lepidoptera: Noctuidae), known as fall armyworm, which is the major corn pest. Due to genetic instability during serial passage of baculoviruses in insect cell culture, the viral bioinseticides in vitro production development is the greatest challenge for mass production of this bioproduct. Successive passages of virus using extracellular viruses (BVs), necessary during viral bioinseticides production scaling up, leads to the appearance of aberrant forms of virus, a process so called as "passage effect ". The main consequence of passage effect is the production of occlusion bodies (OB) decrease, preventing its production using in vitro process. In this study, it was carried out a serial passage of baculovirus Spodoptera frugiperda multiple nucleopolyhedrovirus, isolate 18, using Sf21 cells. A decrease in the production of occlusion bodies from 170 to 92 in the third to fourth passage was observed. A factorial experimental design (22) was employed to verify the influence of two input variables, concentration of the hormone 20 - hydroxyecdysone (CH) and cholesterol (CC) on the values of response variables (volumetric and the specific OB production) of the process, seeking to define the optimum operating ranges trying to reverse or minimize the passage effect. The result indicated a negative influence of the cholesterol addition and positive effect in the hormone supplementation which the optimum range found for the concentrations studied were 8 to 10μg/mL and 5 to 6.5 mg / mL, for cholesterol and hormone concentrations respectively. New experiments were performed with addition of hormone and cholesterol in order to check the influence of these additives on the OB production independently. While the best result obtained from the factorial experiment was 9.4 x 107 OB/mL and 128.4 specific OB/cell, with the addition of only 6μg/mL 20-hydroxyecdysone these concentrations increased to 1.9 x 108 OB/mL and 182.9 OB/cell for volumetric and specific OB production, respectively. This result confirms that the addition of the hormone 20-hydroxyecdysone enhances the SfMNPV in vitro production process performance using Sf21 cells
Resumo:
Environmental sustainability has become one of the topics of greatest interest in industry, mainly due to effluent generation. Phenols are found in many industries effluents, these industries might be refineries, coal processing, pharmaceutical, plastics, paints and paper and pulp industries. Because phenolic compounds are toxic to humans and aquatic organisms, Federal Resolution CONAMA No. 430 of 13.05.2011 limits the maximum content of phenols, in 0.5 mg.L-1, for release in freshwater bodies. In the effluents treatment, the liquid-liquid extraction process is the most economical for the phenol recovery, because consumes little energy, but in most cases implements an organic solvent, and the use of it can cause some environmental problems due to the high toxicity of this compound. Because of this, exists a need for new methodologies, which aims to replace these solvents for biodegradable ones. Some literature studies demonstrate the feasibility of phenolic compounds removing from aqueous effluents, by biodegradable solvents. In this extraction kind called "Cloud Point Extraction" is used a nonionic surfactant as extracting agent of phenolic compounds. In order to optimize the phenol extraction process, this paper studies the mathematical modeling and optimization of extraction parameters and investigates the effect of the independent variables in the process. A 32 full factorial design has been done with operating temperature and surfactant concentration as independent variables and, parameters extraction: Volumetric fraction of coacervate phase, surfactant and residual concentration of phenol in dilute phase after separation phase and phenol extraction efficiency, as dependent variables. To achieve the objectives presented before, the work was carried out in five steps: (i) selection of some literature data, (ii) use of Box-Behnken model to find out mathematical models that describes the process of phenol extraction, (iii) Data analysis were performed using STATISTICA 7.0 and the analysis of variance was used to assess the model significance and prediction (iv) models optimization using the response surface method (v) Mathematical models validation using additional measures, from samples different from the ones used to construct the model. The results showed that the mathematical models found are able to calculate the effect of the surfactant concentration and the operating temperature in each extraction parameter studied, respecting the boundaries used. The models optimization allowed the achievement of consistent and applicable results in a simple and quick way leading to high efficiency in process operation.
Resumo:
Polyurethanes are very versatile macromolecular materials that can be used in the form of powders, adhesives and elastomers. As a consequence, they constitute important subject for research as well as outstanding materials used in several manufacturing processes. In addition to the search for new polyurethanes, the kinetics control during its preparation is a very important topic, mainly if the polyurethane is obtained via bulk polymerization. The work in thesis was directed towards this subject, particularly the synthesis of polyurethanes based castor oil and isophorone diisocianate. As a first step castor oil characterized using the following analytical methods: iodine index, saponification index, refraction index, humidity content and infrared absorption spectroscopy (FTIR). As a second step, test specimens of these polyurethanes were obtained via bulk polymerization and were submitted to swelling experiments with different solvents. From these experiments, the Hildebrand parameter was determined for this material. Finally, bulk polymerization was carried out in a differential scanning calorimetry (DSC) equipment, using different heating rates, at two conditions: without catalyst and with dibutyltin dilaurate (DBTDL) as catalyst. The DSC curves were adjusted to a kinetic model, using the isoconversional method, indicating the autocatalytic effect characteristic of this class of polymerization reaction
Resumo:
An evaluation project was conducted on the technique of treatment for effluent oil which is the deriving process to improve cashews. During the evaluation the following techniques were developed: advanced processes of humid oxidation, oxidative processes, processes of biological treatment and processes of adsorption. The assays had been carried through in kinetic models, with an evaluation of the quality of the process by means of determining the chemical demand of oxygen (defined as a technique of control by means of comparative study between the available techniques). The results demonstrated that the natural biodegradation of the effluent ones is limited, as result using the present natural flora in the effluent one revealed impracticable for an application in the industrial systems, independent of the evaluation environment (with or without the oxygen presence). The job of specific microorganisms for the oily composite degradation developed the viability technique of this route, the acceptable levels of inclusion in effluent system of treatment of the improvement of the cashew being highly good with reasonable levels of removal of CDO. However, the use combined with other techniques of daily pay-treatment for these effluent ones revealed to still be more efficient for the context of the treatment of effluent and discarding in receiving bodies in acceptable standards for resolution CONAMA 357/2005. While the significant generation of solid residues the process of adsorption with agroindustrial residues (in special the chitosan) is a technical viable alternative, however, when applied only for the treatment of the effluent ones for discarding in bodies of water, the economic viability is harmed and minimized ambient profits. Though, it was proven that if used for ends of I reuse, the viability is equalized and justifies the investments. There was a study of the photochemistry process which have are applicable to the treatment of the effluent ones, having resulted more satisfactory than those gotten for the UV-Peroxide techniques. There was different result on the one waited for the use of catalyses used in the process of Photo. The catalyses contained the mixing oxide base of Cerium and Manganese, incorporated of Potassium promoters this had presented the best results in the decomposition of the involved pollutants. Having itself an agreed form the gotten photochemistry daily paytreatment resulted, then after disinfection with chlorine the characteristics next the portability to the water were guarantee. The job of the humid oxidation presented significant results in the removal of pollutants; however, its high cost alone is made possible for job in projects of reuses, areas of low scarcity and of raised costs with the capitation/acquisition of the water, in special, for use for industrial and potable use. The route with better economic conditions and techniques for the job in the treatment of the effluent ones of the improvement of the cashew possesses the sequence to follow: conventional process of separation water-oil, photochemistry process and finally, the complementary biological treatment
Resumo:
This work aims at studying the influence of the concentration of calcite, its grain size and sintering temperature to obtain porous coating formulations that meet the design specifications. The experiments involved the physical-chemical and mineralogical caracterization of the raw materials, and mechanical tests on specimens dried and sintered, performing a planning mixture and factorial experiment, using the response surface methodology. The ceramic bodies studied were prepared by dry process, characterized, placed in conformity by uniaxial pressing and sintered at temperatures of 940 º C, 1000ºC, 1060ºC, 1120°C and 1180°C using a fast-firing cycle. The crystalline phases formed during sintering at temperatures under study, revealed the presence of anorthite and wolastonite, and quartz-phase remaining. These phases were mainly responsible for the physical and mechanical properties of the sintered especimens. The results shown that as increases the participation of carbonate in the composition of ceramic bodies there is an increase of water absorption and a slight reduction in linear shrinkage for all sintering temperatures. As for the mechanical strength it was observed that it tended to decrease for sintering at temperatures between 940 ° C and 1060 ° C and to increase for sintering at temperatures above 1060 ° C occurring with greater intensity for compositions with higher content of calcite. The resistence decreased with increasing participation of quartz in all sintering temperatures. The decrease in grain size of calcite caused a slight increase in water absorption for formulation with the same concentration of carbonate, remaining virtually unchanged the results of linear shrinkage and mechanical strength. In conclusion, porous ceramic coating (BIII) can be obtained using high concentrations of calcite and keeping the properties required in technical standards and that the particle size of calcite can be used as tuning parameter for the properties of ceramic products.
Estudo da circulação hidrodinâmica e da dispersão de óleo na zona costeira entre Macau e Galinhos RN
Resumo:
This paper presents a study on coastal hydrodynamics and the spread of an oil spill in waters off Macau and Galinhos, on the east coast of the state of Rio Grande do Norte in Northeast Brazil. This area has a very marked coastal dynamic owing to the complexity of its geomorphological features, developed in a regime of semidiurnal mesotides involving reefs, spits, estuaries, mangroves, lakes and dunes. The region also plays an important role in the socioeconomic development of the state, given that the production of oil, natural gas, salt and shrimp is concentrated there. The series of oil platforms is interconnected by a pipeline system that carries oil to the local terminal. This pipeline could leak at any moment, causing immense ecological damage. To gauge the risks of an oil leak and resulting contamination of the coastal region, two hydrodynamic scenarios were simulated. The results obtained were used to implement a contaminant transport model with the creation of various oil leak scenarios modeled at different volumes (from small to large) and intensities (sporadic and continuous), at points considered critical for the model (on two platforms and at two pipeline intersections), under different wind (summer and winter) and tidal (high and low at new, full and quarter moon phases) conditions. The use of hydrodynamic circulation computer models as a tool for representing a real project design has been increasingly frequent in recent years, given that they enable the realistic simulation of the hydrodynamic circulation pattern in bodies of water and an analysis of the impacts caused by contaminants released into the water. This study used the computer models contained in SisBAHIA®, in continuous development in the area of Coastal Engineering and Oceanography at COPPE/UFRJ
Resumo:
In Natal still dominates the use of individual disposal systems for domestic sewage, once only 29% of the city has a sewarage system. Wastes that are accumulated in these individual treatment systems should be exhausted periodically, service provided by collector entrepreneurs. Some of these companies causing major damage to the environment. In Natal, only two companies have their own septage (RESTI) treatment system, which were designed with parameters from domestic sewage generating strain and inefficient systems. Therefore, the characterization becomes essential as a source of parameters for their design. Thus, this work presents the physical-chemical and microbiological characterization of waste pumped from individual sewage treatment systems. Samples collections were made weekly from 5 different trucks at the reception point on the treatment plant on the point of the preliminary treatment. From each truck it was taken 5 samples during the discharge in order to make a composite sample. Afterwards, samples were carried out to laboratory and analyses for determination of temperature, pH, conductivity, BOD, COD, nitrogen (ammonia e organic), alkalinity, oils, phosphorus, solids, faecal coliforms and helminth egg. The results were treated as a single database, and ranked according to its generating source (multi and single house, lodging, health, services and / or food), area of origin (metropolitan, south and north) and type of system (cesspits, septic tank and / or sink). Through these data it was possible to verify that the type of system adopted by most in Natal and the metropolitan region is cesspit, besides to confirm the difference between the septage of areas with a population have different social and economical characteristics. It was found that the septage have higher concentrations than domestic sewage, except for thermotolerant coliforms that showed concentrations of 1,38E+07. Among the parameters studied, is the median values identified for COD (3,549 mg / L), BOD (973mg / L) and total solids (3.557mg / L). The volatile fraction constitutes about 70% of the total solids of the septage. For helminths has been a median of 7 eggs/L. In general, the characteristics of the waste followed the variability found in the literature reviewed for all variables, showing high amplitudes
Resumo:
The improper disposal of nitrogen in receiving water courses causes problems such as toxicity to living beings through the consumption of oxygen to meet the nitrogen demand, eutrophication and nitrate contamination of aquifers. For this reason it is often necessary to be carried out complementary treatment of wastewater to eliminate or reduce the concentration of this compound in the wastewater. The objective of this study is to evaluate the biological removal of nitrogen compounds using submerged aerated and anoxic filters as post-treatment of an anaerobic system, with low cost and innovative technology, which in previous studies has shown high removal efficiency of organic matter and great potential biological nitrogen compounds removal. The simple design with perforated hoses for air distribution and filling with plastic parts proved to be very efficient in relation to organic matter removal and nitrification. The system presented, in the best stage, efficiency in converting ammonia to nitrate by 71%, and produced a final effluent concentration below 10 mg / L of NH3-N. In addition, carbon concentration was removed by 77%, producing final effluent with 24 mg/L COD. However, denitrification in anoxic filter was not effective even with the addition of an external carbon source. There was a reduction of up to 56% of nitrogen caused by the process of simultaneous nitrification and denitrification (SND). The high voids space presented by this type of support material coupled with direct aeration of the sludge, allows the respiration of biomass retained between the endogenous phase, increased cell retention time and sludge retention capacity, producing a final effluent with turbidity less than 5 UT and total suspended solids around 5.0 mg/L
Resumo:
The potentially toxic cyanobacterial blooms in water bodies are spread across the globe, resulting in the loss of water quality and adverse effects on human health. In arid and semiarid regions, the hydrologic regime characterized by an annual cycle of drought and rain, change the volume and the retention time of the reservoir. Such changes affect the limnological characteristics and causing changes in composition and biomass community of cyanobacteria. The reservoir Cruzeta (Zmax = 8.7 m) is a eutrophic water supply source located in the semiarid tropical (Northeast Brazil). Raised the hypothesis that the hydrological regime of semi-arid tropical is a determining factor in the availability of resources in eutrophic water sources, which influences the composition of dominant species of cyanobacteria. The aim of this study was to analyze the changes in biomass and species composition of cyanobacteria for two annual hydrological cycles and evaluate factors drivers. The study was divided into five distinct periods (dry 2010, rain 2011, dry 2011, rain 2012, dry 2012). The dominant group found in all periods was Cyanobacteria (99% of total biomass), which contributed to the low diversity. The filamentous species Cylindrospermopsis raciborskii was present at both points in almost every study. The colonial species Microcystis panniformis and Sphaerocavum brasiliensis dominated only in periods with lower volumes of water. The diatoms contribute more to the biomass during the period of severe drought. The point near the dam (P1) had phytoplankton biomass larger than the point near the tributary (P2). The dominant species of colonial cyanobacteria lasted until the overflow in P1, and P2 this dominance was until the first rains. The redundancy analysis indicated that physical factors such as light availability and water level were the main factors driving the seasonal succession of phytoplankton. The composition of phytoplankton in spring was alternated by species of filamentous cyanobacteria in conditions of poor stability of the water column, such as Cylindrospermopsis raciborskii, and colonial species under conditions of high stability of the water column, such as Microcystis panniformis and Sphaerocavum brasiliensis. The extremes of torrential rains and severe droughts, governed by the hydrological regime of the semi-arid region led to the availability of resources in the watershed, directing the spatial and temporal dynamics of phytoplankton in the reservoir Cruzeta
Resumo:
The aquatic ecosystems can play a role as carbon-dioxide-source or carbon-dioxide-sink systems due to the high predominance of heterotrophic or autotrophic metabolism. The primary production can strongly affect the carbon balance (CO2) through the consumption of carbon dioxide in the photosynthesis, especially in eutrophic environment, acting as a carbon sink. The present study tested the hypothesis that the eutrophic reservoirs in tropical semi-arid region are carbon dioxide-sink systems due to the high primary productivity presented in these systems. Five Brazilian reservoirs from the semi-arid in the northeast region were monitored monthly during four years (2010 to 2013) with a prolonged drought event identified during the study. The results showed an increasing level of eutrophication over the period of prolonged drought, with the predominance of autotrophy. Significant negative correlations were observed between the partial pressure of CO2 (pCO2) (p<0,001) and chlorophyll-a in the Boqueirão, Passagem das Traíras, Dourado and Gargalheiras reservoirs, showing a pattern of the carbon dioxide-sink systems. However, this pattern was not found in Cruzeta reservoir. In summary, in the tropical semi-arid region, hydrological and morphometric variables can lead to different behaviors of the water-supply reservoirs on the carbon metabolism. The eutrophic reservoirs evaluated showed a negative relationship between pCO2 and Chl-a, which suggests that these water bodies show an autotrophic metabolism and behave as carbon dioxide- sink systems
Resumo:
Waste stabilization ponds are the main technology in use for domestic sewage treatment in Rio Grande do Norte State (RN), northeast Brazil. The are around 80 systems, constructed mainly by municipal city halls, being series comprised by a primary facultative pond followed by two maturation ponds the most used configuration. Due to problems related with the production and destination of sludge and generation of bad odors, the designers have avoided the use of anaerobic lagoons. The majority of systems are rarely monitored to verify their efficiencies and to get new project parameters for future designing. This work has as purpose to make a diagnosis of efficiency of three series of waste stabilization pond series (WSPS) of Jardim Lola 1, Jardim Lola 2 and Beira Rio, located in the North Zone of the city of the Natal/RN, treating domestic raw sewage, on the removal of organic matter and thermotolerant coliform, comparing the operational conditions of the systems this inside of the bands foreseen in the project, through parameters BOD5, QOD, thermotolerant coliforms, dissolved oxygen, pH, temperature, ammoniac nitrogen, total and suspended solids. The work was carried through in the WSPS, all constituted by a primary facultative pond followed by two maturation ponds. Socioeconomic characteristics of population are predominantly low and all the plants are very near of the contributing basins. The series were monitored from of May the November of 2002, totalizing 20 collections of grab samples of raw sewage and ponds effluents between 8:00 and 9:50 h. The main aspect to be detached by the results was the great concentration of organic matter (BOD and COD) and microorganisms the raw sewage which were around two times more concentrated than those values foreseen one in project. Considering all series the highest removals of organic matter were observed in system Beira Rio (84 and 78% of BOD and COD, respectively), which presented high hydraulic detention time (TDH = 89 days). On the other hand, Jardim Lola 1 and Jardim Lola 2 presented a much lower values of HDT (36 days and 18 days respectively) and their removals of BOD and COD were the same (76% and 60%, respectively). The Beira Rio WSPS, was the most efficient verified in relation to solids and ammonia, proving the great influence of the operational variables such as HDT and applied surface organic loadings on the performance of pond series. Although the treatment plants have reached efficiencies of thermotolerant coliforms around 99,999%, the concentrations in the final effluent can be considered very high for launching in aquatic bodies, particularly those produced by Jardim Lola 1 and Jardim Lola 2 series
Resumo:
The interdisciplinary nature of Astronomy makes it a field of great potential to explore various scientific concepts. However, studies show a great lack of understanding of fundamental subjects, including models that explain phenomena that mark everyday life, like the phases of the moon. Particularly in the context of distance education, learning of such models can be favored by the use of technologies of information and communication. Among other possibilities, we highlight the importance of digital materials that motivate and expand the forms of representation available about phenomena and models. It is also important, however, that these materials promote the explicitation of student's conceptions, as well as interaction with the most central aspects of the astronomical model for the phenomenon. In this dissertation we present a hypermedia module aimed at learning about the phases of the moon, drawn from an investigation on the difficulties with the subject during an Astronomy course for teaching training at undergraduate level at UFRN. The tests of three semesters of course were analyzed, taking into account also the alternative conceptions reported in the literature in astronomy education. The product makes use of small texts, questions, images and interactive animations. Emphasizes questions about the illumination of the Moon and other bodies, and their relationship to the sun, the perception from different angles of objects illuminated by a single source, the cause of the alternation between day and night, the identification of Moon's orbit around the Earth and the occurrence of the phases as a result of the position of observing it, and the perception of time involved in the phenomenon. The module incorporated considerations obtained from interviews with students in two poles where its given presential support for students of the course, and subjects from different pedagogical contexts. The final form of the material was used in a real situation of learning, as supplementary material for the final test of the discipline. The material was analyzed by 7 students and 4 tutors, among 56 users, in the period in question. Most students considered that the so called "Lunar Module" made a difference in their learning, the animations were considered the most prominent aspect, the images were indicated as stimulating and enlightening, and the text informative and enjoyable. The analysis of learning of these students, observing their responses to issues raised at the last evaluation, suggested gains in key aspects relating to the understanding of the phases, but also indicates more persistent difficulties. The work leads us to conclude that it is important to seek contributions for the training of science teachers making use of new technologies, with attention to the treatment of computer as a complementary resource. The interviews that preceded the use of the module, and the way student has sought the module if with questions and/or previous conflicts - established great difference in the effective contribution of the material, indicating that it should be used with the mediation of teacher or tutor, or via strategies that cause interactions between students. It is desirable that these interactions are associated with the recovery of memories of the subjects about previous observations and models, as well as the stimulus to new observations of phenomena
Resumo:
Macrófitas são importantes produtoras primárias do ecossistema aquático, e o desequilíbrio do ambiente pode ocasionar seu crescimento acelerado. Portanto, levantamentos de dados relacionados a macrófitas submersas são importantes para contribuir na gestão de corpos de água. Contudo, a amostragem dessa vegetação requer um enorme esforço físico. Nesse sentido, a técnica hidroacústica é apropriada para o estudo de macrófitas submersas. Assim, os objetivos deste trabalho foram avaliar os tipos de dados gerados pelo ecobatímetro e analisar como esses dados caracterizam a vegetação. Utilizou-se o ecobatímetro BioSonics DT-X acoplado a um GPS. A área de estudo é um trecho do Rio Uberaba, MG. A amostragem foi feita por meio de transectos, navegando de uma margem à outra. Depois de processar os dados, obteve-se informação a respeito de ocorrência de macrófitas submersas, profundidade, altura média das plantas, porcentagem da cobertura vegetal e posição. A partir desse conjunto de dados, foi possível extrair outras duas métricas: biovolume e altura efetiva do dossel. Os dados foram importados de um Sistema de Informação Geográfica e geraram-se mapas ilustrativos das variáveis estudadas. Além disso, quatro perfis foram selecionados para analisar a diferença entre as grandezas de representação de macrófitas. O ecobatímetro mostrou-se uma ferramenta eficaz no mapeamento de macrófitas submersas. Cada uma das medidas - altura do dossel, ECH ou biovolume - caracteriza de forma diferente a vegetação submersa. Dessa forma, a escolha do tipo de representação depende da aplicação desejada.
Resumo:
Physical Education establishes relations about sex-gender-sexuality by its programs. Thinking approaches among gender and sexuality questions from scholar Physical Education is a productive challenge. Inspired in post-structuralism studies, we problematized dialogues among body, gender, identity and body movement culture. Bodily our sports practices educate citizens beyond their performances, health and beauty. Their "truths" produce gender and sexuality brands in a culture process of branding differences. Cultural events are related in binary categories as good-bad, beautiful-ugly, thin-fat, similar-different, normal-unnatural, man-women, heterosexual-homosexual, that don't let to observe the multiplicity of people educate. We must to understand the pedagogical speeches about bodies as constituents of their own bloods.