Estudio del uso de triturado de palmera como sustrato de humedales de tratamiento de aguas residuales

[ES]Se ha hecho uso de un sustrato orgánico (triturado de palmera) en humedales artificiales para comprobar su idoneidad para el tratamiento de las aguas residuales, tanto en flujo vertical como horizontal y mixto, teniendo en cuenta la eficiencia de eliminación de los parámetros recogidos en la normativa y la posible obturación. Con este sustrato se consiguieron eliminaciones de entre el 80 y el 90% de materia orgánica, más del 98% de eliminación de sólidos en suspensión y turbidez y en torno al 99.9% de eliminación de coliformes fecales

Thermodynamics of aqueous biopolymer solutions and fractionation of Dextran

Flory-Huggins interaction parameters and thermal diffusion coefficients were measured for aqueous biopolymer solutions. Dextran (a water soluble polysaccharide) and bovine serum albumin (BSA, a water soluble protein) were used for this study. The former polymer is representative for chain macromolecules and the latter is for globular macromolecules. The interaction parameters for the systems water/dextran and water/BSA were determined as a function of composition by means of vapor pressure measurements, using a combination of headspace sampling and gas chromatography (HS-GC). A new theoretical approach, accounting for chain connectivity and conformational variability, describes the observed dependencies quantitatively for the system water/dextran and qualitatively for the system water/BSA. The phase diagrams of the ternary systems water/methanol/dextran and water/dextran/BSA were determined via cloud point measurements and modeled by means of the direct minimization of the Gibbs energy using the information on the binary subsystems as input parameters. The thermal diffusion of dextran was studied for aqueous solutions in the temperature range 15 < T < 55 oC. The effects of the addition of urea were also studied. In the absence of urea, the Soret coefficient ST changes its sign as T is varied; it is positive for T > 45.0 oC, but negative for T < 45.0 oC. The positive sign of ST means that the dextran molecules migrate towards the cold side of the fluid; this behavior is typical for polymer solutions. While a negative sign indicates the macromolecules move toward the hot side; this behavior has so far not been observed with any other binary aqueous polymer solutions. The addition of urea to the aqueous solution of dextran increases ST and reduces the inversion temperature. For 2 M urea, the change in the sign of ST is observed at T = 29.7 oC. At higher temperature ST is always positive in the studied temperature range. To rationalize these observations it is assumed that the addition of urea opens hydrogen bonds, similar to that induced by an increase in temperature. For a future extension of the thermodynamic studies to the effects of poly-dispersity, dextran was fractionated by means of a recently developed technique called Continuous Spin Fractionation (CSF). The solvent/precipitant/polymer system used for the thermodynamic studies served as the basis for the fractionation of dextran The starting polymer had a weight average molar mass Mw = 11.1 kg/mol and a molecular non-uniformity U= Mw / Mn -1= 1.0. Seventy grams of dextran were fractionated using water as the solvent and methanol as the precipitant. Five fractionation steps yielded four samples with Mw values between 4.36 and 18.2 kg/mol and U values ranging from 0.28 to 0.48.

Synthese, Tritierung, 99m Tc-Markierung und Evaluierung von Benzamid-Derivaten zur Visualisierung der D 2, D 3-Rezeptoren

Die Diagnose und Therapie von neurodegenerativen Krankheiten, wie beispielsweise Morbus Parkinson besitzt in der heutigen Gesellschaft eine immer größere Bedeutung. Über moderne, bild¬gebende nuklear¬medizinische Verfahren wie SPECT und PET ist es mit geeigneten Radioliganden möglich, Morbus Parkinson vor dem Auftreten von Symptomen zu diagnostizieren. Ein wichtiger Ansatzpunkt zur Diagnose von Morbus Parkinson ist die Visualisierung der postsynaptischen Dopamin-Rezeptoren über radioaktiv (11C, 18F, 123I) markierte Benz¬amid-Derivate. Auf Grundlage der (S)-Pyrolidin-2,3-dimethoxy-Benzamid-Struktur des 18F-Liganden Fallypride wurden verschiedene 99mTc-markierte Benzamid-Derivate als potentielle Radio¬liganden zur Parkinson-Diagnostik entwickelt. Um das Potential von Metall-konjugierten Benzamiden abschätzen zu können, wurden zunächst einfache Vergleichssubstanzen entwickelt. Diese sollten die Einführung eines Chelators simulieren und wurden hierfür hinsichtlich ihrer in vitro-Bindungsaffinitäten zu den Dopamin-, Serotonin- und adrenergen Rezeptoren evaluiert. Die zunächst entwickelten Derivate mit unterschiedlichen Kettenlängen zur Kopplung des Chelators zeigten für die Propylkette Affinitäten im nanomolaren Bereich. Im Anschluss sollten basierend auf diesen Ergebnissen vier verschiedene Chelatoren (Carbony-Cyclopentadienyl, Amido-Cyclopentadienyl, 2-Pyridyl-Imin und N2S2) über eine Propylkette an die 5-Position der Benzamidgrundstruktur gekoppelt werden. Die geplante Synthese des Carbonyl-Cyclopentadienyl-Derivates gelang jedoch nicht. Für die weiteren Chelatoren (Amido-Cyclopentadieny, 2-Pyridyl-Imin und N2S2) konnten die jeweiligen Markierungs¬vorläufer und Rhenium-Komplexe dargestellt werden, die ebenfalls hinsichtlich ihrer Bindungs¬affinitäten evaluiert wurden. Die erzielten Affinitäten zeigten, dass eine Über¬tragung der Affinitäten der einfachen Vergleichssubstanzen auf die komplexeren Metall-Benzamide nicht möglich war. Insbesondere der N2S2-Rhenium-Komplex besitzt nur noch geringe Affinität (490 - 900 nM) zu den D2- und D3-Rezeptoren. Die mittel-affinen 2-Pyridyl-Imin- und Amdio¬cyclopentadien-Komplexe wurden mit 99mTc markiert und die Markierungsausbeute hinsichtlich Reaktionstemperatur, Markierungs-vorläuferkonzentration und Heizmethoden optimiert. Dabei konnte der Imin-Komplex quantitativ mittels fac-[99mTc(CO)3(H2O)3]+ in 30 Minuten bei 45°C markiert werden. Der Amido-Cyclopentadien-Komplex konnte über die Umsetzung des Ferrocen-Markierungsvorläufer mit Mn(CO)5Br und [99mTcO4]- in Ausbeuten von bis zu 60 % markiert werden. Im Anschluss an die Markierungen wurden die 99mTc-Komplexe über HPLC isoliert und in in vitro-Auto¬radiographien von Rattenhirnschnitten weiter evaluiert. Die erhaltenen Ergebnisse bestätigten die für die Rhenium-Komplexe erzielten Affinitäten und zeigten keine spezifische Anreicherung in bestimmten Hirnarealen. Aus diesen Ergebnissen kann ge¬schlossen werden, dass die dargestellten 99mTc-Benzamide aufgrund mangelnder Affinitäten und einer hohen unspezifischen Bindung keine geeigneten Liganden zur Darstellung der D2- und D3- Rezeptoren sind. Um die dargestellten 99mTc-Benzamide mit [18F]Fallypride vergleichen zu können, wurde zusätzlich [3H]Fallypride dargestellt. Hierfür wurde zunächst der Nor-Markierungsvor¬läufer synthetisiert und die Markierungsausbeute optimiert. Die finale Umsetzung mit [3H]Methylnosylat ergab nach HPLC-Aufreinigung 15 mCi [3H]Fallypride mit einer radio¬chemischen Reinheit von >99,5 %. Erste Autoradiographien zeigten eine hohe Anreicherung des Liganden im Striatum, verbunden mit einer sehr niedrigen unspezifischen Bindung.

Control of fruit postharvest diseases by thermotherapy: understanding the mechanisms of action by –omics approaches

In recent years the hot water treatment (HW) represents an effective and safe approach for managing postharvest decay. This study reported the effect of an HW (60°C for 60 s and 45°C for 10 min) on brown rot and blue mould respectively. Peaches was found more thermotolerant compared to apple fruit, otherwise Penicillium expansum was more resistant to heat with respect to Monilinia spp. In semi-commercial and commercial trials, the inhibition of brown rot in naturally infected peaches was higher than 78% after 6 days at 0°C and 3 days at 20°C. Moreover, in laboratory trials a 100% disease incidence reduction was obtained by treating artificially infected peaches at 6-12 h after inoculation revealing a curative effect of HW. The expression levels of some genes were evaluated by qRT-PCR. Specifically, the cell wall genes (β-GAL, PL, PG, PME) showed a general decrease of expression level whereas PAL, CHI, HSP70 and ROS-scavenging genes were induced in treated peaches compared to the control ones. Contrarily, HW applied on artificially infected fruit before the inoculum was found to increase brown rot susceptibility. This aspect might be due to an increase of fruit VOCs emission as revealed by PTR-ToF-MS analysis. In addition a microarray experiment was conducted to analyze molecular mechanisms underneath the apple response to heat. Our results showed a largest amount of induced Heat shock proteins (HSPs), Heat shock cognate proteins (HSCs), Heat shock transcription factors (HSTFs) genes found at 1 and 4 hours from the treatment. Those genes required for the thermotolerance process could be involved in induced resistance response. The hypothesis was confirmed by 30% of blue mold disease reduction in artificially inoculated apple after 1 and 4 hours from the treatment. In order to improve peaches quality and disease management during storage, an innovative tool was also used: Da-meter.

Laboratory and field measurements of enantiomeric and non-enantiomeric biogenic VOCs and anthropogenic BTEX compounds

This doctoral thesis was focused on the investigation of enantiomeric and non-enantiomeric biogenic organic compound (BVOC) emissions from both leaf and canopy scales in different environments. In addition, the anthropogenic compounds benzene, toluene, ethylbenzene, and xylenes (BTEX) were studied. BVOCs are emitted into the lower troposphere in large quantities (ca. 1150 Tg C ·yr-1), approximately an order of magnitude greater than the anthropogenic VOCs. BVOCs are particularly important in tropospheric chemistry because of their impact on ozone production and secondary organic aerosol formation or growth. The BVOCs examined in this study were: isoprene, (-)/ (+)-α-pinene, (-)/ (+)-ß-pinene, Δ-3-carene, (-)/ (+)-limonene, myrcene, eucalyptol and camphor, as these were the most abundant BVOCs observed both in the leaf cuvette study and the ambient measurements. In the laboratory cuvette studies, the sensitivity of enantiomeric enrichment change from the leaf emission has been examined as a function of light (0-1600 PAR) and temperature (20-45°C). Three typical Mediterranean plant species (Quercus ilex L., Rosmarinus officinalis L., Pinus halepensis Mill.) with more than three individuals of each have been investigated using a dynamic enclosure cuvette. The terpenoid compound emission rates were found to be directly linked to either light and temperature (e.g. Quercus ilex L.) or mainly to temperature (e.g. Rosmarinus officinalis L., Pinus halepensis Mill.). However, the enantiomeric signature showed no clear trend in response to either the light or temperature; moreover a large variation of enantiomeric enrichment was found during the experiment. This enantiomeric signature was also used to distinguish chemotypes beyond the normal achiral chemical composition method. The results of nineteen Quercus ilex L. individuals, screened under standard conditions (30°C and 1000 PAR) showed four different chemotypes, whereas the traditional classification showed only two. An enclosure branch cuvette set-up was applied in the natural boreal forest environment from four chemotypes of Scots pine (Pinus sylvestris) and one chemotype of Norway spruce (Picea abies) and the direct emissions compared with ambient air measurements above the canopy during the HUMPPA-COPEC 2010 summer campaign. The chirality of a-pinene was dominated by (+)-enantiomers from Scots pine while for Norway spruce the chirality was found to be opposite (i.e. Abstract II (-)-enantiomer enriched) becoming increasingly enriched in the (-)-enantiomer with light. Field measurements over a Spanish stone pine forest were performed to examine the extent of seasonal changes in enantiomeric enrichment (DOMINO 2008). These showed clear differences in chirality of monoterpene emissions. In wintertime the monoterpene (-)-a-pinene was found to be in slight enantiomeric excess over (+)-a-pinene at night but by day the measured ratio was closer to one i.e. racemic. Samples taken the following summer in the same location showed much higher monoterpene mixing ratios and revealed a strong enantiomeric excess of (-)-a-pinene. This indicated a strong seasonal variance in the enantiomeric emission ratio which was not manifested in the day/night temperature cycles in wintertime. A clear diurnal cycle of enantiomeric enrichment in a-pinene was also found over a French oak forest and the boreal forest. However, while in the boreal forest (-)-a-pinene enrichment increased around the time of maximum light and temperature, the French forest showed the opposite tendency with (+)-a-pinene being favored. For the two field campaigns (DOMINO 2008 and HUMPPA-COPEC 2010), the BTEX were also investigated. For the DOMINO campaign, mixing ratios of the xylene isomers (meta- and para-) and ethylbenzene, which are all well resolved on the ß-cyclodextrin column, were exploited to estimate average OH radical exposures to VOCs from the Huelva industrial area. These were compared to empirical estimates of OH based on JNO2 measured at the site. The deficiencies of each estimation method are discussed. For HUMPPA-COPEC campaign, benzene and toluene mixing ratios can clearly define the air mass influenced by the biomass burning pollution plume from Russia.

Development of a biorefinery scheme for the valorization of olive mill wastewaters and grape pomaces

In the Mediterranean area, olive mill wastewater (OMW) and grape pomace (GP) are among the major agro-industrial wastes produced. These two wastes have a high organic load and high phytotoxicity. Thus, their disposal in the environment can lead to negative effects. Second-generation biorefineries are dedicated to the valorization of biowaste by the production of goods from such residual biomasses. This approach can combine bioremediation approaches to the generation of noble molecules, biomaterials and energy. The main aim of this thesis work was to study the anaerobic digestion of OMW and GP under different operational conditions to produce volatile fatti acids (VFAs) (first stage aim) and CH4 (second stage aim). To this end, a packed-bed biofilm reactor (PBBR) was set up to perform the anaerobic acidogenic digestion of the liquid dephenolized stream of OMW (OMWdeph). In parallel, the solid stream of OMW (OMWsolid), previously separated in order to allow the solid phase extraction of polyphenols, was addressed to anaerobic methanogenic digestion to obtain CH4. The latter experiment was performed in 100ml Pyrex bottles which were maintained at different temperatures (55-45-37°C). Together with previous experiments, the anaerobic acidogenic digestion of fermented GP (GPfreshacid) and dephenolized and fermented GP (GPdephacid) was performed in 100ml Pyrex bottles to estimate the concentration of VFAs achievable from each aforementioned GPs. Finally, the same matrices of GP and not pre-treated GP (GPfresh) were digested under anaerobic methanogenic condition to produce CH4. Anaerobic acidogenic and methanogenic digestion processes of GPs lasted about 33 days. Instead, the anaerobic acidogenic and methanogenic digestion process of OMWs lasted about 121 and 60 days, respectively. Each experiment was periodically monitored by analysing volume and composition of produced biogas and VFA concentration. Results showed that VFAs were produced in higher concentrations in GP compared to OMWdeph. The overall concentration of VFAs from GPfreshacid was approximately 39.5 gCOD L-1, 29 gCOD L-1 from GPdephacid, and 8.7 gCOD L-1 from OMWdeph. Concerning the CH4 production, the OMWsolid reached a high biochemical methane potential (BMP) at a thermophilic temperature (55°) than at mesophlic ones (37-45°C). The value reached was about 358.7 mlCH4 gSVsub-1. In contrast, GPfresh got a high BMP but at a mesophilic temperature. The BMP was about 207.3 mlCH4 gSVsub-1, followed by GPfreshacid with about 192.6 mlCH4 gSVsub-1 and lastly GPdephacid with about 102.2 mlCH4 gSVsub-1. In summary, based on the gathered results, GP seems to be a better carbon source for acidogenic and methanogenic microrganism compared to OMW, because higher amount of VFAs and CH4 were produced in AD of GP than OMW. In addition to these products, polyphenols were extracted by means of a solid phase extraction (SPE) procedure by another research group, and VFAs were utilised for biopolymers production, in particular polyhydroxyalkanoates (PHAs), by the same research group in which I was involved.

Ottimizzazione del processo di sintesi di microcapsule melammina-formaldeide

Lo scopo di questo elaborato di tesi è sintetizzare microcapsule di dimensioni non superiori ai 20 micron, contenenti un composto termocromico in modo da funzionare come indicatori di temperatura. Le capsule devono essere quindi in grado di variare la propria colorazione in funzione della temperatura del mezzo in cui sono disperse o dell’ambiente circostante, senza degradarsi. Il core è costituito da una miscela contenente un pigmento termocromico il cui colore varia da verde intenso se mantenuto a temperature ambiente, fino ad un verde pallido, quasi bianco, per temperature inferiori ai 10°C. Il core è stato quindi incapsulato in uno shell, costituito da una resina melammina-formaldeide (MF) mediante polimerizzazione in situ. Questo processo prevede la sintesi di un prepolimero MF che viene poi fatto reticolare in presenza di una emulsione del core in soluzione acquosa. Per prima cosa è stato ottimizzata la sintesi del prepolimero a partire da una soluzione acquosa di melammina e formaldeide. Vista la tossicità della formaldeide (H341-H350-H370) è stata studiata anche la possibilità di sostituire questo reagente con la sua forma polimerica (paraformaldeide) che a 45°C circa degrada rilasciando formaldeide in situ. In questo modo il processo risulta molto più sicuro anche in previsione di un suo possibile sviluppo industriale. In seguito è stato ottimizzato il processo di microincapsulazione in emulsione su vari tipi di core e studiando l’effetto di vari parametri (pH, temperatura, rapporto core/shell, tipo di emulsionante ecc.), sulle dimensioni e la stabilità delle microcapsule finali. Queste sono quindi state caratterizzate mediante spettrometria Infrarossa in trasformata di Fourier (FT-IR) e la loro stabilità termica è stata controllata tramite analisi TermoGravimetrica (TGA). Il processo di reticolazione (curing) della resina, invece, è stato studiato tramite Calorimetria Differenziale a Scansione (DSC). Le microcapsule sono inoltre state analizzate tramite Microscopio Elettronico (OM) e Microscopio Elettronico a Scansione (SEM).

Diagenesis of a light, tight-oil chert reservoir at the Ediacaran/Cambrian boundary, Sultanate of Oman

The Al Shomou Silicilyte Member (Athel Formation) in the South Oman Salt Basin shares many of the characteristics of a light, tight-oil (LTO) reservoir: it is a prolifi c source rock mature for light oil, it produces light oil from a very tight matrix and reservoir, and hydraulic fracking technology is required to produce the oil. What is intriguing about the Al Shomou Silicilyte, and different from other LTO reservoirs, is its position related to the Precambrian/Cambrian Boundary (PCB) and the fact that it is a ‘laminated chert‘ rather than a shale. In an integrated diagenetic study we applied microstructural analyses (SEM, BSE) combined with state-of-the-art stable isotope and trace element analysis of the silicilyte matrix and fractures. Fluid inclusion microthermometry was applied to record the salinity and minimum trapping temperatures. The microstructural investigations reveal a fi ne lamination of the silicilyte matrix with a mean lamina thickness of ca. 20 μm consisting of predominantly organic matter-rich and fi nely crystalline quartz-rich layers, respectively. Authigenic, micron-sized idiomorphic quartz crystals are the main matrix components of the silicilyte. Other diagenetic phases are pyrite, apatite, dolomite, magnesite and barite cements. Porosity values based on neutron density logs and core plug data indicate porosity in the silicilyte ranges from less than 2% to almost to 40%. The majority of the pore space in the silicilyte is related to (primary) inter-crystalline pores, with locally important oversized secondary pores. Pore casts of the silica matrix show that pores are extremely irregular in three dimensions, and are generally interconnected by a complex web or meshwork of fi ne elongate pore throats. Mercury injection capillary data are in line with the microstructural observations suggesting two populations of pore throats, with an effective average modal diameter of 0.4 μm. The acquired geochemical data support the interpretation that the primary source of the silica is the ambient seawater rather than hydrothermal or biogenic. A maximum temperature of ca. 45°C for the formation of microcrystalline quartz in the silicilyte is good evidence that the lithifi cation and crystallization of quartz occurred in the fi rst 5 Ma after deposition. Several phases of brittle fracturing and mineralization occurred in response to salt tectonics during burial. The sequences of fracture-fi lling mineral phases (dolomite - layered chalcedony – quartz – apatite - magnesite I+II - barite – halite) indicates a complex fl uid evolution after silicilyte lithifi cation. Primary, all-liquid fl uid inclusions in the fracturefi lling quartz are good evidence of growth beginning at low temperatures, i.e. ≤ 50ºC. Continuous precipitation during increasing temperature and burial is documented by primary two-phase fl uid inclusions in quartz cements that show brines at 50°C and fi rst hydrocarbons at ca. 70°C. The absolute timing of each mineral phase can be constrained based on U-Pb geochronometry, and basin modelling. Secondary fl uid inclusions in quartz, magnesite and barite indicate reactivation of the fracture system after peak burial temperature during the major cooling event, i.e. uplift, between 450 and 310 Ma. A number of fi rst-order trends in porosity and reservoir-quality distribution are observed which are strongly related to the diagenetic and fl uid history of the reservoir: the early in-situ generation of hydrocarbons and overpressure development arrests diagenesis and preserves matrix porosity. Chemical compaction by pressure dissolution in the fl ank areas could be a valid hypothesis to explain the porosity variations in the silicilitye slabs resulting in lower porosity and poorer connectivity on the fl anks of the reservoir. Most of the hydrocarbon storage and production comes from intervals characterized by Amthor et al. 114488 preserved micropores, not hydrocarbon storage in a fracture system. The absence of oil expulsion results in present-day high oil saturations. The main diagenetic modifi cations of the silicilyte occurred and were completed relatively early in its history, i.e. before 300 Ma. An instrumental factor for preserving matrix porosity is the diffi culty for a given slab to evacuate all the fl uids (water and hydrocarbons), or in other words, the very good sealing capacity of the salt embedding the slab.

Calidad del agua en el área regadía del Río Mendoza (Argentina)

El río Mendoza conforma el oasis norte que es el más importante de la provincia. El crecimiento urbano ha avanzado sobre áreas originalmente agrícolas, rodeando la red de canales y desagües, que también recibe los desagües pluviales urbanos, producto de tormentas convectivas. La actividad antropogénica utiliza el recurso para bebida, saneamiento, riego, recreación, etc., y vuelca sus excedentes a la red, contaminándola. Para conocer la calidad del agua de esta cuenca se seleccionaron, estratégicamente, 15 sitios de muestreo: 3 a lo largo del río y a partir del dique derivador Cipolletti (R_I a R_III), 5 en la red de canales (C_I a C_V) y 7 ubicados en los colectores de drenaje (D_I a D_VII). Se realizaron los siguientes análisis físico-químicos y microbiológicos; en el río y en la red de canales: conductividad eléctrica, temperatura, pH, aniones y cationes (cálculo de RAS), oxígeno disuelto (OD), sólidos sedimentables, demanda química de oxígeno (DQO), bacterias aerobias mesófilas (BAM), coliformes totales y fecales y metales pesados. En la red de drenaje sólo se realizaron los cuatro primeros. Los resultados de los análisis, se incorporaron a una base de datos y se sometieron a un análisis estadístico descriptivo e inferencial. Este último consistió en la aplicación de diversas pruebas en busca de posibles diferencias entre los sitios de muestreo, para cada variable respuesta, a un α = 0.05. Se realizó el análisis de la varianza de efectos fijos y de efectos aleatorios y se probaron los supuestos de homocedasticidad y de normalidad de los errores. En el caso de violación de los supuestos, se utilizó la prueba de Kruskal- Wallis. Se compararon los siguientes sitios de muestreo entre sí: ríos, R_I-canales y drenajes. Se concluyó que hay un aumento significativo de la salinidad y la sodicidad en R_II, que los cambios de calidad ocurridos entre R_II y R_III podrían deberse al aporte de otras aguas. Con respecto a la comparación de los parámetros entre la cabeza del sistema (R_I) y la red de canales se puede decir que los aportes realizados por los escurrimientos urbanos ubicados hacia el oeste del canal Cacique Guaymallén, sumados a los vuelcos de Campo Espejo (detectados en C_II), incrementan significativamente la salinidad (+55 %) y sodicidad del agua (+95 %) respecto del punto R_I, aunque el valor de sodicidad sigue siendo bajo. También se han encontrado incrementos de salinidad (+80 %), de DQO (+1159 %) y BAM (+2873 %) con lógica disminución de OD (-58 %) en el punto C_V (canal Auxiliar Tulumaya) respecto del punto R_I, ocasionados por aportes urbanos (Gran Mendoza) sumados a la carga contaminante del canal Pescara. Los metales pesados no presentan grandes diferencias entre sitios de muestreo.

Research lines in Hyperthermia at the Bioinstrumentation Laboratory of the Centre for Biomedical Technology

The Bioinstrumentation Laboratory belongs to the Centre for Biomedical Technology (CTB) of the Technical University of Madrid and its main objective is to provide the scientific community with devices and techniques for the characterization of micro and nanostructures and consequently finding their best biomedical applications. Hyperthermia (greek word for “overheating”) is defined as the phenomenon that occurs when a body is exposed to an energy generating source that can produce a rise in temperature (42-45ºC) for a given time [1]. Specifically, the aim of the hyperthermia methods used in The Bioinstrumentation Laboratory is the development of thermal therapies, some of these using different kinds of nanoparticles, to kill cancer cells and reduce the damage on healthy tissues. The optical hyperthermia is based on noble metal nanoparticles and laser irradiation. This kind of nanoparticles has an immense potential associated to the development of therapies for cancer on account of their Surface Plasmon Resonance (SPR) enhanced light scattering and absorption. In a short period of time, the absorbed light is converted into localized heat, so we can take advantage of these characteristics to heat up tumor cells in order to obtain the cellular death [2]. In this case, the laboratory has an optical hyperthermia device based on a continuous wave laser used to kill glioblastoma cell lines (1321N1) in the presence of gold nanorods (Figure 1a). The wavelength of the laser light is 808 nm because the penetration of the light in the tissue is deeper in the Near Infrared Region. The first optical hyperthermia results show that the laser irradiation produces cellular death in the experimental samples of glioblastoma cell lines using gold nanorods but is not able to decrease the cellular viability of cancer cells in samples without the suitable nanorods (Figure 1b) [3]. The generation of magnetic hyperthermia is performed through changes of the magnetic induction in magnetic nanoparticles (MNPs) that are embedded in viscous medium. The Figure 2 shows a schematic design of the AC induction hyperthermia device in magnetic fluids. The equipment has been manufactured at The Bioinstrumentation Laboratory. The first block implies two steps: the signal selection with frequency manipulation option from 9 KHz to 2MHz, and a linear output up to 1500W. The second block is where magnetic field is generated ( 5mm, 10 turns). Finally, the third block is a software control where the user can establish initial parameters, and also shows the temperature response of MNPs due to the magnetic field applied [4-8]. The Bioinstrumentation Laboratory in collaboration with the Mexican company MRI-DT have recently implemented a new research line on Nuclear Magnetic Resonance Hyperthermia, which is sustained on the patent US 7,423,429B2 owned by this company. This investigation is based on the use of clinical MRI equipment not only for diagnosis but for therapy [9]. This idea consists of two main facts: Magnetic Resonance Imaging can cause focal heating [10], and the differentiation in resonant frequency between healthy and cancer cells [11]. To produce only heating in cancer cells when the whole body is irradiated, it is necessary to determine the specific resonant frequency of the target, using the information contained in the spectra of the area of interest. Then, special RF pulse sequence is applied to produce fast excitation and relaxation mechanism that generates temperature increase of the tumor, causing cellular death or metabolism malfunction that stops cellular division

Investigación técnica y económica sobre desinfección de aguas residuales por sistemas de oxidación

Un incremento de la demanda del agua, junto con el aumento de la contaminación, ha provocado que hoy en día la reutilización de las aguas depuradas sea necesaria, pero la reutilización de aguas debe garantizar y minimizar los posibles riesgos sanitarios y medioambientales que su práctica pueda provocar. En España estos parámetros se encuentran regulados por el RD 1620/2007 relativo al régimen jurídico de la reutilización de las aguas depuradas. Las aguas regeneradas son aguas que ya han sido sometidas a un tratamiento de depuración, y a las cuales se aplica un posterior tratamiento adicional o complementario que permita adecuar su calidad al uso al que vaya a destinarse. Siendo requeridos para los distintos reúsos procesos de desinfección, uno de los principales sistemas utilizados es el cloro, debido a su sencilla aplicación y costos bajos, sin tomar en cuenta la posible formación de compuestos organohalogenados potencialmente cancerígenos. Es por esto que surge la necesidad de aplicar distintos sistemas de oxidación objeto de estudio en esta tesis, como el dióxido de cloro estabilizado, ozono y los procesos avanzados de oxidación (Advanced Oxidation Processes, AOP), ozono/peróxido y uv/peróxido. En esta tesis se investiga los rendimientos que pueden alcanzar estos sistemas en la eliminación de los ácidos húmicos y los fenoles, siendo las principales sustancias formadoras de subproductos de la desinfección, así mismo, se considera necesario garantizar la desinfección del agua a través del estudio de tres grupos de microrganismos, los coliformes totales, e. coli y enterococos, siendo un punto importante el posible recrecimiento microbiológico debido a una desinfección escasa, por la permanencia en el agua de los compuestos antes mencionados, o por alguna fuente de alimento que pudieran encontrar en el sistema de distribución. Lo más importante será la calidad que se pueda alcanzar con estos desinfectantes, con el fin de obtener agua para los distintos reúsos que existen en la actualidad. Y así no limitar los alcances que puede tener la reutilización de las aguas residuales. Basándose en lo antes mencionado se procedió a realizar la caracterización del agua del rio Manzanares, con el fin de determinar la cantidad de ácidos húmicos disueltos y fenoles, obteniendo valores bajos, se decidió incorporar a las muestras de rio 5 mg/L de estos compuestos, con el fin de observar de que manera podrían interferir en la desinfección de esta agua. De esta forma se logran obtener resultados óptimos de los sistemas de desinfección estudiados, siendo el Ozono un oxidante eficiente en la desinfección de los microrganismos y en la eliminación de ácidos húmicos y fenoles con tiempos de contacto cortos, mostrando deficiencias al permitir el recrecimiento de los coliformes totales. Del sistema de oxidación avanzada UV/Peróxido se determino como un eficiente desinfectante para garantizar la inexistencia de rebrotes, al paso del tiempo. Así mismo se concluye que tiene buenos rendimientos en la eliminación del ácido húmico y los fenoles. An increase in water demand, coupled with increasing pollution, has caused today reuse of treated water is necessary, but must ensure water reuse and minimize potential health and environmental risks that their practice is cause. In Spain these parameters are regulated by Royal Decree 1620/2007 on the legal regime of the reuse of treated water. The reclaimed water is water that has already been subjected to a depuration treatment, which is applied as a subsequent further treatment that will bring quality to the use to which is to be delivered. As required for various reuses disinfection processes, one of the main systems used is chlorine, due to its simple implementation and low costs, without taking into account the possible formation of potentially carcinogenic halogenated organic compounds. That is why there is a need to apply different oxidation systems studied in this thesis, as stabilized chlorine dioxide, ozone and advanced oxidation processes (AOP), ozone/peroxide and UV/peroxide. This thesis investigates the rates can reach these systems in removing humic acids and phenols, the main substances forming disinfection byproducts, likewise, it is considered necessary to ensure water disinfection through the study of three groups of microorganisms, total coliform, e. coli and enterococci, the important point being a possible regrowth due to microbiological disinfection scarce, the water remaining on the aforementioned compounds, or a food source which may be found in the distribution system. The most important quality is that achievable with these disinfectants, with the water to obtain various reuses that exist today. And thus not limit the scope that can be reuse of wastewater. Based on the above we proceeded to perform characterization Manzanares river water, in order to determine the quantity of dissolved humic acids and phenols, obtaining low values, it was decided to incorporate river samples 5 mg / L of these compounds, in order to observe how they might interfere with the disinfection of the water. Thus optimum results are achieved for disinfection systems studied, being efficient ozone oxidant in the disinfection of microorganisms and the removal of humic acids and phenols with short contact times, showing gaps to allow regrowth total coliforms. Advanced oxidation system UV / peroxide were determined as an efficient disinfectant to ensure the absence of volunteers, the passage of time. Also it is concluded that has good yields in removing humic acid and phenols.

Estudio de la calidad del agua en cisternas de captación de agua de lluvia en escuelas rurales de Alagoas (Brasil)

El presente trabajo se centra en el estudio de la calidad del agua de Sistemas de Recogida de agua de lluvia en escuelas del Semiárido Alagoano de Brasil. Aspectos de la obra civil también son incluidos. Los Sistemas principalmente están formados por un área de captación de agua de lluvia, cisternas de placas de cemento, canalizaciones que las unen y una bomba manual para la retirada del agua de la cisterna. Se analizaron 206 muestras de parámetros básicos de la calidad del agua – conductividad eléctrica, turbidez, pH, cloro residual y colifomes fecales- en 15 cisternas escolares, 3 comunitarias y 2 domiciliarias durante 5 meses. Las propiedades físico-químicas mostraron casi siempre valores acordes con la legislación brasileña (PORTARIA Nº 518/2004), aunque en algunos casos se encontraron pH alcalinos causados por el cemento de la cisterna que disminuyen la eficacia de la cloración, único tratamiento empleado en la zona. Por otra parte, los análisis en mini laboratorio de coliformes fecales resultaron positivos en un 27% de las veces, siendo inadecuado para el consumo humano según la normativa del país. Sin embargo, cuando se desviaban las primeras lluvias contenientes de contaminantes del tejado, las bacterias disminuían casi por completo. Se ha recomendado por lo tanto, además de otros aspectos, la utilización de dispositivos automáticos y de bajo coste para la retirada de las primeras aguas. Otras influencias en la calidad del agua también fueron halladas.

Optimización de la aplicación de lodos de depuración de aguas residuales al abonado o mejora de suelos

El objetivo de este trabajo de investigación fue evaluar el efecto de la aplicación de lodos residuales procedentes de una planta de tratamiento de aguas residuales acondicionados como biosólido para el abonado de tres cultivos agrícolas. Esto se realizó a través del estudio de las variables de producción (desarrollo vegetal de cada cultivo) y de la comparación de las características de los suelos utilizados antes y después de los ensayos experimentales. A través de la investigación se confirmó la mejora en la calidad del suelo y mejor rendimiento de cultivo debido a los biosólidos procedentes de tratamiento de aguas residuales. Este trabajo de investigación de tipo descriptivo y experimental, utilizó lodos optimizados que fueron aplicados a tres cultivos agrícolas de ciclo corto. Fueron evaluados dos cultivos (sandía y tomate) bajo riego y un cultivo (arroz) en secano. En la primera fase del trabajo se realizó la caracterización de los lodos, para ellos se realizaron pruebas físico químicas y microbiológicas. Fue utilizado el método de determinación de metales por espectrometría de emisión atómica de plasma acoplado inductivamente, (ICP-AES) para conocer las concentraciones de metales. La caracterización microbiológica para coliformes totales y fecales se realizó utilizando la técnica del Número más probable (NMP), y para la identificación de organismos patógenos se utilizó el método microbiológico propuesto por Kornacki & Johnson (2001), que se fundamenta en dos procesos: pruebas presuntivas y prueba confirmativa. Tanto los resultados para la determinación de metales y elementos potencialmente tóxicos; como las pruebas para la determinación de microorganismos potencialmente peligrosos, estuvieron por debajo de los límites considerados peligrosos establecidos por la normativa vigente en Panama (Reglamento Técnico COPANIT 47-2000). Una vez establecido la caracterización de los lodos, se evalúo el potencial de nutrientes (macro y micro) presentes en los biosólidos para su potencial de uso como abono en cultivos agrícolas. El secado de lodos fue realizado a través de una era de secado, donde los lodos fueron deshidratados hasta alcanzar una textura pastosa. “La pasta de lodo” fue transportada al área de los ensayos de campo para continuar el proceso de secado y molida. Tres ensayos experimentales fueron diseñados al azar con cinco tratamientos y cuatro repeticiones para cada uno de los tres cultivos: sandía, tomate, arroz, en parcelas de 10m2 (sandía y tomate) y 20 m2 (arroz) para cada tratamiento. Tres diferentes dosis de biosólidos fueron evaluadas y comparadas con un tratamiento de fertilizante comercial y un tratamiento control. La dosis de fertilizante comercial utilizada en cada cultivo fue la recomendada por el Instituto de Investigación Agropecuaria de Panamá. Los ensayos consideraron la caracterización inicial del suelo, la preparación del suelo, semilla, y arreglo topográfico de los cultivos siguiendo las recomendaciones agronómicas de manejo de cultivo establecida por el Instituto de Investigación Agropecuaria. Para los ensayos de sandía y tomate se instaló el sistema de riego por goteo. Se determinaron los ácidos húmicos presentes en los cultivos, y se estudiaron las variables de desarrollo de cada cultivo (fructificación, cosecha, peso de la cosecha, dimensiones de tamaño y color de las frutas, rendimiento, y la relación costo – rendimiento). También se estudiaron las variaciones de los macro y micro nutrientes y las variaciones de pH, textura de suelo y MO disponible al inicio y al final de cada uno de los ensayos de campo. Todas las variables y covariables fueron analizadas utilizando el programa estadístico INFOSAT (software para análisis estadístico de aplicación general) mediante el análisis de varianza, el método de comparaciones múltiples propuesto por Fisher (LSD Fisher) para comparar las medias de los cultivares y el coeficiente de correlación de Pearson que nos permite analizar si existe una asociación lineal entre dos variables. En la evaluación de los aportes del biosólido a los cultivos se observó que los macronutrientes N y P se encontraban de los límites requeridos en cada uno de los cultivos, pero que los niveles de K estuvieron por debajo de los requerimientos de los cultivos. A nivel de la fertilización tradicional con fertilizante químico se observó que la dosis recomendada para cada uno de los cultivos del estudio estaba sobreestimada en los tres principales macronutrientes: Nitrógeno, Fosforo y Potasio. Contenían concentraciones superiores de N, P y K a las requeridas teóricamente por el cultivo. El nutriente que se aporta en exceso es el Fósforo. Encontramos que para el cultivo de sandía era 18 veces mayor a lo requerido por el cultivo, en tomate fue 12 veces mayor y en el cultivo de arroz, 34 veces mayor. El fertilizante comercial tuvo una influencia en el peso final y rendimiento final en cada uno de los cultivos del estudio. A diferencia, los biosólidos tuvieron una influencia directa en el desarrollo de los cultivos (germinación, coloración, tamaño, longitud, diámetro, floración y resistencia a enfermedades). Para el caso de la sandía la dosis de biosólido más cercana al óptimo para el cultivo es la mayor dosis aplicada en este ensayo (97.2 gramos de biosólido por planta). En el caso de tomate, el fertilizante comercial obtuvo los mejores valores, pero las diferencias son mínimas con relación al tratamiento T1, de menor dosis de biosólido (16.2 gramos de biosólido por planta). Los resultados generales del ensayo de tomate estuvieron por debajo del rendimiento esperado para el cultivo. Los tratamientos de aplicación de biosólidos aportaron al desarrollo del cultivo en las variables tamaño, color y resistencia a las enfermedades dentro del cultivo de tomate. Al igual que el tomate, en el caso del arroz, el tratamiento comercial obtuvo los mejores resultados. Los resultados finales de peso y rendimiento del cultivo indican que el tratamiento (T2), menor dosis de biosólido (32.4 gramos por parcela), no tuvo diferencias significativas con los resultados obtenidos en las parcelas con aplicación de fertilizante comercial (T1). El tratamiento T4 (mayor dosis de biosólido) obtuvo los mejores valores para las variables germinación, ahijamiento y espigamiento del cultivo, pero al momento de la maduración obtuvo los menores resultados. Los biosólidos aportan nutrientes a los cultivos y al final del ensayo se observó que permanecen disponibles en el suelo, aportando a la mejora del suelo final. En los tres ensayos, se pudo comprobar que los aportes de los biosólidos en el desarrollo vegetativo de los cultivos. También se encontró en todos los ensayos que no hubo diferencias significativas (p > 0.05) entre los tratamientos de biosólidos y fertilizante comercial. Para obtener mejores resultados en estos tres ensayos se requeriría que a la composición de biosólidos (utilizada en este ensayo) se le adicione Potasio, Calcio y Magnesio en las cantidades requeridas por cada uno de los cultivos. ABSTRACT The objective of this investigation was to evaluate the effect of residual sewage sludge obtained from the residual water of a treatment plant conditioned as Biosolid used on three reliable agricultural crops. The effect of the added sewage sludge was evaluated through the measurement of production variables such as crop plant development and the comparison of the soil characteristics used before and after the experimental tests. This investigation confirmed that biosolids from wastewater treatment can contribute to the growth of these crops. In this experimental approach, optimized sludge was applied to three short-cycle crops including two low-risk crops (watermelon and tomato) and one high-risk crop (rice) all grown on dry land. In the first phase of work, the characteristics of the sludge were assessed using chemical, physical and microbiological tests. The concentrations of metals were determined by atomic emission spectrometry inductively coupled plasma, (ICP-AES). Microbiological characterization was performed measuring total coliform and fecal count using the most probable number technique (NMP) and microbiological pathogens were identified using Kornacki & Johnson (2001) method based on two processes: presumptive and confirmatory tests. Both the results for the determination of metals and potentially toxic elements, as testing for the determination of potentially dangerous microorganisms were below the limits established by the applicable standard in Panama (Technical Regulate COPANIT 47-2000). After the metal and bacterial characterization of the sludge, the presence of macro or micronutrients in biosolids was measured to evaluate its potential for use as fertilizer in the growth of agricultural crops. The sludge was dehydrated via a drying process into a muddy slurry. The pulp slurry was transported to the field trial area to continue the process of drying and grinding. Three randomized experimental trials were designed to test with five treatment regimens and four replications for each of the crops: watermelon, tomato, rice. The five treatment regimens evaluated were three different doses of bio solid with commercial fertilizer treatment control and no fertilizer treatment control. Treatment areas for the watermelon and tomato were 10m2 plots land and for rice was 20m2. The amount of commercial fertilizer used to treat each crop was based on the amount recommended by Agricultural Research Institute of Panama. The experimental trials considered initial characterization of soil, soil preparation, seed, and crop topographical arrangement following agronomic crop management recommendations. For the tests evaluating the growth of watermelons and tomatoes and drip irrigation system was installed. The amount of humic acids present in the culture were determined and developmental variable of each crop were studied (fruiting crop harvest weight, size dimensions and color of the fruit, performance and cost effectiveness). Changes in macro and micronutrients and changes in pH, soil texture and OM available were measured at the beginning and end of each field trial. All variables and covariates were analyzed using INFOSAT statistical program (software for statistical analysis of general application) by analysis of variance, multiple comparisons method as proposed by Fisher (LSD Fisher) to compare the means of cultivars and the Pearson ratio that allows us to analyze if there is a linear association between two variables. In evaluating the contribution of biosolids to agricultural crops, the study determined that the macronutrients N & P were within the requirements of crops, but K levels were below the requirements of crops. In terms of traditional chemical fertilizer fertilization, we observed that the recommended dose for each study crop was overestimated for the three major nutrients: nitrogen, phosphorus and potassium. Higher concentrations containing N, P and K to the theoretically required by the crop. The recommended dose of commercial fertilizer for crops study contained greater amounts of phosphorus, crops that need. The level of phosphorous was found to be18 times greater than was required for the cultivation of watermelon; 12 times higher than required for tomato, and 34 times higher than required for rice cultivation. Phosphorus inputs of commercial fertilizer were a primary influence on the weight and performance of each crop. Unlike biosolids had a direct influence on crop development (germination, color, size, length, diameter, flowering and disease resistance). In the case of growth of watermelons, the Biosolid dose closest to the optimum for cultivation was applied the highest dose in this assay (97.2 grams of bio solids per plant). In the case of tomatoes, commercial fertilizer had the best values but the differences were minimal when compared to treatment T1, the lower dose of sewage sludge (Biosolid 16.2 grams per plant). The overall results for the tomato crop yield of the trial were lower than expected. Additionally, the application of biosolids treatment contributed to the development of fruit of variable size, color and disease resistance in the tomato crops. Similar to the tomato crop, commercial fertilizer treatment provided the best results for the rice crop. The final results of weight and crop yield for rice indicated that treatment with T2 amount of biosolids (34.2 grams per plot) was not significantly different from the result obtained in the application plot given commercial fertilizer (T1). The T4 (higher dose of bio solid) treatment had the best values for the germination, tillering and bolting variables of the rice crop but for fruit ripening yielded lower results. In all three trials, biosolids demonstrated the ability to contribute in the vegetative growth of crops. It was also found in all test no significant differences (p>0.05) between treatment of bio solid and commercial fertilizer. Biosolids provided nutrients to the crops and even at the end of the trial remained available in the ground soil, contributing to the improvement of the final ground. The best results from these three trials is that the use of bio solids such as those used in this assay would require the addition of potassium, calcium and magnesium in quantities required for each crop.

Hybridization of single-stranded DNA targets to immobilized complementary DNA probes: comparison of hairpin versus linear capture probes

A microtiter-based assay system is described in which DNA hairpin probes with dangling ends and single-stranded, linear DNA probes were immobilized and compared based on their ability to capture single-strand target DNA. Hairpin probes consisted of a 16 bp duplex stem, linked by a T2-biotin·dT-T2 loop. The third base was a biotinylated uracil (UB) necessary for coupling to avidin coated microtiter wells. The capture region of the hairpin was a 3′ dangling end composed of either 16 or 32 bases. Fundamental parameters of the system, such as probe density and avidin adsorption capacity of the plates were characterized. The target DNA consisted of 65 bases whose 3′ end was complementary to the dangling end of the hairpin or to the linear probe sequence. The assay system was employed to measure the time dependence and thermodynamic stability of target hybridization with hairpin and linear probes. Target molecules were labeled with either a 5′-FITC, or radiolabeled with [γ-33P]ATP and captured by either linear or hairpin probes affixed to the solid support. Over the range of target concentrations from 10 to 640 pmol hybridization rates increased with increasing target concentration, but varied for the different probes examined. Hairpin probes displayed higher rates of hybridization and larger equilibrium amounts of captured targets than linear probes. At 25 and 45°C, rates of hybridization were better than twice as great for the hairpin compared with the linear capture probes. Hairpin–target complexes were also more thermodynamically stable. Binding free energies were evaluated from the observed equilibrium constants for complex formation. Results showed the order of stability of the probes to be: hairpins with 32 base dangling ends > hairpin probes with l6 base dangling ends > 16 base linear probes > 32 base linear probes. The physical characteristics of hairpins could offer substantial advantages as nucleic acid capture moieties in solid support based hybridization systems.

Parallel Changes in H2O2 and Catalase during Thermotolerance Induced by Salicylic Acid or Heat Acclimation in Mustard Seedlings1

Spraying mustard (Sinapis alba L.) seedlings with salicylic acid (SA) solutions between 10 and 500 μm significantly improved their tolerance to a subsequent heat shock at 55°C for 1.5 h. The effects of SA were concentration dependent, with higher concentrations failing to induce thermotolerance. The time course of thermotolerance induced by 100 μm SA was similar to that obtained with seedlings acclimated at 45°C for 1 h. We examined the hypothesis that induced thermotolerance involved H2O2. Heat shock at 55°C caused a significant increase in endogenous H2O2 and reduced catalase activity. A peak in H2O2 content was observed within 5 min of either SA treatment or transfer to the 45°C acclimation temperature. Between 2 and 3 h after SA treatment or heat acclimation, both H2O2 and catalase activity significantly decreased below control levels. The lowered H2O2 content and catalase activity occurred in the period of maximum thermoprotection. It is suggested that thermoprotection obtained either by spraying SA or by heat acclimation may be achieved by a common signal transduction pathway involving an early increase in H2O2.