Molecularly imprinted silica films prepared by electroassisted deposition for the selective detection of dopamine

Dopamine (DA) can be detected by electrochemical oxidation in conventional electrodes. However, the presence of other oxidizable species (interferents) usually present in physiological fluids at high concentrations (like ascorbic acid) makes very difficult its electrochemical detection. In the present work, glassy carbon electrodes have been modified with molecularly imprinted silica (MIS) films prepared by electroassisted deposition of sol–gel precursors. The production of MIS films was performed by adding the template molecule (DA) to the precursor sol. The molecular impression of silica was assessed showing a high coherency allowing a filtering capacity in the molecular scale. The MIS-modified electrodes present a high selectivity for the detection of DA in neutral or acidic solutions. The MIS-modified electrodes allow the amperometric determination of dopamine in solutions containing ascorbic acid with molar ratios lower than 1:50,000.

Mineral and chemical composition of hydrothermally altered rocks and sediments from the Middle Valley, ODP Leg 139 data

The Middle Valley segment at the northern end of the Juan de Fuca Ridge is a deep extensional rift blanketed with 200-500 m of Pleistocene turbiditic sediment. Sites 857 and 858 were drilled during Ocean Drilling Program Leg 139 to determine whether these two sites were hydrologically linked end members of an active hydrothermal circulation system. Site 858 was placed in an area of active hydrothermal discharge with fluids up to 270°C venting through anhydrite-bearing mounds on top of altered sediment. The shallow basement of fine-grained basalt that underlies the vents at Site 858 is interpreted as a seamount that was subsequently buried by turbidites. Site 857 was placed 1.6 km south of the Site 858 vents in a zone of high heat flow and numerous seismically imaged ridge-parallel faults. Drilling at Site 857 encountered sediments that are increasingly altered with depth and that overlie a series of mafic sills at depths of 460-940 m below sea floor. Sill margins and adjacent baked sediment are highly altered to magnesian chlorite and crosscut with veins filled with quartz, chlorite, sulfides, epidote, and wairakite. The sill interiors vary from slightly altered, with unaltered plagioclase and clinopyroxene in a mesostasis replaced by chlorite, to local zones of intense alteration and brecciation. In these latter zones, the sill interiors are pervasively replaced by chlorite, epidote, quartz, pyrite, titanite, and rare actinolite. The most complete replacement is associated with brecciated horizons with low recovery and slickensides on fracture surfaces, which we interpret as intersections between faults and the sills. Geochemically, the alteration of the sill complex is reflected in significant whole-rock depletions in Ca, Sr, and Na with corresponding enrichments in Mg, Al, and most metals. The latter results from the formation of conspicuous sulfide poikiloblasts. In contrast, metamorphism of the Site 858 seamount includes incomplete albitization of plagioclase phenocrysts and replacement of sparse mafic phenocrysts. Much of the basement alteration at Site 858 is confined to crosscutting veins except for a highly altered and veined horizon at the contact between basaltic basement and the overlying sediment. The sill complex at Site 857 is more highly depleted in 18O (d18O = 2.4 per mil - 4.7 per mil) and more pervasively replaced by secondary minerals relative to the extrusives at Site 858 (d18O = 4.5 per mil - 5.5 per mil). There is no evidence of significant albitization of the plagioclase at Site 857, suggesting high Ca/Na in the pore fluids. Fluid-inclusion data from hydrothermal minerals in altered mafic rocks and veins at Sites 857 and 858 show a consistency of homogenization temperatures, varying from 245 to 270°C, which is within the range of temperatures observed for the fluids venting at Site 858. The consistency of the fluid inclusion temperatures, the lack of albitization within the Site 857 sills, and the apparently low water/rock ratio collectively suggest that the sill complex at Site 857 is in thermal equilibrium and being altered by a highly evolved Ca-rich fluid similar to the fluids now venting at Site 858. The alteration evident in these two deep crustal drillsites is a result of the ongoing hydrothermal circulation and is consistent with downhole logging results, instrumented borehole results, and hydrothermal fluid chemistry. The pervasive alteration of the laterally extensive sill-sediment complex at Site 857 determines the chemistry of the fluids that are venting at Site 858. The limited alteration of the Site 858 lavas suggests that this basement edifice acts as a penetrator or ventilator for the regional hydrothermal reservoir with much of the flow focussed at the highly altered and veined sediment-basalt contact.

Chemical composition and solubility of ocean phosphatized rocks in seawater

In order to elucidate possibility of limestone phosphatization during contact with seawater two sets of experiments were carried out: that of solubility of natural phosphates in seawater and that of deposition of phosphorus onto calcareous phase. Concentration of phosphorus in seawater used for solubility experiments varied from 39 to 338 µ/l, temperature was 5.5-17.5°C and pH 7.8-7.9. The lowest solubility was characteristic of ancient crystallized samples. The deposition experiments showed that in case when concentration of dissolved phosphate in seawater reaches 3 mg/l it might be sorbed on solid CaCO3 phase without forming its own mineral. The latter is able to form rapidly but only if magnesium is not present in solution. In magnesium-free water calcium phosphates precipitate when concentration of dissolved phosphorus is higher than 0.9-1.2 mg/l. These results show that phosphatization of limestones in marine environment takes place during their contact with pore water but not with marine bottom water.

Chemical analyses of the clay fraction in selected samples of Sediment core KS09 (Table 2)

A deep-sea core over 16 m long from the crestal area of the Mediterranean Ridge has been investigated with different techniques, including quantitative micropaleontology, stable isotopes (measured on the epipelagic species Globigerinoides ruber and on the mesopelagic species Globorotalia inflata), and clay mineralogy. The resulting record of climatic fluctuations can be cross correlated to other Mediterranean cores by means of isochronous lithologies (tephra layers and sapropels). The climatic record of the Mediterranean is similar in character, phase, and chronology to the records investigated in the equatorial Pacific and in the Caribbean. Isotope stages 1 to 17 have been recognized. Cyclically repeated stagnant cycles resulting in sapropel deposition complicate both the isotopic and the faunal signal. The isotopic investigations reveal that the temperature change in the surface layers of the eastern Mediterranean was no greater than 8°C in the late "glacial" Pleistocene. The chronostratigraphic and biostratigraphic interpretation of Core KS09 indicate that the mean sedimentation rate was 2.4 cm/1000 years, a value very close to the 2.5 cm/1000 years calculated for the entire Quaternary section at DSDP Site 125, also located in the crestal area of the Mediterranean Ridge in the Ionian Basin. The base of KS09 is likely to be very close to the Brunhes/Matuyama boundary dated at 0.7 my.

Chemical composition of smectite-bearing basal metalliferous sediments from DSDP Leg 9

The mineralogy and P, Fe and Mn contents of basal metalliferous and nonmetalliferous sediments of two Deep Sea Drilling Project cores (Sites 77 and 80) were investigated. When compared with superjacent nonmetalliferous material, basal metalliferous sediments are significantly enriched in P, Fe and Mn. Among the phases present in the metalliferous sediment samples are a poorly-crystalline Fe-rich smectite and X-ray amorphous Fe oxyhydroxides. P is associated primarily with the oxyhydroxides. Adsorption of phosphate on smectite does not seem to play any role in the uptake of P by metalliferous sediments. An estimate of the removal of P by on- and off-ridge metallogenic deposition suggests that this process strongly affects the overall geochemical balance of phosphorus in the World Ocean.

Studies in vapor pressure ...

Reprinted from the Journal of the American Chemical Society, Nov. and Dec., 1910.

Effects of potential models in the vapor-liquid equilibria and adsorption of simple gases on graphitized thermal carbon black

In this paper, we investigate the effects of various potential models in the description of vapor–liquid equilibria (VLE) and adsorption of simple gases on highly graphitized thermal carbon black. It is found that some potential models proposed in the literature are not suitable for the description of VLE (saturated gas and liquid densities and the vapor pressure with temperature). Simple gases, such as neon, argon, krypton, xenon, nitrogen, and methane are studied in this paper. To describe the isotherms on graphitized thermal carbon black correctly, the surface mediation damping factor introduced in our recent publication should be used to calculate correctly the fluid–fluid interaction energy between particles close to the surface. It is found that the damping constant for the noble gases family is linearly dependent on the polarizability, suggesting that the electric field of the graphite surface has a direct induction effect on the induced dipole of these molecules. As a result of this polarization by the graphite surface, the fluid–fluid interaction energy is reduced whenever two particles are near the surface. In the case of methane, we found that the damping constant is less than that of a noble gas having the similar polarizability, while in the case of nitrogen the damping factor is much greater and this could most likely be due to the quadrupolar nature of nitrogen.

Chemical characterization of earth's most ancient clastic metasediments from the Isua Greenstone Belt, southern West Greenland

New and published major and trace element abundances of elastic metasediments (mainly garnet-biotite-plagioclase schists) from the similar to 3.8 Ga Isua Greenstone Belt (IGB), southern West Greenland, are used in an attempt to identify the compositional characteristics of the protoliths of these sediments. Compositionally, the metasediments are heterogeneous with enrichment of LREE (La/Sm-chord = 1.1-3.9) and variable enrichment and depletion of HREE (Gd/Yb-chord = 0.8-4.3). Chondrite-normalized Eu is also variable, spanning a range from relative Eu depletion to enrichment (Eu/Eu* = 0.6-1.3). A series of geochemical and geological criteria provides conclusive evidence for a sedimentary origin, in disagreement with some previous studies that questioned the presence of genuine elastic metasediments. In particular, trace element systematics of IGB metasediments show strong resemblance to other well-documented Archaean clastic sediments, and are consistent with a provenance consisting of ultramafic, malic and felsic igneous rocks. Two schists, identified as metasomatized mafic igneous rocks from petrographic and field evidence, show distinct compositional differences to the metasediments. Major element systematics document incipient-to-moderate source weathering in the majority of metasediments, while signs of secondary K-addition are rare. Detailed inspection of Eu/Eu*, Fe2O3 and CIW (chemical index of weathering) relationships reveals that elevated iron contents (when compared to averages for continental crust) and strong relative enrichment in Eu may be due to precipitation of marine Fe-oxyhydroxides during deposition or diagenesis on the seafloor. Some of the IGB metasediments have yielded anomalous Nd-142 and W-182 isotopic compositions that were respectively interpreted in terms of early mantle differentiation processes and the presence of a meteorite component. Alternatively, W and possibly Nd isotopes could have been affected by thermal neutron capture on the Hadean surface. The latter process was tested in this study by analysis of Sm isotope compositions, which serve as an effective monitor for neutron capture effects. As no anomalous variation from terrestrial values was detected, we infer that isotope systematics (including W-182 and Nd-142) of IGB metasediments were not affected by neutron capture, but reflect decay of radioactive parent isotopes. Copyright (c) 2005 Elsevier Ltd.

Synthesis and characterization of turbostratic carbons prepared by catalytic chemical vapour decomposition of acetylene

The turbostratic mesoporous carbon blacks were prepared by catalytic chemical vapour decomposition (CCVD) of acetylene using Ni/MgO catalysts prepared by co-precipitation. The relationship between deposition conditions and the nanostructures of resultant carbon black materials was investigated. It was found that the turbostratic and textural structures of carbon blacks are dependent on the deposition temperature and nickel catalyst loading. Higher deposition temperature increases the carbon crystallite unit volume V-nano and reduces the surface area of carbon samples. Moreover, a smaller V-nano is produced by a higher Ni loading at the same deposition temperature. In addition of the pore structure and the active metal surface area of the catalyst, the graphitic degree or electronic conductivity of the carbon support is also a key issue to the activity of the supported catalyst. V-nano is a very useful parameter to describe the effect of the crystalline structure of carbon blacks on the reactivity of carbon blacks in oxygen-carbon reaction and the catalytic activity of carbon-supported catalyst in ammonia decomposition semi-quantitatively. (C) 2006 Elsevier B.V. All rights reserved.

Prediction of vapor-moisture equilibriums for a wood-moisture system using a modified UNIQUAC model

A modified UNIQUAC model has been extended to describe and predict the equilibrium relative humidity and moisture content for wood. The method is validated over a range of moisture content from oven-dried state to fiber saturation point, and over a temperature range of 20-70 degrees C. Adjustable parameters and binary interaction parameters of the UNIQUAC model were estimated from experimental data for Caribbean pine and Hoop pine as well as data available in the literature. The two group-interaction parameters for the wood-moisture system were consistent with using function group contributions for H2O, -OH and -CHO. The result reconfirms that the main contributors to water adsorption in cell walls are the hydroxyl groups of the carbohydrates in cellulose and hemicelluloses. This provides some physical insight into the intermolecular force and energy between bound water and the wood material. (c) 2006 Elsevier Ltd. All rights reserved.

Effect of deposition conditions on mechanical properties of low-temperature PECVD silicon nitride films

The effect of deposition conditions on characteristic mechanical properties - elastic modulus and hardness - of low-temperature PECVD silicon nitrides is investigated using nanoindentation. lt is found that increase in substrate temperature, increase in plasma power and decrease in chamber gas pressure all result in increases in elastic modulus and hardness. Strong correlations between the mechanical properties and film density are demonstrated. The silicon nitride density in turn is shown to be related to the chemical composition of the films, particularly the silicon/nitrogen ratio. (c) 2006 Elsevier B.V. All rights reserved.

A blank slate? Layer-by-layer deposition of hyaluronic acid and chitosan onto various surfaces

Although poly(alpha-hydroxy esters), especially the PLGA family of lactic acid/glycolic acid copolymers, have many properties which make them promising materials for tissue engineering, the inherent chemistry of surfaces made from these particular polymers is problematic. In vivo, they promote a strong foreign-body response as a result of nonspecific adsorption and denaturation of serum proteins, which generally results in the formation of a nonfunctional fibrous capsule. Surface modification post-production of the scaffolds is an often-utilized approach to solving this problem, conceptually allowing the formation of a scaffold with mechanical properties defined by the bulk material and molecular-level interactions defined by the modified surface properties. A promising concept is the so-called blank slate: essentially a surface that is rendered resistant to nonspecific protein adsorption but can be readily activated to covalently bind bio-functional molecules such as extracellular matrix proteins, growth factors or polysaccharides. This study focuses on the use of the quartz crystal microbalance (QCM) to follow the layer-by-layer (LbL) electrostatic deposition of high molecular weight hyaluronic acid and chitosan onto PLGA surfaces rendered positively charged by aminolysis, to form a robust, protein-resistant coating. We further show that this surface may be further functionalized via the covalent attachment of collagen IV, which may then be used as a template for the self-assembly of basement membrane components from dilute Matrigel. The response of NIH-3T3 fibroblasts to these surfaces was also followed and shown to closely parallel the results observed in the QCM.

Ocular compatibility of hydrogel contact lenses:deposition and clinical performance

Currently over 50 million people worldwide wear contact lenses, of which over 75% wear hydrogel lenses. Significant deposition occurs in approximately 80% of hydrogel lenses and many contact lens wearers cease wearing lenses due to problems associated with deposition. The contact lens field is not alone in encountering complications associated with interactions between the body and artificial devices. The widespread use of man-made materials to replace structures in the body has emphasised the importance of studies that examine the interactions between implantation materials and body tissues.This project used carefully controlled, randomized clinical studies to study the interactive effects of contact lens materials, care systems, replacement periods and patient differences. Of principal interest was the influence of these factors on material deposition and their subsequent impact on subjective performance. A range of novel and established analytical techniques were used to examine hydrogel lenses following carefully controlled clinical studies in which clinical performance was meticulously monitored. These studies established the inter-relationship between clinical performance and deposition to be evaluated. This project showed that significant differences exist between individuals in their ability to deposit hydrogel lenses, with approximately 20% of subjects displaying significant deposition irrespective of the lens material. Additionally, materials traditionally categorised together show markedly different spoilation characteristics, which are wholly attributable to their detailed chemical structure. For the first time the in vivo deposition kinetics of both protein and lipid in charged and uncharged polymers was demonstrated. In addition the importance of care systems in the deposition process was shown, clearly demonstrating the significance of the quality rather than the quantity of deposition in influencing subjective performance.