High pressure compression of filter cakes

The purpose of this thesis was to investigate the compression of filter cakes at high filtration pressures with five different test materials and to compare the energy consumption of high pressure compression with the energy consumption of thermal drying. The secondary target of this study was to investigate the particle deformation of test materials during filtration and compression. Literature part consists of basic theory of filtration and compression and of the basic parameters that influence the filtration process. There is also a brief description about all of the test materials including their properties and their industrial production and processing. Theoretical equations for calculating the energy consumptions of the filtrations at different conditions are also presented. At the beginning of the experiments at experimental part, the basic filtration tests were done with all the five test materials. Filtration tests were made at eight different pressures, from 6 bars up to 100 bars, by using piston press pressure filter. Filtration tests were then repeated by using a cylinder with smaller slurry volume than in the first series of filtration tests. Separate filtration tests were also done for investigating the deformation of solid particles during filtration and for finding the optimal curve for raising the filtration pressure. Energy consumption differences between high pressure filtration and ideal thermal drying process were done partly experimentally and partly by using theoretical calculation equations. By comparing these two water removal methods, the optimal ranges for their use were found considering their energy efficiency. The results of the measurements shows that the filtration rate increased and the moisture content of the filter cakes decreased as the filtration pressure was increased. Also the porosity of the filter cakes mainly decreased when the filtration pressure was increased. Particle deformation during the filtration was observed only with coal particles.

Start-up of anaerobic reactors for slaughterhouse wastewater treatment

This study aimed to evaluate the start-up of a horizontal anaerobic fixed bed reactor (HAFBR) followed by an upflow anaerobic sludge blanket (UASB) for the slaughterhouse wastewater treatment. HAFBR was filled with bamboo rings and had 1.2 m in length, 0.10 m in diameter and volume of 7.5 L. The UASB had the volume of 15 L. The HAFBR and UASB operated at organic loading rate and hydraulic retention time average of 8.46 and 3.77 kg m-3 d-1 of COD and 0.53 and 0.98 days, respectively. During 150 days of monitoring system it was found pH 6.8, relatively high values of bicarbonate alkalinity (> 1000 mg L-1) and reduced values of volatile acids (70 to 150 mg L-1), which afforded average removal efficiencies of COD total and total suspended solids of the order of 31 and 23% in HAFBR and 79% and 63% in UASB. It can be concluded that the generation and consumption of bicarbonate alkalinity and total volatile acids, thereby maintaining the pH during the study indicated stable operation of the reactors. The COD removal in the reactors was satisfactory especially when it considers that the assessment was conducted in a period of adaptation of organisms to the effluent and also the high organic load applied during this period.

Développement d’une méthode d’extraction des contaminants émergents dans les solides particulaires par LDTD-APCI-MS/MS

Douze contaminants émergents (composés pharmaceutiques, pesticides et hormones) ont été quantifiés et extraits de l'eau de rivières et d’échantillons d'eaux usées municipales. La séparation des solides en suspension est effectuée par filtration des échantillons d'eau. L'effet de filtration sur les concentrations de contaminants dissous a été évaluée afin de minimiser les pertes de composés cibles. Les échantillons ont été lyophilisés et ont été extraits en deux cycles par ultrasons combinés avec une étape de nettoyage sur cartouche d’extraction de type C18. La quantification a été réalisée en utilisant la spectrométrie de masse. Les recouvrements de la méthode pour tous les composés ont varié de 68 à 112% dans toutes les matrices étudiées, sauf pour le sulfaméthoxazole et le diclofénac où des recouvrements plus modestes ont été obtenus (38 à 85%). Les limites de détection pour les 12 analytes dans les sédiments et particules en suspension (SPM) de la rivière variaient de 0,7 à 9,4 ng g-1 et de 21 à 92 ng g-1, pour les échantillons SPM de station d'épuration. Tous les contaminants émergents cibles ont été détectés à des concentrations variant de 3 à 5440 ng g-1 dans les matrices étudiées, les concentrations les plus élevées ont été observées dans les échantillons SPM de stations d'épuration. Une partie importante de certains de ces contaminants est clairement associée aux sédiments de rivière ou aux particules en suspension. L’optimisation des processus de traitement de l'eau et le devenir environnemental doit absolument tenir compte de la fraction de contaminants qui liée à des particules si on espère avoir un bilan de masse raisonnable.

"|mpact of trawling on sea bottom and its living communities along the inshore waters of southwest coast of India'’

Mechanized fishing started in Indian waters in mid —fifties and large-scale operation of trawl fishing began in the mid sixties by the surfeit of individual entrepreneurs. The southwest coast of India especially the coastal waters of Kerala are the most productive area in the subcontinent and the state has been in the forefront in marine fish production (Kurup, 2001a). Though the coastline of Kerala is one tenth of the coastline of India, the state occupies the foremost position in the marine fish production of the country, accounting for more than 30% of the marine fish landings (Thomas, 2000). The coastal waters of Kerala have rich and diversified fishery resources, which are prone to heavy exploitation by a unprecedently high number of fishing gears, among them, mechanized bottom trawlers with a numerical strength of 4550 (Kurup, 2001a) against the permissible number of 1145 (Kalawar, et al., 1985) are the most destructive. Trawling operations during monsoon periods in Kerala has been a subject of controversy between traditional fishermen and trawl fishers on a subject that trawl fishing destroys large amount of juveniles and young ones of fishes since this period is the major breeding season of most of the fish and prawns (John, 1996). Therefore Government of Kerala imposed a ban on bottom trawling activities from 1988 onwards for a period varying from 21-70 days, which usually commences from June 15th. Though many studies revealed that large amount of non-target groups were destroyed in the commercial trawl fishing in the Indian waters, no concerted study has been conducted so far to evaluate the real impact of bottom trawling on the sea bottom and its living communities. The present study was conducted to assess the impact of excessive bottom trawling exerted on the sea bottom habitat and its living communities, which would be useful in impressing up on the seriousness of habitat degradation and biotic devastation, enabling the concerned to adopt relevant conservation and management steps to conserve the resources for sustainable exploitation

Sewage effluent clean-up reduces phosphorus but not phytoplankton in lowland chalk stream (River Kennet, UK) impacted by water mixing from adjacent canal

Information is provided on phosphorus in the River Kennet and the adjacent Kennet and Avon Canal in southern England to assess their interactions and the changes following phosphorus reductions in sewage treatment work (STW) effluent inputs. A step reduction in soluble reactive phosphorus (SRP) concentration within the effluent (5 to 13 fold) was observed from several STWs discharging to the river in the mid-2000s. This translated to over halving of SRP concentrations within the lower Kennet. Lower Kennet SRP concentrations change from being highest under base-flow to highest under storm-flow conditions. This represented a major shift from direct effluent inputs to a within-catchment source dominated system characteristic of the upper part to the catchment. Average SRP concentrations in the lower Kennet reduced over time towards the target for good water quality. Critically, there was no corresponding reduction in chlorophyll-a concentration, the waters remaining eutrophic when set against standards for lakes. Following the up gradient input of the main water and SRP source (Wilton Water), SRP concentrations in the canal reduced down gradient to below detection limits at times near its junction with the Kennet downstream. However, chlorophyll concentrations in the canal were in an order of magnitude higher than in the river. This probably resulted from long water residence times and higher temperatures promoting progressive algal and suspended sediment generations that consumed SRP. The canal acted as a point source for sediment, algae and total phosphorus to the river especially during the summer months when boat traffic disturbed the canal's bottom sediments and the locks were being regularly opened. The short-term dynamics of this transfer was complex. For the canal and the supply source at Wilton Water, conditions remained hypertrophic when set against standards for lakes even when SRP concentrations were extremely low.

An exploration of the equivalent weights particle filter

Particle filters are fully non-linear data assimilation techniques that aim to represent the probability distribution of the model state given the observations (the posterior) by a number of particles. In high-dimensional geophysical applications the number of particles required by the sequential importance resampling (SIR) particle filter in order to capture the high probability region of the posterior, is too large to make them usable. However particle filters can be formulated using proposal densities, which gives greater freedom in how particles are sampled and allows for a much smaller number of particles. Here a particle filter is presented which uses the proposal density to ensure that all particles end up in the high probability region of the posterior probability density function. This gives rise to the possibility of non-linear data assimilation in large dimensional systems. The particle filter formulation is compared to the optimal proposal density particle filter and the implicit particle filter, both of which also utilise a proposal density. We show that when observations are available every time step, both schemes will be degenerate when the number of independent observations is large, unlike the new scheme. The sensitivity of the new scheme to its parameter values is explored theoretically and demonstrated using the Lorenz (1963) model.

A Floating-point Extended Kalman Filter Implementation for Autonomous Mobile Robots

Localization and Mapping are two of the most important capabilities for autonomous mobile robots and have been receiving considerable attention from the scientific computing community over the last 10 years. One of the most efficient methods to address these problems is based on the use of the Extended Kalman Filter (EKF). The EKF simultaneously estimates a model of the environment (map) and the position of the robot based on odometric and exteroceptive sensor information. As this algorithm demands a considerable amount of computation, it is usually executed on high end PCs coupled to the robot. In this work we present an FPGA-based architecture for the EKF algorithm that is capable of processing two-dimensional maps containing up to 1.8 k features at real time (14 Hz), a three-fold improvement over a Pentium M 1.6 GHz, and a 13-fold improvement over an ARM920T 200 MHz. The proposed architecture also consumes only 1.3% of the Pentium and 12.3% of the ARM energy per feature.

Identification of lift-off mechanism failure for salt drill-in drilling fluid containing polymer filter cake through adsorption/desorption studies

Drilling fluid`s contact with the productive zone of horizontal or complex wells can reduce well productivity by fluid invasion in the borehole wall. Salted drilling drill-in fluid containing polymers has often been applied in horizontal or complex petroleum wells in the poorly consolidated sandstone reservoirs of the Campos basin, Rio de Janeiro, Brazil. This fluid usually consists of natural polymers such as starch and xanthan gum, which are deposited as a filter cake on the wellbore wall during the drilling. Therefore, the identification of a lift-off mechanism failure, which can be detachment or blistering and pinholing, will enable formulation improvements. increasing the chances of success during filter cake removal in open hole operations. Likewise, knowledge of drill-in drilling fluid adsorption/desorption onto sand can help understand the filter cake-rock adhesion mechanism and consequently filter cake lift-off mechanism failures. The present study aimed to identify the lift-off failure mechanism for this type of fluid filter cake studying adsorption/desorption onto SiO(2) using solutions of natural polymers, lubricants, besides the fluid itself. Ellipsometry was employed to measure this process. The adsorption/desorption studies showed that the adsorbed layer of drilling fluid onto the walls of the rock pores is made up of clusters of polymers, linked by hydrogen bonds, which results in a force of lower cohesion compared to the electrostatic interaction between silica and polymers. Consequently, it was found that the most probable filter cake failure mechanism is rupture (blistering and pinholing), which results in the formation of ducts within the filter cake. (C) 2009 Elsevier B.V. All rights reserved.

Fatigue-free behavior of Bi3.25La0.75Ti3O12 thin films grown on several bottom eletrodes by the polymeric precursor method

Fatigue-free Bi3.25La0.75Ti3O12 (BLT) thin films were grown on LaNiO3,RuO2, and La0.5Sr0.5CoO3 bottom electrodes in a microwave furnace at 700 degreesC for 10 min. The remanent polarization (P-r) and the drive voltage (V-c) were in the range of 11-23 muC/cm(2) and 0.86-1.56 V, respectively, and are better than the values found in the literature. The BLT capacitors did not show any significant fatigue up to 10(10) read/write switching cycles. (C) 2004 American Institute of Physics.

Search for third-generation leptoquarks and scalar bottom quarks in pp collisions at √s=7Tev

Results are presented from a search for third-generation leptoquarks and scalar bottom quarks in a sample of proton-proton collisions at √s=7Tev collected by the CMS experiment at the LHC, corresponding to an integrated luminosity of 4.7 fb-1. A scenario where the new particles are pair produced and each decays to a b quark plus a tau neutrino or neutralino is considered. The number of observed events is found to be in agreement with the standard model prediction. Upper limits are set at 95% confidence level on the production cross sections. Leptoquarks with masses below ~450 GeV are excluded. Upper limits in the mass plane of the scalar quark and neutralino are set such that scalar bottom quark masses up to 410 GeV are excluded for neutralino masses of 50 GeV. © 2012 CERN for the benefit of CMS collaboration.

Poço de infiltração para controle de enchentes na fonte: avaliação das condições de operação e manutenção

This study investigated the following aspects regarding a soakaway, i.e. an infiltration well: i) entrance filter device; ii) permeability of the geotextile; and iii) emptying time. The 3.6 m³ infiltration well drains a roof area of 241.8 m². The entrance device is made up of layers of sand, gravel and geotextile set on a metal structure. The concrete rings that form the lateral walls were covered with geotextile, and bricks were laid between the soil and concrete rings. The infiltration well remained in operation during the entire testing period, and specific events were simulated to measure the emptying time. Permeability and fine particle tests were carried out after eight months of operation. Samples of geotextile taken from the bottom, the walls and the entrance device presented average permeability reductions of approximately 50.7%, 7.7% and 21.2%, respectively. The sand in the entrance device retained around 34.8% of fine particles and the gravel retained 0.13% in the same period. The infiltration rate was approximately 34.7 mm/h. The R2 coefficient for measured and calculated times was 0.97.

Search for the standard model Higgs boson produced in association with a W or a Z boson and decaying to bottom quarks

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Organismi acquatici e ambiente: meccanismi biochimici di interazione, risposta e adattamento

The research is focused on the relationship between some Mg2+-dependent ATPase activities of plasma- and mitochondrial membranes from tissues of cultured marine bivalve molluscs and potentially stressful environmental conditions, such as the exposure to contaminants both of natural origin (ammonia nitrogen, the main contaminant of aquaculture plants) and of anthropic source (alkyltins). The two filter-feeding bivalve species selected colonize different habitats: the common mussel Mytilus galloprovincialis binds to hard substrates and the Philippine clam Tapes philippinarum burrows into sea bottom sandy beds. The choice of typical species of coastal waters, extremely suitable for environmental studies due to their features of poor motility, resistance to transport and great filtering efficiency, may constitute a model to evaluate responses to contaminants of membrane-bound enzyme activities involved in key biochemical mechanisms, namely cell ionic regulation and mitochondrial energy production. In vitro and in vitro approaches have been pursued. In vitro assays were carried out by adding the contaminants (NH4Cl and alkyltins) directly to the ATPase reaction media. In vivo experiments were carried out by exposing mussels to various tributyl tin (TBT) concentrations under controlled conditions in aquaria. ATPase activities were determined spectrophotometrically according to the principles of the method of Fiske and Subbarow (1925). The main results obtained are detailed below. In Tapes philippinarum the interaction of NH4 +, the main form of ammonia nitrogen at physiological and seawater pHs, with the Na,K-ATPase and the ouabaininsensitive Na-ATPase was investigated in vitro on gill and mantle microsomal membranes. The proven replacement by NH4 +of K+ in the activation of the Na,KATPase and of Na+ in the activation of the ouabain-insensitive ATPase displayed similar enzyme affinity for the substituted cation. on the one hand this finding may represent one of the possible mechanisms of ammonia toxicity and, on the other, it supports the hypothesis that NH4 + can be transported across the plasma membrane through the two ATPases. In this case both microsomal ATPases may be involved and co-operate, at least under peculiar circumstances, to nitrogen excretion and ammonia detoxification mechanisms in bivalve molluscs. The two ATPase activities stimulated by NH4 + maintained their typical response to the glycoside ouabain, specific inhibitor of the Na,K-ATPase, being the Na++ NH4 +-activated ATPase even more susceptive to the inhibitor and the ouabain-insensitive ATPase activity activated indifferently by Na+ or NH4 + unaffected by up to 10-2 M ouabain. In vitro assays were carried out to evaluate the response of the two Na-dependent ATPases to organotins in clams and mussels and to investigate the interaction of TBT with mussel mitochondrial oligomycin-sensitive Mg-ATPase. Since no literature data were available, the optimal assay conditions and oligomycin sensitivity of mussel mitochondrial MgATPase were determined. In T. philippinarum the ouabain-insensitive Na-ATPase was found to be refractory to TBT both in the gills and in the mantle, whereas the Na,K-ATPase was progressively inhibited by increasing TBT doses; the enzyme inhibition was more pronounced in the gills than in the mantle. In both tissues of M. galloprovincialis the Na,K-ATPase inhibition by alkyltins decreased in the order TBT>DBT(dibutyltin)>>MBT(monobutyltin)=TeET(tetraethyltin) (no effect). Mussel Na-ATPase confirmed its refractorimess to TBT and derivatives both in the gills and in the mantle. These results indicate that the Na,K-ATPase inhibition decreases as the number of alkyl chains bound to tin decreases; however a certain polarity of the organotin molecule is required to yield Na,K-ATPase inhibition, since no enzyme inhibition occurred in the presence of tetraalkyl-substituted derivatives such as TeET . Assays carried out in the presence of the dithioerythritol (DTE) pointed out that the sulphhydrylic agent is capable to prevent the Na,K-ATPase inhibition by TBT, thus suggesting that the inhibitor may link to -SH groups of the enzyme complex.. Finally, the different effect of alkyltins on the two Na-dependent ATPases may constitute a further tool to differentiate between the two enzyme activities. These results add to the wealth of literature data describing different responses of the two enzyme activities to endogenous and exogenous modulators . Mussel mitochondrial Mg-ATPase was also found to be in vitro inhibited by TBT both in the gills and in the mantle: the enzyme inhibition followed non competitive kinetics. The failed effect of DTE pointed out that in this case the interaction of TBT with the enzyme complex is probably different from that with the Na,K-ATPase. The results are consistent with literature data showing that alkyltin may interact with enzyme structures with different mechanisms. Mussel exposure to different TBT sublethal doses in aquaria was carried out for 120 hours. Two samplings (after 24 and 120 hrs) were performed in order to evaluate a short-term response of gill and mantle Na,K-ATPase, ouabain-insensitive Na-ATPase and Mg-ATPase activities. The in vivo response to the contaminants of the enzyme activities under study was shown to be partially different from that pointed out in the in vitro assays. Mitochondrial Mg-ATPase activity appeared to be activated in TBTexposed mussels with respect to control ones, thus confirming the complexity of evaluating in vivo responses of the enzyme activities to contaminants, due to possible interactions of toxicants with molluscan metabolism. Concluding, the whole of data point out that microsomal and mitochondrial ATPase activities of bivalve molluscs are generally responsive to environmental contaminants and suggest that in some cases membrane-bound enzyme activities may represent the molecular target of their toxicity. Since the Na,K-ATPase, the Na-ATPase and the Mg-ATPase activities are poorly studied in marine bivalves, this research may contribute to enlarge knowledge in this quite unexplored field.

Creation of Computer Simulation Model for Ecological Consequences Prognosis of Toxic Chemicals Discharge from Sunken on Baltic Sea Bottom Weapons"

This study summarises all the accessible data on old German chemical weapons dumped in the Baltic Sea. Mr. Goncharov formulated a concept of ecological impact evaluation of chemical warfare agents (CWA) on the marine environment and structured a simulation model adapted to the specific character of the hydrological condition and hydrobiological subjects of the Bornholm Deep. The mathematical model he has created describes the spreading of contaminants by currents and turbulence in the near bottom boundary layer. Parameters of CWA discharge through corrosion of canisters were given for various kinds of bottom sediments with allowance for current velocity. He created a method for integral estimations and a computer simulation model and completed a forecast for CWA "Mustard", which showed that in normal hydrometeorological conditions there are local toxic plumes drifting along the bottom for a distance of up to several kilometres. With storm winds the toxic plumes from separate canisters interflow and lengthen and can reach fishery areas near Bornholm Island. When salt water from the North Sea flows in, the length of toxic zones can increase up to and over 100 kilometres and toxic water masses can spread into the northern Baltic. On this basis, Mr. Goncharov drew up recommendations to reduce dangers for human ecology and proposed the creation of a special system for the forecasting and remote sensing of the environmental conditions of CWA burial places.

Optional vena cava filter with disengaging centering struts: retrieval in an animal model

An optional inferior vena cava (IVC) filter prototype was evaluated for safety and long-term retrievability as an initial feasibility study in an animal model. This filter has four centering struts that have the ability to disengage from the filtering cone portion, allowing the legs to slide out of endothelial growth. Retrieval of six filters in three animals was successful up to 27 weeks. There was no substantial filter tilt, migration, or IVC damage. In conclusion, this filter design may help overcome some of the shortcomings in currently approved optional IVC filters, including long-term retrieval difficulties, tilting, or migration.