Statistical Analysis and Numerics of Heat Exchanger Models

The identifiability of the parameters of a heat exchanger model without phase change was studied in this Master’s thesis using synthetically made data. A fast, two-step Markov chain Monte Carlo method (MCMC) was tested with a couple of case studies and a heat exchanger model. The two-step MCMC-method worked well and decreased the computation time compared to the traditional MCMC-method. The effect of measurement accuracy of certain control variables to the identifiability of parameters was also studied. The accuracy used did not seem to have a remarkable effect to the identifiability of parameters. The use of the posterior distribution of parameters in different heat exchanger geometries was studied. It would be computationally most efficient to use the same posterior distribution among different geometries in the optimisation of heat exchanger networks. According to the results, this was possible in the case when the frontal surface areas were the same among different geometries. In the other cases the same posterior distribution can be used for optimisation too, but that will give a wider predictive distribution as a result. For condensing surface heat exchangers the numerical stability of the simulation model was studied. As a result, a stable algorithm was developed.

Characterization and Control Strategies of an Integrated Chemical-Biological System for the Remediation of Toxic Pollutants in Wastewater: A case of study

In a previous work, a hybrid system consisting of an advanced oxidation process (AOP) named Photo-Fenton (Ph-F) and a fixed bed biological treatment operating as a sequencing batch biofilm reactor (SBBR) was started-up and optimized to treat 200 mg·L-1 of 4-chlorophenol (4-CP) as a model compound. In this work, studies of reactor stability and control as well as microbial population determination by molecular biology techniques were carried out to further characterize and control the biological reactor. Results revealed that the integrated system was flexible and even able to overcome toxic shock loads. Oxygen uptake rate (OUR) in situ was shown to be a valid tool to control the SBBR operation, to detect toxic conditions to the biomass, and to assess the recovery of performance. A microbial characterization by 16S rDNA sequence analysis reveals that the biological population was varied, although about 30% of the bacteria belonged to the Wautersia genus.

Control d'un sistema de marcatge làser de caixes

Avui en dia, l’alta competitivitat que existeix al mercat, fa que les empreses hagin d’esprémer al màxim les seves possibilitats per no quedar-se enrere. Un dels processos en que aquest fet hi és més present és el productiu. L’empresa JCM Technologies també engloba aquest camp i és en un dels seus processos productius on aquest projecte pren part. L’objectiu d’aquest projecte final de carrera ha estat desenvolupar un sistema per poder marcar caixes mitjançant un làser de CO2 i un automatisme manipulador de caixes. D’aquesta manera aquest procés productiu té una durada molt inferior a l’antic procés, que consistia en enganxar una etiqueta al lloc on ara és marcat pel làser. Per satisfer els objectius, s’ha creat una aplicació de Windows que per mitjà d’una interfície gràfica, permet a l’usuari realitzar els passos necessaris per fer el marcatge. Primerament es recullen les dades procedents de la comanda; seguidament es seleccionen les que s’han de marcar a les caixes i s’envien al làser mitjançant comunicació sèrie; una vegada aquesta inicialització ha finalitzat correctament, s’engega la seqüència de marcatge de les caixes, que en marcarà la quantitat indicada. Aquest procés de marcatge consisteix en supervisar l’estat en que es troben certes senyals, procedents de l’automatisme i del làser, i depenent d’aquestes generar-ne unes altres. Aconseguint així realitzar el procés de marcatge de cada caixa. Com a conclusions cal dir, que els objectius s’han complert, ja que s’ha aconseguit un procés de marcatge ràpid i robust. També s’ha aconseguit que les parts de configuració de l’aplicació, i de les caixes siguin de fàcil manipulació. Per tant, amb l’acompliment dels objectius d’aquest projecte, aconseguim completar el sistema de marcatge, i permetre que les caixes siguin marcades de forma correcta, ràpida i eficient.

Control de 6 respiròmetres i anàlisi de les dades

L’aplicació de tècniques respiromètriques és de recent innovació dins l’estudi dels tractaments d’aigües residuals. Aquest conjunt de tècniques ens permeten analitzar dos processos importants dins una planta de tractament biològic: el creixement de la biomassa i el consum del substrat. Això fa que siguin una eina amb gran potencial en l’avaluació dels sistemes de tractament biològic d’aigües residuals. L’objectiu principal d’aquest treball es la realització d’una aplicació capaç de controlar el funcionament de 6 respiròmetres, gestionant el procés del mostreig de les respirometries i l’anàlisi de les dades obtingudes, per obtenir el substrat ràpidament biodegradable (Ss) per a mostres d’aigua residual, i la taxa màxima de creixement específic per a mostres de compost. L’aplicació s’ha desenvolupat sobre l’entorn Microsoft Access, on s’integren la base de dades amb les mostres i els resultats de les respirometries, i els formularis de control que ens permeten gestionar i controlar els processos de mostreig i anàlisi. L’aplicació es comunica amb els sensors i actuadors dels respiròmetres a través del control ActiveX, ADS-OCX, subministrat per TwinCAT, que ens permet capturar les lectures dels sensors i controlar el funcionament dels actuadors. Aquests elements estan connectats a mòduls descentralitzats d’entrades i sortides, comunicats mitjançant el bus Ethernet amb el PC-Industrial, on s’executa l’aplicació. Un cop finalitzada l’aplicació, aquesta controla correctament el mostreig de les respirometries, registrant les lectures de les sondes a la base de dades i controlant l’activació de les vàlvules del respiròmetre. Partint de les mostres obtingudes, o de respirometries externes, importades des de Microsoft Excel, s’ha comprovat el correcte funcionament en el càlcul del substrat ràpidament biodegradable (Ss) i la taxa màxima de creixement específic. Amb l’aplicació desenvolupada, s’ha comprovat el funcionament i les possibilitats que ens ofereix TwinCAT alhora de controlar mòduls d’entrades i sortides, així com la seva comunicació amb aplicacions com Microsoft Access. Això pot afavorir a la utilització d’aquest tipus de tecnologia, per aplicacions futures.

Creació d'una botiga virtual i automatització dels albarans, factures i cobraments

L’augment de la utilització de les noves tecnologies a la nostra societat permet a les empreses arribar al client d’una forma més rapida i facilitant la informació de manera àgil i ordenada. Amb aquest objectiu s’ha creat una botiga virtual que serà la part visible als usuaris i clients de l’empresa PRINTONER S.L , dedicada al sector dels consumibles, especialment els reciclats. Per l’empresa un dels objectius principals és oferir al client la possibilitat de comprar els seus productes de manera còmode a través d’Internet, ja que accedint amb un nom d’usuari i una contrasenya podrà obtenir totes les referències de les que es disposa, podrà tramitar les comandes i controlar-ne l’estat fins el moment de l’entrega. A part de les seccions destinades a usuaris i clients s’ha creat una zona d’administració, on els responsables de l’empresa podran gestionar tots els productes, modificar i visualitzar les comandes. A més aprofitant que aquestes quedaran guardades a una base de dades juntament amb els productes venuts, s’integrarà el sistema de facturació de l’empresa, cosa que fins el moment es feia de manera manual i maldestre. També es programarà una part on els responsables podran insertar reparacions i vendes informàtiques que s’hagin de facturar o per fer-ne un us estadístic en un futur. Tot això ens portarà a implementar un sistema d’usuaris registrats amb diferents permisos i diferents nivells d’accés a l’aplicació, fins a un total de 5. S’ha intentat fer de l’aplicació, un sistema a mida i que compleixi tots els requisits que l’empresa ens ha demanat, amb la previsió que més endavant s’hi pugui implementar un sistema de gestió d’estocs i altres millores per oferir als seus clients un servei inigualable. Per tal de portar a terme tot aquest treball s’ha utilitzat una tecnologia de lliure distribució com és el llenguatge PHP i la base de dades MySQL, aquesta opció a part d’una filosofia es produeix per intentar minimitzar els costos de l’aplicatiu. La finalitat de l’empresa amb aquest projecte és oferir millor imatge i servei, efectivitat i rapidesa en tot el procés de vendes, així com reduir costos de facturació i també de publicitat, ja que es podrà potenciar molt més la pàgina web via internet.

Control de la derivació de l'aigua de reg de Masjoan

RESUM Masjoan és una masia del segle XII on resideix la família Masferrer des del 1710. Actualment a Masjoan l’activitat principal és el cultiu i venta de plantes ornamentals, i l’explotació forestal per obtenir fusta. Pel que fa a l’aigua, tant per a la realització de l’activitat professional com per al subministrament de la casa, aquesta prové de mines d’aigua natural situades en la finca. L’objectiu d’aquest TFC ha estat dissenyar un sistema autònom per automatitzar el procés de derivació de l’aigua procedent d’una mina, i d’aquesta manera aprofitar millor els recursos naturals dels que és disposa. El desenvolupament d’aquest sistema, comprèn la selecció i configuració de sensors i actuadors, el disseny del circuit amb la realització de la placa, el disseny del sistema d’alimentació autònom, el software que controla el sistema, i dimensionar la resta d’elements de la instal•lació. Tot el sistema està controlat per un microcontrolador PIC16F876 i alimentat per un mòdul solar de 4W. En el disseny s’ha procurat, sobredimencionar les diferents etapes per possibles ampliacions o modificacions del sistema i que el circuit procures optimitzar el consum d’energia. Com a conclusions cal dir que s’han assolit els objectius proposats amb èxit. S’ha aconseguit un disseny funcional i estable que actualment es troba en funcionament.

A Fair and Secure Cluster Formation Process for Ad Hoc Networks

An efficient approach for organizing large ad hoc networks is to divide the nodesinto multiple clusters and designate, for each cluster, a clusterhead which is responsible forholding intercluster control information. The role of a clusterhead entails rights and duties.On the one hand, it has a dominant position in front of the others because it manages theconnectivity and has access to other node¿s sensitive information. But on the other hand, theclusterhead role also has some associated costs. Hence, in order to prevent malicious nodesfrom taking control of the group in a fraudulent way and avoid selfish attacks from suitablenodes, the clusterhead needs to be elected in a secure way. In this paper we present a novelsolution that guarantees the clusterhead is elected in a cheat-proof manner.

Improved method to obtain pfaffic acid as a marker for quality control

Pfaffic acid, a marker of Hebanthe eriantha (Brazilian ginseng), was first isolated in 1983 but is not yet commercially available. This lack of availability compromises the quality control of this plant and its derivatives. This paper proposes a process for pfaffic acid isolation from roots of H. eriantha at a purity suitable for analytical purposes. The steps involved in this process included extraction, hydrolysis, fractionation and purification by preparative HPLC. This process led to isolation of pfaffic acid with a chromatographic purity of 98.5% in a 0.25% yield from dried roots of H. eriantha; this yield is more than forty times higher than that of the current method in the literature.

Grape juice quality control by means of ¹H nmr spectroscopy and chemometric analyses

This work shows the application of ¹H NMR spectroscopy and chemometrics for quality control of grape juice. A wide range of quality assurance parameters were assessed by single ¹H NMR experiments acquired directly from juice. The investigation revealed that conditions and time of storage should be revised and indicated on all labels. The sterilization process of homemade grape juices was efficient, making it possible to store them for long periods without additives. Furthermore, chemometric analysis classified the best commercial grape juices to be similar to homemade grape juices, indicating that this approach can be used to determine the authenticity after adulteration.

Control methods for arc welding power supplies

Welding is one of the most important process of modern industry. Welding technology is used in the manufacture and repair a wide variety of products from different metals and alloys. In this thesis the different aspects of arc welding were discussed, such as stability and control of welding arc, power supplies for arc welding (especially the welding inverters because it is the most modern welding power source). All parameters of power source have influence on the arc parameters and its by-turn influence on quality. The ways of control for arc welding inverter power sources have been considered. Calculations and modeling in Matlab/Simulink were done for PI control method. All parameters of power source have influence on the arc parameters and its by-turn influence on quality.

Simulating the performance of paper machine control

The topic of this thesis is the simulation of a combination of several control and data assimilation methods, meant to be used for controlling the quality of paper in a paper machine. Paper making is a very complex process and the information obtained from the web is sparse. A paper web scanner can only measure a zig zag path on the web. An assimilation method is needed to process estimates for Machine Direction (MD) and Cross Direction (CD) profiles of the web. Quality control is based on these measurements. There is an increasing need for intelligent methods to assist in data assimilation. The target of this thesis is to study how such intelligent assimilation methods are affecting paper web quality. This work is based on a paper web simulator, which has been developed in the TEKES funded MASI NoTes project. The simulator is a valuable tool in comparing different assimilation methods. The thesis contains the comparison of four different assimilation methods. These data assimilation methods are a first order Bayesian model estimator, an ARMA model based on a higher order Bayesian estimator, a Fourier transform based Kalman filter estimator and a simple block estimator. The last one can be considered to be close to current operational methods. From these methods Bayesian, ARMA and Kalman all seem to have advantages over the commercial one. The Kalman and ARMA estimators seems to be best in overall performance.

Customer Driven Order-to-Delivery Process

This thesis was made for a large forest industry company’s business segment. The purpose of the study was to improve the performance of the order-to-delivery process of the business segment. The study proceeded in three phases. The first phase was to define customer expectations in the market. The second phase was to analyse the performance and the operations of the order-to-delivery process, and to define any challenges or problems in serving the customers. The third and final phase was improving the performance of the order-to-delivery process, within the scope defined by the first two phases. The analysis showed that the delivery reliability is an essential but a challenging issue in the case company’s markets. On delivery reliability standpoint, the most challenging factors were the detected information flow distortions within the company as well as in the whole supply chain, and the lack of horizontal control over the multi-stage process.

BimTwin - Two component continuous process hygiene concept

The aim of this study was to examine suitability of BimTwin cleaning concept in card board machine to control microbiological activity and describe microbiological balance of the machine. In a review of literature is examined microbe and spore caused problems in paper industry. Biggest problems are deposits, which decrease runnability and cause quality errors. In this chapter is also introduced most common oxidizing biocides used in paper industry and described ATP assay as a microbiological monitoring method. In an experimental part are included BimTwin mill trial results, chemical condition monitoring methods and microbiological balance in a card board machine. In a second part are examined possibilities to effect hygiene of card board by chemical treatment of the surface size and coating. Result showed that BimTwin concept is suitable for card board machine as a cleaning concept, when chemical dosing is fitted right. For proper dosing and secure tolerable hygiene level, chemical and microbiological monitoring is significant. Determining of the microbiological balance would have need more sampling. According to acquired results, broke turned out to be the biggest microbe source. Sizing and coating experiments showed that it is possible to improve hygiene of card board by chemically treated surface size and coating color.

Analysis of electricity distribution network operation business models and capitalization of control room functions with DMS

Electricity distribution network operation (NO) models are challenged as they are expected to continue to undergo changes during the coming decades in the fairly developed and regulated Nordic electricity market. Network asset managers are to adapt to competitive technoeconomical business models regarding the operation of increasingly intelligent distribution networks. Factors driving the changes for new business models within network operation include: increased investments in distributed automation (DA), regulative frameworks for annual profit limits and quality through outage cost, increasing end-customer demands, climatic changes and increasing use of data system tools, such as Distribution Management System (DMS). The doctoral thesis addresses the questions a) whether there exist conditions and qualifications for competitive markets within electricity distribution network operation and b) if so, identification of limitations and required business mechanisms. This doctoral thesis aims to provide an analytical business framework, primarily for electric utilities, for evaluation and development purposes of dedicated network operation models to meet future market dynamics within network operation. In the thesis, the generic build-up of a business model has been addressed through the use of the strategicbusiness hierarchy levels of mission, vision and strategy for definition of the strategic direction of the business followed by the planning, management and process execution levels of enterprisestrategy execution. Research questions within electricity distribution network operation are addressed at the specified hierarchy levels. The results of the research represent interdisciplinary findings in the areas of electrical engineering and production economics. The main scientific contributions include further development of the extended transaction cost economics (TCE) for government decisions within electricity networks and validation of the usability of the methodology for the electricity distribution industry. Moreover, DMS benefit evaluations in the thesis based on the outage cost calculations propose theoretical maximum benefits of DMS applications equalling roughly 25% of the annual outage costs and 10% of the respective operative costs in the case electric utility. Hence, the annual measurable theoretical benefits from the use of DMS applications are considerable. The theoretical results in the thesis are generally validated by surveys and questionnaires.

Effect of hydrodynamics on modelling, monitoring and control of crystallization

Crystallization is a purification method used to obtain crystalline product of a certain crystal size. It is one of the oldest industrial unit processes and commonly used in modern industry due to its good purification capability from rather impure solutions with reasonably low energy consumption. However, the process is extremely challenging to model and control because it involves inhomogeneous mixing and many simultaneous phenomena such as nucleation, crystal growth and agglomeration. All these phenomena are dependent on supersaturation, i.e. the difference between actual liquid phase concentration and solubility. Homogeneous mass and heat transfer in the crystallizer would greatly simplify modelling and control of crystallization processes, such conditions are, however, not the reality, especially in industrial scale processes. Consequently, the hydrodynamics of crystallizers, i.e. the combination of mixing, feed and product removal flows, and recycling of the suspension, needs to be thoroughly investigated. Understanding of hydrodynamics is important in crystallization, especially inlargerscale equipment where uniform flow conditions are difficult to attain. It is also important to understand different size scales of mixing; micro-, meso- and macromixing. Fast processes, like nucleation and chemical reactions, are typically highly dependent on micro- and mesomixing but macromixing, which equalizes the concentrations of all the species within the entire crystallizer, cannot be disregarded. This study investigates the influence of hydrodynamics on crystallization processes. Modelling of crystallizers with the mixed suspension mixed product removal (MSMPR) theory (ideal mixing), computational fluid dynamics (CFD), and a compartmental multiblock model is compared. The importance of proper verification of CFD and multiblock models is demonstrated. In addition, the influence of different hydrodynamic conditions on reactive crystallization process control is studied. Finally, the effect of extreme local supersaturation is studied using power ultrasound to initiate nucleation. The present work shows that mixing and chemical feeding conditions clearly affect induction time and cluster formation, nucleation, growth kinetics, and agglomeration. Consequently, the properties of crystalline end products, e.g. crystal size and crystal habit, can be influenced by management of mixing and feeding conditions. Impurities may have varying impacts on crystallization processes. As an example, manganese ions were shown to replace magnesium ions in the crystal lattice of magnesium sulphate heptahydrate, increasing the crystal growth rate significantly, whereas sodium ions showed no interaction at all. Modelling of continuous crystallization based on MSMPR theory showed that the model is feasible in a small laboratoryscale crystallizer, whereas in larger pilot- and industrial-scale crystallizers hydrodynamic effects should be taken into account. For that reason, CFD and multiblock modelling are shown to be effective tools for modelling crystallization with inhomogeneous mixing. The present work shows also that selection of the measurement point, or points in the case of multiprobe systems, is crucial when process analytical technology (PAT) is used to control larger scale crystallization. The thesis concludes by describing how control of local supersaturation by highly localized ultrasound was successfully applied to induce nucleation and to control polymorphism in reactive crystallization of L-glutamic acid.