Sorption kinetics and intrapaticulate diffusivity of As(III) bioremediation from aqueous solution, using modified and unmodified coconut fiber

The pollution and toxicity problems posed by arsenic in the environment have long been established. Hence, the removal and recovery remedies have been sought, bearing in mind the efficiency, cost effectiveness and environmental friendliness of the methods employed. The sorption kinetics and intraparticulate diffusivity of As (III) bioremediation from aqueous solution using modified and unmodified coconut fiber was investigated. The amount adsorbed increased as time increased, reaching equilibrium at about 60 minutes. The kinetic studies showed that the sorption rates could be described by both pseudo-first order and pseudo-second order process with the later showing a better fit with a value of rate constant of 1.16 x 10-4 min-1 for the three adsorbent types. The mechanism of sorption was found to be particle diffusion controlled. The diffusion and boundary layer effects were also investigation. Therefore, the results show that coconut fiber, both modified and unmodified is an efficient sorbent for the removal of As (III) from industrial effluents with particle diffusion as the predominant mechanism.

Adsorptive removal of harmful organic compound from aqueous solutions

Adsorption is one of the most commonly used methods in water treatment processes. It is attractive due to it easy operation and the availability of a wide variety of commercial adsorbents. This doctoral thesis focuses on investigating and explaining the influence of external phase conditions (temperature, pH, ionic strength, acidity, presence of cosolutes) on adsorption phenomena. In order to cover a wide range of factors and phenomena, case studies were chosen from various fields where adsorption is applied. These include the adsorptive removal of surface active agents (used in cleaning chemicals, for example) from aqueous effluents, the removal of hormones (estradiol) from drinking water, and the adsorption of antibiotics onto silica. The latter can beused to predict the diffusion of antibiotics in the aquatic system if they are released into the environment. Also the adsorption of living cells on functionalized polymers to purify infected water streams was studied. In addition to these examples, the adsorptive separation of harmful compounds from internal water streams within a chemical process was investigated. The model system was removal of fermentation inhibitors from lignocelluloses hydrolyzates. The detoxification of the fermentation broth is an important step in the manufacture of bioethanol from wood, but has not been studied previously in connection with concentrated acid hydrolyzates. New knowledge on adsorption phenomena was generated for all of the applications investigated. In most cases, the results could be explained by combining classical theories for individual phenomena. As an example, it was demonstrated how liquid phase aggregation could explain abnormal-looking adsorption equilibrium data. In addition to the fundamental phenomena, also process performance was of interest. This aspect is often neglected in adsorption studies. It was demonstrated that adsorbents should not be selected for a target application based on their adsorption properties only, but regeneration of the spent adsorbent must be considered. It was found that using a suitable amount of organic co-solvent in the regeneration can significantly improve the productivity of the process.

Assessment of endocrine disrupting activities in the aquatic environment

Hormonstörande ämnen är syntetiska eller naturliga ämnen som stör organismers hormonsystem och bidrar till könsförvirring och sterilitet. Sådana ämnen kommer i ökande takt ut i vattenmiljön genom rester av läkemedel, bekämpningsmedel och industriprodukter. Eftersom det finns många likheter mellan hormonsystemen hos människan och övriga ryggradsdjur kan till exempel fiskar användas som modellsystem för att underöka detta problem. I tidigare undersökningar har man funnit hormonella störningar, bl.a. feminisering och maskulinisering hos fiskar som utsatts för avfallsvatten från kommunala reningsverk eller avfallsvatten från pappersindustrin. Målet med denna avhandling var att undersöka om renat avfallsvatten från kommunala reningsverk längs Finlands kust innehåller hormonstörande ämnen i sådana mängder att de kan försorsaka hormonstörande effekter på fisk. Målet i denna avhandling var också att utveckla cellulära testsystem baserade på fiskceller, eftersom behovet av tillförlitliga och kostnadseffektiva cellbaserade tester för att underlätta riskbedömningen av hormonstörande ämnen är mycket stort för tillfället. Som testsystem har storspiggen använts, som besitter flera användbara biomarkörer för att mäta hormonstörande ämnens påverkan. Resultaten tyder på att problemen med hormonstörande påverkan på fisk inte är lika utbredda i Finland som i många andra europeiska länder. Detta beror troligtvis på att finska reningsverk har effektiva reningstekniker som reducerar mängden hormonstörande ämnen, eller på att utspädningen av avloppen i recipienterna är större än i många andra länder. Dock kan problemen inte helt uteslutas eftersom vissa feminiserande (estrogena) effekter kunde observeras hos fisken i de undersökta recipienterna utanför kommunala reningsverk. I kontrollerade laboratorieförsök där storpsiggar exponerades för kommunalt avloppsvatten uppmättes även här effekter som tyder på förekomst av estrogener i avloppsvattnet. De cell-baserade testsystemen klarade av att förutspå hormonella effekter hos hel fisk och kan därför vara mycket användbara i fortsatta studier av hormonstörande ämnens verkningsmekanismer i preliminära toxicitetsbedömningar.

Recovery of carboxylic acids from aqueous solutions

Carboxylic acids are commonly used organic acids and have many applications in industries producing food and pharmaceutical products, surfactants and detergents. Especially formic, acetic, propionic and butyric acid are important organic chemicals. These compounds can be found in many side streams and plant effluents. Recovery costs of carboxylic acids are high when they are removed from dilute solution. Conventional processes for the recovery of carboxylic acids from aqueous solutions are classical distillation or extractive distillation, azeotropic distillation or liquid-liquid extraction. The literature part of this Master’s of Science Thesis comprises possible extractants in liquid-liquid extraction of carboxylic acids from aqueous solutions and methods for their regeneration form the extract. The experimental part of this Thesis investigates liquid-liquid extraction of carboxylic acids from aqueous solutions. The aim of this work was to find a suitable extractant for liquid-liquid extraction and suitable process conditions to recover carboxylic acids from aqueous solutions. Also, back extraction of carboxylic acids and their thermal decomposition in relation to distillation of were. Experiments showed that there is more than one possible extractant for liquid-liquid extraction of carboxylic acids. Results also showed that it is possible to separate carboxylic acids and regenerate all the used extractants by vacuum distillation at suitable temperature.

Loviisan ydinvoimalaitoksen todennäköisyyspohjaisen riskianalyysin tason 2 epävarmuustarkastelut

Diplomityössä tarkastellaan Loviisan ydinvoimalaitoksen todennäköisyyspohjaisen riskianalyysin tason 2 epävarmuuksia. Tason 2 riskitutkimuksissa tutkitaan ydinvoimalaitosonnettomuuksia, joiden seurauksena osa reaktorin radioaktiivisista aineista vapautuu ympäristöön. Näiden tutkimuksien päätulos on suuren päästön vuotuinen taajuus ja se on pääosin todelliseen laitoshistoriaan perustuva tilastollinen odotusarvo. Tämän odotusarvon uskottavuutta voidaan parantaa huomioimalla merkittävimmät laskentaan liittyvät epävarmuudet. Epävarmuuksia laskentaan aiheutuu muiden muassa vakavan reaktorionnettomuuden ilmiöistä, turvallisuusjärjestelmien laitteista, inhimillisistä toiminnoista sekä luotettavuusmallin määrittelemättömistä osista. Diplomityössä kuvataan, kuinka epävarmuustarkastelut integroidaan osaksi Loviisan ydinvoimalaitoksen todennäköisyyspohjaisia riskianalyysejä. Tämä toteutetaan diplomityössä kehitetyillä apuohjelmilla PRALA:lla ja PRATU:lla, joiden avulla voidaan lisätä laitoshistorian perusteella muodostetut epävarmuusparametrit osaksi riskianalyysien luotettavuusdataa. Lisäksi diplomityössä on laskettu laskentaesimerkkinä Loviisan ydinvoimalaitoksen suuren päästön vuotuisen taajuuden vaihtelua kuvaava luottamusväli. Tämä laskentaesimerkki pohjautuu pääosin konservatiivisiin epävarmuusarvioihin, ei todellisiin tilastollisiin epävarmuuksiin. Laskentaesimerkin tulosten perusteella Loviisan suuren päästön taajuudella on laaja vaihteluväli; virhekertoimeksi saatiin 8,4 nykyisillä epävarmuusparametreilla. Suuren päästön taajuuden luottamusväliä voidaan kuitenkin tulevaisuudessa supistaa, kun hyödynnetään todelliseen laitoshistoriaan perustuvia epävarmuusparametreja.

Kehittyneiden ydinpolttoainekiertojen ympäristövaikutusten ja taloudellisuuden arviointia

Kaikkein yleisin käytössä oleva ydinpolttoainekierto on nykyisin avoin, jossa käytetty ydinpolttoaine loppusijoitetaan suoraan ilman jälleenkäsittelyä. Nykyisin kehitteillä olevat uuden sukupolven ydinreaktorit ovat kuitenkin pääosin suunniteltu osittain tai kokonaan suljetuille ydinpolttoainekierroille, jossa käytetty polttoaine jälleenkäsitellään ja osa materiaaleista kierrätetään. Tämän työn tavoitteena oli arvioida näitä kehittyneitä ydinpolttoainekiertoja ympäristövaikutusten ja taloudellisuuden suhteen. Työn yleisluonteista vertailua varten valittiin neljä erilaista kehittynyttä polttoainekiertoskenaariota, joita verrattiin avoimeen polttoainekiertoon erilaisten parametrien avulla. Parametreinä käytettiin muun muassa uraanin kulutusta, loppusijoitettavan jätteen määrää, aktiivisuutta ja lämmöntuottoa sekä käytönaikaisten radioaktiivisten päästöjen määrää. Yleislounteisen arvioinnin lisäksi työssä tarkasteltiin polttoainekiertoa myös Suomen näkökulmasta. Nykyistä polttoainekiertoa verrattiin kahteen erilaiseen tulevaisuuden versioon. Kestävän kehityksen osalta kehittyneet polttoainekierrot vähensivät ympäristövaikutusten määrää avoimeen polttoainekiertoon verrattuna. Kehittyneiden polttoainekiertojen kustannukset olivat avoimen polttoainekierron kustannuksia suuremmat. Kokonaiskustannuksissa ero oli kaikilla vertailuskenaarioilla alle 20 %, mutta polttoainekiertokustannuksissa kustannusten kasvu oli välillä 27-45 % riippuen skenaariosta. Suomen tapauksessa tulokset olivat hyvin samankaltaisia. Uraanin kulutus ja loppusijoitettavan jätteen määrä väheni kehittyneempien polttoainekiertojen johdosta. Polttoainekiertokustannukset nousivat noin puolitoistakertaisiksi, mutta vaikutus kokonaiskustannuksiin oli vain noin 10 %. Johtopäätöksenä voidaan todeta, ettäydinpolttoainekierron ympäristövaikutuksia on mahdollista vähentää osittain tai kokonaan suljettujen polttoainekiertojen avulla. Vaikka polttoainekierron kustannukset kasvavat, niiden vaikutus ydinsähkön kokonaiskustannuksiin ei ole niin merkittävä.

Start-up of horizontal anaerobic reactors with sludge blanket and fixed bed for wastewater treatment from coffee processing by wet method

In this study it was evaluated the start-up procedures of anaerobic treatment system with three horizontal anaerobic reactors (R1, R2 and R3), installed in series, with volume of 1.2 L each. R1 had sludge blanket, and R2 and R3 had half supporter of bamboo and coconut fiber, respectively. As an affluent, it was synthesized wastewater from mechanical pulping of the coffee fruit by wet method, with a mean value of total chemical oxygen demand (CODtotal) of 16,003 mg L-1. The hydraulic retention time (HRT) in each reactor was 30 h. The volumetric organic loading (VOL) applied in R1 varied from 8.9 to 25.0 g of CODtotal (L d)-1. The mean removal efficiencies of CODtotal varied from 43 to 97% in the treatment system (R1+R2+R3), stabilizing above 80% after 30 days of operation. The mean content of methane in the biogas were of 70 to 76%, the mean volumetric production was 1.7 L CH4 (L reactor d)-1 in the system, and the higher conversions were around at 0.20 L CH4 (g CODremoved)-1 in R1 and R2. The mean values of pH in the effluents ranged from 6.8 to 8.3 and the mean values of total volatile acids remained below 200 mg L-1 in the effluent of R3. The concentrations of total phenols of the affluent ranged from 45 to 278 mg L-1, and the mean removal efficiency was of 52%. The start-up of the anaerobic treatment system occurred after 30 days of operation as a result of inoculation with anaerobic sludge with active microbiota.

Swine manure post-treatment technologies for pathogenic organism inactivation

Swine manure agricultural use is a common practice in Brazil. Their physic-chemical characteristics favor its use as biofertilizer, but the presence of pathogens may become a risk to human health. This research presents a qualitative study of the main alternatives of pig manure disinfection, analyzing efficiency, advantages and limitations of each procedure. The disinfection studies reported in literature are based on the following treatments: alkaline, thermal, biological, chemical, and physical. The greater efficiencies are in thermal treatment (> 4 log: 60 °C), chemical treatment (3 to 4 log: 30mg Cl- L-1; 3 to 4 log: 40 mg O3 L-1) and physical treatment (3 a 4 log: 220 mJ UV radiation cm-2). The biological treatment (anaerobiosis) also promotes the pathogen reduction of swine manure, however with lower efficiency (1 to 2 log). The selection of the treatment should consider: implementation and operation cost, necessity of preliminary treatment, efficiency obtained and destination of the treated manure (agricultural use, water reuse). Brazilian regulation does not have specific guidelines for the microbiological quality of animal production effluents that is very important to be considered due to confined animal feeding operation transformation in the last years in the country.

Shewhart's control charts and process capability ratio applied to a sewage treatment station

The current study used statistical methods of quality control to evaluate the performance of a sewage treatment station. The concerned station is located in Cascavel city, Paraná State. The evaluated parameters were hydrogenionic potential, settleable solids, total suspended solids, chemical oxygen demand and biochemical oxygen demand in five days. Statistical analysis was performed through Shewhart control charts and process capability ratio. According to Shewhart charts, only the BOD(5.20) variable was under statistical control. Through capability ratios, we observed that except for pH the sewage treatment station is not capable to produce effluents under characteristics that fulfill specifications or standard launching required by environmental legislation.

Soil physical attributes in chemigated banana plantation with wastewater

ABSTRACT The feasibility of using sewage wastewater as a water and nutrient source for plants is an alternative to harness agricultural natural resource, observing its influence on the organic matter dynamics and soil energy. Our objective here was to evaluate the effects of applying different doses of effluent from a sewage treatment plant, in Janaúba – MG, Brazil, over the physical attributes of a soil grown with “Prata Anã” banana. From soil sample collection at depths of 0-20, 20-40, and 40-60 cm, we determined the following soil properties: soil density, total porosity, macroporosity, microporosity, organic matter, clay dispersed in water and stability of soil aggregate. The experimental design was in randomized blocks with four repetitions. Wastewater raising doses promoted increase in suspended solids, contributing to macroporosity reduction at 20-40 and 40-60 cm depths; as well as a reduction in organic matter within 0-20 cm layer. Clay dispersal was observed in the depths of 0-20 cm, being derived from an increase in sodium content. Concurrently, there was a reduction of soil aggregate stability.

HYDROPHOBIC MEMBRANE TECHNOLOGY FOR AMMONIA EXTRACTION FROM WASTEWATERS

ABSTRACT Total Ammoniacal Nitrogen - TAN (NH3 + NH4+) in wastewaters cause environmental degradation concerns due to their negative impacts on air, soil and water. Several technologies are available for TAN removal from the wastewaters. One emerging technology is the use of hydrophobic membrane as non-destructive NH3 extraction. In this paper the authors discuss the uses of gas permeable membrane (GPM) and its physicochemical characteristics that influence gas mass transfer rate, diffusion and recovery mechanisms of NH3 from liquid sources (e.g. animal wastewater). Several aspects of NH3 extraction from liquid manure and other TAN generation sources using GPM technology as well as its applicability for NH3 mitigation from liquid effluents and possible recovery as a nutrient for plant growth are also discussed in this review.

Electrocoagulation in the treatment of industrial waters and wastewaters

Chemical coagulation is commonly used in raw water and wastewater treatment plants for the destabilisation of pollutants so that they can be removed in the subsequent separation processes. The most commonly used coagulation chemicals are aluminium and iron metal salts. Electrocoagulation technology has also been proposed for the treatment of raw waters and wastewaters. With this technology, metal cations are produced on the electrodes via electrolysis and these cations form various hydroxides in the water depending on the water pH. In addition to this main reaction, several side reactions, such as hydrogen bubble formation and the reduction of metals on cathodes, also take place in the cell. In this research, the applications of electrocoagulation were investigated in raw water treatment and wastewater applications. The surface water used in this research contained high concentrations of natural organic matter (NOM). The effect of the main parameters – current density, initial pH, electric charge per volume, temperature and electrolysis cell construction – on NOM removal were investigated. In the wastewater treatment studies, the removal of malodorous sulphides and toxic compounds from the wastewaters and debarking effluents were studied. Also, the main parameters of the treatment, such as initial pH and current density, were investigated. Aluminium electrodes were selected for the raw water treatment, whereas wastewaters and debarking effluent were treated with iron electrodes. According to results of this study, aluminium is more suitable electrode material for electrocoagulation applications because it produces Al(III) species. Metal ions and hydroxides produced by iron electrodes are less effective in the destabilisation of pollutants because iron electrodes produce more soluble and less charged Fe(II) species. However, Fe(II) can be effective in some special applications, such as sulphide removal. The resulting metal concentration is the main parameter affecting destabilisation of pollutants. Current density, treatment time, temperature and electrolysis cell construction affect the dissolution of electrodes and hence also the removal of pollutants. However, it seems that these parameters have minimal significance in the destabilization of the pollutants besides this effect (in the studied range of parameters). Initial pH and final pH have an effect on the dissolution of electrodes, but they also define what aluminium or iron species are formed in the solution and have an effect on the ζ-potential of all charged species in the solution. According to the results of this study, destabilisation mechanisms of pollutants by electrocoagulation and chemical coagulation are similar. Optimum DOC removal and low residual aluminium can be obtained simultaneously with electrocoagulation, which may be a significant benefit of electrocoagulation in surface water treatment compared to chemical coagulation. Surface water treatment with electrocoagulation can produce high quality water, which could be used as potable water or fresh water for industrial applications. In wastewater treatment applications, electrocoagulation can be used to precipitate malodorous sulphides to prevent their release into air. Technology seems to be able to remove some toxic pollutants from wastewater and could be used as pretreatment prior to treatment at a biological wastewater treatment plant. However, a thorough economic and ecological comparison of chemical coagulation and electrocoagulation is recommended, because these methods seem to be similar in pollutant destabilisation mechanisms, metal consumption and removal efficiency in most applications.

Application of capillary electrophoretic methods for determining carbohydrates and aliphatic carboxylic acids formed during wood processing

Knowledge of the behaviour of cellulose, hemicelluloses, and lignin during wood and pulp processing is essential for understanding and controlling the processes. Determination of monosaccharide composition gives information about the structural polysaccharide composition of wood material and helps when determining the quality of fibrous products. In addition, monitoring of the acidic degradation products gives information of the extent of degradation of lignin and polysaccharides. This work describes two capillary electrophoretic methods developed for the analysis of monosaccharides and for the determination of aliphatic carboxylic acids from alkaline oxidation solutions of lignin and wood. Capillary electrophoresis (CE), in its many variants is an alternative separation technique to chromatographic methods. In capillary zone electrophoresis (CZE) the fused silica capillary is filled with an electrolyte solution. An applied voltage generates a field across the capillary. The movement of the ions under electric field is based on the charge and hydrodynamic radius of ions. Carbohydrates contain hydroxyl groups that are ionised only in strongly alkaline conditions. After ionisation, the structures are suitable for electrophoretic analysis and identification through either indirect UV detection or electrochemical detection. The current work presents a new capillary zone electrophoretic method, relying on in-capillary reaction and direct UV detection at the wavelength of 270 nm. The method has been used for the simultaneous separation of neutral carbohydrates, including mono- and disaccharides and sugar alcohols. The in-capillary reaction produces negatively charged and UV-absorbing compounds. The optimised method was applied to real samples. The methodology is fast since no other sample preparation, except dilution, is required. A new method for aliphatic carboxylic acids in highly alkaline process liquids was developed. The goal was to develop a method for the simultaneous analysis of the dicarboxylic acids, hydroxy acids and volatile acids that are oxidation and degradation products of lignin and wood polysaccharides. The CZE method was applied to three process cases. First, the fate of lignin under alkaline oxidation conditions was monitored by determining the level of carboxylic acids from process solutions. In the second application, the degradation of spruce wood using alkaline and catalysed alkaline oxidation were compared by determining carboxylic acids from the process solutions. In addition, the effectiveness of membrane filtration and preparative liquid chromatography in the enrichment of hydroxy acids from black liquor was evaluated, by analysing the effluents with capillary electrophoresis.

DFMA Aspects in the Design of a Transfer Line for Off-line Ion Sources

In this thesis, the DFMA is presented and used for the purpose of having a design for a vertical transfer line that can be easily manufactured and assembled. The design of the transfer line, the major components and drawings are presented. The ease of assembly, the costs of manufacturing and differences between the use of steel structure and aluminum are compared. The ALARA principle is followed to minimize the risk of radiation exposure by the means of locating the test ion sources outside the radioactive area.

Identification and application of bile metabolites to assess the exposure of fish to pharmaceuticals in the environment

Thousands of tons of pharmaceuticals are consumed yearly worldwide. Due to the continuous and increasing consumption and their incomplete elimination in wastewater treatment plants (WWTP), pharmaceuticals and their metabolites can be detected in receiving waters, although at low concentrations (ng to low μg/L). As bioactive molecules the presence of pharmaceuticals in the aquatic environment must be considered potentially hazardous for the aquatic organisms. In this thesis, the biotransformation and excretion of pharmaceuticals in fish was studied. The main biotransformation pathways of three anti‐inflammatory drugs, diclofenac, naproxen and ibuprofen, in rainbow trout were glucuronidation and taurine conjugation of the parent compounds and their phase I metabolites. The same metabolites were present in fish bile in aquatic exposures as in fish dosed with intraperitoneal injection. Higher bioconcentration factor in bile (BCFbile) was found for ibuprofen when compared to diclofenac and naproxen. Laboratory exposure studies were followed by a study of uptake of pharmaceuticals in a wild fish population living in lake contaminated with WWTP effluents. Of the analyzed 17 pharmaceuticals and six phase I metabolites, only diclofenac, naproxen and ibuprofen was present in bream and roach bile. It was shown, that diclofenac, naproxen and ibuprofen excreted by the liver can be found in rainbow trout and in two native fish species living in the receiving waters. In the bream and roach bile, the concentrations of diclofenac, naproxen and ibuprofen were roughly 1000 times higher than those found in the lake water, while in the laboratory exposures, the bioconcentration of the compounds and their metabolites in rainbow trout bile were at the same level as in wild fish or an order of magnitude higher. Thus, the parent compounds and their metabolites in fish bile can be used as a reliable biomarker to monitor the exposure of fish to environmental pharmaceuticals present in water receiving discharges from WWTPs.