Estudo de viabilidade técnico-ambiental para implantação de parques eólicos: um estudo de caso em um fragmento do litoral setentrional do Rio Grande do Norte/Brasil

The use of energy from renewable sources is increasingly demanded by society, especially aeolian - whose raw material is wind. Investments in wind power have become significant in Brazil with emphasis on the Northeast and in particular the Rio Grande do Norte state. According to the Empresa de Pesquisa Energética (Energy Research Company) (2012 ) , investments in the state grew significantly since 2002 with a total accumulated power, by 2013, of approximately 3,400 MW . Even with the early experiences of exploitation of wind energy in 2002, it is still considered new and requires further study referring to the likely changes in the environment and society. In this case, it is of growing and urgent importance to deeply study the wind still in the survey phase of the project, ie , at the beginning of decision making on the most feasible to implement these parks site. Given the above, the question is: from a technical and environmental analysis, how to identify viable areas to install Aeolian parks, taking into account the factors of the environmental dynamics that are relevant to minimize the negative results to the environment and the society? Thus, this study conducted a study on technical and environmental feasibility, proposing a methodology of exploration of feasible wind farms in coastal areas. The study area was a fragment of the northern coast of Rio Grande do Norte and its natural landscape units were identified through the environmental characterization of the area, as well as it was elaborated the map of the land cover, restriction homes and urban areas and Permanent Preservation Areas - PPAs. The environmental fragility was subdivided in the fragility of the natural dynamic, mapped through relief, soils and geology of natural units, and the fragility of the ecosystem, originated by the land cover map. In addition to these maps, it was generated the wind resource for an area from a height of 50 and 100 meters. The intersection between the fragility maps, PPAs and Restriction of homes superimposed on maps of wind potential, provided the map of feasibility of Aeolian parks, resulting in the most favorable areas for its facilities in a technical and environmental point of view. From this study, the entrepreneur can evaluate whether or not to proceed with the studies in this area and especially decrease potential conflicts with society.

Estudo e aplicação da transformada de Fourier na regularização de dados sísmicos na exploração de petróleo

In the oil prospection research seismic data are usually irregular and sparsely sampled along the spatial coordinates due to obstacles in placement of geophones. Fourier methods provide a way to make the regularization of seismic data which are efficient if the input data is sampled on a regular grid. However, when these methods are applied to a set of irregularly sampled data, the orthogonality among the Fourier components is broken and the energy of a Fourier component may "leak" to other components, a phenomenon called "spectral leakage". The objective of this research is to study the spectral representation of irregularly sampled data method. In particular, it will be presented the basic structure of representation of the NDFT (nonuniform discrete Fourier transform), study their properties and demonstrate its potential in the processing of the seismic signal. In this way we study the FFT (fast Fourier transform) and the NFFT (nonuniform fast Fourier transform) which rapidly calculate the DFT (discrete Fourier transform) and NDFT. We compare the recovery of the signal using the FFT, DFT and NFFT. We approach the interpolation of seismic trace using the ALFT (antileakage Fourier transform) to overcome the problem of spectral leakage caused by uneven sampling. Applications to synthetic and real data showed that ALFT method works well on complex geology seismic data and suffers little with irregular spatial sampling of the data and edge effects, in addition it is robust and stable with noisy data. However, it is not as efficient as the FFT and its reconstruction is not as good in the case of irregular filling with large holes in the acquisition.

Estudo e aplicação da transformada de Fourier na regularização de dados sísmicos na exploração de petróleo

In the oil prospection research seismic data are usually irregular and sparsely sampled along the spatial coordinates due to obstacles in placement of geophones. Fourier methods provide a way to make the regularization of seismic data which are efficient if the input data is sampled on a regular grid. However, when these methods are applied to a set of irregularly sampled data, the orthogonality among the Fourier components is broken and the energy of a Fourier component may "leak" to other components, a phenomenon called "spectral leakage". The objective of this research is to study the spectral representation of irregularly sampled data method. In particular, it will be presented the basic structure of representation of the NDFT (nonuniform discrete Fourier transform), study their properties and demonstrate its potential in the processing of the seismic signal. In this way we study the FFT (fast Fourier transform) and the NFFT (nonuniform fast Fourier transform) which rapidly calculate the DFT (discrete Fourier transform) and NDFT. We compare the recovery of the signal using the FFT, DFT and NFFT. We approach the interpolation of seismic trace using the ALFT (antileakage Fourier transform) to overcome the problem of spectral leakage caused by uneven sampling. Applications to synthetic and real data showed that ALFT method works well on complex geology seismic data and suffers little with irregular spatial sampling of the data and edge effects, in addition it is robust and stable with noisy data. However, it is not as efficient as the FFT and its reconstruction is not as good in the case of irregular filling with large holes in the acquisition.

Análise comparativa de diferentes configurações de poços no processo de combustão in-situ

With an increasing number of mature fields, heavy oil recovery has performed one of the great challenges of the oil industry. The Brazilian Northeast, for example, has numerous heavy oil reservoirs are explored with the use of thermal methods. Among the types of methods used for heavy oil, there is the method of in-situ combustion, a technique in which heat is produced within the container, unlike the injection of heated fluid when the heat is generated at the surface and transported to the reservoir. In this type of process, it is common to use vertical wells as injectors and producers. However, methods which use horizontal wells like oil producers are increasingly studied because of greater contact area between the formation and combustion front. Thus, the main objective of this work was to study the different configurations of wells (CIS THAITM and CAGD) in the process of in-situ combustion in oil recovery using a semi-synthetic tank with Brazilian Northeast features. The method "toe-to-heel air injection" (THAITM) is a process of enhanced oil recovery, which is the integration of in-situ combustion with technological advances in drilling horizontal wells. This method uses horizontal wells such as oil producers, keeping vertical injection wells for injecting air. The oil drain process by differential gravitational assisted with combustion (CAGD) is an integrated, in this configuration the horizontal injector well is drilled at the top formation with a horizontal production well in the lower section. The simulations were performed in a commercial program of thermal processes, called "STARS" (Steam, Thermal, and Advanced Processes Reservoir Simulator), the company CMG (Computer Modelling Group). An analysis of the air flow injection was performed and it was found that each method had a maximum injection to the base model, a show that through this air injection limit was reduced cumulative production of oil. Analyses of operating parameters were used: injection flow, configuration and completion of wells. In the sensitivity analysis we found that the air injection flow showed greater influence on THAI method, since the CIS method the completion of the wells was the most influential parameter and CAGD configuration wells showed the greatest influence in the recovered fraction. The economic results have shown that the best case obtained in CAGD method because, despite having higher initial cost showed the best financial return compared to the best cases the CIS and THAI.

Análise comparativa de diferentes configurações de poços no processo de combustão in-situ

With an increasing number of mature fields, heavy oil recovery has performed one of the great challenges of the oil industry. The Brazilian Northeast, for example, has numerous heavy oil reservoirs are explored with the use of thermal methods. Among the types of methods used for heavy oil, there is the method of in-situ combustion, a technique in which heat is produced within the container, unlike the injection of heated fluid when the heat is generated at the surface and transported to the reservoir. In this type of process, it is common to use vertical wells as injectors and producers. However, methods which use horizontal wells like oil producers are increasingly studied because of greater contact area between the formation and combustion front. Thus, the main objective of this work was to study the different configurations of wells (CIS THAITM and CAGD) in the process of in-situ combustion in oil recovery using a semi-synthetic tank with Brazilian Northeast features. The method "toe-to-heel air injection" (THAITM) is a process of enhanced oil recovery, which is the integration of in-situ combustion with technological advances in drilling horizontal wells. This method uses horizontal wells such as oil producers, keeping vertical injection wells for injecting air. The oil drain process by differential gravitational assisted with combustion (CAGD) is an integrated, in this configuration the horizontal injector well is drilled at the top formation with a horizontal production well in the lower section. The simulations were performed in a commercial program of thermal processes, called "STARS" (Steam, Thermal, and Advanced Processes Reservoir Simulator), the company CMG (Computer Modelling Group). An analysis of the air flow injection was performed and it was found that each method had a maximum injection to the base model, a show that through this air injection limit was reduced cumulative production of oil. Analyses of operating parameters were used: injection flow, configuration and completion of wells. In the sensitivity analysis we found that the air injection flow showed greater influence on THAI method, since the CIS method the completion of the wells was the most influential parameter and CAGD configuration wells showed the greatest influence in the recovered fraction. The economic results have shown that the best case obtained in CAGD method because, despite having higher initial cost showed the best financial return compared to the best cases the CIS and THAI.

Estudo da eficiência dos adsorventes de Al2O3 e Fe/Al2O3 para remoção de BTX presente em água contaminada com gasolina

Contamination of groundwater by BTX has been featured in recent decades. This type of contamination is due to small and continuous leaks at gas stations, causing serious problems to public health and the environment. Based on these antecedents, the search for new alternatives for treating contaminated water is shown to be essential. Therefore, this study aimed to evaluate the efficiency of removal of BTX by adsorption processes employing commercial alumina (Al2O3) and alumina supported with iron (Fe/Al2O3) as adsorbents. It was prepared by a in a synthetic gasoline solution and distilled water to simulate an actual sample. Initially, the adsorbents were characterized by techniques XRD, TG / DTG, XRF, FTIR and SEM/EDS, several trials, where he was placed synthetic solution to react in the presence of Al2O3 and Fe/Al2O3 in a closed, mechanical stirring system were performed varying the catalyst concentration 2, 4 and 6 g.L-1 every 0, 10, 30 60, 90 and 120 min, aliquots were taken and brought to analysis by gas chromatography flame ionization with headspace extraction. The results indicated that the absorbent which has higher BTX removal capacity was the Fe/Al2O3 at a concentration of 6 g.L-1, pH = 4 and time of 90 minutes reaction, resulting in an efficiency, resulting in a 86,5% efficiency for benzene removal, for the 95,4% toluene, 90,8% for ɱ,ρ- xylene and 93.7% for the θ-xylenes. Subsequently, we performed a kinetic study of the reactions, the values of experimental adsorption capacity (qe) showed agreement with the values of the theoretical adsorption capacity (qc) to the pseudo-second-order model in the adsorption tests using 2 and 6 gL-1 of Al2O3 and assays using 2, 4 and 6 g.L-1 of Fe/Al2O3. A fact corroborated by the R2 values, thus indicating that the chemical interactions are present in the adsorption mechanisms of BTX.

Estudo da injeção de água e gás em um reservatório com características do pré-sal brasileiro

The pre-salt province is composed by large amounts of light oil and with good quality, a reality that puts Brazil in a strategic position facing the great demand for energy worldwide. In this province are the largest discoveries in the world in the last ten years; areas as Libra, Franco and Lula field, everyone containing volumes greater than 8 billion recoverable oil barrels. To develop and optimize the production of these fields, a study was done for choosing the improved oil recovery methods. The main motivations were the presence of carbon dioxide (CO2) as a contaminant and the strategic decision of do not discard it, combined with high GOR (gas-oil ratio) of the reservoir fluid. The method should take advantage of the unique abundant resources: seawater and produced gas. This way, the process of matching these resources in the water alterning gas injection (WAG) became a good option. In this master’s dissertation, it was developed a reservoir model with average characteristics of the Brazilian pre-salt, where was applied the improved oil recovery method of water alternating gas. The production of this reservoir was analyzed by parameters as: the first fluid injected in the injection process, position of the injection wells completion, injection water and gas rate and cycle time. The results showed a good performance of the method, with up to 26% of gains in the recovery factor regarding the primary recovery, since the application of water injection and gas, individually, was not able to overcome 10 % of gain. The most influential parameter found in the results was the cycle time, with higher recovery factor values obtained with the use of shorter times.

Estudo de tensoativos na organofilização de argila bentonítica para uso em fluido de perfuração à base de óleo

Due to the great challenges encountered in drilling wells, there is a need to develop fluids with appropriated properties and able to meet all the requirements of drilling operations. The physicochemical and rheological properties must be carefully controlled so that a fluid can exercise all its functions. In perforations sensitive to contact with water and "offshore", it becomes necessary the use of oil based drilling fluids, but the bentonite clay cannot be used without a previous surface modification so that their surfaces become hydrophobic. Lately, the oil companies in Brazil use imported organoclays in the preparation of oil-based drilling fluids. The study aimed to modify a calcium clay to increase the affinity of the same organic phase of oil-based drilling fluids, applying three surfactants (OCS, CTAB and UTM 150) at different concentrations. The results indicated that the surfactants UTM 150 and CTAB showed better results compared to OCS. Considering the type of surfactant and concentration as variables used in the statistical analysis, the results indicated that only the surface tension and concentration of calcium oxide in response to organophilization process showed statistically significant effects. The organophilizated clay has potential for application in oil-based drilling fluids.

Atividade antiangiogênica da forma recombinante da proteína 21 de Trypanosoma cruzi

Chagas disease, caused by the parasite Trypanosoma cruzi, is the cause of Chronic chagasic cardiomyopathy (CCC). The prospection of innovative therapeutic agents against CCC is a major task. The recombinant form of 21 (rP21), a secreted T. cruzi protein involved in host cell invasion and on progression of chronic inflammatory processes have been studied as a potential novel therapeutic target. Our present work aimed to verify and investigate the impact of rP21 in the formation of blood vessels in vitro and in vivo. First, tEnd cells were treated with different concentrations of rP21 or bacterial extract and viability and cellular adhesion were evaluated by MTT and angiogenesis inhibition by Matrigel tube formation assay and murine model. To verify the proteolytic activity of rP21 on extracellular matrix (ECM) components, fibrinogen, matrigel and fibronectin was incubated with rP21 or not. In addition, we performed proliferation assays and cell cycle analysis. Furthermore, the accumulation and distribution of F-actin was determined by Phalloidin staining using ImageJ software. Finally, tEnd cells were incubated with rP21 and the mRNA levels were analyzed by real-time PCR. Our results showed that rP21 did not alter cell viability and adhesion, but strongly inhibited vessel formation in vitro and in vivo. Tube formation assay showed that angiogenesis inhibition was dependent of the CXCR4-rP21 binding. In addition to these results, we observed that the rP21 was able to inhibit cell proliferation and promoted a significant reduction in the number of 4n cells (G2/M phase). Moreover, we found that rP21 significantly increased F-actin levels and this protein was able to modulate expression of genes related to angiogenesis and actin cytoskeleton. However, rP21 showed no significant activity on the matrix components. In this sense, we conclude that the rP21-endothelial cells (ECs) interaction via CXCR4 promotes inhibition of vessel formation through a cascade of intracellular events, such as inhibition of ECs proliferation and modulation of the expression of molecules associated with angiogenic processes and actin cytoskeleton.

Avaliação do impacto das condições de operação na qualidade do sinal : processamento de dados de reflexão sísmica de multicanal

Através do processamento de dados sísmicos convertem-se registos de campo em secções sísmicas com significado geológico, que revelam informações e ajudam a delinear as camadas geológicas do subsolo e identificar estruturas soterradas. Portanto, a interpretação dos dados sísmicos só é boa se o processamento também o for. Este trabalho é resultado de um estágio curricular na empresa de prospecção geofísica GeoSurveys, que consistiu principalmente em processar 18 linhas de dados de sísmica de reflexão multicanal de alta resolução adquiridas na ilha de Pulau Tekong em Singapura, que têm como finalidade investigação do solo da baia desta mesma ilha. Estes dados foram cedidos à GeoSurveys para fins académicos, caso em que se inclui esta dissertação. Para atingir os objectivos propostos que consistiam em avaliar o impacto das condições de operação na qualidade do sinal sísmico e interpretação das linhas, fez-se o processamento das linhas utilizando um fluxo processamento padrão utilizado na empresa, com recurso ao software Radex Pro. Este fluxo de processamento tem como mais-valia o método de correcções estáticas, o UHRS trim statics, além das técnicas habituais utilizadas para melhorar a resolução das secções sísmicas como é o caso da desconvolução, a atenuação de ruído através do stacking, correcções de NMO, e migração, entre outras técnicas. A interpretação das linhas sísmicas processadas foi feita no software Kingdom Suite (IHS), através da distinção da configuração interna dos reflectores em cada secção sísmica, estabelecendo deste modo as principais unidades sismo-estratigráficas e identificando as zonas de interface que delimitam os horizontes principais. Foi feito ainda um estudo geológico sumário da área de pesquisa e da evolução geodinâmica da região.

Desenvolvimento de um método para correção de curvas de desempenho em bombas centrífugas submersas operando com fluidos viscosos

Electrical Submersible Pump (ESP) is used as an artificial lift technique. However, pumping viscous oil is generally associated with low Reynolds number flows. This condition leads to a performance degradation respect to the performance expected from the regular operation with water that most of the centrifugal pumps are originally designed for. These issues are considered in this investigation through a numerical study of the flow in two different multistage, semi-axial type ESPs. This investigation is carried out numerically using a Computational Fluid Dynamics (CFD) package, where the transient RANS equations are solved numerically. The turbulence is modeled using the SST model. Head curves for several operating conditions are compared with manufacturer’s curves and experimental data for a three-stage ESP, showing good agreement for a wide range of fluid viscosities and rotational speeds. Dimensionless numbers (n, n, n e Re) are used to investigate performance degradation of the ESPs. In addition, flow phenomena through the impellers of the ESPs are investigated using flow field from numerical results. Results show that performance degradation is directly related to rotational Reynolds number, Re. In addition, it was verified that performance degradation occurs for constant normalized specific speedn, which shows that performance degradation occurs similarly for different centrifugal pumps. Moreover, experimental data and numerical results agreed with a correlation from literature between head and flow correction factors proposed by Stepanoff (1967). A definition of modified Reynolds number was proposed and relates the head correction factor to viscosity. A correlation between head correction factor and the modified Reynolds number was proposed, which agreed well with numerical and experimental data. Then, a method to predict performance degradation based on the previous correlations was proposed. This method was compared with others from literature. In general, results and conclusions from this work can also be useful to bring more information about the flow of highly viscous fluids in pumps, especially in semi-axial, multistage ESPs.

Propuestas de formulación de un plan de desarrollo participativo para la vereda la cristalina del Municipio de Puerto Gaitán Meta que surja de las necesidades planteadas por la comunidad

Tesis (Maestría en Estudios y Gestión del Desarrollo).-- Universidad de La Salle. Maestría en Estudios y Gestión del Desarrollo, 2014

Atividade antioxidante e antiproliferativa de extratos de folhas de Plukenetia volubilis L. (EUPHORBIACEAE)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Parâmetros citogenéticos de espécies comerciais de carangidae (perciformes), com vistas a sua empregabilidade na conservação biológica e piscicultura marinha

Worldwide, families Carangidae and Rachycentridae represent one of the groups most important commercial fish, used for food, and great potential for marine aquaculture. However, the genetic bases that can underpin the future cultivation of these species, cytogenetic between these aspects are very weak. The chromosomal patterns have provided basic data for the exploration of biotechnological processes aimed at handling chromosomal genetic improvement, such as induction of polyploidy, androgenesis and ginogenesis, as well as obtaining monosex stocks and interspecific hybridizations. This paper presents a comprehensive cytogenetic survey in 10 species, seven of the family Carangidae and the monotypic family Rachycentridae. Classical cytogenetic analysis and in situ mapping of multigene sequences were employed, and additionally for the genus Selene and morphotypes of Caranx lugubris, comparisons were made using geometric morphometrics. In general, conservative species exhibit a marked chromosome number (2n=48). Although present in large part, different karyotypic form, retain many characteristics typical of chromosomal Order Perciformes, the high number of elements monobrachyal, Ag-NORs/18S rDNA sites and heterochromatin simply reduced, preferably centromeric. The main mechanisms involved in karyotypic diversification are the pericentric inversions, with secondary action of centric fusions. In addition to physical mapping and chromosome detail for the species are presented and discussed patterns of intra-and interspecific diversity, cytotaxonomic markers. This data set provides a better understanding of these patterns caryoevolutyonary groups and conditions for the development of protocols based on Biotechnology for chromosomal manipulation Atlantic these species

Mapeamento cromossômico de genes ribossomais em espécies estuarinas da família Gerreidae Identificação de uniformidade cariotípica e sua empregabilidade com fins biotecnológicos - REPROGEN

Perciformes are dominant in the marine environment, characterized as the largest and most diverse fish group. Some families, as Gerreidae, popularly known as silver jennies, carapebas, or mojarras have a high economic potential to marine fish farming, natural explotation and game fishing. Genetic information of these species are of fundamental importance for their management and production. Despite exist over 13,000 marine fish species described, only 2% were cytogenetically analyzed and less than 1% have some reproductive characteristics known. Induced breeding, cytogenetic characterization and cryopreservation of gametes, represent important areas in applied fish studies. In this project cytogenetic analyzes were performed to acess genetic aspects of Gerreidae species, distributed in coastal and estuarine regions of Northeast Brazil. Different methods for identifying chromosomal regions were employed using conventional techniques (Ag-NORs, C-banding), staining with base-specific fluorochromes (DAPI-CMA3), and physical mapping of ribosomal genes 18S and 5S rDNA, through hybridization in situ with fluorescent probes (FISH). The six species analyzed showed remarkable chromosome conservatism. The 18S and 5S ribosomal genes when analyzed in phylogenetic perspective demonstrate varied evolutionary dynamics, suggesting ocurrence of stasis process in some groups and greater dynamism in others. Double FISH with 18S and 5S probes showed both how efficient cytotaxonomic markers in the homogeneous karyotypes of this group of species. The karyotypic pattern identified in addition to the evolutionary aspects of karyotype, are suggestive of existence of low potential of post-zygotic barrier, prompting further research to prospect for artificial interspecific hybridization of these species of commercial importance