Active sulphide mine tailings impoundments as sources of contaminated drainage: controlling factors, methods of characterisation and geochemical constraints for mitigation

Low quality mine drainage from tailings facilities persists as one of the most significant global environmental concerns related to sulphide mining. Due to the large variation in geological and environmental conditions at mine sites, universal approaches to the management of mine drainage are not always applicable. Instead, site-specific knowledge of the geochemical behaviour of waste materials is required for the design and closure of the facilities. In this thesis, tailings-derived water contamination and factors causing the pollution were investigated in two coeval active sulphide mine sites in Finland: the Hitura Ni mine and the Luikonlahti Cu-Zn-Co-Ni mine and talc processing plant. A hydrogeochemical study was performed to characterise the tailingsderived water pollution at Hitura. Geochemical changes in the Hitura tailings were evaluated with a detailed mineralogical and geochemical investigation (solid-phase speciation, acid mine drainage potential, pore water chemistry) and using a spatial assessment to identify the mechanisms of water contamination. A similar spatial investigation, applying selective extractions, was carried out in the Luikonlahti tailings area for comparative purposes (Hitura low-sulphide tailings vs. Luikonlahti sulphide-rich tailings). At both sites, hydrogeochemistry of tailings seepage waters was further characterised to examine the net results of the processes observed within the impoundments and to identify constraints for water treatment. At Luikonlahti, annual and seasonal variation in effluent quality was evaluated based on a four-year monitoring period. Observations pertinent to future assessment and mine drainage prevention from existing and future tailings facilities were presented based on the results. A combination of hydrogeochemical approaches provided a means to delineate the tailings-derived neutral mine drainage at Hitura. Tailings effluents with elevated Ni, SO₄ ^2- and Fe content had dispersed to the surrounding aquifer through a levelled-out esker and underneath the seepage collection ditches. In future mines, this could be avoided with additional basal liners in tailings impoundments where the permeability of the underlying Quaternary deposits is inadequate, and with sufficiently deep ditches. Based on the studies, extensive sulphide oxidation with subsequent metal release may already initiate during active tailings disposal. The intensity and onset of oxidation depended on e.g. the Fe sulphide content of the tailings, water saturation level, and time of exposure of fresh sulphide grains. Continuous disposal decreased sulphide weathering in the surface of low-sulphide tailings, but oxidation initiated if they were left uncovered after disposal ceased. In the sulphide-rich tailings, delayed burial of the unsaturated tailings had resulted in thick oxidized layers, despite the continuous operation. Sulphide weathering and contaminant release occurred also in the border zones. Based on the results, the prevention of sulphide oxidation should already be considered in the planning of tailings disposal, taking into account the border zones. Moreover, even lowsulphide tailings should be covered without delay after active disposal ceases. The quality of tailings effluents showed wide variation within a single impoundment and between the two different types of tailings facilities assessed. The affecting factors included source materials, the intensity of weathering of tailings and embankment materials along the seepage flow path, inputs from the process waters, the water retention time in tailings, and climatic seasonality. In addition, modifications to the tailings impoundment may markedly change the effluent quality. The wide variation in the tailings effluent quality poses challenges for treatment design. The final decision on water management requires quantification of the spatial and seasonal fluctuation at the site, taking into account changes resulting from the eventual closure of the impoundment. Overall, comprehensive hydrogeochemical mapping was deemed essential in the identification of critical contaminants and their sources at mine sites. Mineralogical analysis, selective extractions, and pore water analysis were a good combination of methods for studying the weathering of tailings and in evaluating metal mobility from the facilities. Selective extractions with visual observations and pH measurements of tailings solids were, nevertheless, adequate in describing the spatial distribution of sulphide oxidation in tailings impoundments. Seepage water chemistry provided additional data on geochemical processes in tailings and was necessary for defining constraints for water treatment.

The Connectivity of Musical Aptitude and Foreign Language Learning Skills: Neural and Behavioural Evidence

Given the structural and acoustical similarities between speech and music, and possible overlapping cerebral structures in speech and music processing, a possible relationship between musical aptitude and linguistic abilities, especially in terms of second language pronunciation skills, was investigated. Moreover, the laterality effect of the mother tongue was examined with both adults and children by means of dichotic listening scores. Finally, two event-related potential studies sought to reveal whether children with advanced second language pronunciation skills and higher general musical aptitude differed from children with less-advanced pronunciation skills and less musical aptitude in accuracy when preattentively processing mistuned triads and music / speech sound durations. The results showed a significant relationship between musical aptitude, English language pronunciation skills, chord discrimination ability, and sound-change-evoked brain activation in response to musical stimuli (durational differences and triad contrasts). Regular music practice may also have a modulatory effect on the brain’s linguistic organization and cause altered hemispheric functioning in those who have regularly practised music for years. Based on the present results, it is proposed that language skills, both in production and discrimination, are interconnected with perceptual musical skills.

Novel Robot Solutions for Carrying out Field Joint Welding and Machining in the Assembly of the Vacuum Vessel of ITER

It is necessary to use highly specialized robots in ITER (International Thermonuclear Experimental Reactor) both in the manufacturing and maintenance of the reactor due to a demanding environment. The sectors of the ITER vacuum vessel (VV) require more stringent tolerances than normally expected for the size of the structure involved. VV consists of nine sectors that are to be welded together. The vacuum vessel has a toroidal chamber structure. The task of the designed robot is to carry the welding apparatus along a path with a stringent tolerance during the assembly operation. In addition to the initial vacuum vessel assembly, after a limited running period, sectors need to be replaced for repair. Mechanisms with closed-loop kinematic chains are used in the design of robots in this work. One version is a purely parallel manipulator and another is a hybrid manipulator where the parallel and serial structures are combined. Traditional industrial robots that generally have the links actuated in series are inherently not very rigid and have poor dynamic performance in high speed and high dynamic loading conditions. Compared with open chain manipulators, parallel manipulators have high stiffness, high accuracy and a high force/torque capacity in a reduced workspace. Parallel manipulators have a mechanical architecture where all of the links are connected to the base and to the end-effector of the robot. The purpose of this thesis is to develop special parallel robots for the assembly, machining and repairing of the VV of the ITER. The process of the assembly and machining of the vacuum vessel needs a special robot. By studying the structure of the vacuum vessel, two novel parallel robots were designed and built; they have six and ten degrees of freedom driven by hydraulic cylinders and electrical servo motors. Kinematic models for the proposed robots were defined and two prototypes built. Experiments for machine cutting and laser welding with the 6-DOF robot were carried out. It was demonstrated that the parallel robots are capable of holding all necessary machining tools and welding end-effectors in all positions accurately and stably inside the vacuum vessel sector. The kinematic models appeared to be complex especially in the case of the 10-DOF robot because of its redundant structure. Multibody dynamics simulations were carried out, ensuring sufficient stiffness during the robot motion. The entire design and testing processes of the robots appeared to be complex tasks due to the high specialization of the manufacturing technology needed in the ITER reactor, while the results demonstrate the applicability of the proposed solutions quite well. The results offer not only devices but also a methodology for the assembly and repair of ITER by means of parallel robots.

Calculation of the carbon footprint of Finnish barley products - methodology and possible applications

The purpose of this thesis was to define how product carbon footprint analysis and its results can be used in company's internal development as well as in customer and interest group guidance, and how these factors are related to corporate social responsibility. From-cradle-to-gate carbon footprint was calculated for three products; Torino Whole grain barley, Torino Pearl barley, and Elovena Barley grit & oat bran, all of them made of Finnish barley. The carbon footprint of the Elovena product was used to determine carbon footprints for industrial kitchen cooked porridge portions. The basic calculation data was collected from several sources. Most of the data originated from Raisio Group's contractual farmers and Raisio Group's cultivation, processing and packaging specialists. Data from national and European literature and database sources was also used. The electricity consumption for porridge portions' carbon footprint calculations was determined with practical measurements. The carbon footprint calculations were conducted according to the ISO 14044 standard, and the PAS 2050 guide was also applied. A consequential functional unit was applied in porridge portions' carbon footprint calculations. Most of the emissions from barley products' life cycle originate from primary production. The nitrous oxide emissions from cultivated soil and the use and production of nitrogenous fertilisers contribute over 50% of products' carbon footprint. Torino Pearl barley has the highest carbon footprint due to the lowest processing output. The reductions in products' carbon footprint can be achieved with developments in cultivation and grain processing. The carbon footprint of porridge portion can be reduced by using domestically produced plant-based ingredients and by making the best possible use of the kettle. Carbon footprint calculation can be used to determine possible improvement points related to corporate environmental responsibility. Several improvement actions are related to economical and social responsibility through better raw material utilization and expense reductions.

The Sottunga-Jurmo shear zone : structure and deformation history of a crustal-scale ductile shear zone in SW Finland

The aim of this study is to gain a better understanding of the structure and the deformation history of a NW-SE trending regional, crustal-scale shear structure in the Åland archipelago, SW Finland, called the Sottunga-Jurmo shear zone (SJSZ). Approaches involving e.g. structural geology, geochronology, geochemistry and metamorphic petrology were utilised in order to reconstruct the overall deformation history of the study area. The study therefore describes several features of the shear zone including structures, kinematics and lithologies within the study area, the ages of the different deformation phases (ductile to brittle) within the shear zone, as well as some geothermobarometric results. The results indicate that the SJSZ outlines a major crustal discontinuity between the extensively migmatized rocks NE of the shear zone and the unmigmatised, amphibolite facies rocks SW of the zone. The main SJSZ shows overall dextral lateral kinematics with a SW-side up vertical component and deformation partitioning into pure shear and simple shear dominated deformation styles that was intensified toward later stages of the deformation history. The deformation partitioning resulted in complex folding and refolding against the SW margin of the SJSZ, including conical and sheath folds, and in a formation of several minor strike-slip shear zones both parallel and conjugate to the main SJSZ in order to accommodate the regional transpressive stresses. Different deformation phases within the study area were dated by SIMS (zircon U-Pb), ID-TIMS (titanite U-Pb) and 40Ar/39Ar (pseudotachylyte wholerock) methods. The first deformation phase within the ca. 1.88 Ga rocks of the study area is dated at ca. 1.85 Ga, and the shear zone was reactivated twice within the ductile regime (at ca. 1.83 Ga and 1.79 Ga), during which the strain was successively increasingly partitioned into the main SJSZ and the minor shear zones. The age determinations suggest that the orogenic processes within the study area did not occur in a temporal continuum; instead, the metamorphic zircon rims and titanites show distinct, 10-20 Ma long breaks in deformation between phases of active deformation. The results of this study further imply slow cooling of the rocks through 600-700ºC so that at 1.79 Ga, 2 the temperature was still at least 600ºC. The highest recorded metamorphic pressures are 6.4-7.1 kbar. At the late stages or soon after the last ductile phase (ca. 1.79 Ga), relatively high-T mylonites and ultramylonites were formed, witnessing extreme deformation partitioning and high strain rates. After the rocks reached lower amphibolite facies to amphibolite-greenschist facies transitional conditions (ca. 500-550ºC), they cooled rapidly, probably due to crustal uplift and exhumation. The shear zone was reactivated at least once within the semi-brittle to brittle regime between ca. 1.79 Ga and 1.58 Ga, as evidenced by cataclasites and pseudotachylytes. In summary, the results of this study suggest that the Sottunga-Jurmo shear zone (and the South Finland shear zone) defines a major crustal discontinuity, and played a central role in accommodating the regional stresses during and after the Svecofennian orogeny.

Detection of beetle damage in forests by X-ray CT image processing

Some beetle species can have devastating economic impacts on forest and nursery industries. A recent example is Anophophora glabripennis, a species of beetle known in the United States as the ''Asian Longhorrned beetle'', which has damaged many American forests, and is a threat which can unintentionally reach south American countries, including Brazil. This work presents a new method based on X-ray computerized tomography (CT) and image processing for beetle injury detection in forests. Its results show a set of images with correct identification of the location of beetles in living trees as well as damage evaluation with time.

PET and MR imaging in Parkinson’s disease patients with cognitive impairment. A study of dopaminergic dysfunction, amyloid deposition, cortical hypometabolism and brain atrophy

Parkinson’s disease (PD) is the second most common neurodegenerative disorder. It is characterized by a severe loss of substantia nigra dopaminergic neurons leading to dopamine depletion in the striatum. PD affects movement, producing motor symptoms such as rigidity, tremor and bradykinesia. Non-motor symptoms include autonomic dysfunction, neurobehavioral problems and cognitive impairment, which may lead to dementia. The pathophysiological basis of cognitive impairment and dementia in PD is unclear. The aim of this thesis was to study the pathophysiological basis of cognitive impairment and dementia in PD. We evaluated the relation between frontostriatal dopaminergic dysfunction and the cognitive symptoms in PD patients with [18F]Fdopa PET. We also combined [C]PIB and [¹⁸F]FDG PET and magnetic resonance imaging in PD patients with and without dementia. In addition, we analysed subregional striatal [¹⁸F]Fdopa PET data to find out whether a simple ratio approach would reliably separate PD patients from healthy controls. The impaired dopaminergic function of the frontostriatal regions was related to the impairment in cognitive functions, such as memory and cognitive processing in PD patients. PD patients with dementia showed an impaired glucose metabolism but not amyloid deposition in the cortical brain regions, and the hypometabolism was associated with the degree of cognitive impairment. PD patients had atrophy, both in the prefrontal cortex and in the hippocampus, and the hippocampal atrophy was related to impaired memory. A single 15-min scan 75 min after a tracer injection seemed to be sufficient for separating patients with PD from healthy controls in a clinical research environment. In conclusion, the occurrence of cognitive impairment and dementia in PD seems to be multifactorial and relates to changes, such as reduced dopaminergic activity, hypometabolism, brain atrophy and rarely to amyloid accumulation.

Neurobiology of pathological gambling. Brain imaging and epidemiological studies

Pathological gambling, a form of behavioral addiction, refers to maladaptive, compulsive gambling behavior severely interfering with an individual’s normal life. The prevalence of pathological gambling has been estimated to be 1–2% in western societies. The reward deficiency hypothesis of addiction assumes that individuals that have, or are prone, to addictions have blunted mesolimbic dopamine reward signaling, which leads to compulsive reward seeking in an attempt to compensate for the malfunctioning brain reward network. In this research project, the effects of gambling were measured using brain [11C] raclopride PET during slot machine gambling and possible brain structural changes associated with pathological gambling using MRI. The subjects included pathological gamblers and healthy volunteers. In addition, impulse control disorders associated with Parkinson’s disease were investigated by using brain [18F]fluorodopa PET and conducting an epidemiological survey. The results demonstrate mesolimbic dopamine release during gambling in both pathological gamblers and healthy volunteers. Striatal dopamine was released irrespective of the gambling outcome, whether the subjects won or not. There was no difference in gambling induced dopamine release between pathological gamblers and control subjects, although the magnitude of the dopamine release correlated with gambling related symptom severity in pathological gamblers. The results also show that pathological gambling is associated with extensive abnormality of brain white matter integrity, as measured with diffusion tensor imaging, similar to substance-addictions. In Parkinson’s disease patients with impulse control disorders, enhanced brain [18F] fluorodopa uptake in the medial orbitofrontal cortex was observed, indicating increased presynaptic monoamine function in this region, which is known to influence signaling in the mesolimbic system and reward processing. Finally, a large epidemiological survey in Finnish Parkinson’s disease patients showed that compulsive behaviors are very common in Parkinson disease and they are strongly associated with depression. These findings demonstrate the role of dopamine in pathological gambling, without support for the concept of reward deficiency syndrome.

Memristive Computing

Memristive computing refers to the utilization of the memristor, the fourth fundamental passive circuit element, in computational tasks. The existence of the memristor was theoretically predicted in 1971 by Leon O. Chua, but experimentally validated only in 2008 by HP Labs. A memristor is essentially a nonvolatile nanoscale programmable resistor — indeed, memory resistor — whose resistance, or memristance to be precise, is changed by applying a voltage across, or current through, the device. Memristive computing is a new area of research, and many of its fundamental questions still remain open. For example, it is yet unclear which applications would benefit the most from the inherent nonlinear dynamics of memristors. In any case, these dynamics should be exploited to allow memristors to perform computation in a natural way instead of attempting to emulate existing technologies such as CMOS logic. Examples of such methods of computation presented in this thesis are memristive stateful logic operations, memristive multiplication based on the translinear principle, and the exploitation of nonlinear dynamics to construct chaotic memristive circuits. This thesis considers memristive computing at various levels of abstraction. The first part of the thesis analyses the physical properties and the current-voltage behaviour of a single device. The middle part presents memristor programming methods, and describes microcircuits for logic and analog operations. The final chapters discuss memristive computing in largescale applications. In particular, cellular neural networks, and associative memory architectures are proposed as applications that significantly benefit from memristive implementation. The work presents several new results on memristor modeling and programming, memristive logic, analog arithmetic operations on memristors, and applications of memristors. The main conclusion of this thesis is that memristive computing will be advantageous in large-scale, highly parallel mixed-mode processing architectures. This can be justified by the following two arguments. First, since processing can be performed directly within memristive memory architectures, the required circuitry, processing time, and possibly also power consumption can be reduced compared to a conventional CMOS implementation. Second, intrachip communication can be naturally implemented by a memristive crossbar structure.

Building organizational creativity – a multitheory and multilevel approach for understanding and stimulating organizational creativity

Organizational creativity is increasingly important for organizations aiming to survive and thrive in complex and unexpectedly changing environments. It is precondition of innovation and a driver of an organization’s performance success. Whereas innovation research increasingly promotes high-involvement and participatory innovation, the models of organizational creativity are still mainly based on an individual-creativity view. Likewise, the definitions of organizational creativity and innovation are somewhat equal, and they are used as interchangeable constructs, while on the other hand they are seen as different constructs. Creativity is seen as generation of novel and useful ideas, whereas innovation is seen as the implementation of these ideas. The research streams of innovation and organizational creativity seem to be advancing somewhat separately, although together they could provide many synergy advantages. Thereby, this study addresses three main research gaps. First, as the knowledge and knowing is being increasingly expertized and distributed in organizations, the conceptualization of organizational creativity needs to face that perspective, rather than relying on the individual-creativity view. Thus, the conceptualization of organizational creativity needs clarification, especially as an organizational-level phenomenon (i.e., creativity by an organization). Second, approaches to consciously build organizational creativity to increase the capacity of an organization to demonstrate novelty in its knowledgeable actions are rare. The current creativity techniques are mainly based on individual-creativity views, and they mainly focus on the occasional problem-solving cases among a limited number of individuals, whereas, the development of collective creativity and creativity by the organization lacks approaches. Third, in terms of organizational creativity as a collective phenomenon, the engagement, contributions, and participation of organizational members into activities of common meaning creation are more important than the individualcreativity skills. Therefore, the development approaches to foster creativity as social, emerging, embodied, and collective creativity are needed to complement the current creativity techniques. To address these gaps, the study takes a multiparadigm perspective to face the following three objectives. The first objective of this study is to clarify and extend the conceptualization of organizational creativity. The second is to study the development of organizational creativity. The third is to explore how an improvisational theater based approach fosters organizational creativity. The study consists of two parts comprising the introductory part (part I) and six publications (part II). Each publication addresses the research questions of the thesis through detailed subquestions. The study makes three main contributions to the research of organizational creativity. First, it contributes toward the conceptualization of organizational creativity by extending the current view of organizational creativity. This study views organizational creativity as a multilevel construct constituting both of individual and collective (group and organizational) creativity. In contrast to current views of organizational creativity, this study bases on organizational (collective) knowledge that is based on and demonstrated through the knowledgeable actions of an organization as a whole. The study defines organizational creativity as an overall ability of an organization to demonstrate novelty in its knowledgeable actions (through what it does and how it does what it does).Second, this study contributes toward the development of organizational creativity as multi-level phenomena, introducing developmental approaches that face two or more of these levels simultaneously. More specifically, the study presents the cross-level approaches to building organizational creativity, by using an approach based in improvisational theater and considering assessment of organizational renewal capability. Third, the study contributes on development of organizational creativity using an improvisational theater based approach as twofold meaning. First, it fosters individual and collective creativity simultaneously and builds space for creativity to occur. Second, it models collective and distributed creativity processes, thereby, contributing to the conceptualization of organizational creativity.

Flexible multibody dynamics and intelligent control of a hydraulically driven hybrid redundant robot machine

The assembly and maintenance of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel (VV) is highly challenging since the tasks performed by the robot involve welding, material handling, and machine cutting from inside the VV. The VV is made of stainless steel, which has poor machinability and tends to work harden very rapidly, and all the machining operations need to be carried out from inside of the ITER VV. A general industrial robot cannot be used due to its poor stiffness in the heavy duty machining process, and this will cause many problems, such as poor surface quality, tool damage, low accuracy. Therefore, one of the most suitable options should be a light weight mobile robot which is able to move around inside of the VV and perform different machining tasks by replacing different cutting tools. Reducing the mass of the robot manipulators offers many advantages: reduced material costs, reduced power consumption, the possibility of using smaller actuators, and a higher payload-to-robot weight ratio. Offsetting these advantages, the lighter weight robot is more flexible, which makes it more difficult to control. To achieve good machining surface quality, the tracking of the end effector must be accurate, and an accurate model for a more flexible robot must be constructed. This thesis studies the dynamics and control of a 10 degree-of-freedom (DOF) redundant hybrid robot (4-DOF serial mechanism and 6-DOF 6-UPS hexapod parallel mechanisms) hydraulically driven with flexible rods under the influence of machining forces. Firstly, the flexibility of the bodies is described using the floating frame of reference method (FFRF). A finite element model (FEM) provided the Craig-Bampton (CB) modes needed for the FFRF. A dynamic model of the system of six closed loop mechanisms was assembled using the constrained Lagrange equations and the Lagrange multiplier method. Subsequently, the reaction forces between the parallel and serial parts were used to study the dynamics of the serial robot. A PID control based on position predictions was implemented independently to control the hydraulic cylinders of the robot. Secondly, in machining, to achieve greater end effector trajectory tracking accuracy for surface quality, a robust control of the actuators for the flexible link has to be deduced. This thesis investigates the intelligent control of a hydraulically driven parallel robot part based on the dynamic model and two schemes of intelligent control for a hydraulically driven parallel mechanism based on the dynamic model: (1) a fuzzy-PID self-tuning controller composed of the conventional PID control and with fuzzy logic, and (2) adaptive neuro-fuzzy inference system-PID (ANFIS-PID) self-tuning of the gains of the PID controller, which are implemented independently to control each hydraulic cylinder of the parallel mechanism based on rod length predictions. The serial component of the hybrid robot can be analyzed using the equilibrium of reaction forces at the universal joint connections of the hexa-element. To achieve precise positional control of the end effector for maximum precision machining, the hydraulic cylinder should be controlled to hold the hexa-element. Thirdly, a finite element approach of multibody systems using the Special Euclidean group SE(3) framework is presented for a parallel mechanism with flexible piston rods under the influence of machining forces. The flexibility of the bodies is described using the nonlinear interpolation method with an exponential map. The equations of motion take the form of a differential algebraic equation on a Lie group, which is solved using a Lie group time integration scheme. The method relies on the local description of motions, so that it provides a singularity-free formulation, and no parameterization of the nodal variables needs to be introduced. The flexible slider constraint is formulated using a Lie group and used for modeling a flexible rod sliding inside a cylinder. The dynamic model of the system of six closed loop mechanisms was assembled using Hamilton’s principle and the Lagrange multiplier method. A linearized hydraulic control system based on rod length predictions was implemented independently to control the hydraulic cylinders. Consequently, the results of the simulations demonstrating the behavior of the robot machine are presented for each case study. In conclusion, this thesis studies the dynamic analysis of a special hybrid (serialparallel) robot for the above-mentioned special task involving the ITER and investigates different control algorithms that can significantly improve machining performance. These analyses and results provide valuable insight into the design and control of the parallel robot with flexible rods.

Management of Soft Information in Sales and Operations Planning

With a Sales and Operations Planning (S&OP) process, a company aims to manage the demand and supply by planning and forecasting. The studied company uses an integrated S&OP process to improve the company's operations. The aim of this thesis is to develop this business process by finding the best possible way to manage the soft information in S&OP, whilst also understanding the importance and types (assumptions, risks and opportunities) of soft information in S&OP. The soft information in S&OP helps to refine future S&OP planning, taking into account the uncertainties that affect the balance of the long-term demand and supply (typically 12-18 months). The literature review was used to create a framework for soft information management process in S&OP. There were not found a concrete way how to manage soft information in the existing literature. In consequence of the poor literature available the Knowledge Management literature was used as the base for the framework creation, which was seen in the very same type of information management like the soft information management is. The framework created a four-stage process to manage soft information in S&OP that included also the required support systems. First phase is collecting and acquiring soft information in S&OP, which include also categorization. The categorization was the cornerstone to identify different requirements that needs to be taken into consideration when managing soft information in S&OP process. The next phase focus on storing data, which purpose is to ensure the soft information is managed in a common system (support system) in a way that the following phase makes it available to users in S&OP who need by help of sharing and applications process. The last phase target is to use the soft information to understand assumptions and thoughts of users behind the numbers in S&OP plans. With this soft management process the support system will have a key role. The support system, like S&OP tool, ensures that soft information is stored in the right places, kept up-to-date and relevancy. The soft information management process in S&OP strives to improve the relevant soft information documenting behind the S&OP plans into the S&OP support system. The process offers an opportunity to individuals to review, comment and evaluate soft information in S&OP made by their own or others. In the case company it was noticed that without a properly documented and distributed soft information in S&OP it was seen to cause mistrust towards the planning.

Comparison of Pavlovian serial conditional discrimination in rats and hamsters in the same experimental situation

The present study compares behavioral changes between two distinct rodent groups, hamsters (Mesocricetus auratus) and Wistar rats, when submitted in the same homogeneous experimental situations to a serial conditional discrimination procedure which involves water deprivation and the processing of temporal variables. Both hamsters and rats acquired serial positive conditional discrimination as indicated by higher frequencies of magazine-oriented behavior during the tone followed by reinforcement (T+) and preceded by the feature stimulus light (L) and during the empty interval, than during the tone alone not followed by reinforcement (T-). Rats' frequencies of magazine-oriented behavior were high during T+ and T-, initially during training, and decreased during T- as the training progressed. However, the hamsters' frequencies of magazine-oriented behavior started very low and increased only during T+ as the training progressed. Comparison of the frequencies of magazine-oriented behavior during the empty interval in relation to the frequencies during the preceding L period showed that rats' frequencies remained very high and hamsters' frequencies increased during training. These results suggest that rats and hamsters have different behavioral strategies for the acquisition of a conditional discrimination. The results of the comparisons made in these experiments support the view of the importance of an ecological psychology approach to the understanding of complex learning in animals.

Antinociceptive potency of aminoglycoside antibiotics and magnesium chloride: a comparative study on models of phasic and incisional pain in rats

A close relationship exists between calcium concentration in the central nervous system and nociceptive processing. Aminoglycoside antibiotics and magnesium interact with N- and P/Q-type voltage-operated calcium channels. In the present study we compare the antinociceptive potency of intrathecal administration of aminoglycoside antibiotics and magnesium chloride in the tail-flick test and on incisional pain in rats, taken as models of phasic and persistent post-surgical pain, respectively. The order of potency in the tail-flick test was gentamicin (ED50 = 3.34 µg; confidence limits 2.65 and 4.2) > streptomycin (5.68 µg; 3.76 and 8.57) = neomycin (9.22 µg; 6.98 and 12.17) > magnesium (19.49 µg; 11.46 and 33.13). The order of potency to reduce incisional pain was gentamicin (ED50 = 2.06 µg; confidence limits 1.46 and 2.9) > streptomycin (47.86 µg; 26.3 and 87.1) = neomycin (83.17 µg; 51.6 and 133.9). The dose-response curves for each test did not deviate significantly from parallelism. We conclude that neomycin and streptomycin are more potent against phasic pain than against persistent pain, whereas gentamicin is equipotent against both types of pain. Magnesium was less potent than the antibiotics and effective in the tail-flick test only.