Preparation and characterization of uniform, spherical particles of Y2O2S and Y2O2S:Eu

The preparation of spherical Y2O2S and Y2O2S:Eu particles using a solid-gas reaction of monodispersed precursors with elemental sulfur vapor under an argon atmosphere has been investigated. The precursors, undoped and doped yttrium basic carbonates, are synthesized by aging a stock solution containing the respective cation chloride and urea at 82-84 °C. Y2O2S and Y2O2S:Eu were characterized in terms of their composition, crystallinity and morphology by chemical analysis, X-ray powder diffraction (XRD), IR spectroscopy, and scanning electron microscopy (SEM). The Eu-doped oxysulfide was also characterized by atomic absorption spectrophotometry and luminescence spectroscopy. The spherical morphology of oxysulfide products and of basic carbonate precursors suggests a topotatic inter-relationship between both compounds.

Preparation and characterization of SrBi2Nb2O9 thin films made by polymeric precursors

A polymeric precursor solution was employed in preparing SrBi2Nb2O9 (SBN) powder and thin films dip coated onto Si(100) substrate. XRD results show that the SBN perovskite phase forms at temperatures as low as 600°C through an intermediate fluorite phase. This fluorite phase is observed for samples heat-treated at temperatures of 400 and 500°C. After heat treatment at temperatures ranging from 300 to 800°C, thin films were shown to be crack free. Grazing incident angle XRD characterization shows the occurrence of the fluorite intermediate phase for films also. The thickness of films, measured by MEV, was in the order of 80-100 nm.

Synthesis and characterization of the mer-[RuCl3(NO)(dppb)] isomer. X-ray structures of fac-[RuCl3(NO)(dppm)], cis-[RuCl2(dppm)2] and mer-[RuCl3(NO)(dppb)] [dppm=1,2-Bis(diphenylphosphino)methane and dppb=1,4-Bis(diphenylphosphino)butane]

The fac-[RuCl3(NO)(dppm)] (1) and cis-[RuCl2(dppm)2] (2) complexes were obtained with co-crystallization in the solid state from the reaction of RuCl3(NO) with the diphosphine in dichloromethane. mer-[RuCl3(NO)(dppb)] (3) was obtained from [RuCl3(dppb)(H2O)] by bubbling NO for 30 min in the same solvent. The crystal and molecular structures of these three compounds have been determined from X-ray studies. © Elsevier Science Ltd.

Preparation and characterization of glass-ceramic materials in the BaO-Li2O-ZrO2-SiO2 system and their dependence on treatment temperatures

The preparation and characterization of transparent glass-ceramics in the composition of 30Li2O:5ZrO2:xBaO:(100-x) SiO2 with x = 0, 5, 10, 15, and 20 mol% are described. Glasses were melted in a platinum crucible at 1100°C for 2 h and then heat-treated at 900°C for 3 h. The characterizations were performed by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman and infrared spectroscopy, and scanning electron microscopy (SEM). The experimental results indicate that there was a structural change in the glass-ceramics as the BaO concentration in the mixture increased. In the XRD patterns of samples without heat treatment, only the halo was observed. After heat treatment, the appearance of the materials was verified by X-ray diffraction peaks. The reorganization of the amorphous solid was confirmed by Raman and IR spectroscopy along with XPS and SEM, with a more homogeneous phase formation being observed.

Preparation and characterization of BaBi2Nb2O9(BBN) ceramics synthetized by polymeric precursors method

Pure BBN powders and with addition of 1 and 2 wt% in excess of bismuth were obtained by Pechini Method. The powders calcined at 300°C/4h were analyzed by TG/DTA to study the temperature of organic matter decomposition. A systematic study of calcination temperature and time to the formation of the BBN phase was performed and the phase formation was accompanied by XRD. The calcined powders at 800°C during 2h were analyzed by infrared spectroscopy and by BET. The powders were isostaticaly pressed and sintered at temperatures ranging from 900°C to 1000°C. The ceramics were characterized by XRD to control the crystalline phase and by SEM to analyze the microstructure.

Preparation and characterization of spherical yttrium iron garnet via coprecipitation

The purpose of this work is to obtain spherical particles yttrium iron garnet (YIG) by coprecipitation technique. The spherical particles were obtained from either nitrate or chloride salt solutions by controlling the precipitation medium. Different agents of dispersion such as PVP and ammonium iron sulfate were used to optimize the shape and size of YIG. Samples were characterized by X-ray diffraction, scanning electron microscopy and vibrating sample magnetometry. The results show that the samples phase transition takes place at 850°C (orthorhombic phase) and at 1200°C (cubic phase). Spherical shape particles, with diameter of around 0.5 μm, present magnetization values close to the bulk value (26 emu g -1). © 2001 Elsevier Science B.V. All rights reserved.

Purification and characterization of two β-glucosidases from the thermophilic fungus Thermoascus aurantiacus

β-Glucosidase from the fungus Thermoascus aurantiacus grown on semi-solid fermentation medium (using ground corncob as substrate) was partially purified in 5 steps-ultrafiltration, ethanol precipitation, gel filtration and 2 anion exchange chromatography runs, and characterized. After the first anion exchange chromatography, β-glucosidase activity was eluted in 3 peaks (Gl-1, Gl-2, Gl-3). Only the Gl-2 and Gl-3 fractions were adsorbed on the gel matrix. Gl-2 and Gl-3 exhibited optimum pH at 4.5 and 4.0, respectively. The temperature optimum of both glucosidases was at 75-80°C. The pH stability of Gl-2 (4.0-9.0) was higher than Gl-3 (5.5-8.5); both enzyme activities showed similar patterns of thermostability. Under conditions of denaturing gel chromatography the molar mass of Gl-2 and Gl-3 was 175 and 157 kDa, respectively. Using 4-nitrophenyl β-D-glucopyranoside as substrate, Km values of 1.17 ± 0.35 and 1.38 ± 0.86 mmol/L were determined for Gl-2 and Gl-3, respectively. Both enzymes were inhibited by Ag+ and stimulated by Ca2+.

Isolation and characterization of microsatellite loci from the forage species Arachis pintoi (Genus Arachis)

Arachis pintoi is an alternative to forage production in the tropics. Its germplasm comprises more than 150 accessions, that could be used to improve it. Our objective was the isolation and characterization of microsatellite loci in A. pintoi to be used to molecular evaluation of this germplasm and of A. repens (section Caulorrhizae). Seven loci were analyzed using five accessions of A. repens and 20 accessions of A. pintoi. The high variation found makes clear the high potential of this marker in genetic studies in these species. The developed markers showed total transferability to A. repens.

Purification and characterization of xylanases from Aspergillus giganteus

A strain of Aspergillus giganteus cultivated in a medium with xylan produced two xylanases (xylanase I and II) which were purified to homogeneity. Their molar mass, estimated by SDS-PAGE, were 21 and 24 kDa, respectively. Both enzymes are glycoproteins with 50°C temperature optimum; optimum pH was 6.0-6.5 for xylanase I and 6.0 for xylanase II. At 50°C xylanase I exhibited higher thermostability than xylanase II. Hg2+, Cu 2+ and SDS were strong inhibitors, 1,4-dithiothreitol stimulated the reaction of both enzymes. Both xylanases are xylan-specific; kinetic parameters indicated higher efficiency in the hydrolysis of oat spelts xylan. In hydrolysis of this substrate, xylotriose, xylotetraose and larger xylooligosaccharides were released and hence the enzymes were classified as endoxylanases.

Screening for pectinolytic activity of wood-rotting basidiomycetes and characterization of the enzymes

Seventy-five fungal strains from different groups of basidiomycetes, newly isolated from rotten wood, were screened for pectinolytic activity. Despite the fact that basidiomycetes are scarcely referred to as pectinase producers, the polygalacturonase (PG) activity was detected in 76 % of the strains; 16 % with activity higher than 40 nkat/g, 40 % between 13.3 and 40 nkat/g, and 44 % with activity lower than 13.3 nkat/g. The highest productions were obtained among the fungi from order Aphyllophorales, family Polyporaceae. The characterization of the enzymes from the highest PG producers (Lentinus sp., Gloeophyllum striatum, Pycnoporus sanguineus, Schizophyllum commune) showed optimum temperature for catalytic activity at 60-70°C and two peaks of pH optimum (3.5-4.5 and 8.5-9.5). The enzymes exhibited high pH stability (3.0-11.0) but after incubation at 40°C for 1 h their activity dropped by 18-73 %.

Cloning and characterization of the cDNA for the Brazilian Cratomorphus distinctus larval firefly luciferase: Similarities with European Lampyris noctiluca and Asiatic Pyrocoelia luciferases

Studies on firefly (Lampyridae) luciferases have focused on nearctic species of Photinus and Photuris and Euroasiatic species of Lampyris, Luciola, Hotaria, and Pyrocoelia. Despite accounting for the greatest diversity of fireflies in the world, no molecular studies have been carried out on the highly diverse genera from the neotropical region. Here we report the luciferase cDNA cloning for the larva of the Brazilian firefly Cratomorphus distinctus. The cDNA has 1978 bp and codes for a 547-residue-long polypeptide. Noteworthy, sequence comparison as well as functional properties show the highest degree of similarity with Lampyris noctiluca (93%) and Pyrocoelia spp. (91%) luciferases, suggesting a close phylogenetic relationship despite the geographical distance separating these species. The bioluminescence emission spectrum peaks at 550 nm and, as expected, is sensitive to pH, shifting to 605 nm at pH 6. The kinetic properties of the recombinant luciferase were similar to those of other firefly luciferases. © 2004 Elsevier Inc. All rights reserved.

Synthesis and characterization of poly-o-toluidine: Kinetic and structural aspects

Poly(o-methylaniline) (poly-o-toluidine, PTOL) was synthesized by chemical oxidation of o-toluidine with ammonium peroxydisulfate in an aqueous 1.0 mol L -1 HCl solution. The progress of polymerization was followed by measuring the open-circuit potential (OCP) of a Pt electrode immersed in the reaction medium with the polymerization time. The chemical synthesis of PTOL was carried out at different monomer:oxidant (M:O) molar ratios (4:1, 2:1, 1.5:1, 1:1, and 0.66:1), and the products obtained were characterized by infrared spectroscopy, gel permeation chromatography, and X-ray diffraction. The molecular weight and percentage of crystallinity of PTOL are higher for samples synthesized in an excess of the monomer, i.e. at higher M:O ratios. However, the yield of PTOL prepared at higher M:O ratios is considerably low, in particular at a 4:1 M:O ratio, which is the M:O ratio most commonly used in the literature to synthesize polyaniline and its derivatives.

Synthesis and characterization of 0.9PMN-0.1PT powders by the use of a modified columbite precursor

The complex perovskite compound 0.9PbMg 1/3Nb 2/3O 3-0.1PbTiO 3 is one of the most promising relaxor ceramic because the addition of lead titanate increases T m, by about 5°C/mol% from intrinsic T m value for pure PMN (near -7 to -15°C). A Ti-modified columbite precursor was used to prepare PMN-PT powders containing single perovskite phase. This variation on columbite route includes Ti insertion in MgNb 2O 6 orthorhombic structure so that individual PT synthesis becomes unnecessary. Furthermore, effects of Li additive on columbite and PMN-PT structures were studied by XRD to verify the phase formation at each processing step. XRD data were also used for the structural refinement by Rietveld method. The additive acts increasing columbite powders crystallinity, and the amount of perovskite phase was insignificantly decreased by lithium addition. By SEM micrographs it was observed that Li presence in PMN-PT powders leads to the formation of rounded primary particles and for lmol% of additive, the grain size is not changed, different from when this concentration is enhanced to 2mol%.

Ethylcelullose microspheres containing sodium diclofenac: Development and characterization

The objective of the present study was the development and characterization of ethylcellulose microspheres containing diclofenac and the determination of the in vitro drug release profile. Microspheres were prepared by emulsification/solvent evaporation method using ethyl acetate as solvent for the polymer and water as non solvent. The microspheres were characterized by morphologic and granulometric analyses. The amount of encapsulated drug as well as its release profile in vitro were also determined. The product obtained was microparticles with smooth surface and narrow size distribution, about 50% of the particles being smaller than 5 μm. The methodology used allowed drug encapsulation with a good yield and the system provided a controlled release of diclofenac.

Structural control of photoluminescence of four poly(urethane-urea-co-1,3,5-triazine)s: Synthesis and characterization

A series of segmented poly(urethane-urea)s containing 1,3,5 triazine in the hard block and hexamethylene spacers in the soft block was prepared. The hard to soft segment ratio was varied systematically, to afford a series of polymers in which the chromophore concentration varied from 4.2% to 18.1%. Although triazine emission is located in the UV region, the films with higher content of the chromophore emitted a visible blue light (425 nm) when excited at the very red-edge of the absorption band. The photophysical properties of the materials were strongly dependent on the relative amount of triazine moieties along the main chain. Isolated moieties emit in copolymers with small amount of triazine groups, indicating that even though in solid state, these moieties tend to be apart. Two photophysical consequences were observed when the amount of triazine increases: there is some energy transfer process involving isolated moieties with consequent decrease of the lifetime and an additional red-edge emission attributed to aggregated lumophores. The mono-exponential decay observed for the isolated form is substituted by a bi-exponential decay of the aggregated species. The materials were not strong emitters, but since the N-containing triazine moieties are good electron transport groups, the polymers have potential application as electron transport enhancers in various applications. © 2006 Elsevier B.V. All rights reserved.