PARÂMETROS TERMODINÂMICOS DA CASCA DE LARANJA DESIDRATADA

The global energy scenario is currently a widely discussed topic, with growing concern about the future supplies. Thus, much attention has been dedicated to the utilization of biomass as an energy resource. In this respect, orange peel has become a material of great interest, especially to Brazil, which generates around 9.5 million tons of this waste per year. To this end, the authors studied the kinetics of the thermal processing of dried orange peel in inert and oxidizing atmosphere. The thermodynamic parameters were determined by the Ozawa-Flynn-Wall method for the global process observed during heating from the 25°C up to 800°C. The thermal analysis in air and nitrogen showed 3-2 stages of mass loss, respectively, with approximately 20% residual mass under a nitrogen atmosphere. The increase in the values of activation energy for the conversion points between 20% and 60% for thermal effects in air and nitrogen atmosphere was observed. The activation energy obtained in an oxidizing atmosphere was higher than that obtained under a nitrogen atmosphere. The fourier-transform infrared spectroscopy and X-ray diffraction analysis showed that the material has a high level of complexity with the presence of alkali and alkaline earth groups as well as phosphate, plus substances such as pectin, cellulose and lignin.

PYROLIGNEOUS LIQUOR PRODUCED FROM ACACIA MEARNSII DE WILD WOOD UNDER CONTROLLED CONDITIONS AS A RENEWABLE SOURCE OF CHEMICALS

Acacia mearnsii de Wild (black wattle) is one of the most important trees planted in Southern Brazil for tannin extraction and charcoal production. The pyrolysis of the black wattle wood used for obtaining charcoal is performed in brick ovens, with the gas fraction being sent directly into the environment. The present study examines the condensable compounds present in the liquor produced from black wattle wood at different thermal degradation conditions, using gas chromatography coupled with mass spectrometry (GC/MS). Branches of black wattle were thermally degraded at controlled ambient and temperature conditions. Overall, a higher variety of compounds were obtained under atmospheric air pressure than under synthetic air pressure. Most of the tentatively identified compounds, such as carboxylic acids, phenols, aldehydes, and low molecular mass lignin fragments, such as guayacol, syringol, and eugenol, were products of lignin thermoconversion. Substituted aromatic compounds, such as vanillin, ethyl vanillin, and 2-methoxy-4-propeny-phenol, were also identified. At temperatures above 200 ºC, furan, 2-acetylfuran, methyl-2-furoate, and furfural, amongst others, were identified as polysaccharide derivatives from cellulose and hemicellulose depolymerization. This study evidences the need for adequate management of the condensable by-products of charcoal production, both for economic reasons and for controlling their potential environmental impact.

NANOCRISTAIS DE CELULOSE A PARTIR DE CELULOSE BACTERIANA

Bacterial cellulose produced from Gluconacetobacter xilinus was used to produce cellulose nanocrystals by sulfuric acid hydrolysis. Hydrolysis was performed with 64% sulfuric acid at 50 ºC with the hydrolysis time ranging between 5 and 90 min. The production of nanocrystals was observed to have size distributions that were dependent on hydrolysis times up to 10 min, after which time the suspensions showed distributions closer in size. Results from thermal analysis and X-ray diffraction showed that the amorphous cellulose was removed, leaving only the crystalline portion. Self-supported films were formed from the suspension of nanocrystals and had iridescence characteristics. The films were characterized by microscopy measures and specular reflectance.

Hemiselluloosien erotus ja in situ -modifiointi

Hemiselluloosat kuuluvat selluloosan ja ligniinin ohella puun ja muiden kasvimateriaalien päärakenneaineksiin. Hemiselluloosan kemiallisessa koostumuksessa on eroja kasvilajien välillä, mikä tekee ryhmästä hyvin monimuotoisen. Lehtipuiden pääasiallinen hemiselluloosa on glukuroniksylaani. Ksylaaneja esiintyy laajasti myös muissa kasveissa erilaisina rakenteina. Havupuiden yleisin hemiselluloosa on puolestaan galaktoglukomannaani. Arabinogalaktaani on erityisesti lehtikuusesta runsaana löytyvä hemiselluloosa, jota muissa puulajeissa on vain vähän. Luonnon polymeerejä tutkitaan jatkuvasti muun muassa vaihtoehtojen löytämiseksi raakaöljypohjaisille tuotteille. Aiemmin hemiselluloosia on pääosin hyödynnetty sellaisenaan tai jalostettu esimerkiksi sokereiksi. Selluloosan ja tärkkelyksen tavoin ne voivat kuitenkin toimia myös kemiallisen, fysikaalisen tai entsymaattisen muokkauksen lähtöaineena. Hemiselluloosien käyttöä rajoittaa usein se, että niiden eristäminen kasvimateriaalista hyvällä saannolla on vaikeaa. Useimmiten hemiselluloosa erotetaan biomassasta ligniinin poiston jälkeen uuttamalla erilaisilla reagensseilla, kuten emäksillä. Arabinogalaktaanin erottamiseen ei kuitenkaan vaadita ankaria olosuhteita, vaan yleisimmin siihen riittää uutto vedellä. Kalvosuodatus puolestaan on hyvä keino hemiselluloosan talteenottoon uuttoliuoksista. Tässä työssä tarkasteltiin arabinogalaktaanin erotusta siperianlehtikuusesta uuttokokein. Saadut uuttoliuokset konsentrointiin ja puhdistettiin kalvosuodatusmenetelmillä. Lisäksi tutkittiin eristetyn arabinogalaktaanin käyttöä kemiallisen muokkauksen lähtöaineena, missä pyrkimyksenä oli etenkin in situ -modifiointi suoraan uuttoliuoksessa oleville yhdisteille. Uuttokokeilla saatiin kuitenkin vain pieni osa lehtikuusen arabinogalaktaanista erotetuksi. Myös kalvosuodatusvaiheen aikana menetettiin osa uuttoliuosten arabinogalaktaanista. Koska arabinogalaktaanipitoisuus uuttoliuoksissa jäi hyvin alhaiseksi, in situ -modifiointeja oli vaikea saada onnistumaan. Uutto-olosuhteiden lisätutkimuksella sekä kiinnittämällä erityistä huomiota suodatuskalvojen valintaan voitaneen pitoisuutta nostaa ja saada lisämateriaalia kemiallista muokkausta varten.

Dewatering of hard-to-dewater pulps

Nanocellulose has much potential for enhancing the tensile strength of paper but it slows down significantly drainage, restricting its use in industrial scale. Main objective of the work was to find ways to improve the dewatering of nanocellulose-containing papers. The effects of cationic potato starch, microparticle system and filler addition on dewatering and such key properties as formation, tensile strength and air permeance of manufactured paper were studied. Test points had 0, 4 or 8 % CNF and 0, 15 or 30 % PCC content. Based on earlier studies, 25 mg/g starch dosage was added to some test points. Modern microparticle system, consisted of cationic polyacrylamide and amorphous silica, was used in few test points. Dosages for both components were 0.3 and 0.6 mg/g, following the recommendations of the supplier. Also, the influences of CNF and filler on drying behaviour after different stages (drainage, wet pressing and cylinder drying) were estimated. Following trends were observed. Starch does not have unambiguous influence on dewatering. In some cases, it improved drainage slightly but effects on the properties of end product were discovered small. Filler quickened dewatering but large proportions were noticed to be detrimental for the drainage, air permeance and tensile strength. Microparticle system improved drainage notably, especially if CNF dosage was high. In addition, microparticle system increased tensile strength and decreased air permeance. However, its effects on formation were detrimental. Dewatering of nanocellulose-containing furnishes is treatable up to a certain point. In the end, such drainage times that were measured from test points which consisted only of pure kraft pulps are awkward to reach.

Potentiometric determination of captopril in pharmaceutical formulations

A simple, precise, rapid and low-cost potentiometric method for captopril determination in pure form and in pharmaceutical preparations is proposed. Captopril present in tablets containing known quantity of drug was potentiometrically titrated in aqueous solution with NaOH using a glass pH electrode, coupled to an autotitrator. No interferences were observed in the presence of common components of the tablets as lactose, microcrystalline cellulose, croscarmellose sodium, starch and magnesium stearate. The analytical results obtained by applying the proposed method compared very favorably with those obtained by the United States Pharmacopoeia Standard procedure. Recovery of captopril from various tablet dosage formulations range from 98.0 to 102.0%.

Lability of Cd, Cr, Cu, Mn and Pb complexed by aquatic humic substances

The lability of Cd(II), Cr(III), Cu(II), Mn(II) and Pb(II) complexed by humic substances (HSs) was investigated by means of ion exchange on cellulose modified with p-aminobenzoic groups (Cell-PAB), using a batch procedure. The HSs were extracted from water samples using adsorption in a column packed with XAD 8 resin. The metal-HS complexes were prepared by adding solutions containing all the aforementioned metal ions ( Cd(II), Cr(III), Cu(II), Mn(II) and Pb(II) ). The results indicated that the distribution coefficients (Kd) of Cell-PAB decreased with the presence of HSs, and that the lability of metal fractions complexed by HSs decreases in pH values > 4.0, complexation time > 10 h and HS concentration > 500 mg L-1. The metal exchange between HSs and Cell-PAB exhibited the following order of metal ion lability: Cd < Pb < Mn @ Cr < Cu.

Natural and synthetic fibres improving tensile strength and elongation of paper products

The theory part of the Master’s thesis introduces fibres with high tensile strength and elongation used in the production of paper or board. Strong speciality papers are made of bleached softwood long fibre pulp. The aim of the thesis is to find new fibres suitable for paper making to increase either tensile strength, elongation or both properties. The study introduces how fibres bond and what kind of fibres give the strongest bonds into fibre matrix. The fibres that are used the in manufacturing of non-wovens are long and elastic. They are longer than softwood cellulose fibres. The end applications of non-wovens and speciality papers are often the same, for instance, wet napkins or filter media. The study finds out which fibres are used in non-wovens and whether the same fibres could be added to cellulose pulp as armature fibres, what it would require for these fibres to be blended in cellulose, how they would bind with cellulose and whether some binding agents or thermal bonding, such as hot calendaring would be necessary. The following fibres are presented: viscose, polyester, nylon, polyethylene, polypropylene and bicomponent fibres. In the empiric part of the study the most suitable new fibres are selected for making hand sheets in laboratory. Test fibres are blended with long fibre cellulose. The test fibres are viscose (Tencel), polypropylene and polyethylene. Based on the technical values measured in the sheets, the study proposes how to continue trials on paper machine with viscose, polyester, bicomponent and polypropylene fibres.

Formation of polyelectrolyte multilayers and polyelectrolyte complexes in dual polymer treatment of papermaking pulp

The goal of this study was to find a new approach to modify chemically the properties of paper by improving fiber quality. This Master’s thesis includes the multiple polymer treatment in general and themeasurement methods with which the formation of multilayers and complexes can be noticed. The treatment by an oppositely charged dual polymer system is a good approach to increase paper strength. In this work, starch, a cationic polymer, and carboxymethyl cellulose (CMC), an anionic polymer, were used step-by-step to improve paper strength. The adsorption of cationic starch and CMC on cellulose fibers were analyzed via polyelectrolyte titration. The results showed that paper strength was enhanced slightly with a layer-by-layer assembly of the polymers. However, if the washing stage, which was required for layer-by-layer assembly, was eliminated, the starch/CMC complex was deposited on fibers more efficiently, and the paper strength was improved more significantly.

Biokaasu-, bioetanoli- ja yhdistelmäprosessin energia- ja hiilidioksiditase vertailu

Biojäte soveltuu erinomaisesti biokaasuprosessin raaka-aineeksi sisältämänsä runsaan or-gaanisen aineksen vuoksi. Bioetanoliprosessin raaka-aineeksi se soveltuu, koska biojäte sisäl-tää runsaasti tärkkelystä sekä selluloosaa. Tässä työssä tutkittiin laskennallisesti bioetanoli-, biokaasu- sekä näiden yhdistelmäprosessin energia- ja hiilidioksiditaseita kirjallisuuden tietoihin pohjautuen. Biokaasuprosessista lopputuotteena saatavan biometaanin käyttäminen bensiiniä korvaavana liikennepolttoaineena tuottaa jo pelkästään palamistuotteena syntyvän hiilidioksidin säästöinä 62 kg/tbiojätettä. Energian suhteen biokaasuprosessi on selvästi yliomavaraisin kaikista kolmesta prosessista, vaikka energiankulutukseen huomioidaan myös jalostuksen tarvitsema sähkönku-lutus. Biokaasuprosessissa oma käyttö on alle 20 % lopputuotteen lämpöarvosta, yhdistelmä-prosessin osalta luku on 4 %-yks alhaisempi.

Kiintoaineen ja nesteen erotusprosessit lignoselluloosaetanolin tuotannossa

Työn tarkoituksena on tehdä kirjallisuuskatsaus kiintoaine-neste-erotusprosesseihin lignoselluloosaetanolin tuotannossa. Työssä keskitytään hydrolysoidun ligniinipitoisen lignoselluloosamateriaalin kiintoaine-neste-erotukseen. Tarkoituksena on tutkia lignoselluloosamateriaalin suodatus- ja sentrifugointiprosesseja sekä niiden vaikutusta lignoselluloosaetanolin tuotantoon.

Mapping of QTLs related with wood quality and developmental characteristics in hybrids (Eucalyptus grandis x Eucalyptus urophylla)

The present work aimed to characterize and identify QTLs for wood quality and growth traits in E. grandis x E. urophylla hybrids. For this purpose a RAPD linkage map was developed for the hybrids (LOD=3 and r=0.40) containing 52 markers and 12 linkage groups. Traits related to wood quality and growth were evaluated in the QTL analyses. QTL analyses were performed using chi-square tests, single-marker, interval mapping and composite interval mapping analyses. All approaches led to the identification of similar QTLs associated with wood density, cellulose pulp yield and percentage of extractives, which were detected and confirmed by both the interval mapping and composite interval mapping methodologies. Some QTLs regions were confirmed only by the composite interval mapping methodology: percentage of soluble lignin, percentage of insoluble lignin, CBH and total height. Overlapping QTLs regions were detected, and these, can be the result of major genes involved in the regulation and control of the growth traits by epistatic interactions. In order to evaluate the effect of early selection using RAPD molecular data, molecular markers adjacent to QTLs were used genotype selection. The analysis of selection differential values suggests that for all the traits the phenotypic selection at seven years should generate larger genetic gains than early selection assisted by molecular markers and the combination of the strategies should elevate the selection efficiency.

Reproductive ecology of the exotic tree Muntingia calabura L. (Muntingiaceae) in southeastern Brazil

The exotic tree Muntingia calabura L. (Muntingiaceae), a species native to Central America, is used as fish feed and fiber and cellulose production in Brazil. This study was carried out in urban areas and verified the reproductive biology of this plant species. Flower and fruit morphology, compatibility system, reproductive phenology, pollination and frugivore animals, and germination of disseminated seeds were recorded by standard field and laboratory procedures. This tree is self-compatible and autonomously self-pollinated, with its flowers being mainly visited by bees and its fruits consumed by birds and bats. Germination of its dispersed seeds is fast and occurs at a high rate. The results of this work suggest that M. calabura is very adaptable to cultivated areas,thus being an excellent choice for urban reforestation. However, its reproductive characteristics place this plant as an invasive species with significant potential in southeastern Brazil.

Kalvosuodatuksen ja adsorption yhdistäminen biojalostamon erotusprosesseissa

Tässä diplomityössä tutkittiin kalvosuodatuksen ja adsorption yhdistämistä biojalostamon erotusprosesseissa. Työn kirjallisuusosassa käsitellään hemiselluloosien erottamista puusta, kalvosuodatusta hemiselluloosien käsittelyssä sekä hemiselluloosien pilkkomista sokereiksi ja sokereiden kromatografista erotusta. Kokeellisessa osassa tutkittiin hemiselluloosahydrolysaatin fraktioimista kalvosuodatuksella ja adsorbenttikäsittelyn vaikutusta hydrolysaatin suodatettavuuteen. Kokeellisessa osassa tutkittiin myös fraktioinnin vaikutusta hartsien likaantumiseen happohydrolyysin jälkeisessä kromatografisessa erotuksessa. Työssä kokeiltiin useita erilaisia kalvoja, mutta suurin osa suodatuksista tehtiin regeneroidusta selluloosasta valmistetulla kalvolla UC030 ja polyeetterisulfoni kalvolla UFX5. Esikäsittelyyn käytettiin XAD16 adsorbenttia ja hartsien likaantumista tutkittiin CS12GC Na+ hartsilla. Suodatuskokeet tehtiin sekä laboratoriomittakaavan Amicon-suodattimella että pilot-mittakaavan CR- suodattimella. Työn tulokset osoittivat, että konsentroituneen hemiselluloosafraktion tuottaminen tehokkaasti ei onnistu kalvosuodatuksella ilman esikäsittelyä. Kalvon likaantumisen vuoksi permeaattivuo laski hyvin nopeasti niin alhaiseksi, ettei suodatuksen jatkaminen olisi taloudellisesti kannattavaa. Hydrolysaatin esikäsittely XAD16 adsorbentillä poisti tehokkaasti kalvoja likaavia uuteaineita ja ligniiniä. Adsorbenttikäsittelyn jälkeen hydrolysaatin suodattaminen onnistui ilman permeaattivuon huomattavaa alenemista toisessa suodatusvaiheessa ja saatiin aikaiseksi hyvin konsentroitunut hemiselluloosafraktio.

Identification of extractives and polysaccharides as foulants in membrane filtration of pulp and paper mill effluents

The search for new renewable materials has intensified in recent years. Pulp and paper mill process streams contain a number of potential compounds which could be used in biofuel production and as raw materials in the chemical, food and pharmaceutical industries. Prior to utilization, these compounds require separation from other compounds present in the process stream. One feasible separation technique is membrane filtration but to some extent, fouling still limits its implementation in pulp and paper mill applications. To mitigate fouling and its effects, foulants and their fouling mechanisms need to be well understood. This thesis evaluates fouling in filtration of pulp and paper mill process streams by means of polysaccharide model substance filtrations and by development of a procedure to analyze and identify potential foulants, i.e. wood extractives and carbohydrates, from fouled membranes. The model solution filtration results demonstrate that each polysaccharide has its own fouling mechanism, which also depends on the membrane characteristics. Polysaccharides may foul the membranes by adsorption and/or by gel/cake layer formation on the membrane surface. Moreover, the polysaccharides interact, which makes fouling evaluation of certain compound groups very challenging. Novel methods to identify wood extractive and polysaccharide foulants are developed in this thesis. The results show that it is possible to extract and identify wood extractives from membranes fouled in filtration of pulp and paper millstreams. The most effective solvent was found to be acetone:water (9:1 v/v) because it extracted both lipophilic extractives and lignans at high amounts from the fouled membranes and it was also non-destructive for the membrane materials. One hour of extraction was enough to extract wood extractives at high amounts for membrane samples with an area of 0.008 m2. If only qualitative knowledge of wood extractives is needed a simplified extraction procedure can be used. Adsorption was the main fouling mechanism in extractives-induced fouling and dissolved fatty and resin acids were mostly the reason for the fouling; colloidal fouling was negligible. Both process water and membrane characteristics affected extractives-induced fouling. In general, the more hydrophilic regenerated cellulose (RC) membrane fouled less that the more hydrophobic polyethersulfone (PES) and polyamide (PA) membranes independent of the process water used. Monosaccharide and uronic acid units could also be identified from the fouled synthetic polymeric membranes. It was impossible to analyze all monosaccharide units from the RC membrane because the analysis result obtained contained degraded membrane material. One of the fouling mechanisms of carbohydrates was adsorption. Carbohydrates were not potential adsorptive foulants to the sameextent as wood extractives because their amount in the fouled membranes was found to be significantly lower than the amount of wood extractives.