Thermal Treatments of Fe—Mn Alkoxide of Glycerol: Infrared absorption and emission

Synthetic Fe—Mn alkoxide of glycerol samples are submitted to controlled heating conditions and examined by IR absorption spectroscopy. On the other hand, the same sample is studied by infrared emission spectroscopy (IRES), upon heating in situ from 100 to 600°C. The spectral techniques employed in this contribution, especially IRES, show that as a result of the thermal treatments ferromagnetic oxides (manganese ferrite) are formed between 350 and 400°C. Some further spectral changes are seen at higher temperatures.

The effect of alternate supply of shielding gases in austenite stainless steel GTA welding

Welding system has now been concentrated on the development of new process to achieve cost savings, higher productivity and better quality in manufacturing industry. Discrete alternate supply of shielding gas is a new technology that alternately supplies the different kinds of shielding gases in weld zone. As the newdevelopedmethods compared to the previous generalwelding with a mixing supply of shielding gas, it cannot only increase thewelding quality, but also reduce the energy by 20% and the emission rate of fume. As a result, under thesamewelding conditions,comparedwith thewelding by supplying pure argon, argon + 67% helium mixture by conventional method and thewelding by supplying alternately pure argon and pure helium by alternate method showed the increased welding speed. Also, the alternate method showed the same welding speed with argon + 67% helium mixture without largely deteriorating of weld penetration. The alternate method with argon and helium compared with the conventional methods of pure argon and argon + 67% helium mixture produced the lowest degree of welding distortion.

Aging and the force-velocity relationship of muscles

Aging in humans is associated with a loss in neuromuscular function and performance. This is related, in part, to the reduction in muscular strength and power caused by a loss of skeletal muscle mass (sarcopenia) and changes in muscle architecture. Due to these changes, the force-velocity (f-v) relationship of human muscles alters with age. This change has functional implications such as slower walking speeds. Different methods to reverse these changes have been investigated, including traditional resistance training, power training and eccentric (or eccentrically-biased) resistance training. This review will summarise the changes of the f-v relationship with age, the functional implications of these changes and the various methods to reverse or at least partly ameliorate these changes.

The mandatory notification of data breaches : issues arising for Australian and EU legal developments

Public and private sector organisations are now able to capture and utilise data on a vast scale, thus heightening the importance of adequate measures for protecting unauthorised disclosure of personal information. In this respect, data breach notification has emerged as an issue of increasing importance throughout the world. It has been the subject of law reform in the United States and in other jurisdictions. This article reviews US, Australian and EU legal developments regarding the mandatory notification of data breaches. The authors highlight areas of concern based on the extant US experience that require further consideration in Australia and in the EU.

Parents as coteachers of science and technology in a middle-school classroom

This study explores coteaching/cogenerative dialoguing with parents to investigate how it may be employed to engage parents more meaningfully in schools. The cogens provided a space where participants became aware of resources available for coteaching, made decisions about planning and enacting coteaching, as well as interstitial culture that facilitated positive parent-teacher relationships.

Photo-crosslinking of functionalised lactide oligomers for the fabrication of osteochondral tissue engineering scaffolds

In the fabrication of osteochondral tissue engineering scaffolds, the two distinct tissues impose different requirements on the architecture. Stereo-lithography is a rapid prototyping method that can be utilised to make 3D constructs with high spatial control by radical photopolymerization. In this study, biodegradable resins are developed that can be applied in stereo-lithography. Photo-crosslinked poly(lactide) networks with varying physical properties were synthesised, and by photo polymerizing in the presence of leachable particles porous scaffolds could be prepared as well.

Properties of porous structures prepared by stereolithography using a polylactide resin

Rapid prototyping techniques such as stereolithography allow for building designed tissue engineering scaffolds with high accuracy. In this work, a stereolithography resin based on poly(D,L-lactide) was developed. Biodegradable scaffolds with varying porosity were built from this resin. The scaffolds were analysed by μCT-scanning and compression testing. The porous structures showed excellent mechanical properties in the range of trabecular bone.

Predicting mothers’ decisions to introduce complementary feeding at 6 months : an investigation using an extended theory of planned behaviour

In Australia and other developed countries there is poor adherence to guidelines recommending the introduction of complementary feeding to infants at 6 months of age. We aimed to investigate, via adopting a theory of planned behaviour framework and incorporating additional normative and demographic influences, mothers’ complementary feeding intentions and behaviour. Participants were 375 primiparas who completed an initial questionnaire (infant age 13±3weeks) that assessed the theory of planned behaviour constructs of attitude, subjective norm, and perceived behavioural control, as well as group norm and additional maternal and infant variables of mothers’ age, education level, weight status perception, current maternal feeding practices, and infant birth weight. Approximately, 3 months after completion of the main questionnaire, mothers completed a follow-up questionnaire that assessed the age in months at which the infant was first introduced to solids. The theory of planned behaviour variables of attitude and subjective norm, along with group norm, predicted intentions, with intention, mothers’ age (older more likely), and weight status perception (overweight less likely) predicting behaviour. Overall, the results highlight the importance of attitudes, normative influences, and individual characteristics in complementary feeding decision-making which should be considered when designing interventions aimed at improving adherence to current maternal feeding guidelines.

Control and protection of a microgrid connected to utility through back-to-back converters

This paper discusses the control and protection of a microgrid that is connected to utility through back-to-back converters. The back-to-back converter connection facilitates bidirectional power flow between the utility and the microgrid. These converters can operate in two different modes–one in which a fixed amount of power is drawn from the utility and the other in which the microgrid power shortfall is supplied by the utility. In the case of a fault in the utility or microgrid side, the protection system should act not only to clear the fault but also to block the back-to-back converters such that its dc bus voltage does not fall during fault. Furthermore, a converter internal mechanism prevents it from supplying high current during a fault and this complicates the operation of a protection system. To overcome this, an admittance based relay scheme is proposed, which has an inverse time characteristic based on measured admittance of the line. The proposed protection and control schemes are able to ensure reliable operation of the microgrid.

Removal of toxic arsenic and antimony from groundwater Spiro Tunnel Bulkhead in Park City Utah using colloidal iron hydroxide : comparison with reverse ssmosis

Verification testing of two model technologies in pilot scale to remove arsenic and antimony based on reverse osmosis and chemical coagulation/filtration systems was conducted in Spiro Tunnel Water Filtration Plant located in Park City, Utah, US. The source water was groundwater in abandoned silver mine, naturally contaminated by 60-80 ppb of arsenic and antimony below 10 ppb. This water represents one of the sources of drinking water for Park City and constitutes about 44% of the water supply. The failure to remove antimony efficiently by coagulation/filtration (only 4.4% removal rate) under design conditions is discussed in terms of the chemistry differences between Sb (III, V) and As (III, V). Removal of Sb(V) at pH > 7, using coagulation/filtration technology, requires much higher (50 to 80 times) concentration of iron (III) than As. The stronger adsorption of arsenate over a wider pH range can be explained by the fact that arsenic acid is tri-protic, whereas antimonic acid is monoprotic. This difference in properties of As(V) and Sb(V) makes antimony (V) more difficult to be efficiently removed in low concentrations of iron hydroxide and alkaline pH waters, especially in concentration of Sb < 10 ppb.

Scaling of free convection heat transfer in a triangular cavity for Pr>1

Unsteady natural convection inside a triangular cavity subject to a non-instantaneous heating on the inclined walls in the form of an imposed temperature which increases linearly up to a prescribed steady value over a prescribed time is reported. The development of the flow from start-up to a steady-state has been described based on scaling analyses and direct numerical simulations. The ramp temperature has been chosen in such a way that the boundary layer is reached a quasi-steady mode before the growth of the temperature is completed. In this mode the thermal boundary layer at first grows in thickness, then contracts with increasing time. However, if the imposed wall temperature growth period is sufficiently short, the boundary layer develops differently. It is seen that the shape of many houses are isosceles triangular cross-section. The heat transfer process through the roof of the attic-shaped space should be well understood. Because, in the building energy, one of the most important objectives for design and construction of houses is to provide thermal comfort for occupants. Moreover, in the present energy-conscious society it is also a requirement for houses to be energy efficient, i.e. the energy consumption for heating or air-conditioning houses must be minimized.

A review of natural convection and heat transfer in attic-shaped space

This paper presents a review of studies on natural convection heat transfer in the triangular enclosure namely, in attic-shaped space. Much research activity has been devoted to this topic over the last three decades with a view to providing thermal comfort to the occupants in attic-shaped buildings and to minimising the energy costs associated with heating and air-conditioning. Two basic thermal boundary conditions of attic are considered to represent hot and cold climates or day and night time. This paper also reports on a significant number of studies which have been performed recently on other topics related to the attic space, for example, attics subject to localized heating and attics filled with porous media.

Is there a physicality requirement at Common Law? : a survey of the Pre-NRDC cases discussing ‘Manufacture’

One of the fundamental issues that remains unresolved in patent law today, both in Australia and in other jurisdictions, is whether an invention must produce a physical effect or cause a physical transformation of matter to be patentable, or whether it is sufficient that an invention involves a specific practical application of an idea or principle to achieve a useful result. In short, the question is whether Australian patent law contains a physicality requirement. Despite being recently considered by the Federal Court, this is arguably an issue that has yet to be satisfactorily resolved in Australia. In its 2006 decision in Grant v Commissioner of Patents, the Full Court of the Federal Court of Australia found that the patentable subject matter standard is rooted in the physical, when it held that an invention must involve a physical effect or transformation to be patent eligible. That decision, however, has been the subject of scrutiny in the academic literature. This article seeks to add to the existing literature written in response to the Grant decision by examining in detail the key common law cases decided prior to the High Court’s watershed decision in National Research Development Corporation v Commissioner of Patents, which is the undisputed authoritative statement of principle in regards to the patentable subject matter standard in Australia. This article, in conjunction with others written by the author, questions the Federal Court’s assertion in Grant that the physicality requirement it established is consistent with existing law.

Bilski v Kappos : The United States Supreme Court delivers mixed views on patenting non-physical inventions and business methods

The United States Supreme Court has handed down a once in a generation patent law decision that will have important ramifications for the patentability of non-physical methods, both internationally and in Australia. In Bilski v Kappos, the Supreme Court considered whether an invention must either be tied to a machine or apparatus, or transform an article into a different state or thing to be patentable. It also considered for the first time whether business methods are patentable subject matter. The decision will be of particular interest to practitioners who followed the litigation in Grant v Commissioner of Patents, a Federal Court decision in which a Brisbane-based inventor was denied a patent over a method of protecting an asset from the claims of creditors.