Feasibility of Laminar Plasma-Jet Hardening of Cast Iron Surface

Nontransferred DC laminar plasma jets of stable flow and low impinging pressure acting on the substrate were used to heat W–Mo–Cu cast iron for phase transfer hardening of the surface layer. Substrates were heated in multipass with or without overlapping or heated with only single-pass. Surface morphologies of the molten trace and microstructure of the cross-section were observed, and the hardness distribution of the treated surface layer was examined. The surface layer of single-pass-heated specimen has an average hardness of about 900 HV0.1, while the specimen treated with multipass shows an average hardness of about 700 HV0.1, because of the heat effect from the neighboring pass treating, compared with the substrate hardness of about 300 HV0.1. The results demonstrate the stable and favorably controlled heating of the laminar plasma jet on the substrate surface and feasibility of using it as a tool for surface hardening of cast iron.

Effect of liquid bridge volume on the instability in small-Prandtl-number half zones

A perturbation method is used to examine the linear instability of thermocapillary convection in a liquid bridge of floating half-zone filled with a small Prandtl number fluid. The influence of liquid bridge volume on critical Marangoni number and flow features is analyzed. The neutral modes show that the instability is mainly caused by the bulk flow that is driven by the nonuniform thermocapillary forces acting on the free surface. The hydrodynamic instability is dominant in the case of small Prandtl number fluid and the first instability mode is a stationary bifurcation. The azimuthal wave number for the most dangerous mode depends on the liquid bridge volume, and is not always two as in the case of a cylindrical liquid bridge with aspect ratio near 0.6. Its value may be equal to unity when the liquid bridge is relatively slender.

Surface attachment of protein fibrils via covalent modification strategies.

Chemical control of surface functionality and topography is an essential requirement for many technological purposes. In particular, the covalent attachment of monomeric proteins to surfaces has been the object of intense studies in recent years, for applications as varied as electrochemistry, immuno-sensing, and the production of biocompatible coatings. Little is known, however, about the characteristics and requirements underlying surface attachment of supramolecular protein nanostructures. Amyloid fibrils formed by the self-assembly of peptide and protein molecules represent one important class of such structures. These highly organized beta-sheet-rich assemblies are a hallmark of a range of neurodegenerative disorders, including Alzheimer's disease and type II diabetes, but recent findings suggest that they have much broader significance, potentially representing the global free energy minima of the energy landscapes of proteins and having potential applications in material science. In this paper, we describe strategies for attaching amyloid fibrils formed from different proteins to gold surfaces under different solution conditions. Our methods involve the reaction of sulfur containing small molecules (cystamine and 2-iminothiolane) with the amyloid fibrils, enabling their covalent linkage to gold surfaces. We demonstrate that irreversible attachment using these approaches makes possible quantitative analysis of experiments using biosensor techniques, such as quartz crystal microbalance (QCM) assays that are revolutionizing our understanding of the mechanisms of amyloid growth and the factors that determine its kinetic behavior. Moreover, our results shed light on the nature and relative importance of covalent versus noncovalent forces acting on protein superstructures at metal surfaces.

Insulin analog preparations and their use in children and adolescents with type 1 diabetes mellitus.

Standard or 'traditional' human insulin preparations such as regular soluble insulin and neutral protamine Hagedorn (NPH) insulin have shortcomings in terms of their pharmacokinetic and pharmacodynamic properties that limit their clinical efficacy. Structurally modified insulin molecules or insulin 'analogs' have been developed with the aim of delivering insulin replacement therapy in a more physiological manner. In the last 10 years, five insulin analog preparations have become commercially available for clinical use in patients with type 1 diabetes mellitus: three 'rapid' or fast-acting analogs (insulin lispro, aspart, and glulisine) and two long-acting analogs (insulin glargine and detemir). This review highlights the specific pharmacokinetic properties of these new insulin analog preparations and focuses on their potential clinical advantages and disadvantages when used in children and adolescents with type 1 diabetes mellitus. The fast-acting analogs specifically facilitate more flexible insulin injection timing with regard to meals and activities, whereas the long-acting analogs have a more predictable profile of action and lack a peak effect. To date, clinical trials in children and adolescents have been few in number, but the evidence available from these and from other studies carried out in adults with type 1 diabetes suggest that they offer significant benefits in terms of reduced frequency of nocturnal hypoglycemia, better postprandial blood glucose control, and improved quality of life when compared with traditional insulins. In addition, insulin detemir therapy is unique in that patients may benefit from reduced risk of excessive weight, particularly during adolescence. Evidence for sustained long-term improvements in glycosylated hemoglobin, on the other hand, is modest. Furthermore, alterations to insulin/insulin-like growth factor I receptor binding characteristics have also raised theoretical concerns that insulin analogs may have an increased mitogenic potential and risk of tumor development, although evidence from both in vitro and in vivo animal studies do not support this assertion. Long-term surveillance has been recommended and further carefully designed prospective studies are needed to evaluate the overall benefits and clinical efficacy of insulin analog therapy in children and adolescents with type 1 diabetes.

Governing Equations and Numerical Solutions of Tension Leg Platform with Finite Amplitude Motion

It is demonstrated that when tension leg platform (TLP) moves with finite amplitude in waves, the inertia force, the drag force and the buoyancy acting on the platform are nonlinear functions of the response of TLP. The tensions of the tethers are also nonlinear functions of the displacement of TLP. Then the displacement, the velocity and the acceleration of TLP should be taken into account when loads are calculated. In addition, equations of motions should be set up on the instantaneous position. A theoretical model for analyzing the nonlinear behavior of a TLP with finite displacement is developed, in which multifold nonlinearities are taken into account, i.e., finite displacement, coupling of the six degrees of freedom, instantaneous position, instantaneous wet surface, free surface effects and viscous drag force. Based on the theoretical model, the comprehensive nonlinear differential equations are deduced. Then the nonlinear dynamic analysis of ISSC TLP in regular waves is performed in the time domain. The degenerative linear solution of the proposed nonlinear model is verified with existing published one. Furthermore, numerical results are presented, which illustrate that nonlinearities exert a significant influence on the dynamic responses of the TLP.

Mode I crack growth resistance of metallic foams

A Dugdale-type cohesive zone model is used to predict the mode I crack growth resistance (R-curve) of metallic foams, with the fracture process characterized by an idealized traction-separation law that relates the crack surface traction to crack opening displacement. A quadratic yield function, involving the von Mises effective stress and mean stress, is used to account for the plastic compressibility of metallic foams. Finite element calculations are performed for the crack growth resistance under small scale yielding and small scale bridging in plane strain, with K-field boundary conditions. The following effects upon the fracture process are quantified: material hardening, bridging strength, T-stress (the non-singular stress acting parallel to the crack plane), and the shape of yield surface. To study the failure behaviour and notch sensitivity of metallic foams in the presence of large scale yielding, a study is made for panels embedded with either a centre-crack or an open hole and subjected to tensile stressing. For the centre-cracked panel, a transition crack size is predicted for which the fracture response switches from net section yielding to elastic-brittle fracture. Likewise, for a panel containing a centre-hole, a transition hole diameter exists for which the fracture response switches from net section yielding to a local maximum stress criterion at the edge of the hole.

Alcance y límites de la potencia humana

Resumen: La visión sobre el modo de ser del hombre condiciona, de un modo u otro, su actuar en el mundo. En general, es éste un punto de partida compartido por las distintas corrientes filosóficas al momento de dar respuesta al ejercicio del potencial humano, si bien pueden distanciarse drásticamente al sustentar el pasaje ser-obrar. En este sentido, entre las formas más alejadas entre sí cabe reparar, por una parte, en una concepción que recurre a la justificación de una metafísica realista que reconoce la dialéctica de la participación y, por otra, en una concepción que se declara anti-metafísica al disolver el ser en su negación, en la nada, para exaltar la voluntad de poder del hombre. Si bien este trabajo se desarrollará en el marco de la primera concepción, desde el estudio de la causación del acto de ser en Tomás de Aquino, habré de recurrir a la segunda concepción, en particular al nihilismo nietzscheano, solamente como planteo del estado de la cuestión, buscando remover críticamente una objeción recurrente en la historia del pensamiento sobre el alcance y límites de la operación humana.

Nucleated polymerization with secondary pathways. I. Time evolution of the principal moments.

Self-assembly processes resulting in linear structures are often observed in molecular biology, and include the formation of functional filaments such as actin and tubulin, as well as generally dysfunctional ones such as amyloid aggregates. Although the basic kinetic equations describing these phenomena are well-established, it has proved to be challenging, due to their non-linear nature, to derive solutions to these equations except for special cases. The availability of general analytical solutions provides a route for determining the rates of molecular level processes from the analysis of macroscopic experimental measurements of the growth kinetics, in addition to the phenomenological parameters, such as lag times and maximal growth rates that are already obtainable from standard fitting procedures. We describe here an analytical approach based on fixed-point analysis, which provides self-consistent solutions for the growth of filamentous structures that can, in addition to elongation, undergo internal fracturing and monomer-dependent nucleation as mechanisms for generating new free ends acting as growth sites. Our results generalise the analytical expression for sigmoidal growth kinetics from the Oosawa theory for nucleated polymerisation to the case of fragmenting filaments. We determine the corresponding growth laws in closed form and derive from first principles a number of relationships which have been empirically established for the kinetics of the self-assembly of amyloid fibrils.

Md Simulation Of Dislocation Mobility During Cutting With Diamond Tip On Silicon

By means of Tersoff and Morse potentials, a three-dimensional molecular dynamics simulation is performed to study atomic force microscopy cutting on silicon monocrystal surface. The interatomic forces between the workpiece and the pin tool and the atoms of workpiece themselves are simulated. Two partial edge dislocations are introduced into workpiece Si, it is found that the motion of dislocations does not occur during the atomic force microscopy cutting processing. Simulation results show that the shear stress acting on dislocations is far below the yield strength of Si. (c) 2008 Elsevier Ltd. All rights reserved.

Molecular Dynamics Study Of Mechanical Behaviour Of Screw Dislocation During Cutting With Diamond Tip On Silicon

By means of Tersoff and Morse potentials, a three-dimensional molecular dynamics simulation is performed to study atomic force microscopy cutting on silicon monocrystal surface. The interatomic forces between the workpiece and the pin tool and the atoms of workpiece themselves are calculated. A screw dislocation is introduced into workpiece Si. It is found that motion of dislocations does not occur during the atomic force microscopy cutting processing. Simulation results show that the shear stress acting on dislocation is far below the yield strength of Si.

Films de polietileno oxo-degradados mediante envejecimiento acelerado por radiación UV y calor

Resumen: Los materiales plásticos utilizados en la industria del embalaje y transporte de mercaderías familiares e industriales, presentan numerosas ventajas que los han puesto en su lugar durante los últimos 50 años. En la actualidad, son miles de millones de toneladas anuales de bolsas o embalajes de polietileno, las que diariamente se producen, se usan, se recuperan (en muy pequeña parte) y son finalmente dispuestas, quemadas o literalmente arrojadas al medio ambiente. La alta estabilidad química o la muy baja tasa de degradación, hace que estos residuos perduren en el medio - en la mayoría de los casos por más de 100 años- dependiendo las condiciones ambientales locales. Hace pocos años, se adaptaron conocimientos científicos a esta problemática, y de ello nacieron dos formas de atacar la eliminación del plástico como desecho (más allá del reciclado y uso racional): por un lado, la utilización de bioplásticos con propiedades biodegradables; y por otro, el agregado de aditivos pro-degradantes a plásticos convencionales. El presente trabajo, tiene por objeto tomar a esta última herramienta, sobre la cual se han comenzado a estudiar los mecanismos químicos por los cuales cumplen su función, evaluándolos en distintas condiciones aceleradas de laboratorio. De esta manera, se caracterizaron velocidades de degradación abiótica mediante envejecimientos acelerados con radiación ultravioleta y térmica, para films de polietileno aditivados con un compuesto oxodegradante comercial. Se estudiaron distintas concentraciones de aditivo en el polímero, en función del tiempo de envejecimiento. Las caracterizaciones incluyeron análisis mecánico, análisis térmico diferencial, espectroscopía de absorción infrarroja y de Absorción Atómica.

La Celestina en escenarios argentinos : observaciones comparatistas sobre las adaptaciones de Jorge Goldenberg (1993) y Daniel Suárez Marzal (2007)

Integran este número de la revista ponencias presentadas en Studia Hispanica Medievalia VIII: Actas de las IX Jornadas Internacionales de Literatura Española Medieval, 2008, y de Homenaje al Quinto Centenario de Amadis de Gaula.

Soporte vital y terapia intensiva.Muerte intervenida

El concepto de muerte intervenida comprende todas aquellas situaciones clínicas en las que la abstención o retiro de algún método de soporte vital en el transcurso de la asistencia médica se propone como un límite en el tratamiento, quedando vinculado el mismo con la llegada de la muerte cardiorrespiratoria tradicional. La presencia de una tecnología médica (soporte vital) común en todos los casos, permite la consideración comprensiva de todo su conjunto. Finalmente, en todos ellos la muerte se vincula a una acción u omisión de la tecnología médica. Una evaluación común de estos casos no sólo tiene una lógica derivada de la operatividad que hizo posible la existencia de estos pacientes sino que además promueve la interpretación verdadera y correcta de los hechos por parte de la sociedad. La reflexión sobre la muerte intervenida como un fenómeno emergente de nuestra cultura resulta imprescindible para que la sociedad se involucre y participe en un tema que le incumbe en forma absoluta y exclusiva.

Sistema de legislação informatizada (LEGIN) : uma experiência em gestão da informação jurídica na Câmara dos Deputados

Relato da experiência da Coordenação de Estudos Legislativos da Câmara dos Deputados no processo de organização e recuperação da informação legislativa produzida pelo Poder Legislativo Brasileiro. O Sistema de Legislação Informatizada (LEGIN) foi criado em 2001 com a finalidade de ser a aplicação responsável pelo gerenciamento e recuperação das normas federais e internas da Câmara dos Deputados produzidas desde o período do Império.

Drag on an ellipsoid particle in free-molecular plasma flow

Based on the analysis of molecular gas dynamics, the drag and moment acting on an ellipsoid particle of revolution X-2/a(2) + Y-2/a(2) + Z(2)/c(2) = 1, as an example of nonspherical particles, are studied under the condition of free-molecular plasma flow with thin plasma sheaths. A nonzero moment which causes nonspherical particle self-oscillation and self-rotation around its own axis in the plasma flow-similar to the pitching moment in aerodynamics-is discovered for the first time. When the ratio of axis length c/a is unity, the moment is zero and the drag formula are reduced to the well-known results of spherical particles. The effects of the particle-plasma relative velocity, the plasma temperature, and the particle materials on the drag and moment are also investigated.