Petrologia e geologia estrutural do plutão granítico Barcelona, província Borborema, NE do Brasil

The Dissertation aimed to advance the geological knowledge of the Barcelona Granitic Pluton (BGP). This body is located in the eastern portion of the Rio Grande do Norte Domain (RND), within the São José do Campestre subdomain (SJC), NE of the Borborema Province. The main goal was to understand the geological evolution of the rocks of the pluton and the tectonic setting of magma generation and its emplacement. The BGP has an assumed Ediacaran age and outcropping area of approximately 260 km2, being composed of three varied petrographic/textural facies: (a) porphyritic biotite monzogranite; (b) dykes and sheets of biotite microgranite; (c) dioritic to quartz-dioritic enclaves. The rocks of the BGP have the following structures: (i) a NE-SW and NW-SE directed magmatic fabric (Sγ), accompanied by a magmatic lineation (Lγ) with gentle dip to NE-SW and NW-SE. In the southern portion, there is the concentric pattern of this foliation with medium to high dip, and (ii) a solid state foliation, in part mylonitic (S3+), mainly on the eastern edge with slightly plunging to west. The integration of structural and gravity data permitted to interpret the emplacement of the BGP as controlled by the transcurrent shear zones systems Lajes Pintadas (LPSZ) and Sítio Novo (SNSZ), both of dextral strike-slip kinematics. Mineral chemistry data show that the amphibole form the porphyritic biotite monzogranite facies is hastingsite with moderate Mg / (Mg + Fe) ratios, indicating crystallization under moderate to high ƒO2 and cristallization pressure of around 5.0-6.0 kbar. The biotite tends to be slightly richer in annite molecule and plots in the transitional field from primary biotite to reequilibrated biotite. In discriminant diagrams of magmatic series, the biotite behave like those of subalkaline affinity, consistent with the potassium calc-alkaline / sub-alkaline geochemical affinity of the hosting rock. The opaque minerals are primarily magnetite, with some crystals martitized to hematite indicating relatively oxidizing conditions during magma evolution that originated the BGP. Zoning in plagioclase, K-feldspar and allanite crystals suggest fractional crystallization process. Lithogeochemical data suggest that the facies described for the BGP have similar magma source, usually plotting in the fields and trends of the subalkaline / high potassium calc-alkaline series.

Expressão geofísica-estrutural do lineamento transbrasiliano na porção central da Bacia do Parnaíba (Maranhão-Piauí)

The objective of this study was to characterize the structural-geophysical expression of the Transbrasiliano Lineament (TBL) in the east-central portion of the Parnaíba Basin. The TBL corresponds to a major Neoproterozoic NE-trending shear zone related to the Brasiliano orogenic cycle, with dextral strike-slip kinematics, underlying (but also laterally exposed in the NE and SW basin edges) the sedimentary section of the Parnaíba Basin. In this study, the interpretation of gravity and magnetic anomaly maps is consistent with the TBL kinematics, the signature of the geophysical anomalies corresponding to the high (plastic behaviour) and subsequent declining temperature (ductile to brittle behaviour) stages during Brasiliano and late Brasiliano times. The pattern of residual gravity anomalies is compatible with an S-C dextral pair shaping the geological bodies of an heterogeneous basement, such as slices of gneisses and granulites (positive anomalies), granitic and low-medium grade metasedimentary rocks (negative anomalies). Such anomalies curvilinear trends, ranging from NNE (interpreted as S surfaces) to NE (C surfaces), correspond to flattening surfaces (S), while the NE rectilinear trend must represent a C band. The narrower magnetic anomalies also display NNE to NE (S surfaces) trends and should correspond to similar (although narrower and more discontinuous) sources in the equivalent anomaly patterns. Pre-Silurian pull-apart style grabens may contribute to the NE negative gravimetric anomalies, although this interpretation demands control by seismic data analysis. On the other hand, the curvilinear anomalies associated to contractional trends are incompatible with their interpretation as pre-Silurian graben, in both maps. In the (reduced to the pole) magnetic anomalies map, most of these are again associated to low-temperature shear zones (C planes) and faults, juxtaposing distinct blocks in terms of magnetic properties, or eventually filled with basic bodies. It is also possible that some isolated magnetic anomalies correspond to igneous bodies of late-Brasiliano or Mesozoic age. The basement late discontinuities pattern can be interpreted in analogy to the Riedel fractures model, with steep dipping surfaces and a sub-horizontal movement section. This study also explored 2D gravity modeling controlled by the interpretation of a dip seismic line as regards to the Transbrasiliano Lineament. The rock section equivalent to the Jaibaras Group occupying a graben structure (as identified in the seismic line) corresponds to a discrete negative anomaly superimposed to a gravimetric high, once again indicating a stronger influence of older crystalline basement rocks as gravimetric sources, mainly reflecting the heterogeneities and anisotropies generated at high temperature conditions and their subsequent cooling along the TBL, during the Brasiliano cycle.

Expressão geofísica-estrutural do lineamento transbrasiliano na porção central da Bacia do Parnaíba (Maranhão-Piauí)

The objective of this study was to characterize the structural-geophysical expression of the Transbrasiliano Lineament (TBL) in the east-central portion of the Parnaíba Basin. The TBL corresponds to a major Neoproterozoic NE-trending shear zone related to the Brasiliano orogenic cycle, with dextral strike-slip kinematics, underlying (but also laterally exposed in the NE and SW basin edges) the sedimentary section of the Parnaíba Basin. In this study, the interpretation of gravity and magnetic anomaly maps is consistent with the TBL kinematics, the signature of the geophysical anomalies corresponding to the high (plastic behaviour) and subsequent declining temperature (ductile to brittle behaviour) stages during Brasiliano and late Brasiliano times. The pattern of residual gravity anomalies is compatible with an S-C dextral pair shaping the geological bodies of an heterogeneous basement, such as slices of gneisses and granulites (positive anomalies), granitic and low-medium grade metasedimentary rocks (negative anomalies). Such anomalies curvilinear trends, ranging from NNE (interpreted as S surfaces) to NE (C surfaces), correspond to flattening surfaces (S), while the NE rectilinear trend must represent a C band. The narrower magnetic anomalies also display NNE to NE (S surfaces) trends and should correspond to similar (although narrower and more discontinuous) sources in the equivalent anomaly patterns. Pre-Silurian pull-apart style grabens may contribute to the NE negative gravimetric anomalies, although this interpretation demands control by seismic data analysis. On the other hand, the curvilinear anomalies associated to contractional trends are incompatible with their interpretation as pre-Silurian graben, in both maps. In the (reduced to the pole) magnetic anomalies map, most of these are again associated to low-temperature shear zones (C planes) and faults, juxtaposing distinct blocks in terms of magnetic properties, or eventually filled with basic bodies. It is also possible that some isolated magnetic anomalies correspond to igneous bodies of late-Brasiliano or Mesozoic age. The basement late discontinuities pattern can be interpreted in analogy to the Riedel fractures model, with steep dipping surfaces and a sub-horizontal movement section. This study also explored 2D gravity modeling controlled by the interpretation of a dip seismic line as regards to the Transbrasiliano Lineament. The rock section equivalent to the Jaibaras Group occupying a graben structure (as identified in the seismic line) corresponds to a discrete negative anomaly superimposed to a gravimetric high, once again indicating a stronger influence of older crystalline basement rocks as gravimetric sources, mainly reflecting the heterogeneities and anisotropies generated at high temperature conditions and their subsequent cooling along the TBL, during the Brasiliano cycle.

Influência da utilização do fluido de corte com adição de grafeno na temperatura de usinagem e formação de rebarba no processo de micro fresamento

As time passed, humanity needed the development of new materials used in various activities. High strength materials such as titanium and Inconel for example, had been studied because they are widely used for implants in biomedicine, as well as their use in aerospace and automotive industries. Because of its thermal and mechanical properties, these materials are considered difficult to machine, promoting a rapid wear of cutting tools, primarily caused by the high temperatures in machining. With the development of new materials has emerged the need of developing new manufacturing processes. One of today’s innovative processes is the micro-manufacturing. Being a process with a defined cutting tool geometry, burr formation is a constant and undesirable phenomenon formed during the machininig process. Being detrimental to the manufacturing process, overspending deburring operations are constantly employed leading to increase the aggregate cost to the manufactured material. Assembly components are also impaired if there is no control of the burr, with consequences including the disposal of components due to the occurence of this phenomenon. This paper presents the study of micro-milling Inconel 718, investigating influential parameters in the formation of burrs in order to minimize the occurrence of this phenome non. Different feed rates per tooth and cutting speed are evaluated, and different cutting fluids with different methods of applying the fluid. Adding graphene to cutting fluids was considered as a variable to be investigated, which is considered an excellent solid lubricant, in addition to increasing the thermal conductivity of the cooling solution (AZIMI; MOZAF FARI, 2015). The micro-milling temperature was evaluated in the present work. It was observed a new phenomenon that causes the machined surface temperature decreases below room temperature when using the solution water + oil. This phenomenon is explained in further chapters. In order to unravel this phenomenon, a new test was proposed and, from this test, it can be concluded, comparatively, which cutting fluid has a better cooling property.Using cutting fluid with different thermal properties has shown influence when analy zing burr formation and reducing machining temperature.

Surfactant-mediated variation of band-edge emission in CdS nanocomposites

The optical-structural characteristics of the direct optical band-gap semiconducting series of surfactant template-mediated laminar (CdS)x(CdCl2)y(CnH2n+4N)z nanocomposites are reported. X-ray diffraction measurements of the nanocomposites exhibited interlaminar distances in the range 2.9-3.6 nm with observations of eighth order {0 0 l} diffraction planes indicative of a high degree of laminarity and crystallographic order. Diffuse reflectance measurements have determined that the profile of their emission spectrum is that of a direct band-gap with absorption edges in the range 2.11-2.40 eV, depending on the CdS mole fraction in the nanocomposite. Photoluminescence (PL) excitation and time-resolved PL spectroscopies give an estimate of the maximum relative absorbance of the nanocomposites at ∼420 nm while the minimum was observed at ∼560 nm. The main emission was observed at ∼700 nm with emission from doubly ionized sulphur vacancies observed at ∼615 nm at room temperature. The CdS-containing nanocomposite is thus a surfactant-mediated modular system with variable band-gap energy emission.

The role of material characterisation in the crush modelling of thermoplastic composite structures

The predictive capability of high fidelity finite element modelling, to accurately capture damage and crush behaviour of composite structures, relies on the acquisition of accurate material properties, some of which have necessitated the development of novel approaches. This paper details the measurement of interlaminar and intralaminar fracture toughness, the non-linear shear behaviour of carbon fibre (AS4)/thermoplastic Polyetherketoneketone (PEKK) composite laminates and the utilisation of these properties for the accurate computational modelling of crush. Double-cantilever-beam (DCB), four-point end-notched flexure (4ENF) and Mixed-mode bending (MMB) test configurations were used to determine the initiation and propagation fracture toughness in mode I, mode II and mixed-mode loading, respectively. Compact Tension (CT) and Compact Compression (CC) test samples were employed to determine the intralaminar longitudinal tensile and compressive fracture toughness. V-notched rail shear tests were used to measure the highly non-linear shear behaviour, associated with thermoplastic composites, and fracture toughness. Corresponding numerical models of these tests were developed for verification and yielded good correlation with the experimental response. This also confirmed the accuracy of the measured values which were then employed as input material parameters for modelling the crush behaviour of a corrugated test specimen.

The Transverse Crack Tension test revisited: An experimental and numerical study

Several problems arise when measuring the mode II interlaminar fracture toughness using a Transverse Crack Tension specimen; in particular, the fracture toughness depends on the geometry of the specimen and cannot be considered a material parameter. A preliminary experimental campaign was conducted on TCTs of different sizes but no fracture toughness was measured because the TCTs failed in an unacceptable way, invalidating the tests. A comprehensive numerical and experimental investigation is conducted to identify the main causes of this behaviour and a modification of the geometry of the specimen is proposed. It is believed that the obtained results represent a significant contribution in the understanding of the TCT test as a mode II characterization procedure and, at the same time, provide new guidelines to characterize the mode II crack propagation under tensile loads.

Aproveitamento de subprodutos da indústria de carne suína: caracterização físico-química do queijo de porco

Headcheese is a meat sausage originated from Europe made from hog slaughter by-products. It is a much appreciated product in the South of Brazil which is increasingly established in the market, however it does not have official regulations yet. This study aimed to present the physicochemical characterization of headcheese in a western Santa Catarina industry supervised by Companhia Integrada de Desenvolvimento Agrícola de Santa Catarina and assess 10 different brands to find the relationship between chemical composition and texture profile analysis (TPA). Thus, the chemical composition, energy value, total nitrite, lipid oxidation and physical parameters (color and texture) were evaluated. The product exhibited great variability in moisture content, lipid and protein because the different formulations, processing and intrinsic and extrinsic characteristics of raw material. The utilization of offal provided higher cholesterol and iron levels, and the high content of collagen was accountable for the shear force responses (7.84 ± 1.68 N). The product showed higher amount of sodium, due to the use of additives, but calcium levels were compatible with other sausages. There was a predominance of polyunsaturated fatty acids and polyunsaturated fatty acids/saturated fatty acids ratio was more favorable than other sausage in the same category. Nitrite assured preservation effects and thus lower product levels of oxidation were observed. The high Water Activity and pH 6.5 showed that the product is susceptible to growth of pathogens and requires cooling for preservation. Its brownish occurred due to cooking and production of metmyoglobin. There was a strong positive correlation between collagen and attributes of TPA, especially for chewiness (r = 0.855). The use of Hierarchical Cluster Analysis and Principal Component Analysis were able to separate three groups based on the amount of collagen and texture attributes, especially hardness, gumminess and chewiness.

Avaliação dos parâmetros de insensibilização e os impactos na qualidade da carne de perus (Meleagris gallopavo)

Brazil is the third largest producer and exporter of turkey meat, especially in Paraná state, with the largest production volume. In worldwide the animal welfare is a prerequisite for food quality of animal origin, especially in Europe. The Regulation of European Community No 1099/2009 provides requirements for poultry stunning that associate with animal welfare as a means to minimize the pain and suffering from the slaughter. Improper application of callousness should produce low-quality meat, and significant industry losses. This Research aimed to evaluate the impacts on the quality of meat from turkeys, applying electrical stunning parameters established in the Regulation No 1099/2009 of the Council of 24 September 2009. Was applied an outline with 8 tests set equidistantly to frequency, and set parameters for current and voltage, and a control test. Were conducted qualitative assessments of hematoms and bruises / fractures in carcasses, hematoms, blood splashed and bleeding in turkey breast, and quantitative pH, color (L *), water holding capacity and shear force in turkey breast. The individual assessments showed no significant difference (p>0,05). In multivariate cluster analysis was the formation of two distinct groups: group 1 - 50 Hz to 200 Hz (low frequency) and group 2 - 633 Hz to 1500 Hz (high frequency), which showed significant difference (p= 0,016). In principal component analysis multivariate, the group 1 tend to have a higher incidence of bruising, blood splashed, bleeding and water holding capacity in breast turkeys, and bruises / fractures and hematoms on carcasses. The Group 2 tends to have a lower incidence of these parameters, and higher pH values, shear force and color (L *). Positive correlation was obtained for the parameters pH and shear force (r= 0.7506, p=0.0198); bleeding and splashed blood (r= 0.8811, p= 0.0017), and negative correlation to color (L*) and splashed blood on breast (r= -0.7889; p= 0.0115); breast hematoms and shear force (r= -0.7844; p= 0.0123). It has been observed that at lower frequencies stunning tends to have higher incidence of defects in the carcasses and turkey breast. The use of high frequencies in stunning, create smaller quantity of trimming, and an increase in turkey breast volume produced, with a financial gain of approximately R$250,000.00 / year. Moreover, there is no need increase the workers to do the trimming tasks and, therefore, higher financial results for companies. Therefore, we recommend the use of high frequencies in the stunning of turkeys.

Tectonoestratigrafia do Terreno Ibérico no sector Tomar- Sardoal-Ferreira do Zêzere e relações com o Terreno Finisterra

A cartografia geológica da região Tomar-Sardoal-Ferreira do Zêzere permitiu individualizar sucessões tectono-estratigráficas em domíníos da Zona Centro-Ibérica (ZCI) e da Zona Ossa Morena (ZOM) que anteriormente eram considerados apenas como ZOM, separadas entre si pelo carreamento de Ortiga-Torrão. A sucessão centro-ibérica monometamórfica, datada do Neoproterozóico ao Silúrico (?), encontra-se numa estrutura triangular e é constituída por unidades típicas do Paleozóico/Neoproterozóico da ZCI. Na ZOM foram estabelecidas duas sucessões polimetamórficas nas regiões do Sardoal e de Serra (Tomar), ambas datadas no geral do Neoproterozóico. A primeira constitui um autóctone relativo e a outra, alóctone; ambas são compostas por unidades deformadas da crosta cadomiana. A continuidade das sucessões tectono-estratigráficas antecedentes do Terreno Ibérico e do carreamento que as limita é interrompida a E pela Zona de Cisalhamento Porto-Tomar-Ferreira do Alentejo (N-S e cinemática direita), a ocidente da qual se encontra o Terreno Finisterra.

Design of unique composites based on aromatic thermosetting copolyesters

Aromatic thermosetting copolyester (ATSP) has promise in high-temperature applications. It can be employed as a bulk polymer, as a coating and as a matrix for carbon fiber composites (ATSP/C composites). This work focuses on the applications of high performance ATSP/C composites. The morphology of the ATSP matrix in the presence of carbon fiber was studied. The effect of liquid crystalline character of starting oligomers used to prepare ATSP on the final crystal structure of the ATSP/C composite was evaluated. Matrices obtained by crosslinking of both liquid crystalline oligomers (ATSP2) and non-liquid crystalline oligomers (ATSP1) tend to crystallize in presence of carbon fibers. The crystallite size of ATSP2 is 4 times that of ATSP1. Composites made from ATSP2 yield tougher matrices compared to those made from ATSP1. Thus toughened matrices could be achieved without incorporating any additives by just changing the morphology of the final polymer. The flammability characteristics of ATSP were also studied. The limiting oxygen index (LOI) of bulk ATSP was found to be 40% whereas that of ATSP/C composites is estimated to be 85%. Thus, ATSP shows potential to be used as a flame resistant material, and also as an aerospace reentry shield. Mechanical properties of the ATSP/C composite were characterized. ATSP was observed to bond strongly with reinforcing carbon fibers. The tensile strength, modulus and shear modulus were comparable to those of conventionally used high temperature epoxy resins. ATSP shows a unique capability for healing of interlaminar cracks on application of heat and pressure, via the Interchain Transesterification Reaction (ITR). ITR can also be used for reduction in void volume and healing of microcracks. Thus, ATSP resin systems provide a unique intrinsic repair mechanism compared to any other thermosetting systems in use today. Preliminary studies on measurement of residual stresses for ATSP/C composites indicate that the stresses induced are much lower than that in epoxy/C composites. Thermal fatigue testing suggests that ATSP shows better resistance to microcracking compared to epoxy resins.

ESTIMATIVAS DAS PROPRIEDADES FÍSICO-MECÂNICAS DE COMPOSTOS LVL CONFECCIONADOS COM PARICÁ POR MEIO DE ULTRASSOM

No presente estudo buscou-se avaliar as propriedades físicas e mecânicas de compostos LVL produzidos com a madeira de paricá ( Schizolobium amazonicum Huber ex. Ducke) por meio do ultrassom. Para isso, foram utilizados LVL produzidos em laboratório e destes retiradas amostras para realização dos ensaios não destrutivos. Posteriormente, as mesmas amostras foram destinadas para realização dos ensaios físicos (absorção de água; inchamento em espessura e inchamento residual) ou mecânicos (resistência e rigidez à flexão estática flatwise; resistência e rigidez à flexão estática edgewise; resistência à compressão paralela e resistência ao cisalhamento paralelo e perpendicular). Os dados da velocidade de propagação de ondas e do módulo de elasticidade dinâmico obtidos nos ensaios não destrutivos foram utilizados no ajuste de equações para estimar as propriedades avaliadas. Os resultados obtidos apontaram o uso do ultrassom como uma ferramenta eficaz para a predição da maior parte das propriedades avaliadas. Dentre as variáveis independentes avaliadas, o módulo de elasticidade dinâmico obteve os melhores resultados quando comparado à velocidade de propagação das ondas.

Características fisico-químicas e sensoriais da carne de bubalinos Murrah abatidos em diferentes períodos de confinamento

Objetivou-se avaliar as características físicas, químicas e sensoriais da carne de búfalos abatidos em diferentes períodos de confinamento. Foram utilizados 20 bubalinos da raça Murrah, castrados, descornados, com idade média inicial de 15 meses, abatidos aos 75, 100, 125 ou 150 dias de confinamento. Após o abate, as carcaças foram identificadas e resfriadas por 24 horas. Durante a desossa, foram colhidas amostras do contrafilé entre a 10ª e 11ª costelas para análise das características sensoriais e das perdas por cocção; entre a 11ª e 12ª costelas para avaliação da composição centesimal, do valor calórico, do pH e do índice de fragmentação miofibrilar (IFM); e entre a 12ª e 13ª costelas para a avaliação do escore de marmorização e da força de cisalhamento. A composição centesimal, o pH, a força de cisalhamento, o valor calórico, as perdas por cocção e o IFM não diferiram estatisticamente entre os períodos de confinamento. O grau de marmorização diferiu entre as idades de abate, uma vez os animais abatidos aos 75 dias de confinamento apresentaram escore de 1,25; os abatidos aos 100 e 125 dias, escore 2; e aqueles abatidos aos 150 dias de confinamento, escore 2,2. em todos os períodos de confinamento, a carne bubalina foi classificada como macia (média 3,94 kgf) e apresentou com características que não diferiram pelo painel sensorial entre os 75 e 150 dias de confinamento. O abate de bubalinos aos 75 e 150 dias de confinamento não influencia as características sensoriais sabor, aroma e cor da carne bubalina.

Desevolvimento de nanocompósitos de poli(metacrilato de metila)/argila processados por mistura no estado fundido

Poly(methyl methacrylate)/clay nanocomposites were prepared by melt mixing using a montmorillonite-rich clay (MMT). The clay in natura was treated with acrylic acid to facilitate the dispersion in the polymer matrix. A masterbatch of PMMA/clay was prepared and combined with the pure PMMA and then subjected to extrusion process using singlescrew and twin-screw extruders followed by injection. Nanocomposites were processed with clay contents of 1, 3, 5 and 8 wt.%. The effect of shear processing on the morphology of the nanocomposites was evaluated by XRD, SEM and TEM. Thermal and mechanical properties of the nanocomposites were investigated through TGA, DSC, HDT, VICAT, tensile and impact tests, to evaluate the effect of the addition of clay to the PMMA matrix. Flammability tests were also conducted to investigate the effect of the addition of clay on the flame retardation properties. SEM images of the nanocomposites indicated the presence of clay agglomerates, which resulted in the reduction of properties such as thermal stability, mechanical strength and impact resistance, and increased the rate of burning for materials processed by both extrusion routes

Fabricación y caracterización físico-mecánica de biocomposites reforzados con fibras naturales. Aplicaciones en el sector náutico.

156 p.