An Acoustic Analysis of Valveless Pulsejet Engines

Valveless pulsejets are extremely simple aircraft engines; essentially cleverly designed tubes with no moving parts. These engines utilize pressure waves, instead of machinery, for thrust generation, and have demonstrated thrust-to-weight ratios over 8 and thrust specific fuel consumption levels below 1 lbm/lbf-hr – performance levels that can rival many gas turbines. Despite their simplicity and competitive performance, they have not seen widespread application due to extremely high noise and vibration levels, which have persisted as an unresolved challenge primarily due to a lack of fundamental insight into the operation of these engines. This thesis develops two theories for pulsejet operation (both based on electro-acoustic analogies) that predict measurements better than any previous theory reported in the literature, and then uses them to devise and experimentally validate effective noise reduction strategies. The first theory analyzes valveless pulsejets as acoustic ducts with axially varying area and temperature. An electro-acoustic analogy is used to calculate longitudinal mode frequencies and shapes for prescribed area and temperature distributions inside an engine. Predicted operating frequencies match experimental values to within 6% with the use of appropriate end corrections. Mode shapes are predicted and used to develop strategies for suppressing higher modes that are responsible for much of the perceived noise. These strategies are verified experimentally and via comparison to existing models/data for valveless pulsejets in the literature. The second theory analyzes valveless pulsejets as acoustic systems/circuits in which each engine component is represented by an acoustic impedance. These are assembled to form an equivalent circuit for the engine that is solved to find the frequency response. The theory is used to predict the behavior of two interacting pulsejet engines. It is validated via comparison to experiment and data in the literature. The technique is then used to develop and experimentally verify a method for operating two engines in anti-phase without interfering with thrust production. Finally, Helmholtz resonators are used to suppress higher order modes that inhibit noise suppression via anti-phasing. Experiments show that the acoustic output of two resonator-equipped pulsejets operating in anti-phase is 9 dBA less than the acoustic output of a single pulsejet.

Automated Discovery of Social Networks in Online Learning Communities

As a way to gain greater insights into the operation of online communities, this dissertation applies automated text mining techniques to text-based communication to identify, describe and evaluate underlying social networks among online community members. The main thrust of the study is to automate the discovery of social ties that form between community members, using only the digital footprints left behind in their online forum postings. Currently, one of the most common but time consuming methods for discovering social ties between people is to ask questions about their perceived social ties. However, such a survey is difficult to collect due to the high investment in time associated with data collection and the sensitive nature of the types of questions that may be asked. To overcome these limitations, the dissertation presents a new, content-based method for automated discovery of social networks from threaded discussions, referred to as ‘name network’. As a case study, the proposed automated method is evaluated in the context of online learning communities. The results suggest that the proposed ‘name network’ method for collecting social network data is a viable alternative to costly and time-consuming collection of users’ data using surveys. The study also demonstrates how social networks produced by the ‘name network’ method can be used to study online classes and to look for evidence of collaborative learning in online learning communities. For example, educators can use name networks as a real time diagnostic tool to identify students who might need additional help or students who may provide such help to others. Future research will evaluate the usefulness of the ‘name network’ method in other types of online communities.

Elfas und Ahlsburg - die Struktur der Schollengrenze zwischen Hils und Solling

The Elfas, Ahlsburg, and Salzderhelden overthrusts have been considered for a long time to be halotectonic structures caused by diapiric rise of Zechstein salt into thrust planes and other zones of weakness in the overlying rocks. Much of the Markoldendorf syncline between the overthrusts is covered by Quaternary deposits. The structure of the syncline and its western and southern boundaries were mapped with the help of many boreholes and micropalaeontological dating during remapping of the 1 : 25 000 geological sheet 4124 (Dassel). The Ahlsburg overthrust has now been shown to continue to the NW and to lead into the Lüthorst graben, which truncates the syncline in the west and passes into the crestal fault of the Elfas anticline. Figure 6 shows the NW-SE trending faults bounding three blocks which, according to seismic interpretation (Geotectonic Atlas 1996), have moved several times, in some areas in opposite senses. The NNE-SSW-trending grabens act as hinges, separating the NW-SE faults into sections that have undergone different movement.

Tidal Energy ”Round Robin” Tests Comparisons between towing tank and circulating tank results

One key step of the industrial development of a tidal energy device is the testing of scale prototype devices within a controlled laboratory environment. At present, there is no available experimental protocol which addresses in a quantitative manner the differences which can be expected between results obtained from the different types of facilities currently employed for this type of testing. As a consequence, where differences between results are found it has been difficult to confirm the extent to which these differences relate to the device performance or to the test facility type. In the present study, a comparative ”Round Robin” testing programme has been conducted as part of the EC FP VII MaRINET program in order to evaluate the impact of different experimental facilities on the test results. The aim of the trials was to test the same model tidal turbine in four different test facilities to explore the sensitivity of the results to the choice of facility. The facilities comprised two towing tanks, of very different size, and two circulating water channels. Performance assessments in terms of torque, drag and inflow speed showed very similar results in all facilities. However, expected differences between the different tank types (circulating and towing) were observed in the fluctuations of torque and drag measurements. The main facility parameters which can influence the behaviour of the turbine were identified; in particular the effect of blockage was shown to be significant in cases yielding for high thrust coefficients, even at relatively small blockage ratios.

Tectono-metamorphic evolution of a nappe stack: A case study of the Swiss Alps

Fold-and-thrust belts are prominent structures that occur at the front of compressional orogens. To unravel the tectonic and metamorphic evolution of such complexes, kinematic investigations, quantitative microstructural analysis and geothermometry (calcite–graphite, calcite–dolomite) were performed on carbonate mylonites from thrust faults of the Helvetic nappe stack in Central Switzerland. Paleo-isotherms of peak temperature conditions and cooling stages (fission track) of the nappe pile were reconstructed in a vertical section and linked with the microstructural and kinematic evolution. Mylonitic microstructures suggest that under metamorphic conditions close to peak temperature, strain was highly localized within thrust faults where deformation temperatures spatially continuously increased in both directions, from N to S within each nappe and from top–down in the nappe stack, covering a temperature range of 180–380 °C. Due to the higher metamorphic conditions, thrusting of the lowermost nappe, the Doldenhorn nappe, was accompanied by a much more pronounced nappe internal ductile deformation of carbonaceous rock types than was the case for the overlying Wildhorn- and Gellihorn nappes. Ongoing thrusting brought the Doldenhorn nappe closer to the surface. The associated cooling resulted in a freezing in of the paleo-isotherms of peak metamorphic conditions. Contemporaneous shearing localized in the basal thrust, initially still in the ductile deformation regime and finally as brittle faulting and cataclasis inducing ultimately an inverse metamorphic zonation. With ongoing exhumation and the formation of the Helvetic antiformal nappe stack, a bending of large-scale tectonic structures (thrusts, folds), peak temperature isotherms and cooling isotherms occurred. While this local bending can directly be attributed to active deformation underneath the section investigated up to times of 2–3 ma, a more homogeneous uplift of the entire region is suggested for the very late and still active exhumation stage.

Collimation of deuterium / 3-helium fusion products for advanced spacecraft propulsion and power

Current space exploration has transpired through the use of chemical rockets, and they have served us well, but they have their limitations. Exploration of the outer solar system, Jupiter and beyond will most likely require a new generation of propulsion system. One potential technology class to provide spacecraft propulsion and power systems involve thermonuclear fusion plasma systems. In this class it is well accepted that d-He3 fusion is the most promising of the fuel candidates for spacecraft applications as the 14.7 MeV protons carry up to 80% of the total fusion power while ‘s have energies less than 4 MeV. The other minor fusion products from secondary d-d reactions consisting of 3He, n, p, and 3H also have energies less than 4 MeV. Furthermore there are two main fusion subsets namely, Magnetic Confinement Fusion devices and Inertial Electrostatic Confinement (or IEC) Fusion devices. Magnetic Confinement Fusion devices are characterized by complex geometries and prohibitive structural mass compromising spacecraft use at this stage of exploration. While generating energy from a lightweight and reliable fusion source is important, another critical issue is harnessing this energy into usable power and/or propulsion. IEC fusion is a method of fusion plasma confinement that uses a series of biased electrodes that accelerate a uniform spherical beam of ions into a hollow cathode typically comprised of a gridded structure with high transparency. The inertia of the imploding ion beam compresses the ions at the center of the cathode increasing the density to the point where fusion occurs. Since the velocity distributions of fusion particles in an IEC are essentially isotropic and carry no net momentum, a means of redirecting the velocity of the particles is necessary to efficiently extract energy and provide power or create thrust. There are classes of advanced fuel fusion reactions where direct-energy conversion based on electrostatically-biased collector plates is impossible due to potential limits, material structure limitations, and IEC geometry. Thermal conversion systems are also inefficient for this application. A method of converting the isotropic IEC into a collimated flow of fusion products solves these issues and allows direct energy conversion. An efficient traveling wave direct energy converter has been proposed and studied by Momota , Shu and further studied by evaluated with numerical simulations by Ishikawa and others. One of the conventional methods of collimating charged particles is to surround the particle source with an applied magnetic channel. Charged particles are trapped and move along the lines of flux. By introducing expanding lines of force gradually along the magnetic channel, the velocity component perpendicular to the lines of force is transferred to the parallel one. However, efficient operation of the IEC requires a null magnetic field at the core of the device. In order to achieve this, Momota and Miley have proposed a pair of magnetic coils anti-parallel to the magnetic channel creating a null hexapole magnetic field region necessary for the IEC fusion core. Numerically, collimation of 300 eV electrons without a stabilization coil was demonstrated to approach 95% at a profile corresponding to Vsolenoid = 20.0V, Ifloating = 2.78A, Isolenoid = 4.05A while collimation of electrons with stabilization coil present was demonstrated to reach 69% at a profile corresponding to Vsolenoid = 7.0V, Istab = 1.1A, Ifloating = 1.1A, Isolenoid = 1.45A. Experimentally, collimation of electrons with stabilization coil present was demonstrated experimentally to be 35% at 100 eV and reach a peak of 39.6% at 50eV with a profile corresponding to Vsolenoid = 7.0V, Istab = 1.1A, Ifloating = 1.1A, Isolenoid = 1.45A and collimation of 300 eV electrons without a stabilization coil was demonstrated to approach 49% at a profile corresponding to Vsolenoid = 20.0V, Ifloating = 2.78A, Isolenoid = 4.05A 6.4% of the 300eV electrons’ initial velocity is directed to the collector plates. The remaining electrons are trapped by the collimator’s magnetic field. These particles oscillate around the null field region several hundred times and eventually escape to the collector plates. At a solenoid voltage profile of 7 Volts, 100 eV electrons are collimated with wall and perpendicular component losses of 31%. Increasing the electron energy beyond 100 eV increases the wall losses by 25% at 300 eV. Ultimately it was determined that a field strength deriving from 9.5 MAT/m would be required to collimate 14.7 MeV fusion protons from d-3He fueled IEC fusion core. The concept of the proton collimator has been proven to be effective to transform an isotropic source into a collimated flow of particles ripe for direct energy conversion.

The influence of nano-scale second-phase particles on deformation of fine grained calcite mylonites

Grey and white carbonate mylonites were collected along thrust planes of the Helvetic Alps. They are characterised by very small grain sizes and non-random grain shape (SPO) and crystallographic preferred orientation (CPO). Presumably they deformed in the field of grain size sensitive flow by recrystallisation accommodated intracrystalline deformation in combination with granular flow. Both mylonites show a similar mean grain size, but in the grey mylonites the grain size range is larger, the grain shapes are more elongate and the dynamically recrystallised calcite grains are more often twinned. Grey mylonites have an oblique CPO, while the CPO in white mylonites is symmetric with respect to the shear plane. Combustion analysis and TEM investigations revealed that grey mylonites contain a higher amount of highly structured kerogens with particle sizes of a few tens of nanometers, which are finely dispersed at the grain boundaries. During deformation of the rock, nano-scale particles reduced the migration velocity of grain boundaries by Zener drag resulting in slower recrystallisation rates of the calcite aggregate. In the grey mylonites, more strain increments were accommodated by individual grains before they became refreshed by dynamic recrystallisation than in white mylonites, where grain boundary migration was less hindered and recrystallisation cycles were faster. Consequently, grey mylonites represent ‘deformation’ microfabrics while white mylonites are characterised by ‘recrystallisation’ microfabrics. Field geologists must utilise this different deformation behavior when applying the obliquity in CPO and SPO of the respective mylonites as reliable shear sense indicators.

Morfoestruturas quilométricas em forma de crescente nas águas profundas do Golfo de Cádis

O levantamento batimétrico MATESPRO, realizado no NW do Golfo de Cádis, revelou a existência de intrigantes objectos morfológicos jacentes entre os 4300 e os 4700 metros de profundidade. Estes objectos, de dimensões quilométricas, são constituídos por uma depressão interna limitada parcialmente por uma escarpa em forma em crescente que pode atingir mais de 100 m de altura, com declives que variam entre os 6 e os 27° e cuja parte interna é constituída por uma depressão preenchida por unidades progradantes, que se desenvolvem no sentido da escarpa. Estes objectos são interpretados como o resultado da acção conjunta de processos tectónicos e sedimentares e da sua interacção com correntes de fundo. A actividade tectónica gera rupturas de declive no fundo do mar. As correntes de fundo e turbidíticas interagem com estas irregularidades morfológicas, amplificando-as através da sua acção erosiva, permitindo assim a criação das escarpas abruptas dos crescentes e a formação de corpos sedimentares progradantes. ABSTRACT; Multi-beam swath bathymetry carried out in NW Gulf of Cadiz revealed several intriguing features, lying at depths between -4300 and- 4700 m. These features display kilometric crescent escarpments up to 100 m high with slopes between 6 and 27 degrees, in an area characterized by very shallow general slope gradients (0,5 °). The internal part of a Crescent consists of a depression filled up with upslope prograding drift developing towards the scarp. These features are interpreted as the coupled result of sedimentary and tectonic processes. It is proposed that the Crescents formed when a local morphologic irregularity, corresponding to the bathymetric expression of movement on an underlying thrust, is enhanced by the erosional activity of turbidity and bottom currents. The drift results from the re-deposition of the eroded material in the same location.

Mesh Adaption for Tracking Vortex Structures in OVERTURNS Simulation of the S-76 Rotor in Hover

The constant need to improve helicopter performance requires the optimization of existing and future rotor designs. A crucial indicator of rotor capability is hover performance, which depends on the near-body flow as well as the structure and strength of the tip vortices formed at the trailing edge of the blades. Computational Fluid Dynamics (CFD) solvers must balance computational expenses with preservation of the flow, and to limit computational expenses the mesh is often coarsened in the outer regions of the computational domain. This can lead to degradation of the vortex structures which compose the rotor wake. The current work conducts three-dimensional simulations using OVERTURNS, a three-dimensional structured grid solver that models the flow field using the Reynolds-Averaged Navier-Stokes equations. The S-76 rotor in hover was chosen as the test case for evaluating the OVERTURNS solver, focusing on methods to better preserve the rotor wake. Using the hover condition, various computational domains, spatial schemes, and boundary conditions were tested. Furthermore, a mesh adaption routine was implemented, allowing for the increased refinement of the mesh in areas of turbulent flow without the need to add points to the mesh. The adapted mesh was employed to conduct a sweep of collective pitch angles, comparing the resolved wake and integrated forces to existing computational and experimental results. The integrated thrust values saw very close agreement across all tested pitch angles, while the power was slightly over predicted, resulting in under prediction of the Figure of Merit. Meanwhile, the tip vortices have been preserved for multiple blade passages, indicating an improvement in vortex preservation when compared with previous work. Finally, further results from a single collective pitch case were presented to provide a more complete picture of the solver results.

Hyperlinks in e-books : expanding the functionality of end-notes

With its powerful search engines and billions of published pages, the Worldwide Web has become the ultimate tool to explore the human experience. But, despite the advent of the digital revolution, e-books, at their core, have remained remarkably similar to their printed siblings. This has resulted in a clear dichotomy between two ways of reading: on one side, the multi-dimensional world of the Web; on the other, the linearity of books and e-books. My investigation of the literature indicates that the focus of attempts to merge these two modes of production, and hence of reading, has been the insertion of interactivity into fiction. As I will show in the Literature Review, a clear thrust of research since the early 1990s, and in my opinion the most significant, has concentrated on presenting the reader with choices that affect the plot. This has resulted in interactive stories in which the structure of the narrative can be altered by the reader of experimental fiction. The interest in this area of research is not surprising, as the interaction of readers with the fabric of the narrative provides a fertile ground for exploring, analysing, and discussing issues of plot consistency and continuity. I found in the literature several papers concerned with the effects of hyperlinking on literature, but none about how hyperlinked material and narrative could be integrated without compromising the narrative flow as designed by the author. It led me to think that the researchers had accepted hypertextuality and the linear organisation of fiction as being antithetical, thereby ignoring the possibility of exploiting the first while preserving the second. All the works I consulted were focussed on exploring the possibilities provided to authors (and readers) by hypertext or how hypertext literature affects literary criticism. This was true in earlier works by Landow and Harpold and remained true in later works by Bolter and Grusin. To quote another example, in his book Hypertext 3.0, Landow states: “Most who have speculated on the relation between hypertextuality and fiction concentrate [...] on the effects it will have on linear narrative”, and “hypertext opens major questions about story and plot by apparently doing away with linear organization” (Landow, 2006, pp. 220, 221). In other words, the authors have added narrative elements to Web pages, effectively placing their stories in a subordinate role. By focussing on “opening up” the plots, the researchers have missed the opportunity to maintain the integrity of their stories and use hyperlinked information to provide interactive access to backstory and factual bases. This would represent a missing link between the traditional way of reading, in which the readers have no influence on the path the author has laid out for them, and interactive narrative, in which the readers choose their way across alternatives, thereby, at least to a certain extent, creating their own path. It would be, to continue the metaphor, as if the readers could follow the main path created by the author while being able to get “sidetracked” into exploring hyperlinked material. In Hypertext 3.0, Landow refers to an “Axial structure [of hypertext] characteristic of electronic books and scholarly books with foot-and endnotes” versus a “Network structure of hypertext” (Landow, 2006, p. 70). My research aims at generalising the axial structure and extending it to fiction without losing the linearity at its core. In creative nonfiction, the introduction of places, scenes, and settings, together with characterisation, brings to life the facts without altering them; while much fiction draws on facts to provide a foundation, or narrative elements, for the work. But how can the reader distinguish between facts and representations? For example, to what extent do dialogues and perceptions present what was actually said and thought? Some authors of creative nonfiction use end-notes to provide comments and citations while minimising disruption the flow of the main text, but they are limited in scope and constrained in space. Each reader should be able to enjoy the narrative as if it were a novel but also to explore the facts at the level of detail s/he needs. For this to be possible, end-notes should provide a Web-like way of exploring in more detail what the author has already researched. My research aims to develop ways of integrating narrative prose and hyperlinked documents into a Hyperbook. Its goal is to create a new writing paradigm in which a story incorporates a gateway to detailed information. While creative nonfiction uses the techniques of fictional writing to provide reportage of actual events and fact-based fiction illuminates the affectual dimensions of what happened (e.g., Kate Grenville’s The Secret River and Hilary Mantel’s Wolf Hall), Hyperbooks go one step further and link narrative prose to the details of the events on which the narrative is based or, more in general, to information the reader might find of interest. My dissertation introduces and utilises Hyperbooks to engage in two parallel types of investigation Build knowledge about Italian WWII POWs held in Australia and present it as part of a novella in Hyperbook format. Develop a new piece of technology capable of extending the writing and reading process.

Complications associated with closing wedge ostectomy procedure for treatment of cranial cruciate ligament rupture in dogs : a retrospective study of 145 cases

Dissertação de Mestrado Integrado em Medicina Veterinária

Turning conflict into coexistence: cross-cutting ties and institutions in the agro-pastoral borderlands of Lake Naivasha basin, Kenya

The Maasai/Kikuyu agro-pastoral borderlands of Maiella and Enoosupukia, located in the hinterlands of Lake Naivasha’s agro-industrial hub, are particularly notorious in the history of ethnicised violence in the Kenya’s Rift Valley. In October 1993, an organised assault perpetrated by hundreds of Maasai vigilantes, with the assistance of game wardens and administration police, killed more than 20 farmers of Kikuyu descent. Consequently, thousands of migrant farmers were violently evicted from Enoosupukia at the instigation of leading local politicians. Nowadays, however, intercommunity relations are surprisingly peaceful and the cooperative use of natural resources is the rule rather than the exception. There seems to be a form of reorganization. Violence seems to be contained and the local economy has since recovered. This does not mean that there is no conflict, but people seem to have the facility to solve them peacefully. How did formerly violent conflicts develop into peaceful relations? How did competition turn into cooperation, facilitating changing land use? This dissertation explores the value of cross-cutting ties and local institutions in peaceful relationships and the non-violent resolution of conflicts across previously violently contested community boundaries. It mainly relies on ethnographic data collected between 2014 and 2015. The discussion therefore builds on several theoretical approaches in anthropology and the social sciences – that is, violent conflicts, cross-cutting ties and conflicting loyalties, joking relationships, peace and nonviolence, and institutions, in order to understand shared spaces that are experiencing fairly rapid social and economic changes, and characterised by conflict and coexistence. In the researched communities, cross-cutting ties and the split allegiances associated with them result from intermarriages, land transactions, trade, and friendship. By institutions, I refer to local peace committees, an attempt to standardise an aspect of customary law, and Nyumba Kumi, a strategy of anchoring community policing at the household level. In 2010, the state “implanted” these grassroots-level institutions and conferred on them the rights to handle specific conflicts and to prevent crime. I argue that the studied groups utilise diverse networks of relationships as adaptive responses to landlessness, poverty, and socio-political dynamics at the local level. Material and non-material exchanges and transfers accompany these social and economic ties and networks. In addition to being instrumental in nurturing a cohesive social fabric, I argue that such alliances could be thought of as strategies of appropriation of resources in the frontiers – areas that are considered to have immense agricultural potential and to be conducive to economic enterprise. Consequently, these areas are continuously changed and shaped through immigration, population growth, and agricultural intensification. However, cross-cutting ties and intergroup alliances may not necessarily prevent the occurrence or escalation of conflicts. Nevertheless, disputes and conflicts, which form part of the social order in the studied area, create the opportunities for locally contextualised systems of peace and non-violence that inculcate the values of cooperation, coexistence, and restraint from violence. Although the neo-traditional institutions (local peace committees and Nyumba Kumi) face massive complexities and lack the capacity to handle serious conflicts, their application of informal constraints in dispute resolution provides room for some optimism. Notably, the formation of ties and alliances between the studied groups, and the use of local norms and values to resolve disputes, are not new phenomena – they are reminiscent of historical patterns. Their persistence, particularly in the context of Kenya, indicates a form of historical continuity, which remains rather “undisturbed” despite the prevalence of ethnicised political economies. Indeed, the formation of alliances, which are driven by mutual pursuit of commodities (livestock, rental land, and agricultural produce), markets, and diversification, tends to override other identities. While the major thrust of social science literature in East Africa has focused on the search for root causes of violence, very little has been said about the conditions and practices of cooperation and non-violent conflict resolution. In addition, situations where prior violence turned into peaceful interaction have attracted little attention, though the analysis of such transitional phases holds the promise of contributing to applicable knowledge on conflict resolution. This study is part of a larger multidisciplinary project, “Resilience in East African Landscapes” (REAL), which is a Marie Curie Actions Innovative Training Networks (ITN) project. The principal focus of this multidisciplinary project is to study past, present, and future thresholds and sustainable trajectories in human-landscape interactions in East Africa over the last millennia. While other individual projects focus on long-term ecosystem dynamics and societal interactions, my project examines human-landscape interactions in the present and the very recent past (i.e. the period in which events and processes were witnessed or can still be recalled by today’s population). The transition from conflict to coexistence and from competition to cooperative use of previously violently contested land resources is understood here as enhancing adaptation in the face of social-political, economic, environmental, and climatic changes. This dissertation is therefore a contribution to new modes of resilience in human-landscape interactions after a collapse situation.

Tectonic evolution of Variscan Iberia: Gondwana–Laurussia

An integrated interpretation of the late Paleozoic structural and geochronological record of the Iberian Massif is presented and discussed under the perspective of a Gondwana-Laurussia collision giving way to the Variscan orogen. Compressional and extensional structures developed during the building of the Variscan orogenic crust of Iberia are linked together into major tectonic events operating at lithosphere scale. A review of the tectonometamorphic and magmatic evolution of the IberianMassif reveals backs and forths in the overall conver- gence between Gondwana and Laurussia during theamalgamation of Pangea in late Paleozoic times. Stages dom- inated by lithosphere compression are characterized by subduction, both oceanic and continental, development of magmatic arcs, (over- and under-) thrusting of continental lithosphere, and folding. Variscan convergence re- sulted in the eventual transference of a large allochthonous set of peri-Gondwanan terranes, the Iberian Allochthon, onto the Gondwana mainland. The Iberian Allochthon bears the imprint of previous interaction be- tween Gondwana and Laurussia, including their juxtaposition after the closure of the Rheic Ocean in Lower De- vonian times. Stages governed by lithosphere extension are featured by the opening of two short-lived oceanic basins that dissected previous Variscan orogenic crust, first in the Lower-Middle Devonian, following the closure of the Rheic Ocean, and then in the early Carboniferous, following the emplacement of the peri-Gondwanan allochthon. An additional, major intra-orogenic extensional event in the early-middle Carboniferous dismem- bered the Iberian Allochthon into individual thrust stacks separated by extensional faults and domes. Lateral tec- tonics played an important role through the Variscan orogenesis, especially during the creation of new tectonic blocks separated by intracontinental strike-slip shear zones in the late stages of continental convergence.