Evaluation of the efficacy of commercial sanitizers against adhered and planktonic cells of Listeria monocytogenes and Salmonella spp.

Antimicrobial activities of two commercial disinfectants, alone or combined with heat, against three Salmonella strains and three Listeria monocytogenes strains were studied. The efficacy of disinfectants against planktonic bacteria and bacteria attached to three food contact industrial surfaces (stainless steel, polytetraflourethylene, and rubber) was investigated. The tests were conducted using the sanitizer (quaternary ammonium compounds, and alquyldiethylenediamineglycine and di-alquyldiamineethylglycine) concentrations recommended by the manufacturers, and concentrations twice and four times higher than those values. The recommended concentrations were not effective to kill bacteria, especially when they were attached to surfaces. Concentrations of disinfectants twice and four times higher than those recommended were needed to fully eliminate planktonic bacteria. These same sanitizer concentrations were not sufficient to remove attached bacteria. To remove them from the surfaces, a treatment with recommended concentrations in combination with heat was needed. Our results indicate that these two pathogenic bacteria could survive common sanitation programs used in the food industry.

Underwater Remote Welding Technology for Offshore Structures

The construction of offshore structures, equipment and devices requires a high level of mechanical reliability in terms of strength, toughness and ductility. One major site for mechanical failure, the weld joint region, needs particularly careful examination, and weld joint quality has become a major focus of research in recent times. Underwater welding carried out offshore faces specific challenges affecting the mechanical reliability of constructions completed underwater. The focus of this thesis is on improvement of weld quality of underwater welding using control theory. This research work identifies ways of optimizing the welding process parameters of flux cored arc welding (FCAW) during underwater welding so as to achieve desired weld bead geometry when welding in a water environment. The weld bead geometry has no known linear relationship with the welding process parameters, which makes it difficult to determine a satisfactory weld quality. However, good weld bead geometry is achievable by controlling the welding process parameters. The doctoral dissertation comprises two sections. The first part introduces the topic of the research, discusses the mechanisms of underwater welding and examines the effect of the water environment on the weld quality of wet welding. The second part comprises four research papers examining different aspects of underwater wet welding and its control and optimization. Issues considered include the effects of welding process parameters on weld bead geometry, optimization of FCAW process parameters, and design of a control system for the purpose of achieving a desired bead geometry that can ensure a high level of mechanical reliability in welded joints of offshore structures. Artificial neural network systems and a fuzzy logic controller, which are incorporated in the control system design, and a hybrid of fuzzy and PID controllers are the major control dynamics used. This study contributes to knowledge of possible solutions for achieving similar high weld quality in underwater wet welding as found with welding in air. The study shows that carefully selected steels with very low carbon equivalent and proper control of the welding process parameters are essential in achieving good weld quality. The study provides a platform for further research in underwater welding. It promotes increased awareness of the need to improve the quality of underwater welding for offshore industries and thus minimize the risk of structural defects resulting from poor weld quality.

Prosessiteollisuuden sekoittimen elinkaariarviointi

Työn tavoitteena oli tehdä elinkaariarviointi (LCA) prosessiteollisuuden sekoittimelle Helmix HF-80 ja analysoida LCA-tulokset, vaikutus ilmaston lämpenemisen potentiaalin (GWP) suhteen, sekä tutkia GWP-vaikutuksen pienentämisen mahdollisuuksia. Tutkittavan sekoittimen mahdolliset käyttökohteet ovat sellu- ja paperiteollisuus, raskaiden jätenesteiden käsittely, sekä muut teollisuusalueet, joissa käytetään tämän tyyppisiä laitteita. Työssä on muun muassa käsitelty sekoitusprosessit, sekoituslaitteiden tyypit, niiden rakenteiden ominaisuudet, käyttötarkoitus, toimintaperiaatteet, sekä sellu- ja paperi-teollisuudessa käytettävien sekoittimien yleiskatsaus. Työssä on myös kuvattu elinkaariarviointi (LCA) -menetelmä ja sen käyttötarkoitus. Tärkeimmistä tuloksista voi mainita sen, että sekoittimen (ilman säiliötä, sähkömoottoria ja vaihteistoa) kokoelinkaaren ilmastonlämpenemisen potentiaali (GWP) on noin 750 000 kg CO2-Equiv. Sekoittimen tuotanto- ja kierrätysaikana syntyy vain 1200 kg CO2-Equiv. ja suurin osa 748 000 kg CO2-Equiv. johtuu sähköenergian kulutuksesta käytön aikana. Käyttöajan vaikutusta voisi pienentää arvoksi 0 kg CO2-Equiv. käyttämällä pelkästään uusiutuvaa energiaa. Jos tuotantoaikana käytetty energia myös korvataan uusiutuvalla energialla, niin GWP-arvo koko elinkaaren aikana laskee arvoon 1006 kg CO2eqv., mikä on vain 0,13 % saaduista tuloksista. Suurin osa tästä arvosta liittyy sekoittimen materiaalin, tässä tapauksessa ruostumattoman teräksen tuotantoon.

Suurlujuusterästen hitsausliitoksen muutosvyöhykkeen metallurgiset muutokset

Tässä kandidaatintyössä käsitellään suurlujuusteräksiä ja niiden hitsausta, keskittyen varsinkin hitsauksessa perusaineeseen syntyvään muutosvyöhykkeeseen. Työn alkuosio on suoritettu kirjallisuustutkimuksena ja siinä käydään läpi yleisesti suurlujuusterästen määrittelyä, valmistustapoja, hitsausta ja hitsaukseen liittyviä erityisnäkökohtia. Työn loppuosassa on tutustuttu suurlujuusteräksiä hitsattaessa syntyvään muutosvyöhykkeeseen koehitsien avulla. Suurlujuusteräksille ei ole luotu yleistä standardisoitua määrittelyasteikkoa, mutta teräksiä aletaan usein pitämään suurlujuusteräksinä kun niiden myötöraja ylittään 460–550 MPa. Tällaisia teräksiä voidaan valmistaa pääasiassa joko nuorruttamalla, termomekaanisesti valssaamalla tai suorakarkaisemalla. Valmistustavalla on suuri vaikutus teräksen hitsattavuuteen. Nuorrutetuille teräksille hitsattaessa muodostuvan muutosvyöhykkeen karkearakeisen osion raekoko voi kasvaa huomattavasti varsinkin suurempia lämmöntuonteja käytettäessä ja täten aiheuttaa merkittävääkin kovuuden kasvua, kuten myös tämän kandidaatintyön koehitseissä havaittiin. Termomekaanisesti valmistetuilla teräksillä ei vastaavanlaista kovuuden kasvua yleensä ilmene. Valmistustavasta riippumatta suurlujuusterästen mekaaniset ominaisuudet vaikuttaisivat heikentyvän kyseisellä vyöhykkeellä suurempia lämmöntuonteja käytettäessä. Suurlujuusterästen hitsausliitosten laatua pyritäänkin parantamaan jatkuvasti esimerkiksi kehittämällä materiaaleista paremmin hitsattavia ja hitsausprosesseista paremmin suurlujuusteräksien erityistarpeita huomioivia.

Geochemistry and mineralogical association of heavy metal contaminants in fine grained sediment, Welland River, Southern Ontario /

This investigation of geochemistry and mineralogy of heavy metals in fine grained (<63^m) sediment of the Welland River was imdertaken to: 1) describe metal dispersion patterns relative to a source, identify minerals forming and existing at the outfall region and relate sediment particle size to chemistry; 2) to delineate sample handling, preparation and evaluate, modify and develop analytical methods for heavy metal analysis of complex environmental samples. Ajoint project between Brock University and Geoscience Laboratories was initiated to test a contaminated site of the Welland River at the base of Atlas Speciality Steels Co. Methods were developed and utilized for particle size separation and two acid extraction techniques: 1) Partial extraction; 2) Total extraction. The mineralogical assessment identified calcite, dolomite, quartz and clays. These minerals are typical of the carbonate-shale rock basement of the Niagara Peninsula. Minerals such as, mullite and ferrocolumbite were found at the outfall region. These are not typical of the local geology and are generally associated with industrial pollutants. Partial and total extraction techniques were used to characterize the sediments based on chemical distribution, elemental behaviour and analytical differences. The majority of elements were lower in concentration in the partial extraction technique; suggesting these elements are bound in an acid extractable phase (exchangeable, organic and carbonate phases). The total extraction technique yielded higher elemental concentrations taking difficult oxides and silicates into solution. Geochemical analyses of grain size separates revealed that heavy metal (Co, Ni, V, Mn, Fe, Ba) concentrations did not increase with decreasing grain size. This is a function of the anthropogenic mill scale input into the river. The background elements (Sc, Y, Sr, Mg, Al and Ti) showed an increase in concentration to the finest grain size suggesting that it is directly related to the local mineralogy and geology. Dispersion patterns ofmetals fall into two distinct categories: 1) the heavy metals (Co, Cu, Ni, Zn, V and Cr), and 2) the background elements (Be, Sc, Y, Sr, Al and Ti). The heavy metals show a marked increase in the outfall region, while the background elements show a significant decrease at the outfall. This pattern is attributed to a "dilution effect" ofthe natural sediments by the anthropogenic mill scale sediments. Multivariant statistical analysis and correlation coefficient matrix results clearly support these results and conclusions. These results indicate the outfall region ofthe Welland River is highly contaminated with to heavy metals from the industrialized area of Welland. A short distance downstream, the metal concentrations return to baseline geochemical levels. It appears, contaminants rapidly come out of suspension and are deposited in close proximity to the source. Therefore, it is likely that dredging the sediment from the river may cause resuspension of contaminated sediments, but may not distribute the sediment as far as initially anticipated.

The role of the GABAergic system in the production of ultrasonic vocalization in rats /

Ultrasonic vocalization plays an important role in intraspecies communication for rats. It has been well demonstrated that rats will emit 22kHz vocalization in stressfiil or threatening situations. Although the neural mechanism underlying vocahzation is not well understood, it is known that chohnergic input to the basal forebrain induces such alarm calls. A number of experiments have found that intracerebral injection of carbachol, a predominantly muscarinic agonist, into die anterior hypothalamic/preoptic area (AH/POA) rehably induces vocalization similar to naturally emitted ultrasonic calls. It has also been shown that carbachol has extensive inhibitory effects on neuronal firing in the same area. This result impUes that the inhibitory effects of carbachol in the AH/POA could trigger vocahzation, and that the GABAergic system could be involved. The purpose of this study is to investigate the effects ofGABA agonists and antagonists on flie production of carbachol induced 22kHz vocalization. The following hypotheses were examined: 1) apphcation ofGABA (a naturally occurring inhibitory neurotransmitter) will have a synergistic effect with carbachol, increasing vocalization; and 2) tiie apphcation ofGABA antagonists (picrotoxin or bicuculline) will reduce caibachol-induced vocalization. A total of sixty rats were implanted with stainless steel guide cannulae in the AH/POA area. After recovery, animals were locally pretreated with 1) GABA (l-40ng), 2) picrotoxin (1 .5^g) or bicuculhne (0.03ng), or 3) sahne; before injection with carbachol (1 .5^g). The resulting vocalization was measured and quantitated. The results indicate that pretreatment with GABA or GABA antagonists had no significant effect on vocalization. Local pretreatment with GABA did not potentiate the vocal response as measured by its duration, latraicy, and total number of calls. Similarly, pretreatment with picrotoxin or bicuculline had no effects on the same measures of vocalization. The results suggest tfiat chohnoceptive neurons involved in the production of alarm calls are not under direct GABAergic control.

Surface effect ferromagnetism in pure and reduced strontium titanate

A room temperature ferromagnetic hysteresis is observed in single crystal strontium titanate substrates as purchased from several manufacturers. It was found that polishing all sides of the substrates removed this observed hysteresis, suggesting that the origin of the ferromagnetic behavior resides on the surface of the substrates. X-ray diffraction and energy dispersive x-ray spectra were measured however they were unable to detect any impurity phases. In similar semiconducting oxides it was previously suggested that ferromagnetism could originate in oxygen vacancies or from disorder within the single crystal. To this end substrates were annealed in both air and vacuum in a range of temperatures (600°C to 1100°G) to both create bulk oxygen vacancies and to heal surface damage. Annealing in vacuum was found to create a measureable number of oxygen vacancies however their creation could not be correlated to the ferromagnetic signal of the substrate. Annealing in air was found to effect the remnant moment of the substrate as well as the width of the x-ray diffraction peaks on the unpolished face, weakly suggesting a relation between surface based disorder and ferromagnetism. Argon ion bombardment was employed to create a layer of surface disorder in the polished crystal, however it was not found to induce ferromagnetism. It was found that acid etching was sufficient to remove the ferromagnetism from as purchased samples and similarly simulated handling with stainless steel tweezers was sufficient to re-create the ferromagnetism. It is suggested that the origin of this ferromagnetism in SrTi03 is surface contaminants (mainly iron).

Influence d’un rince-bouche fluoré sur la corrosion galvanique entre un fil NiTi ou un fil CuNiTi et différents boîtiers orthodontiques : incidence sur les propriétés mécaniques des fils

Objectif : il a été rapporté que l’utilisation d’agents prophylactiques fluorés pouvait favoriser la corrosion galvanique au sein des alliages de titane. L’objectif de la présente étude était d’évaluer l’effet d’un rince-bouche fluoré sur les propriétés mécaniques de fils en nickel-titane (NiTi) et de fils en cuivre-nickel-titane (CuNiTi) lorsque ces derniers sont couplés à des boîtiers de compositions différentes (boîtiers de marques Smartclip, Clarity, et Sprint). Matériels et Méthodes : 90 segments de fils en NiTi et 90 segments de fils en CuNiTi ont été chacun couplés à 2 boîtiers de chaque marque. Chaque assemblage fil-boîtiers a été par la suite incubé pendant 3 heures à 37°C, soit dans une solution de fluore neutre (Fluorinse™ 0,05% NaF), soit dans une solution de salive artificielle (solution contrôle). Suite à l’incubation, les échantillons étaient nettoyés avec de l’eau déshydrogénée, les fils séparés des boîtiers et montés sur un support pour subir un test de pliage en trois points en milieu humide (salive artificielle) à 37°C. Les modules d’élasticité ainsi que les limites conventionnelles d’élasticité en activation et en désactivation ont été mesurés et comparés. Des analyses de Variance (ANOVA) et des comparaisons post-hoc avec la correction de Bonferronni ont été utilisées pour comparer les groupes entre eux (α = 0,05). Résultats : L’utilisation d’un rince-bouche fluoré a produit une réduction du module d’élasticité et de la limite conventionnelle d’élasticité en activation et en désactivation pour les fils en NiTi ; cependant, cet effet a été modulé par le type de boîtier auquel le fil a été couplé. Les propriétés mécaniques de fils en CuNiTi n’ont pas été affectées par le fluor, ou par le type de boîtier utilisé. Conclusions : L’utilisation d’un rince-bouche fluoré modifie les propriétés mécaniques des fils en NiTi seulement. Cet effet est modulé par le boîtier auquel le fil en NiTi est couplé. A la différence des autres études publiées dans la littérature, nos résultats ne nous permettent pas de conclure que la modification des propriétés mécaniques des fils en NiTi entrainerait obligatoirement un allongement de la durée du traitement orthodontique. Mots clés : Fluor, fils nickel-titane, boîtiers orthodontiques, corrosion galvanique, propriétés mécaniques.

Étude de l'influence de la réassociation en surface des atomes N et O sur l'inactivation des spores bactériennes dans une post-décharge N2-O2 basse pression en flux

Le recours au plasma pour stériliser des dispositifs médicaux (DM) est un domaine de recherche ne datant véritablement que de la fin des années 1990. Les plasmas permettent, dans les conditions adéquates, de réaliser la stérilisation à basse température (≤ 65°C), tel qu’exigé par la présence de polymères dans les DM et ce contrairement aux procédés par chaleur, et aussi de façon non toxique, contrairement aux procédés chimiques comme, par exemple, l’oxyde d’éthylène (OEt). Les laboratoires du Groupe de physique des plasmas à l’Université de Montréal travaillent à l’élaboration d’un stérilisateur consistant plus particulièrement à employer les effluents d’une décharge N2-%O2 basse pression (2-8 Torrs) en flux, formant ce que l’on appelle une post-décharge en flux. Ce sont les atomes N et O de cette décharge qui viendront, dans les conditions appropriées, entrer en collisions dans la chambre de stérilisation pour y créer des molécules excitées NO*, engendrant ainsi l’émission d’une quantité appréciable de photons UV. Ceux-ci constituent, dans le cas présent, l’agent biocide qui va s’attaquer directement au bagage génétique du micro-organisme (bactéries, virus) que l’on souhaite inactiver. L’utilisation d’une lointaine post-décharge évite du même coup la présence des agents érosifs de la décharge, comme les ions et les métastables. L’un des problèmes de cette méthode de stérilisation est la réduction du nombre de molécules NO* créées par suite de la perte des atomes N et O, qui sont des radicaux connus pour interagir avec les surfaces, sur les parois des matériaux des DM que l’on souhaite stériliser. L’objectif principal de notre travail est de déterminer l’influence d’une telle perte en surface, dite aussi réassociation en surface, par l’introduction de matériaux comme le Téflon, l’acier inoxydable, l’aluminium et le cuivre sur le taux d’inactivation des spores bactériennes. Nous nous attendons à ce que la réassociation en surface de ces atomes occasionne ainsi une diminution de l’intensité UV et subséquemment, une réduction du taux d’inactivation. Par spectroscopie optique d’émission (SOE), nous avons déterminé les concentrations perdues de N et de O par la présence des matériaux dans le stérilisateur, ainsi que la diminution de l’émission UV en découlant. Nous avons observé que cette diminution des concentrations atomiques est d’autant plus importante que les surfaces sont catalytiques. Au cours de l’étude du phénomène de pertes sur les parois pour un mélange N2-%O2 nous avons constaté l’existence d’une compétition en surface entre les atomes N et O, dans laquelle les atomes d’oxygènes semblent dominer largement. Cela implique qu’au-delà d’un certain %O2 ajouté à la décharge N2, seuls les atomes O se réassocient en surface. Par ailleurs, l’analyse des courbes de survie bi-phasiques des micro-organismes a permis d’établir une étroite corrélation, par lien de cause à effet, entre la consommation des atomes N et O en surface et la diminution du taux d’inactivation des spores dans la première phase. En revanche, nous avons constaté que notre principal agent biocide (le rayonnement ultraviolet) est moins efficace dans la deuxième phase et, par conséquent, il n’a pas été possible d’établir un lien entre la diminution des concentrations et le taux d’inactivation de cette phase-là.

Growth and Characterization of LiCoO₂ Thin Films for Microbatteries

LiCoO₂thin films have been grown by pulsed laser deposition on stainless steel and SiO₂/Si substrates. The film deposited at 600°C in an oxygen partial pressure of 100mTorr shows an excellent crystallinity, stoichiometry and no impurity phase present. Microstructure and surface morphology of thin films were examined using a scanning electron microscope. The electrochemical properties of the thin films were studied with cyclic voltammetry and galvanostatic charge-discharge techniques in the potential range 3.0-4.2 V. The initial discharge capacity of the LiCoO2 thin films deposited on the stainless steel and SiO₂/Si substrates reached 23 and 27 µAh/cm², respectively.

Protección miocárdica con custodiol y trastornos de la osmolalidad

En análisis retrospectivo evaluamos 91 pacientes llevados a cirugía cardiaca entre 2013 y 2014 en la Fundación Cardioinfantil, en quienes se administro Custodiol, analizando los niveles de sodio y osmolalidad plasmática efectiva antes, durante y después del procedimiento quirúrgico. Nosotros evaluamos la relación entre administración de Custodiol y cambios en el sodio y osmolalidad plasmática del paciente llevado a cirugía cardiaca.

Sustain Cycle

En la búsqueda de preservar el medio ambiente y estandarizar la disposición final de los residuos generados, Sustain Cycle nace como un gestor de residuos de aceite vegetal usado, reforzando la carente oferta del mercado. Fortaleciendo el compromiso de los generadores de este residuo además de una reducción de costos, la creación de Sustain Cycle se desarrolla bajo la figura jurídica de Fundación, deduciendo en los contribuyentes del impuesto el valor de las donaciones efectuadas. El aporte ambiental se basa en minimizar el riesgo de una mala disposición en la red de alcantarillado y su componente social se enfoca en evitar la reutilización ilegal y perjudicial para el consumidor. Sustain Cycle se centra en la recolección, acopio, filtrado y comercialización del AVU generado por todos los establecimientos comerciales que produzcan alimentos como papas a la francesa, empanadas, buñuelos, churros, plátanos y demás productos que requieran del aceite para su cocción.

Pressure-dependent product distribution of citral hydrogenation over micelle-hosted Pd and Ru nanoparticles in supercritical carbon dioxide

In situ synthesis and testing of Ru and Pd nanoparticles as catalysts in the presence of ammonium perfluorohydrocarbo-carboxylate surfactant in supercritical carbon dioxide were carried out in a stainless steel batch reactor at 40 degrees C over a pressure range of 80-150 bar CO2/H-2. Direct Visualization of the formation of a supercritical phase at above 80 bar, followed by the formation of homogeneous microemulsions containing dispersed Ru nanoparticles and Pd nanoparticles in scCO(2) at above 95-100 bar, were conducted through a sapphire window reactor using a W-0 (molar water to surfactant ratio) of 30. The synthesised RU and Pd nanoparticles showed interesting product distributions in the selective hydrogenation of organic molecules, depending critically oil the density and polarity of the fluid (which ill turn depends on the pressure applied). Thus, selective hydrogenation of the citral molecule, which contains three reducible groups (aldehydes and double bonds at the 23 and 6,7 positions), is feasible Lis a chemical probe. (c) 2005 Elsevier Inc. All rights reserved.

Micelle-hosted palladium nanoparticles catalyze citral molecule hydrogenation in supercritical carbon dioxide

A new approach of employing metal particles in micelles for the hydrogenation of organic molecules in the presence of fluorinated surfactant and water in supercritical carbon dioxide has very recently been introduced. This is allegedly to deliver many advantages for carrying out catalysis including the use of supercritical carbon dioxide (scCO(2)) as a greener solvent. Following this preliminary account, the present work aims to provide direct visual evidence on the formation of metal microemulsions and to investigate whether metal located in the soft micellar assemblies could affect reaction selectivity. Synthesis of Pd nanoparticles in perfluorohydrocarboxylate anionic micelles in scCO(2) is therefore carried out in a stainless steel batch reactor at 40 degreesC and in a 150 bar CO2/H-2 mixture. Homogeneous dispersion of the microemulsion containing Pd nanoparticles in scCO(2) is observed through a sapphire window reactor at W-0 ratios (molar water-to-surfactant ratios) ranging from 2 to 30. It is also evidenced that the use of micelle assemblies as new metal catalyst nanocarriers could indeed exert a great influence on product selectivity. The hydrogenation of a citral molecule that contains three reducible groups (aldehyde, double bonds at the 2,3-position and the 6,7-position) is studied. An unusually high selectivity toward citronellal (a high regioselectivity toward the reduction of the 2,3-unsaturation) is observed in supercritical carbon dioxide. On the other hand, when the catalysis is carried out in the conventional liquid or vapor phase over the same reaction time, total hydrogenation of the two double bonds is achieved. It is thought that the high kinetic reluctance for double bond hydrogenation of the citral molecule at the hydrophobic end (the 6,7-position) is due to the unique micelle environment that is in close proximity to the metal surface in supercritical carbon dioxide that guides a head-on attack of the molecule toward the core metal particle.