Development of a technique to measure the residual strength of woodworm infested timber

This paper presents a study of the residual strength of Pinus sylvestris, which has been subject to attack by the furniture beetle (Anobium punctatum). It is relatively easy to stop the infestation, but difficult to assess the structural soundness of the remaining timber. Removal and replacement of affected structural elements is usually difficult and expensive, particularly in buildings of historic interest. Current on-site assessment procedures are limited. The main object of the study was to develop an on-site test of timber quality: a test which can be carried out on the surface and also at varying depths into the timber. It is based on a probe pull-out technique using a portable load-measuring device. Pull-out force values have been correlated with both strength and energy absorbed as measured by compression testing on laboratory samples of both sound and infested timber. These two relationships are significant and could be used to assess whether remedial work is needed. In addition, work on the use of artificial borings to simulate the natural worming of timber is presented and the findings discussed.

Delayed failure of a deep cutting in lodgement till

Recent research on the delayed failure of cuttings in clay clearly recognises and predicts progressive delayed failure of deep cuttings. This is due to a combination of strain-softening, weathering, dissipation of negative excess pore water pressure generated at the time of excavation, and frequent occurrence of prolonged periods of wet weather. There have been several slope failures of this kind in Northern Ireland. This paper discusses a case study based on a failure of a deep cutting, excavated at a slope of 1 in 2, on the A1 near Dromore (County Down) in Northern Ireland. The cutting was in lodgement till, a stiff, heavily overconsolidated clay. The failure occurred approximately 30 years after the cutting was excavated, following a prolonged period of heavy rainfall. An analysis of the failure, together with laboratory test data on soil samples taken from the site, confirmed that by using long-term soil strength parameters the factor of safety of this slope was unity. The conclusion of the analysis is that slopes excavated in this soil should be designed (and assessed) on long-term strength parameters.

Atomic oxygen surface loss coefficient measurements in a capacitive/inductive radio-frequency plasma

Spatially resolved measurements of the atomic oxygen densities close to a sample surface in a dual mode (capacitive/inductive) rf plasma are used to measure the atomic oxygen surface loss coefficient beta on stainless steel and aluminum substrates, silicon and silicon dioxide wafers, and on polypropylene samples. beta is found to be particularly sensitive to the gas pressure for both operating modes. It is concluded that this is due to the effect of changing atom and ion flux to the surface. (C) 2002 American Institute of Physics.

Fabrication of Ti-Al coatings by mechanical alloying method

By means of the mechanical alloying (MA) method, Al and Ti + Al coatings were deposited on Ti alloy substrates. During the mechano-activation processing, the substrate surface was impacted by a large number of flying balls along with particles of powder. The repeated ball collisions with the substrate resulted in the deposition of powder on its surface. MA technique produced Ti + Al coating with a thickness of 200 µm and Al one with a thickness of 50 µm after 2 h milling at room temperature. The as-synthesized coatings showed structures with high apparent density and free of porosity. The surface morphology of the MA-coatings was very rough. Annealing treatment led to the leveling of this uneven morphology. Annealing at temperatures ranging between 600 °C and 1100 °C gave different aluminide phases on the samples. In the case of Al coating, Al3Ti and Ti3Al compound were observed upon heating up to 1100 °C. In the case of Ti + Al coating, Al3Ti, Al2Ti, TiAl and Ti3Al were formed on the surface.

A Longitudinal and Contextual Analysis of Media Representation of Business Ethics

Purpose – The purpose of this paper is to present an analysis of media representation of business ethics within 62 international newspapers to explore the longitudinal and contextual evolution of business ethics and associated terminology. Levels of coverage and contextual analysis of the content of the articles are used as surrogate measures of the penetration of business ethics concepts into society. Design/methodology/approach – This paper uses a text mining application based on two samples of data: analysis of 62 national newspapers in 21 countries from 1990 to 2008; analysis of the content of two samples of articles containing the term business ethics (comprised of 100 newspaper articles spread over an 18-year period from a sample of US and UK newspapers). Findings – The paper demonstrates increased coverage of sustainability topics within the media over the last 18 years associated with events such as the Rio Summit. Whilst some peaks are associated with business ethics scandals, the overall coverage remains steady. There is little apparent use in the media of concepts such as corporate citizenship. The academic community and company ethical codes appear to adopt a wider definition of business ethics more akin to that associated with sustainability, in comparison with the focus taken by the media, especially in the USA. Coverage demonstrates clear regional bias and contextual analysis of the articles in the UK and USA also shows interesting parallels and divergences in the media representation of business ethics. Originality/value – A promising avenue to explore how the evolution of sustainability issues including business ethics can be tracked within a societal context.

An experiment for two-color photoionization using high intensity extreme-UNT free electron and near-IR laser pulses

We describe an experimental system designed for single-shot photoelectron spectroscopy on free atoms and molecules at the Free Electron Laser in Hamburg (FLASH at DESY). The combination of the extreme ultra-violet (EUV) Free Electron Laser and a temporally synchronized optical fs laser (Ti:Sapphire) enables a variety of two-color pump-probe experiments. The spectral, temporal and spatial characteristics of both the EUV FEL and the optical laser pulses, the experimental procedure to control their overlap as well as the performance of an electron spectrometer used to obtain single-shot photoelectron spectra are discussed. As an illustration of the capabilities of this set-up, some results on two-photon two-color ionization of rare gases are presented. (c) 2007 Elsevier B.V. All rights reserved.

A new method of measuring plastic limit of fine materials

Index properties such as the liquid limit and plastic limit are widely used to evaluate certain geotechnical parameters of fine-grained soils. Measurement of the liquid limit is a mechanical process, and the possibility of errors occurring during measurement is not significant. However, this is not the case for plastic limit testing, despite the fact that the current method of measurement is embraced by many standards around the world. The method in question relies on a fairly crude procedure known widely as the ‘thread rolling' test, though it has been the subject of much criticism in recent years. It is essential that a new, more reliable method of measuring the plastic limit is developed using a mechanical process that is both consistent and easily reproducible. The work reported in this paper concerns the development of a new device to measure the plastic limit, based on the existing falling cone apparatus. The force required for the test is equivalent to the application of a 54 N fast-static load acting on the existing cone used in liquid limit measurements. The test is complete when the relevant water content of the soil specimen allows the cone to achieve a penetration of 20 mm. The new technique was used to measure the plastic limit of 16 different clays from around the world. The plastic limit measured using the new method identified reasonably well the water content at which the soil phase changes from the plastic to the semi-solid state. Further evaluation was undertaken by conducting plastic limit tests using the new method on selected samples and comparing the results with values reported by local site investigation laboratories. Again, reasonable agreement was found.

An assessment of the earth pressure coefficient in overconsolidated clays

The determination of the earth pressure coefficient K 0 in a natural clay deposit is a problem of considerable significance in geotechnical engineering. While the methods for evaluation of K 0 are reliable for normally consolidated soils, significant difficulties still exist in evaluating K 0 in overconsolidated clays, given that it is influenced by the stress history of the material, together with the age, structure, mineralogical composition and depositional environment. Indeed, some of these factors are responsible for the soil becoming anisotropic. The existing framework for prediction of K 0 in overconsolidated soils does not account for any influences caused by anisotropy. The work reported in this paper evaluates the validity of a revised relationship between K 0oc and OCR (overconsolidation ratio) using data obtained from laboratory investigations. The tests were performed on reconstituted and undisturbed samples of Belfast Upper Boulder Clay, London Clay and Gault Clay. Tests were also performed on reconstituted samples of kaolin. The values of K 0oc were determined using various approaches, including on-sample measurements. The results have confirmed that reliable predictions of K 0oc can be made using the proposed relationship.

A Simple Triaxial System for Evaluating the Performance of Unsaturated Soils Under Repeated Loading

Unsaturated soils constitute a large proportion of the foundation materials supporting infrastructure throughout the world and they are subject to various loading conditions. This paper describes the development of a simple system for testing unsaturated soils under repeated loading. The equipment was comprised of a modified triaxial cell with hydraulic loading system, hall-effect transducers for on-sample strain measurements, and thermocouple psychrometer for suction measurements. A number of undrained monotonic and repeated loading triaxial tests were performed on compacted samples of kaolin clay in order to attest the newly developed system. The results yielded some useful information on the resilient modulus and permanent deformation of a soil when subjected to repeated loading. There is some difference between the failure deviator stress of samples subjected to repeated and monotonic loading, though repeated loading continued to result in a significant permanent deformation. This paper is aimed at demonstrating the key features of the equipment using preliminary data generated as part of the on-going research.

A rapid PCR-based assay for identification of cryptic Myotis spp (Myotis mystacinus, Myotis brandtii and Myotis alcathoe).

The development of a quick PCR-based method to distinguish European cryptic Myotis spp., Myotis mystacinus, Myotis brandtii and Myotis alcathoe is described. Primers were designed around species-specific single nucleotide polymorphisms (SNP’s) in the ND1 mitochondrial gene, and a pair of control primers was designed in the 12S mitochondrial gene. A multiplex of seven primer combinations produces clear species-specific bands using gel electrophoresis. Robustness of the method was tested on 33 M. mystacinus, 16 M. brandtii and 15 M. alcathoe samples from across the European range of these species. The method worked well on faecal samples collected from maternity roosts of M. mystacinus. The test is intended to aid collection of data on these species through a rapid and easy identification method with the ability to use DNA obtained from a range of sources including faecal matter.

Epitaxial strain stabilization of ferroelectric phase in PbZrO3 thin films

PbZrO3/SrRuO3/SrTiO3 (100) epitaxial heterostructures with different thickness of the PbZrO3 (PZO) layer (d(PZO) similar to 5-160 nm) were fabricated by pulsed laser deposition. The ultrathin PZO films (d(PZO) <= 10 nm) were found to possess a rhombohedral structure. On increasing the PZO film thickness, a bulk like orthorhombic phase started forming in the film with d(PZO) similar to 22 nm and became abundant in the thicker films. Nanobeam electron diffraction and room-temperature micro-Raman measurements revealed that the stabilization of the rhombohedral phase of PZO could be attributed to the epitaxial strain accommodated by the heterostructures. Room-temperature polarization vs electric field measurements performed on different samples showed characteristic double hysteresis loops of antiferroelectric materials accompanied by a small remnant polarization for the thick PZO films (dPZO >= 50 nm). The remnant polarization increased by reducing the PZO layer thickness, and a ferroelectric like hysteresis loop was observed for the sample with d(PZO) similar to 22 nm. Local ferroelectric properties measured by piezoresponse force microscopy also exhibited a similar thickness-dependent antiferroelectric-ferroelectric transition. Room-temperature electrical properties observed in the PZO thin films in correlation to their structural characteristics suggested that a ferroelectric rhombohedral phase could be stabilized in thin epitaxial PZO films experiencing large interfacial compressive stress.

Trends in coronary risk factors in the WHO MONICA Project

Background. The World Health Organization (WHO) MONICA Project was established to determine how trends in event rates for coronary heart disease (CHD) and, optionally, stroke were related to trends in classic coronary risk factors. Risk factors were therefore monitored over ten years across 38 populations from 21 countries in four continents (overall period covered: 1979-1996). Methods. A standard protocol was applied across participating centres, in at least two, and usually three, independent surveys conducted on random samples of the study populations, well separated within the 10-year study period. Results. Smoking rates decreased in most male populations (35-64 years) but in females the majority showed increases. Systolic blood pressure showed decreasing trends in the majority of centres in both sexes. Mean levels of cholesterol generally showed downward trends, which, although the changes were small, had large effects on risk. There was a trend of increasing body mass index (BMI) with half the female populations and two-thirds of the male populations showing a significant increase. Conclusions. It is feasible to monitor the classic CHD risk factors in diverse populations through repeated surveys over a decade. In general, the risk factor trends are downwards in most populations but in particular, an increase in smoking in women in many populations and increasing BMI, especially in men, are worrying findings with significant public health implications.

Measurement of permeability using a bench-top centrifuge

The commonly used British Standard constant head triaxial permeability test for testing of fine-grained soils is relatively time consuming. A reduction in the required time for soil permeability testing would provide potential cost savings to the construction industry, particularly in the construction quality assurance of landfill clay liners. The purpose of this paper is to evaluate an alternative approach of measuring permeability of fine-grained soils benefiting from accelerated time scaling for seepage flow when testing specimens in elevated gravity conditions provided by a centrifuge. As part of the investigation, an apparatus was designed and produced to measure water flow through soil samples under conditions of elevated gravitational acceleration using a small desktop laboratory centrifuge. A membrane was used to hydrostatically confine the test sample. A miniature data acquisition system was designed and incorporated in the apparatus to monitor and record changes in head and flow throughout the tests. Under enhanced gravity in the centrifuge, the flow through the sample was under ‘variable head' conditions as opposed to ‘constant head' conditions as in the classic constant head permeability tests conducted at 1 g . A mathematical model was developed for analysis of Darcy's coefficient of permeability under conditions of elevated gravitational acceleration and verified using the results obtained. The test data compare well with the results on analogous samples obtained using the classical British Standard constant head permeability tests.

Periodontal systemic associations: review of the evidence

Aim: To critically appraise recent research into associations between periodontal disease and systemic diseases and conditions specifically respiratory disease, chronic kidney disease, rheumatoid arthritis, cognitive impairment, obesity, metabolic syndrome and cancer.

Methods: A MEDLINE literature search of papers published between 2002 and April 2012 was conducted. Studies that included periodontitis as an exposure were identified. Cross-sectional epidemiological investigations on large samples, prospective studies and systematic reviews formed the basis of the narrative review. A threshold set for the identification of periodontitis was used to identify those studies that contributed to the conclusions of the review.

Results: Many of the investigations were cross-sectional secondary analyses of existing data sets in particular the NHANES studies. There were a small number of systematic reviews and prospective studies. There was substantial variability in the definitions of exposure to periodontitis. A small number of studies met the threshold set for periodontitis and supported associations; however, in some of the chronic diseases there were no such studies. There was strong evidence from randomized controlled trials that interventions, which improve oral hygiene have positive effects on the prevention of nosocomial pneumonias.

Conclusions: There was substantial heterogeneity in the definitions used to identify periodontitis and very few studies met a stringent threshold for periodontitis. Published evidence supports modest associations between periodontitis and some, although not all, of the diseases and conditions reviewed. There is a need to reach a consensus on what constitutes periodontitis for future studies of putative associations with systemic diseases.

The feasibility of using near infrared and Raman spectroscopic techniques to detect fraudulent adulteration of chili powders with Sudan dye

Chili powder is a globally traded commodity which has been found to be adulterated with Sudan dyes from 2003 onwards. In this study, chili powders were adulterated with varying quantities of Sudan I dye (0.1-5%) and spectra were generated using near infrared reflectance spectroscopy (NIRS) and Raman
spectroscopy (on a spectrometer with a sample compartment modified as part of the study). Chemometrics were applied to the spectral data to produce quantitative and qualitative calibration models and prediction statistics. For the quantitative models coefficients of determination (R2) were found to be
0.891-0.994 depending on which spectral data (NIRS/Raman) was processed, the mathematical algorithm used and the data pre-processing applied. The corresponding values for the root mean square error of calibration (RMSEC) and root mean square error of prediction (RMSEP) were found to be 0.208-0.851%
and 0.141-0.831% respectively, once again depending on the spectral data and the chemometric treatment applied to the data. Indications are that the NIR spectroscopy based models are superior to the models produced from Raman spectral data based on a comparison of the values of the chemometric
parameters. The limit of detection (LOD) based on analysis of 20 blank chili powders against each calibration model gave 0.25% and 0.88% for the NIR and Raman data, respectively. In addition, adopting a qualitative approach with the spectral data and applying PCA or PLS-DA, it was possible to discriminate
between adulterated chili powders from non-adulterated chili powders.