Isoelectric focusing of urinary metallothionein.

Isoelectric focusing of human urinary metallothionein at a pH range of 4.8 to 7.0 yielded a single protein band with a pI of 5.57 which co-migrated with authentic purified metallothionein I from human liver. Minimum pretreatment of the urine samples (160 ml) was needed. The preparatory steps included sample concentration with the original protein, enriched from 69 +/- 23 micrograms/ml to 2.0 +/- 1.4 mg/ml (+/- SD; n = 9), followed by heat treatment at 80 degrees C for 5 min (2.4 +/- 1.7 mg protein/ml). After focusing, the gels were stained with silver and the lanes were scanned with a laser scanner. Peak areas were used for quantitation with commercial beta 2-microglobulin as a standard. The urinary metallothionein ranged from 1.0 to 2.6 nmol/mmol creatinine, which is comparable with values reached by radio-immunoassay.

Method development for the simultaneous determination of methylmercury and inorganic mercury in seafood

This paper reports the method development for the simultaneous determination of methylmercury MeHgþ) and inorganic mercury (iHg) species in seafood samples. The study focused on the extraction and quantification of MeHgþ (the most toxic species) by liquid chromatography coupled to on-line UV irradiation and cold vapour atomic fluorescence spectroscopy (LC-UV-CV-AFS), using HCl 4 mol/L as the extractant agent. Accuracy of the method has been verified by analysing three certified reference materials and different spiked samples. The values found for total Hg and MeHgþ for the CRMs did not differ significantly from certified values at a 95% confidence level, and recoveries between 85% and 97% for MeHgþ, based on spikes, were achieved. The detection limits (LODs) obtained were 0.001 mg Hg/kg for total mercury, 0.0003 mg Hg/kg for MeHgþ and 0.0004 mg Hg/kg for iHg. The quantification limits (LOQs) established were 0.003 mg Hg/kg for total mercury, 0.0010 mg Hg/kg for MeHgþ and 0.0012 mg Hg/kg for iHg. Precision for each mercury species was established, being 12% in terms of RSD in all cases. Finally, the developed method was applied to 24 seafood samples from different origins and total mercury contents. The concentrations for Total Hg, MeHg and iHg ranged from 0.07 to 2.33, 0.003-2.23 and 0.006-0.085 mg Hg/kg, respectively. The established analytical method allows to obtain results for mercury speciation in less than 1 one hour including both, sample pretreatment and measuring step.

Randomised, multicentre, phase III, open-label study of alectinib vs crizotinib in treatment-naïve anaplastic lymphoma kinase (ALK)-positive advanced NSCLC (ALEX study).

Background: In ∼5% of advanced NSCLC tumours, ALK tyrosine kinase is constitutively activated after translocation of ALK. ALK+ NSCLC was shown to be highly sensitive to the first approved ALK inhibitor, crizotinib. However, all pts eventually relapse on crizotinib mainly due to secondary ALK mutations/amplification or CNS metastases. Alectinib is a highly selective, potent, oral next-generation ALK inhibitor. Clinical phase II alectinib data in 46 crizotinib-naïve pts with ALK+ NSCLC reported an objective response rate (ORR) of 93.5% and a 1-year progression-free rate of 83% (95% CI: 68-92) (Inoue et al. J Thorac Oncol 2013). CNS activity was seen: of 14 pts with baseline brain metastasis, 11 had prior CNS radiation, 9 of these experienced CNS and systemic PFS of >12 months; of the 3 pts without prior CNS radiation, 2 were >15 months progression free. Trial design: Randomised, multicentre, phase III, open-label study in pts with treatment-naïve ALK+ advanced, recurrent, or metastatic NSCLC. All pts must provide pretreatment tumour tissue to confirm ALK rearrangement (by IHC). Pts (∼286 from ∼180 centres, ∼30 countries worldwide) will be randomised to alectinib (600mg oral bid, with food) or crizotinib (250mg oral bid, with/without food) until disease progression (PD), unacceptable toxicity, withdrawal of consent, or death. Stratification factors are: ECOG PS (0/1 vs 2), race (Asian vs non-Asian), baseline CNS metastases (yes vs no). Primary endpoint: PFS by investigators (RECIST v1.1). Secondary endpoints: PFS by Independent Review Committee (IRC); ORR; duration of response; OS; safety; pharmacokinetics; quality of life. Additionally, time to CNS progression will be evaluated (MRI) for the first time in a prospective randomised NSCLC trial as a secondary endpoint. Pts with isolated asymptomatic CNS progression will be allowed to continue treatment beyond documented progression until systemic PD and/or symptomatic CNS progression, according to investigator opinion. Time to CNS progression will be retrospectively assessed by the IRC using two separate criteria, RECIST and RANO. Further details: ClinicalTrials.gov (NCT02075840). Disclosure: T.S.K. Mok: Advisory boards: AZ, Roche, Eli Lilly, Merck Serono, Eisai, BMS, AVEO, Pfizer, Taiho, Boehringer Ingelheim, Novartis, GSK Biologicals, Clovis Oncology, Amgen, Janssen, BioMarin; board of directors: IASLC; corporate sponsored research: AZ; M. Perol: Advisory boards: Roche; S.I. Ou: Consulting: Pfizer, Chugai, Genentech Speaker Bureau: Pfizer, Genentech, Boehringer Ingelheim; I. Bara: Employee: F. Hoffmann-La Roche Ltd; V. Henschel: Employee and stock: F. Hoffmann-La Roche Ltd.; D.R. Camidge: Honoraria: Roche/Genentech. All other authors have declared no conflicts of interest.

Vestibular Schwannoma: The Evolution of Hearing and Tumor Size in Natural Course and after Treatment by LINAC Stereotactic Radiosurgery.

OBJECTIVE: To review the natural course of tumor size and hearing during conservative management of 151 patients with unilateral vestibular schwannoma (VS), and to evaluate the same parameters for the part of the group (n = 84) who were treated by LINAC stereotactic radiosurgery (SRS). METHODS: In prospectively collected data, patients underwent MRI and complete audiovestibular tests at inclusion, during the conservative management period and after SRS. Hearing was graded according to the Gardner-Robertson (GR) scale and tumor size according to Koos. Statistics were performed using Kaplan-Meier survival analysis and multivariate analyses including linear and logistic regression. Specific insight was given to patients with serviceable hearing. RESULTS: During the conservative management period (mean follow-up time: 24 months, range: 6-96), the annual risk of GR class degradation was 6% for GRI and 15% for GR II patients. Hearing loss as an initial symptom was highly predictive of further hearing loss (p = 0.003). Tumor growth reached 25%. For SRS patients, functional hearing preservation was 51% at 1 year and 36% at 3 years. Tumor control was 94 and 91%, respectively. CONCLUSION: In VS patients, hearing loss at the time of diagnosis is a predictor of poorer hearing outcome. LINAC SRS is efficient for tumor control. Patients who preserved their pretreatment hearing presented less hearing loss per year after SRS than before treatment, suggesting a protective effect of SRS when cochlear function can be preserved.

Extrafascial injection for interscalene brachial plexus block reduces respiratory complications compared with a conventional intrafascial injection: a randomized, controlled, double-blind trial?.

BACKGROUND: Hemidiaphragmatic paresis after ultrasound-guided interscalene brachial plexus block is reported to occur in up to 100% of patients. We tested the hypothesis that an injection lateral to the brachial plexus sheath reduces the incidence of hemidiaphragmatic paresis compared with a conventional intrafascial injection, while providing similar analgesia. METHODS: Forty ASA I-III patients undergoing elective shoulder and clavicle surgery under general anaesthesia were randomized to receive an ultrasound-guided interscalene brachial plexus block for analgesia, using 20 ml bupivacaine 0.5% with epinephrine 1:200 000 injected either between C5 and C6 within the interscalene groove (conventional intrafascial injection), or 4 mm lateral to the brachial plexus sheath (extrafascial injection). The primary outcome was incidence of hemidiaphragmatic paresis (diaphragmatic excursion reduction >75%), measured by M-mode ultrasonography, before and 30 min after the procedure. Secondary outcomes were forced vital capacity, forced expiratory volume in 1 s, and peak expiratory flow. Additional outcomes included time to first opioid request and pain scores at 24 h postoperatively (numeric rating scale, 0-10). RESULTS: The incidences of hemidiaphragmatic paresis were 90% (95% CI: 68-99%) and 21% (95% CI: 6-46%) in the conventional and extrafascial injection groups, respectively (P<0.0001). Other respiratory outcomes were significantly better preserved in the extrafascial injection group. The mean time to first opioid request was similar between groups (conventional: 802 min [95% CI: 620-984 min]; extrafascial: 973 min [95% CI: 791-1155 min]; P=0.19) as were pain scores at 24 h postoperatively (conventional: 1.6 [95% CI: 0.9-2.2]; extrafascial: 1.6 [95% CI: 0.8-2.4]; P=0.97). CONCLUSIONS: Ultrasound-guided interscalene brachial plexus block with an extrafascial injection reduces the incidence of hemidiaphragmatic paresis and impact on respiratory function while providing similar analgesia, when compared with a conventional injection. CLINICAL TRIAL REGISTRATION: NCT02074397.

Barrier-protective effects of activated protein C in human alveolar epithelial cells

Acute lung injury (ALI) is a clinical manifestation of respiratory failure, caused by lung inflammation and the disruption of the alveolar-capillary barrier. Preservation of the physical integrity of the alveolar epithelial monolayer is of critical importance to prevent alveolar edema. Barrier integrity depends largely on the balance between physical forces on cell-cell and cell-matrix contacts, and this balance might be affected by alterations in the coagulation cascade in patients with ALI. We aimed to study the effects of activated protein C (APC) on mechanical tension and barrier integrity in human alveolar epithelial cells (A549) exposed to thrombin. Cells were pretreated for 3 h with APC (50 mg/ml) or vehicle (control). Subsequently, thrombin (50 nM) or medium was added to the cell culture. APC significantly reduced thrombin-induced cell monolayer permeability, cell stiffening, and cell contraction, measured by electrical impedance, optical magnetic twisting cytometry, and traction microscopy, respectively, suggesting a barrier-protective response. The dynamics of the barrier integrity was also assessed by western blotting and immunofluorescence analysis of the tight junction ZO-1. Thrombin resulted in more elongated ZO-1 aggregates at cell-cell interface areas and induced an increase in ZO-1 membrane protein content. APC attenuated the length of these ZO-1 aggregates and reduced the ZO-1 membrane protein levels induced by thrombin. In conclusion, pretreatment with APC reduced the disruption of barrier integrity induced by thrombin, thus contributing to alveolar epithelial barrier protection.

A combustão catalítica do metano: estudo estatístico do efeito das variáveis de preparação e pré-tratamento de catalisadores de paládio suportado sobre a atividade catalítica

The catalytic combustion of methane on alumina supported palladium catalysts was studied. It has been reported that the activity of the catalyst increases with its time on line, despite of an increase of the palladium particle size. However, different preparation, pretreatment and testing conditions can be the reason for the observed different results. An experimental design, which allows to verify the influence of several parameters at the same time with a good statistical quality, was used. A Plackett-Burman design was selected for the screening of the variables which have an effect on the increase of the catalyst activity.

Paperin puhtauden parantaminen lajittelun ja muiden prosessiteknisten keinojen avulla

Tämä työ suoritettiin UPM- Kymmene Oyj:n Tervasaaren tehtaan PK 5:llä. PK 5 valmistaa tarrantaustapaperia. Tämän työn tarkoituksena oli löytää eri keinoja paperin puhtauden parantamiseksi. Puhtaamman paperin valmistaminen parantaa paperikoneen kilpailukykyä kilpailijoihinsa nähden sekä vähentää asiakasvalituskustannuksia. Työn kirjallinen osa koostuu kolmesta suuremmasta kokonaisuudesta, joiden tarkoituksena on luoda teoriapohjaa kokeellisen osan suoritusta varten. Kirjallisuusosan pääpaino on kohdistettu PK 5:llä esiintyviin saostumanaiheuttajiin, kuten uuteaineisiin, ASA- liimaan ja mikrobeihin. Tarkemmassa tarkastelussa on kirjallisuusosassa myös painelajittelu ja pyörrepuhdistus. Kokeellisessa osassa suoritettiin PK 5:n prosessissa syntyvien epäpuhtauksien karakterisointi. Suurimmat saostuman aiheuttajat analyysien perusteella olivat puuperäiset uuteaineet ja ASA- liima. Epäorgaanisista aineista päällystyskomponenttina toimiva kaoliini ja sellun mukana tuleva pihkatalkki esiintyi useimpien saostumien komponentteina. Selvityksessä havaittiin, että prosessille vieraita aineita ei löydetty muista, kuin kalanteroidusta paperista analysoiduista tummista täplistä. Tummista täplistä analysoitu styreenin alkuperä voi selittyä mm. prosessiin päässeellä kumilla tai muovilla. PK 5:n prosessissa selvityksen mukaan silikonipohjainen vaahdonestoaine aiheuttaa erittäin suuria tummia saostumia, joten sen pääsy prosessiin tulee estää sellutehtaalla tarkoin. Epäpuhtauksien määrä on suurin PK 5:n prosessissa hylkylinjassa ja lyhyessä kierrossa. Hylyn painelajittelu poistaa hyvin roskia syöttömassasta. Hylyn lajittelun toisen portaan lajittimen rejektin roskapitoisuus on suhteellisen suuri. Rejektin ohjaaminen ulos prosessista vähentää roskaisuuden rikastumista prosessiin. Sakeamassalajittelun sijoittaminen PK 5:n konekyypin jälkeen vähentää roskien päätymistä paperiin. Hylyn painelajittelun ja PP- laitoksen rejektin ohjaaminen sakeamassalajittelun toiseen portaaseen vähentäisi priimakuitutappiota ja roskien määrää käytetyissä massoissa. Seisokin aikaisen putkilinjojen pesujen lopputulos parani huomattavasti BA- pesuaineen käyttöönoton jälkeen. Kyseisen pesuaine soveltuu liuottamaan putkistosta mm. PK 5:llä esiintyvät uuteaine- ja ASA- saostumat. BSA- sellun pH- säädön lopettamisella oli suuri vähentävä vaikutus tummien täplien esiintymistiheyteen. pH- säädössä BSA- tornin pohjalaimennukseen annosteltu lipeä edesauttoi tummien saostumien syntymistä saippuoiden uuteaineita.

The chemistry involved in the steam treatment of lignocellulosic materials

Pretreatment of lignocellulosic materials is essential for bioconversion because of the various physical and chemical barriers that greatly inhibit their susceptibility to bioprocesses such as hydrolysis and fermentation. The aim of this article is to review some of the most important pretreatment methods developed to date to enhance the conversion of lignocellulosics. Steam explosion, which precludes the treatment of biomass with high-pressure steam under optimal conditions, is presented as the pretreatment method of choice and its mode of action on lignocellulosics is discussed. The optimal pretreatment conditions for a given plant biomass are defined as those in which the best substrate for hydrolysis is obtained with the least amount of soluble sugars lost to side reactions such as dehydration. Therefore, pretreatment optimization results from a compromise between two opposite trends because hemicellulose recovery in acid hydrolysates can only be maximized at lower pretreatment severities, whereas the development of substrate accessibility requires more drastic pretreatment conditions in which sugar losses are inevitable. To account for this heterogeneity, the importance of several process-oriented parameters is discussed in detail, such as the pretreatment temperature, residence time into the steam reactor, use of an acid catalyst, susceptibility of the pretreated biomass to bioconversion, and process design.

O uso de radiação ultravioleta para o pré-tratamento de amostras em análise inorgânica

The basic principles of UV irradiation as sample pre-treatment step and its potential for inorganic analysis are illustrated and discussed through significant examples from the literature. Not only does this overview cover the classical applications of this technique in the decomposition of organic matter in electroanalysis, but it also presents recent trends, including the increasing interest in employing UV irradiation in flow analytical systems, successful attempts to enhance its effectiveness and the coupling with chromatographic and spectroscopic methodologies. Furthermore, a number of relevant cases of UV-driven derivatization reactions involving photo-sensitive inorganic species are presented, showing some convenient options to perform fast and reliable determination of inorganic and organic analytes.

Fouling management and retention in nanofiltration of integrated paper mill effluents

Nanofiltration performance was studied with effluents from the pulp and paper industry and with model substances. The effect of filtration conditions and membrane properties on nanofiltration flux, retention, and fouling was investigated. Generally, the aim was to determine the parameters that influence nanofiltration efficiency and study how to carry out nanofiltration without fouling by controlling these parameters. The retentions of the nanofiltration membranes studied were considerably higher than those of tight ultrafiltration membranes, and the permeate fluxes obtained were approximately the same as those of tight ultrafiltration membranes. Generally, about 80% retentions of total carbon and conductivity were obtained during the nanofiltration experiments. Depending on the membrane and the filtration conditions, the retentions of monovalent ions (chloride) were between 80 and 95% in the nanofiltrations. An increase in pH improved retentions considerably and also the flux to some degree. An increase in pressure improved retention, whereas an increase in temperature decreased retention if the membrane retained the solute by the solution diffusion mechanism. In this study, more open membranes fouled more than tighter membranes due to higher concentration polarization and plugging of the membrane material. More irreversible fouling was measured for hydrophobic membranes. Electrostatic repulsion between the membrane and the components in the solution reduced fouling but did not completely prevent it with the hydrophobic membranes. Nanofiltration could be carried out without fouling, at least with the laboratory scale apparatus used here when the flux was below the critical flux. Model substances had a strong form of the critical flux, but the effluents had only a weak form of the critical flux. With the effluents, some fouling always occurred immediately when the filtration was started. However, if the flux was below the critical flux, further fouling was not observed. The flow velocity and pH were probably the most important parameters, along with the membrane properties, that influenced the critical flux. Precleaning of the membranes had only a small effect on the critical flux and retentions, but it improved the permeability of the membranes significantly.

Catalisador Pd/gama-Al2O3: efeito do tamanho de partícula na atividade catalítica para combustão do CH4

Methane, the main constituent of natural gas (> 85%), is employed in large scale as an energy source (thermoelectric power plants, automobiles, etc). However, significant quantities of this gas contribute to the greenhouse effect. The catalytic combustion of methane can minimize these emissions. Palladium is one of the metals that shows the highest activity, depending on the different active forms of the metal. In this article, we focus on the influence of particle size and pretreatment on the catalytic performance of palladium in the methane combustion reaction.

The effect of lignin as a natural adhesive on the physico-mechanical properties of Vitis vinifera fiberboards

Lignin was used as a natural adhesive to manufacture Vitis vinifera fiberboards. The fiberboards were produced at laboratory scale by adding powdered lignin to material that had previously been steam-exploded under optimized pretreatment and pressing conditions. The kraft lignin used was washed several times with an acidic solution to eliminate any contaminants and low molecular weight compounds. This research studied the effects of amounts of lignin ranging from 5% to 20% on the properties of Vitis vinifera fiberboards. The fiberboard properties evaluated were density, water resistance in terms of thickness swelling, water absorption, and the mechanical properties in terms of modulus of rupture, modulus of elasticity, and internal bond. Results showed that fiberboards made from Vitis vinifera without lignin addition had weaker mechanical properties. However, the fiberboards obtained using acid-washed kraft lignin as a natural adhesive had good mechanical and water resistance properties that fully satisfied the relevant standard specifications

Uso de frascos de polipropileno descartáveis no pré-tratamento de amostras de água para determinação de chumbo, cobre e mercúrio por voltametria de onda quadrada

In this work a simple and versatile procedure is described for treating water samples using small polypropylene (PP) vials (4 mL) for determining heavy metals by square wave voltammetry (SWV). This procedure involves treatment with nitric acid (0.2 mol L-1) and boiling in a water-bath (~ 100 ºC). This process is completed after one hour and allows the pretreatment of several samples simultaneously. The accuracy was estimated using addition/recovery studies and certified water sample analysis, yielding an agreement near to 100%.