Obtenção de placas cerâmico a partir de formulações de massas triaxiais de resíduos de caulim, chamote de telha e cinza vegetal

The production of red ceramic is an industrial activity that causes an intense impact. The manufacture of its products considerably increases the demand for natural resources, mainly with the extraction of raw material. The ceramic material produced generates waste, such as ash firewood and chamote. The residue from the beneficiation of kaolin is deposited in a poor, degrades the environment and contaminate water sources and soil, constituting in this manner, ecological disasters. The main objective of this work is to develop the formulation of a ceramic product consisting solely of industrial solid wastes, from ceramic tiles, (chamote) residue of kaolin and ash firewood. It is assumed that this product made in the laboratory can be used in coatings, wall and floor. The aim is to facilitate the replacement of the raw material of original composition of a ceramic body, for waste, while the process of production equal to the conventionally used, so that the properties of the product are reproduced. This work is characterized waste as its chemical composition, analysis of particle size, X-ray diffraction and thermal behavior. Several formulations were studied. The mass of waste was prepared by dry process, pressed to 25 MPa, and then burned in muffle type oven to 850, 950, 1050 and 1150 °C. The results showed that it is technically possible to produce porous tiles only with waste. It was found that the formulations of bodies play a key role in the properties of the final product, as well as the sintering temperature and heating rates. RN in the waste of kaolin is estimated at 15,000 t/month, about 3,000 gray t/month and chamote with 10 million pieces/month damaged. The presence of carbonates of calcium and magnesium at 1050 ° C results in an appropriate porosity and mechanical strength. The formulation M3JE, composed of 69% waste of kaolin, 7.7% and 23.3% of chamote of gray, became suitable for porous materials with the strength and absorption within the level of national and international standards

A influência da adição de caulim, quartzo e feldspato potássico na formulação de massas cerâmicas para telhas: Modelo estatístico

The production of roof tiles in the state of Rio Grande do Norte accounts for around 60% of the total of ceramic pieces produced. There is a need for investment to improve quality and productivity, thereby promoting technological innovations. Accordingly, the aim of this study is to determine the effect of kaolin, potassium feldspar and quartz in two standard formulations, as well as the effect of sintering temperature on the technological properties of linear firing shrinkage, water absorption and bending rupture stress, by fitting the statistical model and using multiple linear regression to assess the relationship between technological properties and independent variables. The raw materials were characterized using the following techniques: X-ray fluorescence (XRF), X-ray diffraction (XRF), rational analysis (RA), differential thermal analysis (DTA) and granulometric analysis (GA). The test specimens were compacted by uniaxial pressure (25 MPa), dried in a stove at 110 ºC for 24 hours and sinterized at 850 ºC, 950 ºC and 1050 ºC and held isothermal for 30 minutes. The results obtained indicate that the addition of kaolin to two standard formulations (M and R) promoted a reduction in water absorption values and an increase in bending rupture stress values. The sintering temperatures for group M that resulted in the lowest linear firing shrinkage and water absorption values were 850 ºC and 950 ºC, respectively, and the highest bending rupture stress values were reached at a temperature of 950 ºC. In the case of group R, the sintering temperature that obtained the lowest water absorption and linear firing shrinkage values was 850 ºC, and the highest bending rupture stress values were attained at a temperature of 1050 ºC. This work explains the statistical approach used to fit the model that describes the relationship between the technological properties and percentage of kaolin, quartz and feldspar, as well as the models that enable predictions, provided that the lower and upper limits of the percentage of clay minerals, flux and quartz used in this study are respected. Statistica 6 software was used and results were obtained by stepwise forward regression

Estudo da formulação de massas cerâmicas provenientes da região do Seridó-RN para fabricação de telhas

This work has for objective study compared the characteristics and technological properties of ceramic bodies from the region of Seridó-RN. The region under study has identified 23 cities where they were 80 ceramics industries. To define the universe of search, there was a survey of pottery that are part of APL Seridó next to the IEL. The characteristics and operating conditions of ceramics industries of the region were identified through a socio-economic questionnaire applied locally, which addressed issues such as: profiles of companies, production process etc. The analysis of information collected from 24 companies identified in seven cities shows that the vast majority of industries is small, with family structure, obsolete equipment and labo, little qualified. Most of the pottery works with low technical knowledge, poor control of the production process and product technology. The raw collected were submitted to analysis of X ray diffraction, chemical composition, termical analysis, particle size distribution and plasticity. Then were produced five formulations and made by uniaxial pressure at 25 MPa for firing in temperatures varying from 850 to 1050 °C. The firing technological properties evaluated were: mass loss to fire, lineal shrinkage, apparent density, apparent porosity, water absorption and flexural strength (3 points). The results indicated that the raw materials from the region have significant similarities in the composition chemical and mineralogical. Furthermore, it indicates the possibility of the use of cycles of firing faster and efficient than the current, limited to some clay mass burning of certain conditions

Obtenção de compósitos cerâmicos baseados em Al2O3/TiC através dos precursores poliméricos

The obtaining of ceramic materials from polymeric precursors is subject of numerous studies due to lower energy costs compared to conventional processing. The aim of this study is to investigate and improve the mechanism for obtaining ceramic matrix composite (CMC) based on SiOC/Al2O3/TiC by pyrolysis of polysiloxane in the presence of an active filler and inert filler in the pyrolysis temperature lower than the usually adopted for this technique, with greater strength. It also investigates the influence of pyrolysis temperature, the content of Alas active filler, the presence of infiltrating agents (Al, glass and polymer) after pyrolysis, temperature and infiltration time on some physical and mechanical properties. Alumina is used as inert filler and Al and Ti as active filler in the pyrolysis. Aluminum, glass and polysiloxane are used as agents infiltrating the post-pyrolysis. The results are analyzed with respect to porosity and bulk density by the Archimedes method, the presence of crystalline phases by X-ray diffraction (XRD) and microstructure by scanning electron microscopy (SEM). The ceramic pyrolyzed between 850 °C 1400 °C contain porosity 15% to 33%, density 2.34 g/cm3 and flexural strength at 4 points from 30 to 42 MPa. The microstructure features are porous, with an array of Al2O3 reinforced by TiC particles and AlTi3. The infiltration post-pyrolysis reveals decrease in porosity and increase density and strength. The composites have potential applications where thermal stability is the main requirement

Estudo de formulação de massa para aplicação em placas cerâmicas

The sector of civil construction is strongly related to the red ceramic industry. This sector uses clay as raw material for manufacturing of various products such as ceramic plates. In this study, two types of clay called clay 1 and clay 2 were collected on deposit in Ielmo Marinho city (RN) and then characterized by thermogravimetric analysis (TG/DTG), differential thermal analysis (DTA), X-ray diffraction (XRD), X-ray fluorescence (XRF), rational analysis and particle size distribution and dilatometric analyses. Ceramic plates were manufactured by uniaxial pressing and by extrusion. The plates obtained by pressing were produced from the four formulations called 1, 2, 3 and 4, which presented, respectively, the following proportions by mass: 66.5% clay 1 and 33.5% clay 2, 50% clay 1 and 50% clay 2, 33.5% clay 1 and 66.5% clay 2, 25% clay 1 and 75% clay 2. After firing at 850, 950 and 1050 °C with heating rate of 10 °C/min and soaking time of 30 minutes, the following technological properties were determined: linear firing shrinkage, water absorption, apparent porosity, apparent specific mass and tensile strength (3 points). The formulation containing 25% clay 1 produced plates with most satisfactory results of water absorption and mechanical resistance, because of that it was chosen for manufacturing plates by extrusion. A single firing cycle was established for these plates, which took place as follow: heating rate of 2 °C/min up to 600 ºC with soaking time of 60 minutes, followed by heating using the same rate up to 1050 ºC with soaking time of 30 minutes. After this cycle, the same technological properties investigated in the plates obtained by pressing were determined. The results indicate (according to NRB 13818/1997) that the plates obtained by pressing from the mixture containing 25 wt% clay 1, after firing at 1050 °C, reach the specifications for semi-porous coating (BIIb). On the other hand, the plates obtained by extrusion were classified as semi-stoneware (group AIIa)

Propriedades cerâmicas e imobilização do manganês em cerâmica estrutural

In this work is the addition of a metallic ion, of the metal Manganese, in a clay of Rio Grande do Norte state for structural ceramics use, the objective this study was to assess the evolution of ceramic properties. The clay was characterized by Chemical and Thermal analysis and Xray difraction. The metallic ion was added in the clay as aqueous solutions at concentrations of 100, 150 and 200 mg / L. The molded by extrusion and the burned were temperatures at 850, 950, 1050 and 1150 º C. Was made Chemical Analysis and investigated the following parameters environmental and ceramic: Solubility, Colour, Linear Retraction (%), Water Absorption (%), Gresification Curves, Apparent Porosity (%), Apparent Specific Mass (g/cm3) and Flexion Rupture Module (kgf/cm2). The results showed that increasing the concentration of metallic ion, properties such as Apparent Porosity (%), Water Absorption (%) decreases and the Flexion Rupture Module (kgf/cm2) increases with increasing temperature independent of the concentration of the ion. The gresification curves showed that the optimum firing temperatures were in the range between 950 and 1050 ° C. The evaluation of the properties showed that the ceramic material can be studied its use in solid brick and ceramic materials with structural function of filling. The results of solubility showed that the addition of ion offers no risk to the environment

Electronic structure and optical properties of BaMoO4 powders

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Frequency synthesizer using a hybrid analog/digital loop filter: A low complexity approach

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Properties of DLC films deposited by an oxyacetylene flame

Diamond-like carbon (DLC) films were obtained by spinning a tungsten carbide substrate at a high speed using an oxyacetylene flame. The films deposited at a typical experimental condition of substrate temperature of 810 degrees C, rotation of 600 rpm and 3 h deposition time, exhibited an uniform, very smooth, hard and glassy surface covering the entire exposed face of the substrate. These films were identified as DLC by their characteristic broad Raman spectra centered at 1554 cm(-1) and micro-Vicker's hardness > 3400 kg mm(-2). For substrate temperatures < 800 degrees C the film started losing the uniform glassy surface and the hardness deteriorated. For temperatures > 950 degrees C the film was still hard and shiny, but black in color. DLC films were also obtained in a wide range of speeds of rotation (300-750 rpm), as long as the temperature remained close to 850 degrees C. (C) 1999 Elsevier B.V. S.A. All rights reserved.

Impacto da cárie precoce severa na infância na qualidade de vida relacionada à saúde bucal de pré-escolares sob privação social

Early childhood caries, especially in its severe form, which is characterized by an acute and aggressive nature, can have negative impacts on thequality of life of a child, due to effects such as difficulty in chewing, decreased appetite, weight loss, insomnia, changes in behavior and a decreased performance in school, among others. Moreover, the quality of life of the child`s family can also be affected, as the pain and discomfort caused by this type of caries result in loss of working days of parents, spending on dental treatments, changes in sleep patterns and stress. The aim of this study was to evaluate the impact of severe early childhood caries in the Oral Health-Related Quality of Life (OHRQoL) of public daycares`s preschool children through the Escala de Impacto da Saúde Bucal na Primeira Infância, a Brazilian version of the Early Childhood Oral Health Impact Scale (ECOHIS). A single calibrated examiner (kappa=1.0) evaluated, through the dmfs index, the oral health of 116 children aged between 3 and 5, which were included in one of three study groups: "caries-free", "not-severe early childhood caries" and "severe early childhood caries". The parents responded to ECOHIS, to assess their perception regarding the OHRQoL of their children, and a questionnaire on socioeconomic conditions. The OHRQoL was measured through the total scores and domains of ECOHIS. Descriptive analysis, Mann-Whitney test, Kruskal-Wallis test, chi-square test and Poisson multiple regression with robust variance were used. Among the children observed, 38.8% were caries-free, 27.6% showed not-severe early childhood caries and 33.6% showed severe early childhood caries. Regarding the total score of ECOHIS, severe early childhood caries had a greater negative impact on OHRQoL, compared to caries-free and not-severe early childhood caries groups (p <0.001). Regarding the child subscale, there was significant difference between the "severe early childhood caries" group and the other groups in all domains, except for theone of self-image / social interaction. In the family subscale domains, there was statistical significance between the severe early childhood caries and the caries-free groups in all domains (p <0.001), whereas between the "severe early childhood caries and not-severe early childhood caries groups there was a statistically significant difference only in the domain of parental anguish (p <0.001). Multivariate analysis showed that early childhood caries and the parent`s age were significantly associated to OHRQoL (p <0.05), independently of the other variables in the model. The presence of severe early childhood caries resulted in greater negative impact on OHRQoL (AdjPR= 6.016; 95%CI = 3.12 11.56; p<0.001), while older parents reported better OHRQoL (AdjPR = 0.603; 95%CI = 0.428 - 0.850; p = 0.004). The presence of severe early childhood caries had a negative impact on OHRQoL of preschool children and their families.

Cultivo de algas marinhas como desenvolvimento de comunidades costeiras

In northeastern Brazil, the extraction of agar has increased considerably in recent decades mainly using macroalgae of the genus Gracilaria. The pressure of the harvest of seaweed of this genus has compromised the sustainability of this natural resource. Given the current framework of decline in production of algae in the state of Rio Grande do Norte, it is necessary the deployment of crops that will assist in the development of coastal areas. This research aimed to develop studies on growth, productivity, efficiency and quality of agar of G. birdiae so as to provide subsidies for crops on commercial scale. The study was carried out in dry and rainy periods using rafts of cultivation. Algal biomass and the physical and chemical parameters of water were measured every fifteen days. In laboratory, the resistance and quality of agar were analyzed. The relative growth rate (TCR) was determined by the formula: RGR = ln (final weight / weight initial). 100 / interval time of sampling. During the study, environmental factors as salinity and temperature remained relatively constant (around 35 PSU and 28°C, respectively). The mean values of biomass ranged around 1952.67 ± 576g in the rainy period and 1925.67 ± 450g in the dry period, and they presented no significant variations. The maximum value of growth (TCR) was recorded in the dry season (7.45%.day-1), with an average over the study of 4.35%.day-1. The yield of agar ranged from 22% to 15%, and its resistance ranged from 850 to 650g. cm². The average obtained for the two periods was approximately 750 g cm². These results demonstrate the great potential of Gracilaria birdiae for mariculture can be used as an sustainable activity for coastal communities

Avaliação de uma fração polissacaridica da alga Lobophora variegata (Lamouroux) em modelo de artrite induzida em ratos por Zymosan

Fucans seaweed Lobophora variegata estructures are known for their chemical and biological properties. In this study, we analyzed, the action of fucans L. variegata and the fractions purified with acetone in Zymosan-induced arthritis. After differential fractionation with acetone, six fractions were obtained and named F0.3, F0.5, F0.8, F1, F1.5 and F2. The results showed that the fraction F1 showed high yield (51.9%) and was chosen for studies of antioxidant activity and induced arthritis. Nuclear magnetic resonance (NMR) of 13C showed signals at 103.3 and 15.78 ppm that are assigned to links β13 galactose and of the C6 methyl fucose, respectively. The infrared (IR) showed absorbance at 1238 and 850 cm-1 which are attributed to sulfate. The fraction F1 showed antioxidant activities in vitro. For analysis of inflammatory parameters chosen the polysaccharide was administered in different doses (25, 50 and 75 mg / kg ip, per body weight) and diclofenac sodium (5 mg / kg ip) and L-NAME (25 mg / kg ip) in groups of animals (n = 6). After 6 h, were analyzed for cellular influx and levels of nitrite. In experiment five days, were made analysis of swelling and serum TNF-α. Histopathological analysis were performed for confirmation of results. The fraction F1 (25, 50 and 75 mg / kg ip) reduced the cellular influx (52.1 to 96.7%) and nitric oxide levels (27.2 - 39%) compared to control group. The reduction of edema (63.4 - 100%) and serum TNF-α (p <0.001) were observed when the polysaccharide F1 administered at a dose (50 mg / kg) These results suggest that these heterofucanas of Lobophora variegata have besides the activity antioxidant and potential anti-inflammatory activity in arthritis induced by zymosan

Caracterização geomorfológica e modelagem de dados espaciais na plataforma continental rasa do RN nos limites da folha Touros

This work focuses the geomorphological characterization and spatial data modeling in the shallow continental shelf within the Folha Touros limits (SB-25-CV-II), based on bathymetric data analysis and remote sensing products interpretation. The Rio Grande do Norte state is located in northeastern Brazil and the work area is located at the transition region between the eastern and northern portions of their coast. The bathymetric surveys were conduced between march and may 2009, using a 10 meters long vessel and 0.70 meters draught, equipped with global positioning system and echo sounder (dual beam, 200KHz , 14°). The fieldwork resulted in 44 bathymetric profiles espaced 1.5 km and 30 km average length. The bathymetric data amount were 111,200 points and were navigated 1395.7 km within na area about 1,850 km2. The bathymetric data were corrected for the tide level, vessel draught and were subsequently entered into a geographic information system for further processing. Analysis of remote sensing products was carried out using Landsat 7/ETM + band 1, from november 1999. The image was used for visualization and mapping submerged features. The results showed the presence of geomorphological features within the study area. Were observed, from the analysis of local bathymetry and satellite image, seven types of geomorphological features. The channels, with two longitudinals channels (e. g. San Roque and Cioba channels) and other perpendicular to the coast (e. g. Touros, Pititinga and Barretas). Coastal reef formations (Maracajaú, Rio do Fogo and Cioba). Longitudinal waves, described in the literature as longitudinal dunes. The occurrence of a transverse dune field. Another feature observed was the oceanic reefs, an rock alignment parallel to the coast. Were identified four riscas , from north to south: risca do Liso, Gameleira, Zumbi, Pititinga (the latter being described for the first time). Finally, an oceanic terrace was observed in the deepest area of study. Image interpretation corroborated with the in situ results, enabling visualization and description for all features in the region. The results were analysed in an integrating method (using the diferent methodologies applied in this work) and it was essential to describe all features in the area. This method allowed us to evaluate which methods generated better results to describe certain features. From these results was possible to prove the existence of submerged features in the eastern shallow continental shelf of Rio Grande do Norte. In this way, the conclusions was (1) this study contributed to the provision of new information about the area in question, particularly with regard to data collection in situ depths, (2) the method of data collection and interpretation proves to be effective because, through this, it was possible to visualize and interpret the features present in the study area and (3) the interpretation and discussion of results in an integrated method, using different methodologies, can provide better results

Mel e açúcar mascavo na cicatrização de feridas

O estudo teve como objetivo comparar a eficácia do mel e do açúcar mascavo na cicatrização de feridas induzidas cirurgicamente na pele de cobaias, para avaliar o tempo de cicatrização, as variações macroscópicas e microscópicas do tecido cicatricial, a contração das feridas e o grau de contaminação. Quinze cobaias da raça Abissínia, machos inteiros, de seis meses de idade e pesando entre 500 a 850 gramas, foram divididas em três grupos com cinco animais cada, nos quais foram induzidas, cirurgicamente, três feridas em cada animal com dimensão de 1,5cm² e distância entre elas de 1,5cm, na região dorsal. A ferida F1 foi tratada diariamente com mel, a ferida F2 com solução salina 0,9% (controle) e a ferida F3 com o açúcar mascavo. A eutanásia foi realizada no Grupo 1 ao sétimo dia após a cirurgia, no Grupo 2 ao décimo quarto dia e no Grupo 3 no vigésimo primeiro dia após a cirurgia, sendo as biópsias encaminhadas para avaliação histopatológica. Foram também realizados swabs das feridas em todos os grupos no terceiro e sétimo dias após a cirurgia e as amostras enviadas para a cultura e isolamento bacteriano. Concluiu-se que as feridas tratadas com o mel cicatrizaram mais rápido em relação às tratadas com o açúcar mascavo, demonstrando a maior propriedade cicatrizante do mel em relação ao açúcar mascavo.