Hydrazinium thiocyanate as a reagent for determination of copper

Hydrazinium thiocyanate, N2H5SCN, has been used for the determination of copper in copper salts. The reagent reduces the copper ions to the cuprous state and precipitates cuprous thiocyanate Cu2(SCN)2, quantitatively.

Synthesis of Thioesters by Simultaneous Activation of Carboxylic Acids and Alcohols Using PPh3/NBS with Benzyltriethylammonium Tetrathiomolybdate as the Sulfur Transfer Reagent

A new and simple route for the synthesis of thioesters starting from carboxylic acids and alcohols is reported by using tetrathiomolybdate as the key sulfur transfer reagent. Triphenylphosphane and N-bromosuccinimide were used for the activation of the carboxylic acid and alcohol in the same pot followed by the transfer of sulfur from tetrathiomolybdate. Thioesters were obtained in good to moderate yields. Primary alcohols show excellent reactivity and gave good yields of the corresponding thioesters, whereas secondary alcohols gave moderate yields and tertiary alcohols were very less reactive and gave poor yields of the corresponding thioesters.

Folin-Ciocalteu reagent for the estimation of siderochromes

1. A simple method has been devised for the estimation of siderochromes based on their reaction with Folin-Ciocalteu reagent to give a blue complex under alkaline conditions. 2. The applicability of the method to biological systems has been tested with N. crassa and concentrations in the ranges 5–50 μg and 1–10 μg can be accurately estimated with an over-all recovery of 95%.

Potassium phosphate as a reagent for the gravimetric estimation of lithium

Previous attempts for the quantitative estimation of lithium as orthophosphate, employing an alkali metal phosphate, have not been successful. A method, is described for the estimation of lithium as trilithium phosphate from 60% ethyl alcohol solution at 65° to 70° C., employing potassium phosphate reagent, at pH 9.5. The method is applicable in the presence of varying amounts of sodium and/or potassium cations and chloride, sulfate, nitrate, and phosphate anions.

Bearing capacity of interfering multiple strip footings by using lower bound finite elements limit analysis

The ultimate bearing capacity of a number of multiple strip footings, identically spaced and equally loaded to failure at the same time,is computed by using the lower bound limit analysis in combination with finite elements. The efficiency factor due to the component of soil unit weight, is computed with respect to changes in the clear spacing (xi(gamma)) between the footings. It is noted that the failure load for a footing in the group becomes always greater than that of a single isolated footing. The values of xi(gamma) for the smooth footings are found to be always lower than the rough footings. The values ofxi(gamma) are found to increase continuously with a decrease in the spacing between footings. As compared to the available theoretical and experimental results reported in literature, the present analysis provides generally a little lower values of xi(gamma). (C) 2010 Elsevier Ltd. All rights reserved.

Effect of insertion of buffer-strip on the response of carbon-epoxy system in short beam tests

dThe work looks at the response to three-point loading of carbon-epoxy (CF-EP) composites with inserted buffer strip (BS) material. Short beam Shear tests were performed to study the load-deflection response as well as fracture features through macroscopy on the CF-EP system containing the interleaved PTFE-coated fabric material. Significant differences were noticed in the response of the CF-EP system to the bending process consequent to the architectural modification. It was inferred that introduction of small amounts of less adherent layers of material at specific locations causes a decrement in the load carrying capability. Further the number and the ease with which interface separation occurs is found to depend on the extent to which the inserted layer is present in either single or multiple layer positions.

Position-sensitive silicon strip detector characterization using particle beams

Silicon strip detectors are fast, cost-effective and have an excellent spatial resolution. They are widely used in many high-energy physics experiments. Modern high energy physics experiments impose harsh operation conditions on the detectors, e.g., of LHC experiments. The high radiation doses cause the detectors to eventually fail as a result of excessive radiation damage. This has led to a need to study radiation tolerance using various techniques. At the same time, a need to operate sensors approaching the end their lifetimes has arisen. The goal of this work is to demonstrate that novel detectors can survive the environment that is foreseen for future high-energy physics experiments. To reach this goal, measurement apparatuses are built. The devices are then used to measure the properties of irradiated detectors. The measurement data are analyzed, and conclusions are drawn. Three measurement apparatuses built as a part of this work are described: two telescopes measuring the tracks of the beam of a particle accelerator and one telescope measuring the tracks of cosmic particles. The telescopes comprise layers of reference detectors providing the reference track, slots for the devices under test, the supporting mechanics, electronics, software, and the trigger system. All three devices work. The differences between these devices are discussed. The reconstruction of the reference tracks and analysis of the device under test are presented. Traditionally, silicon detectors have produced a very clear response to the particles being measured. In the case of detectors nearing the end of their lifefimes, this is no longer true. A new method benefitting from the reference tracks to form clusters is presented. The method provides less biased results compared to the traditional analysis, especially when studying the response of heavily irradiated detectors. Means to avoid false results in demonstrating the particle-finding capabilities of a detector are also discussed. The devices and analysis methods are primarily used to study strip detectors made of Magnetic Czochralski silicon. The detectors studied were irradiated to various fluences prior to measurement. The results show that Magnetic Czochralski silicon has a good radiation tolerance and is suitable for future high-energy physics experiments.

Benzyltriethylammon Tetrathiomolybdate: An Improved Sulfur Transfer Reagent for the Synthesis of Disulfides

Benzyltriethylammonium tetrathiomolybdate has been found to be a superior reagent for the conversion of alkyl halides to the corresponding disulfides in chloroform at room temperature.