Aplicação da alvenaria estrutural em sistemas de armazenamento de produtos agrícolas a granel

O armazenamento de produtos agrícolas cumpre um papel importante no agronegócio. Observa-se uma tendência cada vez maior em se trabalhar com produtos a granel, em grandes volumes. Visando a uma concepção construtiva racional e econômica, o presente trabalho propõe um sistema misto em concreto armado e alvenaria estrutural aplicado a silos para armazenagem de produto agrícola a granel. No projeto proposto, o silo é composto de células em alvenaria estrutural, geminadas duas a duas na largura e com um número variável de células no comprimento, em função do volume desejado de armazenagem. Esse sistema simétrico favorece a racionalidade operacional, garantindo a continuidade entre os fluxos de recebimento e de expedição. O fundo da célula é em forma de tremonha dupla troncopiramidal, com saída central, construída em painéis treliçados pré-moldados. A sustentação das células e das tremonhas é feita através de vigas e de pilares de concreto armado. O isolamento térmico necessário para que a qualidade do produto armazenado seja garantida é estabelecido pela utilização de telhas trapezoidais de aço galvanizado, tanto na cobertura como nos fechamentos laterais. A fim de ilustrar o presente trabalho, um exemplo de silo utilizando o sistema proposto é apresentado, e a viabilidade da concepção construtiva adotada é analisada.

Tipologia de instalações avícolas na região Agreste de Pernambuco

RESUMOEste estudo foi conduzido com o objetivo de caracterizar a tipologia das instalações para produção de frangos de corte na região Agreste do Estado de Pernambuco, por meio de levantamento das características construtivas de aviários existentes na região. Foram avaliados 68 galpões, em 27 granjas, no período de maio de 2012 a abril de 2013. Com base nos resultados obtidos, 90% das instalações apresentaram orientação leste - oeste, com pequeno afastamento entre galpões (< 30 m). A maioria dos galpões apresentou cobertura com telhas cerâmicas (93%), ausência de forro (93%) e lanternim (100%), pé-direito abaixo do recomendado (90%), beirais menores que 1,25 m (93%) e muretas com altura superior a 0,2 m (40%). Quanto aos equipamentos, observou-se que a principal fonte de aquecimento foi por campânulas à lenha (71%), comedouros e bebedouros automatizados (46 e 35%) e pendulares (54 e 65%). Aproximadamente, 67% dos galpões possuíam ventiladores e 58% destes estavam associados à nebulização. O levantamento permitiu caracterizar o perfil das instalações e suas necessidades de adequação para a melhoria da condição de alojamento das aves na região.

Caracterização de impactos ambientais de indústrias de cerâmica vermelha do estado do Rio Grande do Sul

Os impactos ambientais ligados à construção civil têm despertado interesse de vários pesquisadores. Entre estes impactos estão os diretamente relacionados à produção de materiais de construção. No Brasil, existem poucos estudos que avaliam estes impactos. Esses estudos são fundamentais para a definição de requisitos que permitam aos principais atores do setor optarem por materiais baseados tanto no desempenho técnico, como também no desempenho ambiental. O objetivo desta pesquisa é caracterizar os principais impactos envolvidos na produção de tijolos, blocos e telhas cerâmicas no estado do Rio Grande do Sul, visando apontar iniciativas ambientais adotadas e melhorias a serem incorporadas. Para se atingir o objetivo, um grupo de 8 indústrias de pequeno, médio e grande porte foram selecionadas para comporem o múltiplo estudo de caso. Os dados foram obtidos através de aplicação de entrevistas realizadas junto às indústrias. Os principais impactos analisados dizem respeito à: matéria-prima, fontes energéticas, geração de resíduos, emissões de CO2, ambiente de trabalho e produto acabado. Através da pesquisa verificou-se que as indústrias possuem iniciativas de baixo impacto ambiental, como o uso de fontes renováveis de energia e resíduos de outras indústrias incorporados a sua matéria-prima. Observa-se a necessidade de diminuir perdas no processo de produção, que são elevadas, bem como melhorar as condições de trabalho e organização do processo.

Levantamento de manifestações patológicas em revestimentos de fachadas das edificações da cidade de Pelotas

Os revestimentos são, do ponto de vista funcional, integrantes das vedações e fundamentais para a durabilidade dos edifícios, contribuindo para o bom aspecto das fachadas. A identificação e correção das possíveis falhas certamente aumentam o grau de satisfação da população de maneira geral por sua contribuição para a estética da cidade, além de contribuir para aumentar a vida útil do produto e de seu valor comercial. Este trabalho apresenta os resultados de levantamento de dados realizado em edificações da zona urbana da cidade de Pelotas, com o objetivo de levantar dados sobre as manifestações patológicas nos revestimentos de seus paramentos exteriores, identificando aspectos relacionados aos materiais, tipo de lesões, incidência, etc. Por meio de observação in loco, foram analisadas 424 fachadas de edificações, sendo os dados coletados com o auxílio de um instrumento composto por duas fichas: a primeira, dividida em duas partes, serviu para identificar o responsável pelo seu preenchimento, bem como para identificar e caracterizar a edificação, enquanto que a segunda ficha, serviu para caracterizar as lesões encontradas nos revestimentos. Os dados coletados foram analisados por meio do software estatístico SPSS. As informações foram organizadas em dois bancos de dados, um para registro das informações referentes à edificação e outro para as informações referentes às lesões. Os resultados permitiram concluir que as edificações analisadas, de um modo geral, foram construídas antes de 1970, com paredes de tijolos cerâmicos, revestidas com argamassas inorgânicas e pintadas, cobertura de telhas cerâmicas, esquadrias de madeira e para uso residencial. O estado de conservação é razoável, apresentando com mais freqüência, três lesões por fachada. As lesões mais freqüentes são: manchas de sujeira ou vegetação parasitária, umidade ascensional, descolamento em placas, descoloração e fissuras.

Avaliação da potencialidade de argilas do Rio Grande do Norte – Brasil

DUTRA, Ricardo Peixoto Suassuna ; SILVA, Jaquelígia Brito da ; MORAES, Márcio Luiz Varela Nogueira de ; NASCIMENTO, R. M. ; GOMES, Uilame Umbelino ; PASKOCIMAS, Carlos Alberto . Avaliação da potencialidade de argilas do Rio Grande do Norte. Cerâmica Industrial, v. 13, p. 47-50, 2008.

A cultura de índio, seu menino, vem de longe aqui : formação histórica e territorialização dos Tremembé/CE

This dissertation is based on the ethnography of a strategic selection of three Tremembé ethnic situations, which are situated in the backlands of Acaraú and Itarema, municipalities located in Ceará State (Northeast Brazil). My main aims are the following. Firstly, I reconstitute the historical and social formation of three localities, called Lagoa dos Negros, Telhas, and Queimadas, related to a particular origin myth which refers to Almofala, an extinct colonial Aldeamento in the seashore, where the Tremembé indians and other native populations were converted and gathered under missionary administration. According to the origin myth, these three localities were set up after a strong drought which happened in 1888 (the so called three eights) when a group of Tremembé families moved to the countryside and established close to the Lagoa dos Negros and, later on, they were segmented into smaller groups which started to live in other areas and places not far from the former location. Notably, I develop an anthropological approach to understand the historical formation of these three localities. Secondly, I analyze some processes of territorialization, which were emerged from the 1980s and had important consequences to these indigenous families throughout the next two decades. This historical dimension is re-appropriated and ressignified in ethnic terms. A third point of my work is the analysis of the construction of territorialities and also the cultural and symbolic dimensions which are formulated by the Tremembé Indians who live in these localities. Therefore, I investigate some cultural traditions and rituals, such as the Torém dance, but I also examine their multiple semantics, which constitute a transversal direction throughout the history understood by the Tremembé of the different social situations I researched. To sum up, there is a process of cultural actualization, which is still going on and presents itself through the ludic sphere as well as their political and religions dimensions, which are usually associated to the ritual presentation of the Torém

Influência do teor de calcário no comportamento físico, mecânico e microestrutural de cerâmicas estruturais

There are ores of clay in Piauí State that are used for red structural ceramics, which are naturally contaminated with calcareous vein. This is one thing that impedes its exploration in an adequate way, especially for tile production. The present work aims at verifying the influence of the calcareous contents in the technological structural ceramics area, seeking to determine a maximum permissible calcareous proportion/contents in the ceramic mass using the patterns of the local industry production. For the consecution of this paper, it was characterized the clay and calcareous material by FRX, DRX, TGA and DTA. It was also configurated by extrusion and burnt in the temperatures of 850°C, 900°C, 950°C and 1000°C pieces of the corpus with 0, 5, 10, 15 e 20% of calcareous proportion. After that, it was carried out technological samples of linear retraction, water absortion, apparent porosity, specific apparent mass and mechanic resistance. The results showed the possibility of using calcareous in the ceramic mass and in some cases the technological properties got better

Desenvolvimento de cerâmica vermelha utilizando rejeitos da construção civil

The Industry of the Civil Construction has been one of the sectors that most contribute to the pollution of the environment, due to the great amount of residues generated by the construction, demolition and the extraction of raw material. As a way of minimizing the environmental impacts generated by this industry, some governmental organizations have elaborated laws and measures about the disposal of residues from the building construction (CONAMA - resolution 307). This work has as objective the reutilization of residues compound of sand, concrete, cement, red bricks and blocks of cement and mortar for the production of red ceramic, with the objective of minimizing costs and environmental impacts. The investigated samples contained 0% to 50% of residues in weight, and they were sintered at temperatures of 950°C, 1000°C, 1050°C, 1100°C and 1150°C. After the sinterization, the samples were submitted to tests of absorption of water, linear retraction, resistance to bending, apparent porosity, specific density, XRD and SEM. Satisfactory results were obtained in all studied compositions, with the possible incorporation of up to 50% of residues in ceramic mass without great losses in the mechanical strength, giving better results to the incorporation of 30% of residues in the fabrication of ceramic parts, such as roofing tiles, bricks masonry and pierced bricks

Influência do lodo de ETE na massa para fabricação de cerâmica vermelha

The WTP produce many kinds of residue on your treatment stages, but the sludge is the more problematic from the final disposition point view. The actual rate of residue production deriving from technological evolution and the crescent population needs prevents the subtle equilibrium generation between consumption and recycling/reuse, creating problems of pollution resulting from inappropriate management of residues. Thus, is necessary achieve a new equilibrium between the grow from raw materials and energy and the residue generation. This equilibrium should be achieved by technical and economic feasibility of environmental supported models through recycling and reuse. The red ceramic industry stand out in residue absorption question as raw material due their clay mass heterogeneity, constituted by clay minerals and non-clay minerals with wide mineralogical variation, allowing residue inclusion which act like plastic or non-plastic materials, contributing to retain heavy metals contained in residues in the vitreous mass formed during the burning of the ceramic bodies. This work propose the study of the influence of incorporation of 25 wt.% sludge from wastewater treatment plant, according preliminary results, in the mass to produce ceramic bodies. The raw materials was characterized through chemical composition analyses by XRF, mineralogical analyses by XRD, thermal analyses by TG and DTA, Atterberg limits and thermodilatometry. Subsequently was composed the mass with 75 wt.% of clay and 25 wt.% of dried wastewater sludge from UFRN WWTP. Samples with 6,0 x 2,0 x 0,5 cm was produced with unidirectional compacting under pressure of 20MPa and burned in temperatures between 950 and 1,200ºC. After fired, the ceramic bodies have been submitted to physical and mechanical analyses through the measure of firing shrinkage, water absorption, density, apparent porosity and flexural strength; crystallographic analyses through XRD and microstructure analyses by SEM. The technological properties obtained was satisfactory to production of roof tiles with 25 wt.% at 1,200 ºC, but the production of others products at lower temperatures was not feasible

Efeito da adição de carbonatos em formulação de massa para revestimento cerâmico utilizando matérias-primas do Piauí

Piauí state is a major producer of traditional red ceramic burning as bricks, tiles and ceramic tiles, with its main production center located in the city of Teresina. The state has large reserves of raw materials that can be used in the ceramic coating as clays, quartz, talc and carbonates. However, in the preparation of ceramic bodies using only a mixture of clays with different characteristics. The study aims to evaluate the effect of adding two types of carbonates in the ceramic semiporous mass coating produced in Piauí and then to verify the potential use of these carbonates as supplementary raw material product manufactured or the feasibility of obtaining a ceramic plate that meets the specifications for the porous coating. For this, were characterized the ceramic Piauí coating mass, a calcitic carbonate and a dolomitic, were made in the levels of 2, 4, 8, 16, and 32%. The masses were formed by pressing and burneds in two environments: a laboratory furnace (1080°C, 1120°C, 1140°C, and 1160°C) and an industrial furnace (1140°C). Then, following tests of linear shrinkage water absorption, apparent porosity, bulk density and flexural strength. Furthermore, the fired specimens were tested for their macrostructure and microstructure. The results showed the possibility of using the carbonate in ceramic mass flooring produced in Piauí, as added in small proportions improved dimensional stability and increased mechanical strength of ceramics pieces. It also proved itself possible to produce porous coating when added in higher levels

Estudo da adição de resíduo de scheelita em matriz cerâmica: formulação, propriedades físicas e microestrutura

Extractivism mineral is considered an activity highly degrading, due to the large volume of material that he moves in the form of ore and residues. The vast majority of mining companies do not show any technology or economically viable application that will allow the recycling of mineral residue, these being launched in areas receiving located the "open skies" degrade the environment. In Rio Grande do Norte to the production of ceramic red restricts their activities to the production of products such as: solid bricks, ceramic blocks, tiles, among others. Seeking to unite experiences and technical information that favor sustainable development, with important benefits to the construction sector and civil society in general, the present work studies the incorporation of the residue of scheelite in ceramic matrix kaolinitic, coming from the municipality of Boa Saúde - RN, in percentage of 5 %, 10 %, 20 %, 30% 40% and 50 %, by evaluating its microstructure, physical properties and formulation. The raw materials were characterized through the trials of X ray fluorescence, Diffraction of X rays, Differential Thermal Analysis and Termogravimetric Analysis. The samples were formed and fired at temperatures of 850o, 900o, 1000o, 1050o, 1100o, 1150o and 1200 oC, with isotherm of 1 hour and heating rate of 10 oC/min. Assays were performed technological of loss to fire, Water Absorption, Apparent Porosity, Apparent Density, Mass Loss in Fire and Bending Resistance; in addition to the Scanning Electron Microscopy, analyzing their physical and mechanical properties. The use of residue of scheelite in ceramic mass kaolinitic provided a final product with technological properties that meet the technical standards for the production of bricks and roofing tiles, with the percentage of 20% of waste that showed the best results

Estudo da potencialidade da incorporação de resíduo de granito e da queima da casca do café em cerâmica vermelha

The industrial production of ornamental rocks and the burning of coffee husk generate waste that is discarded into the environment. However, with the study of the incorporation of these residues in ceramic products, may be found an alternative to reducing environmental impacts and detrimental effects on human health caused by its indiscriminate disposal of waste in nature. Thus, this work aimed to study the addition of ashes of the coffee husk and granite residue in matrix of red ceramic. The raw materials were dry milled and sieved to mesh 100. To characterize the raw materials were carried out analyzes of X-ray diffraction (XRD), X-ray fluorescence (XRF), particle size analysis (PSA), differential thermal analysis (DTA) and thermogravimetric analysis (TG). Six formulations were prepared where the clay content was kept constant (70%wt) and ashes contents and granite residue varied from 10, 15, 20 and 30%. Dilatometrics analyzes were performed at four selected formulations, containing them: 100% clay (A100); 70% clay and 30% ashes (A70C30); 70% clay and 30% granite residue (A70G30); and 70% clay, 15% granite residue and 15% ashes (A70G15C15). The samples were prepared by uniaxial compaction with pressure of 25 MPa, and fired at temperatures of 800°C, 850ºC, 900ºC, 950ºC, 1000ºC and 1100°C. Assays were performed to determine the linear shrinkage of burning (LSB), water absorption (WA), apparent porosity (AP), density (D) and tensile bending. Also were performed analyzes of X-ray diffraction (XRD) and scanning electron microscopy (SEM) of the samples fired. The formulations incorporating granite residue and/or ashes reached the required limits of water absorption according to NBR 15270-1 and NBR 15310 and tensile bending according to classical literature (SANTOS, 1989) necessary for the production of tiles and ceramic block for masonry sealing

Avaliação da incorporação combinada dos resíduos de cascalho de perfuração de poço de petróleo e de polimento do porcelanato em cerâmica vermelha

Among the industries, those that produce ceramic porcelain for use in construction industry and oil, during the exploration and production period, play an important role in the production of waste. Much research has been carried out both by academia and the productive sector, sometimes reintroducing them in the same production line that generated them, sometimes in areas unrelated to their generation, as in the production of concrete and mortar for the construction, for example, but each one in an isolated way. In this research, the aim is to study the combined incorporation of the waste drill cuttings of oil well and the residue of the polishing of porcelain, generated in the final stage of finishing of this product in a clay matrix, for the production of red pottery, specifically bricks, ceramic blocks and tiles. The clay comes from the municipality of São Gonçalo, RN, the drilling waste is from the Natal basin, in Rio Grande do Norte, and the residue of the polishing proceeds from a ceramic porcelain of the State of Paraíba. For this purpose, we used a mixture of a plastic clay with a non-plastic, in a ratio of 50% each, settling formulations with the addition of these two residues in this clay matrix. In the formulations, both residues were incorporated with a minimum percentage of 2.5% and maximum of 12.5%, varying from 2.5% each, in each formulation, which the sum of the waste be no more than 15%. It should be noted that the residue of the polishing of ceramic porcelain is a IIa class (not inert). The materials were characterized by XRF, XRD, TG, DTA, laser granulometry and the plasticity index. The technological properties of water absorption, apparent porosity, linear shrinkage of burning, flexural tensile strength and bulk density were evaluated after the sintering of the pieces to 850 °C, 950 °C and 1050 °C, with a burning time of 3 hr, 3 hr and 30 minutes, and 3 hr and 50 minutes, respectively, with a heating rate of 10 °C/minute, for all formulations and landing of 30 minutes. To better understand the influence of each residue and temperature on the evaluated properties, we used the factorial planning and its surfaces of response for the interpretation of the results. It was found that the temperature has no statistical significance at a 95% of reliability level in flexural tensile strength and that it decreases the water absorption and the porosity, but increases the shrinkage and the bulk density. The results showed the feasibility of the desired incorporation, but adjusting the temperature to each product and formulation, and that the temperatures of 850 °C and 950 °C were the one that responded to the largest number of formulations

Thermal comfort indices in individual shelters for dairy calves with different types of roofs

Dentre os materiais de construção utilizados nas instalações rurais, merecem destaque as coberturas, pois são grandes responsáveis pelo conforto térmico, influenciando no balanço térmico no interior das instalações. Este trabalho objetivou avaliar a influência das coberturas sobre a entalpia (H), Carga Térmica Radiante (CTR) e no Índice de Temperatura de Globo Negro e Umidade (ITGU), em abrigos individuais para bezerros leiteiros. O delineamento foi o inteiramente casualizado com três tratamentos: Z - telha de zinco; CA - telha de cimento amianto, e CAB - telha de cimento amianto pintada de branco na face superior. As médias foram comparadas pelo teste de Scott Knott, a 1% de probabilidade. Os resultados mostraram que não houve diferença estatística entre os tratamentos (P<0,01) e o ambiente externo, para a H. Para a CTR, houve diferença estatística entre todos os tratamentos, em que CAB demonstrou menor CTR, 489,28 W m-², seguido do tratamento CA, 506,72 W m-², e Z com maior valor de CTR, 523,55 W m-². Para o ITGU, observaram-se menores valores para CAB (76,8) e CA (77,4), diferindo-se, significativamente do Z, que obteve maior valor (81,6). As telhas com pintura branca em sua face superior promoveram menor CTR e menor ITGU, favorecendo o ambiente térmico da instalação.

Efeito da introdução de resíduo de cinza de forno cerâmico em massa para cerâmica estrutural

The red ceramics and structural ceramics, as they are known, include ceramic materials made by blocks of seals and structures, bricks, tiles, smail flagstones manacles, rustic floors and ornamental materials. Their fabrication uses raw material such as clay and clay sites, with some content of impurity. It has good durability and mechanical strength to compression, low cost, making it one of the mainly used materials in civil engineering. The incorporation of many industrial activities residue to ceramic products is a technological alternative for reducing the environmental impact caused by its carefree disposal. This incorporation can promote chemical change and inertness of metals from residue, by fixation in the glassy phase of ceramic during the burning stage. The main aim of this project is to study the technical feasibility of the addition of ceramic oven ash into formulations of mass for structural ceramics. In this project two kinds of clay (plastic and non-plastic) were used, as well as the ash from firewood used in the process of burning of structural ceramics. A group of experiments was outlined, which permitted the evaluation of the influence of the burning cycle in different temperatures of the ash content in formulations for ceramic blocks through technological properties, mechanical behavior and microstructure. Five samples were processed of each one of the masses of plastic and non-plastic clay without addition of ash and with addition of ash on the percentages of 10 % and 20 %, for temperatures of 850 °C, 950 °C, 1050 °C and 1150 °C, obtained through sinterization process. Among the studied compositions, the one which presented best performance was the mass of clay with 10 % of ash, at temperature of 1150 °C, with the smallest absorption of water, the smallest apparent porosity, specific apparent mass a bit over the others and greatest mechanical resistance to flexion. The composition made confirmed the technical feasibility of the use of ash in the mass for structural ceramics with maintenance of its necessary characteristics for its purposes