Manipulator trajectory planning using a MOEA

Generating manipulator trajectories considering multiple objectives and obstacle avoidance is a non-trivial optimization problem. In this paper a multi-objective genetic algorithm based technique is proposed to address this problem. Multiple criteria are optimized considering up to five simultaneous objectives. Simulation results are presented for robots with two and three degrees of freedom, considering two and five objectives optimization. A subsequent analysis of the spread and solutions distribution along the converged non-dominated Pareto front is carried out, in terms of the achieved diversity.

Design and Development of a Remotely Operated Underwater Multi-Robot Manipulator Controller

For the scientific and commercial utilization of Ocean resources, the role of intelligent underwater robotic systems are of great importance. Scientific activities like Marine Bio-technology, Hydrographic mapping, and commercial applications like Marine mining, Ocean energy, fishing, aquaculture, cable laying and pipe lining are a few utilization of ocean resources. As most of the deep undersea exploration are beyond the reachability of divers and also as the use of operator controlled and teleoperated Remotely Operated Vehicles (ROVs) and Diver Transport Vehicles (DTVs) turn out to be highly inefficient, it is essential to have a fully automated system capable providing stable control and communication links for the unstructured undersea environment.

Design and development of a dextrous manipulator

This paper develops a novel method of actuation for robotic hands. The solution employs Bowden cable routed to each joint as the means by which the finger is actuated. The use of Bowden cable is shown to be feasible for this purpose, even with the changing frictional forces associated with it's use. This method greatly simplifies the control of the hand by removing the coupling between joints, and allows for direct and accurate translation between the joints and the motors driving the Bowden wires. The design also allows for two degrees of freedom (with the same centre of rotation) to be realised in the largest knuckle of each finger, meaning biological finger kinematics are more accurately emulated.

Design and development of a dextrous manipulator

This paper describes a novel method of actuation for robotic hands. The solution employs a Bowden cable routed to each joint. The use of a Bowden cable is shown to be feasible for this purpose, ever, with the changing frictional forces associated with it. This method greatly simplifies the control of the hand by removing the coupling between joints, and provides for direct and accurate translation between the joints and the servo motors driving the cables. The design also allows for two degrees of freedom with the same centre of rotation to be realized in the largest knuckle of each finger; thus biological finger kinematics are more closely emulated.

Visual sensor fusion for active security in robotic industrial environments

This work presents a method of information fusion involving data captured by both a standard CCD camera and a ToF camera to be used in the detection of the proximity between a manipulator robot and a human. Both cameras are assumed to be located above the work area of an industrial robot. The fusion of colour images and time of light information makes it possible to know the 3D localization of objects with respect to a world coordinate system. At the same time this allows to know their colour information. Considering that ToF information given by the range camera contains innacuracies including distance error, border error, and pixel saturation, some corrections over the ToF information are proposed and developed to improve the results. The proposed fusion method uses the calibration parameters of both cameras to reproject 3D ToF points, expressed in a common coordinate system for both cameras and a robot arm, in 2D colour images. In addition to this, using the 3D information, the motion detection in a robot industrial environment is achieved, and the fusion of information is applied to the foreground objects previously detected. This combination of information results in a matrix that links colour and 3D information, giving the possibility of characterising the object by its colour in addition to its 3D localization. Further development of these methods will make it possible to identify objects and their position in the real world, and to use this information to prevent possible collisions between the robot and such objects.

Visual sensor fusion for active security in robotic industrial environments

This work presents a method of information fusion involving data captured by both a standard charge-coupled device (CCD) camera and a time-of-flight (ToF) camera to be used in the detection of the proximity between a manipulator robot and a human. Both cameras are assumed to be located above the work area of an industrial robot. The fusion of colour images and time-of-flight information makes it possible to know the 3D localization of objects with respect to a world coordinate system. At the same time, this allows to know their colour information. Considering that ToF information given by the range camera contains innacuracies including distance error, border error, and pixel saturation, some corrections over the ToF information are proposed and developed to improve the results. The proposed fusion method uses the calibration parameters of both cameras to reproject 3D ToF points, expressed in a common coordinate system for both cameras and a robot arm, in 2D colour images. In addition to this, using the 3D information, the motion detection in a robot industrial environment is achieved, and the fusion of information is applied to the foreground objects previously detected. This combination of information results in a matrix that links colour and 3D information, giving the possibility of characterising the object by its colour in addition to its 3D localisation. Further development of these methods will make it possible to identify objects and their position in the real world and to use this information to prevent possible collisions between the robot and such objects.

Kinematic and dynamic modeling of a robotic head with linear motors

Our present research focuses on kinematic and dynamic modeling of a 3-DOF robotic cutting head for the next generation of CNC machines. The robotic cutting head is one kind of parallel manipulator of 3-PUU type, which has a high flexibility of motion in three-dimensional space. The parallel manipulator consists of three linear servomotors, which drive three connecting rods independently according to the cutting strategy. Being a parallel manipulator, the robotic cutting head has higher stiffness and position accuracy; consequently, higher velocities and accelerations can be achieved. A very suitable application of this mechanism is as a cutting head of a precision machine tool for three-dimensional cutting problems.

Designing optimal fault tolerant Jacobian for robotic manipulators

Fault tolerance of robotic manipulators is determined based on the fault tolerance measures. In this study a Jacobian of a 7DOF optimal fault tolerant manipulator is designed based on optimality of worse case relative manipulability and worse case dexterity from geometric perspective instead of numerical solution of constrained optimisation problem or construction of optimal Jacobean through a desired null space. The proposed Jacobean matrix is optimal and equally fault tolerant for a single joint failure within any joint of the manipulators.

Optimal fault-tolerant robotic manipulators

This thesis addresses “Optimal Fault-Tolerant Robotic Manipulators” for locked-joint failures and consists of three components. It begins by investigating the regions of workspace where the manipulator can operate with high reliability. It then continues with an efficient deployment of kinematic redundancies for fault-tolerant operation. Finally, it presents a novel method for design of optimal fault-tolerant manipulators.

Next generation robotic counter IED technology : A step change in capability

Improvised Explosive Devices (IEDs) are reported as the number one cause of injury and death for allied troops in the current theater of operation. Deakin University’s Centre for Intelligent Systems Research (CISR) is working on next-generation technology to combat the threat. In 2006 CISR was awarded funding through the Capability and Technology Demonstrator (CTD) Program managed by the Australian Defence Force. The objective was to investigate the use of haptics or force feedback technology for Counter-IED (CIED) tasks. Over the past six years, engineers from CISR have worked alongside Defence stakeholders to develop a series of robotic platforms designed to immerse a soldier in the remote environment. Utilising a natural user interface, haptic force feedback and stereovision, the technology has undergone initial trials in Sydney, Canberra, Woomera and at the CISR testing facility in Geelong, Australia. The technology has proved popular among operators allowing them increased fidelity and manipulation speed while significantly reducing required training. CISR has a history of rapidly delivering technology to meet the needs of police and law enforcement in Australia. The OzBot™ series of robots developed in conjunction with the Victorian Police is currently in service and used extensively for hostage negotiation and first responder roles. The CISR robotics group works on technologies that reduce operator fatigue, minimise training liability and maintenance. Over 55 engineers develop simulation environments for increased training availability and continuous improvement to the current range of mobile platforms, including communications range, payload, manipulator reach and capability. This paper describes a number of the technologies, methods and systems developed by CISR for IED neutralisation, with the aim to increasing military awareness of Australian capability.

A hybrid contact state analysis methodology for robotic-based adjustment of cylindrical pair

The peg-in-hole insertion and adjustment operation is one of the most common tasks in the robotic and automatic assembly processes. Fine motion strategies associated with adjustment operations on a peg-in-hole are fundamental manipulations that can be utilised in dynamic assembly and reconfigurable workholding or fixturing systems. This paper presents a comprehensive study of robotic-based height adjustment of a cylindrical pair based on maintaining minimum contact forces between the links. The outer link is held by the end-effector of a six-DOF (Degrees of freedom) serial articulated robot manipulator. The environment represented by the inner link can be either static or dynamic. A force-based approach and a d value approach are established to determine the type of contact that exists between the links of a cylindrical pair, and to extract control parameters. Based on the comparison and analysis of these two approaches, a hybrid methodology is established by combining a d value approach with a force-based approach for contact state determination. Formulations capable of extracting necessary control parameters, which ensure minimum contact forces between the links, are established from both planar and spatial viewpoints under both static and dynamic environmental conditions. Experimental results demonstrate the effectiveness of the proposed methodology.

Formations of robotic swarm: an artificial force based approach

Cooperative control of multiple mobile robots is an attractive and challenging problem which has drawn considerable attention in the recent past. This paper introduces a scalable decentralized control algorithm to navigate a group of mobile robots (swarm) into a predefined shape in 2D space. The proposed architecture uses artificial forces to control mobile agents into the shape and spread them inside the shape while avoiding intermember collisions. The theoretical analysis of the swarm behavior describes the motion of the complete swarm and individual members in relevant situations. We use computer simulated case studies to verify the theoretical assertions and to demonstrate the robustness of the swarm under external disturbances such as death of agents, change of shape etc. Also the performance of the proposed distributed swarm control architecture was investigated in the presence of realistic implementation issues such as localization errors, communication range limitations, boundedness of forces etc.

Robotic grasping and manipulation controller framework: architecture redevelopment

This paper details the further improvements obtained by redesigning a previously offered Manipulation Controller Framework to provide support to an innovative, friction-based object slippage detection strategy employed by the robotic object manipulator. This upgraded Manipulation Controller Framework includes improved slippage detection functionality and a streamlined architecture designed to improve controller robustness, reliability and speed. Improvements include enhancements to object slippage detection strategy, the removal of the decision making module and integration of its functionality into the Motion Planner, and the stream-lining of the Motion Planner to improve its effectiveness. It is anticipated that this work will be useful to researchers developing integrated robot controller architectures and slippage control.

On homoclinic chaos and a control chaos strategy applied to a free-joint nonholonomic manipulator

In this work, the occurrence of chaos (homoclinic scene) is verified in a robotic system with two degrees of freedom by using Poincare-Mel'nikov method. The studied problem was based on experimental results of a two-joint planar manipulator-first joint actuated and the second joint free-that resides in a horizontal plane. This is the simplest model of nonholonomic free-joint manipulators. The purpose of the present study is to verify analytically those results and to suggest a control strategy.

Networked control system for the guidance of a four-wheel steering agricultural robotic platform

A current trend in the agricultural area is the development of mobile robots and autonomous vehicles for precision agriculture (PA). One of the major challenges in the design of these robots is the development of the electronic architecture for the control of the devices. In a joint project among research institutions and a private company in Brazil a multifunctional robotic platform for information acquisition in PA is being designed. This platform has as main characteristics four-wheel propulsion and independent steering, adjustable width, span of 1,80m in height, diesel engine, hydraulic system, and a CAN-based networked control system (NCS). This paper presents a NCS solution for the platform guidance by the four-wheel hydraulic steering distributed control. The control strategy, centered on the robot manipulators control theory, is based on the difference between the desired and actual position and considering the angular speed of the wheels. The results demonstrate that the NCS was simple and efficient, providing suitable steering performance for the platform guidance. Even though the simplicity of the NCS solution developed, it also overcame some verified control challenges in the robot guidance system design such as the hydraulic system delay, nonlinearities in the steering actuators, and inertia in the steering system due the friction of different terrains. Copyright © 2012 Eduardo Pacincia Godoy et al.