Primary production of phytoplankton and chlorophyll a in the southeast Barents Sea in August-September 1998

A study was performed from August 11 to September 3, 1998 in the Pechora Sea, which covered the shallow-water southeastern Barents Sea. Chlorophyll a concentration in the surface layer (C_chls) ranged from 0.08 to 1.15 mg/m**3, while primary production in the water column (C_phs) Varied from 17 to 170 mg C/m**2/day, aver. 75 mg C/m**2/day. Transition from central deep-water (60-190 m) parts of the sea to coastal shallow-water (15-30 m) parts was accompanied by increase of average C_chls values 2.4 times (from 0.21 to 0.51 mg/m**3) and decrease in average C_phs 1.6 times (from 95 to 58 mg C/m**2/day); the latter, in turn, resulted from decrease in thickness of the photosynthetic layer (H_ph) from 55 to 12 m and its relative transparency (H) from 17 to 4 m. This sharp change in H value and absence of a positive feedback between C_chls and C_phs were most probably related to rapid increase in the role of yellow substance and suspended matter in absorption of solar radiation in coastal waters. In sea areas with depths greater than 30 m a deep chlorophyll maximum was observed; at most of stations it located in the 20-35 m deep layer during illumination in photosynthetic active radiation range comprising 0.8-1.5% of its surface value. Parameters of photosynthetic light curves in these regions indicate participation of shade-adapted flora in formation of the deep chlorophyll maximum. In coastal waters characterized by a relatively uniform chlorophyll distribution over the water column no light adaptation of phytoplankton to efficient utilization of low irradiation for photosynthesis was encountered. Thus, a conclusion was made that combination of extremely low values of C_phs and H_ph makes the pelagic ecosystem of the Pechora Sea coastal regions very sensitive to anthropogenic impacts that may increase water turbidity.

Definición de un Modelo Edafogeomorfológico para la Identificación de Necesidades de Manejo y Recuperación de Suelos a Nivel Local. Caso Cuenca Cañada La Gorda, Machiques Colón, Estado Zulia, Venezuela.

El objetivo de este trabajo es generar un modelo Edafogeomorfológico útil en la identificación de necesidades de manejo de suelos, se realizó un estudio en el área de la cuenca Cañada La Gorda Machiques-Colón, estado Zulia, Venezuela, caracterizada por un clima tropical de condición subhúmeda, con duración del periodo de crecimiento (DPC) de 230 días, régimen de humedad Ustic y de temperatura Isohipertémico. Se empleó el enfoque de la ecuación factorial de formación de suelos para el análisis y descripción biofísica de los factores a lo largo de una carena. El relieve caracterizado a partir de fotografías aéreas, imágenes de satélites y de chequeos sistemático mediante transectos en el sentido del flujo del escurrimiento; la vegetación a través del uso de la tierra, la cobertura vegetal, la identificación de las especies dominantes a partir de sus nombres vernáculos y la definición de indicadores de vegetales (Iv). Los suelos fueron descritos y clasificados según la Taxonomía de suelos y valorados mediante el modelo paramétricode Riquier et al. (1970) para determinar el índice de productividad (Ip). Se caracterizaron dos paisajes gemorfológicos: Colinar (C) y Valle (V), seis posiciones geomorfológicas entre ambos paisajes definidas por la sucesión de relieves en el sentido de la pendiente: Tope de colina-loma (TC), mesa conservada (MC), vertientes de mesa alta (VA), media (VM), baja (VB) y valle intracolinar (VI); e igual número de perfiles de suelos representativos, los cuales mostraron edafogénesis muy avanzada con Ip inferiores a 8% en todas las posiciones, exceptuando la VB, con una productividad de 13%. El uso de la tierra es a base de pastoreo semi-intensivo de plantas forrajeras introducidas. Las formaciones vegetales predominante fueron los matorrales y arbustales dispersos, acompañados con restos de una selva tropófila fuertemente afectada por la extracción forestal y la conversión en áreas de pastoreo. Se identificaron 8 Iv, asociados fuertemente con condiciones de físicas e hidrológicas del suelo. El alto impacto de las actividades humanas sobre el suelo y vegetación, expresado a través de los procesos de erosión activa, la ausencia de áreas boscosas y la baja productividad de los sistemas de ganadería reportada para la zona, señalan la necesidad de reorientación del uso actual de la tierra, para lo cual se plantean alternativas como la incorporación de bosques protectores y sistemas agrosilvopastoriles In order to generate an Edaphogeomorphological model to be used for the identification of management requirements of soils, a study was carried out in the area of the Cañada La Gorda watershed, Machiques Colon, Zulia State with a tropical climate, subsumid conditions with a growing period of 230 days, an Ustic soil moisture and Isohypertermic regimes. The soils factorial equation approach was used for the analisis and description of the factors of soil formation throughout a soil catena. Relief was characterized through aerial photographs, satellite images and systematic checks of transects drawn in the sense of surface runoff and also taking into account geomorphological features. Vegetation cover and land use were described and vegetation components were indified by its local names to defined vegetations indicators (VI) for the local conditions. Soils were described and classified according to soil taxonomy and valued by means of a parametric model proposed by Riquier et al, (1970) for determining the productivity index (PI). Two geomorphological landscapes were defined: Hilly and Valley with six positions within the landscapes: hilltop (round or elongated), preserved tableland summit, slopes of high, medium and low tableland and valleys between hills. Representative soils of each position were studied showing a highly advanced degree of edaphogenesis with PI values below 8% in all positions except the valleys with a PI of 13%. Land use type is based on semi intensive pasturing of introduced forage species, with a vegetation of brushwood and scattered shrubs, with some trees relicts of woods affected by timber extraction and turn to grassland Eight VI were identified, highly associated to local physical and hidrological soil conditions. The enormous impact of human activity on soils and vegetation as shown by active erosion processes and absence of wooded areas and the low productivity of livestock systems reported for the area, indicates the necessity of a reorientation of the present land use introducing alternatives like the incorporation of protective woods and agrosilvopastoral management systems.

Alkenones and sea surface reconstruction of sediments from, the Arabian Sea

Deep-sea sediments of two cores from the western (TY93-929/P) and the southeastern (MD900963) Arabian Sea were used to study the variations of the Indian monsoon during previous climatic cycles. Core TY93-929/P was located between the SW monsoon driven upwelling centres off Somalia and Oman, which are characterized by large seasonal sea surface temperature (SST) and particle flux changes. By contrast, core MD900963, was situated near the Maldives platform, an equatorial ocean site with a rather small SST seasonality (less than 2°C). For both cores we have reconstructed SST variations by means of the unsaturation ratio of C37 alkenones, which is compared with the delta18O records established on planktonic foraminifera. In general, the SST records follow the delta18O variations, with an SST maximum during oxygen isotope stage 5.5 (the Last Interglacial at about 120-130 kyr) and a broad SST minimum during isotope stage 4 and 3.3 (approximately 40-50 kyr). The SST difference between the Holocene and the Last Glacial Maximum (LGM) is of the order of 2°C. In both cores the SSTs during isotope stage 6 are distinctly higher by 1-2°C than the cold SST minima during the last glacial cycle (LGM and stage 3). To reconstruct qualitatively the past productivity variations for the two cores, we used the concentrations and fluxes of alkenones and organic carbon, together with a productivity index based on coccolith species (Florisphaera profunda relative abundance). Within each core, there is a general agreement between the different palaeoproductivity proxies. In the southeastern Arabian Sea (core MD900963), glacial stages correspond to relatively high productivity, whereas warm interstadials coincide with low productivity. All time series of productivity proxies are dominated by a cyclicity of about 21-23 kyr, which corresponds to the insolation precessional cycle. A hypothesis could be that the NE monsoon winds were stronger during the glacial stages, which induced deepening of the surface mixed layer and injection of nutrients to the euphotic zone. By contrast, the records are more complicated in the upwelling region of the western Arabian Sea (core TY93-929/P). This is partly due to large changes in the sedimentation rates, which were higher during specific periods (isotope stages 6, 5.4, 5.2, 3 and 2). Unlike core MD900963, no simple relationship emerges from the comparison between the delta18O stratigraphy and productivity records. The greater complexity observed for core TY93-929/P could be the result of the superimposition of different patterns of productivity fluctuations for the two monsoon seasons, the SW monsoon being enhanced during interglacial periods, whereas the NE monsoon was increased during glacial intervals. A similar line of reasoning also could help explain the SST records by the superimposition of variations of three components: global atmospheric temperature, and SW and NE monsoon dynamics.

A Bayesian approach to imposing curvature on distance functions

The estimated parameters of output distance functions frequently violate the monotonicity, quasi-convexity and convexity constraints implied by economic theory, leading to estimated elasticities and shadow prices that are incorrectly signed, and ultimately to perverse conclusions concerning the effects of input and output changes on productivity growth and relative efficiency levels. We show how a Bayesian approach can be used to impose these constraints on the parameters of a translog output distance function. Implementing the approach involves the use of a Gibbs sampler with data augmentation. A Metropolis-Hastings algorithm is also used within the Gibbs to simulate observations from truncated pdfs. Our methods are developed for the case where panel data is available and technical inefficiency effects are assumed to be time-invariant. Two models-a fixed effects model and a random effects model-are developed and applied to panel data on 17 European railways. We observe significant changes in estimated elasticities and shadow price ratios when regularity restrictions are imposed. (c) 2004 Elsevier B.V. All rights reserved.

Malmquist-type indices in the presence of negative data:an application to bank branches

In this paper we develop an index and an indicator of productivity change that can be used with negative data. For that purpose the range directional model (RDM), a particular case of the directional distance function, is used for computing efficiency in the presence of negative data. We use RDM efficiency measures to arrive at a Malmquist-type index, which can reflect productivity change, and we use RDM inefficiency measures to arrive at a Luenberger productivity indicator, and relate the two. The productivity index and indicator are developed relative to a fixed meta-technology and so they are referred to as a meta-Malmquist index and meta-Luenberger indicator. We also address the fact that VRS technologies are used for computing the productivity index and indicator (a requirement under negative data), which raises issues relating to the interpretability of the index. We illustrate how the meta-Malmquist index can be used, not only for comparing the performance of a unit in two time periods, but also for comparing the performance of two different units at the same or different time periods. The proposed approach is then applied to a sample of bank branches where negative data were involved. The paper shows how the approach yields information from a variety of perspectives on performance which management can use.

Micropaleontological investigation of sediment core Kronsmoor

Benthic foraminiferal and calcareous nannofossil assemblages, as well as stable isotope data from the Campanian/Maastrichtian boundary interval (~71.4 to ~70.7 Ma) of the Kronsmoor section (North German Basin), were investigated in order to characterize changes in surface-water productivity and oxygen content at the seafloor and their link to climatic and paleoceanographic changes. A nutrient index based on calcareous nannofossils is derived for the high-latitude, epicontinental North German Basin, reflecting changes in surface-water productivity. Oxygen isotopes of well-preserved planktic foraminiferal specimens of Heterohelix globulosa reflect warmer surface-water temperatures in the lower part of the studied succession and a cooling of up to 2°C (0.5 per mil) in the upper part (after 71.1 Ma). For the lower and warmer part of the investigated succession, benthic foraminiferal assemblages and the calcareous nannofossils indicate well-oxygenated bottom waters and low-surface water productivity. In contrast, the upper part of the succession is characterized by cooler conditions, lower oxygen content at the seafloor and increasing surface-water productivity. It is proposed that the cooling phase starting at 71.1 Ma was accompanied by increasing surface-water mixing caused by westerly winds. As a consequence of mixing, nutrients were advected from sub-surface waters into the mixed layer, resulting in increased surface-water productivity and enhanced organic matter flux to the seafloor. We hypothesize that global sea-level fall during the earliest Maastrichtian (~71.3 Ma), indicated by decreasing carbon isotope values, may have led to a weaker water mass exchange through narrower gateways between the Boreal Realm and the open North Atlantic and Tethys oceans. Both the weaker water mass exchange and enhanced surface-water productivity may have led to slightly less ventilated bottom waters of the upper part of the studied section. Our micro-paleontological and stable isotopic approach indicates short-term (<100 kyr) changes in oxygen consumption at the seafloor and surface-water productivity across the homogeneous Boreal White Chalk succession of the North German Basin.

Análisis bibliométrico del desarrollo científico de las ciencias sociales en México: 1997-2006.

En el presente trabajo se presentan los resultados de una investigación realizada sobre el Área de las Ciencias Sociales en México del período 1997-2006, para conocer algunas características relevantes como su evolución histórica y productividad científica (I+D) a través del volumen de documentos generados, el idioma de publicación, el índice de productividad cronológica, temática y por Entidad Federativa, los patrones de autoría y coautoría nacionales e internacionales, citación y co-citación entre publicaciones, instituciones y sub-disciplinas científicas (frentes de investigación), entre otros, utilizando para tal fin las técnica de investigación documental: análisis bibliométrico. La producción científica en Ciencias Sociales en el período estudiado representó el 8% del total de la producción mexicana, en Humanidades se logró el 1.50% y en Ciencias Aplicadas se alcanzó el 90.5%, de acuerdo a estimaciones realizadas a través de las bases de datos Citation Index del ISI. ABSTRACT During the period 1997-2006, to learn more about some important features concerning this country's historical development and scientific productivity (R & D) through the volume of documents generated, language of publication, the productivity index chronologically, thematically and by state, the patterns of authorship and national and international co-authorship, citation and co-citation between publications, institutions and sub-disciplines in science (research fronts), among other such indicators-- using the technique of documentary research: bibliometric analysis. For scientific production within the studied period, the field of Social Sciences represented 8% of the total of the Mexican production ; the field of Humanities represented 1,50% ; and the field of Applied Sciences represented 90,5% . These were results derived according to estimations made through the Citation Index data bases of the ISI.

Reformas na gestão hospitalar:análise dos efeitos da empresarialização

Tese de Doutoramento em Ciências Sociais na Especialidade de Administração da Saúde

Simulador de dano à formação, aplicado ao Projeto e à execução da perfuração de poços de petróleo

With the high oil price variability, the petroleum and the reservoir engineers are usually face to face on how they can evaluate the well performance and productivity. They can improve high productivity from the well construction to the secondary recoveries, but they have never tried a measurement in the drilling operations about the lower productivity index. As a rule, frequently the drilling operations hear from the reservoir engineering and geology that, if there is a formation damage, probably some drilling operations practices were not done properly or the good practice in petroleum engineering or mud engineering were not observed. The study in this working search is an attempt of how to measure a formation damage just from the project drilling to the drilling operations, with datum from the fields in Brazilian northeast and putting into practice a Simulator developed from the modeling on the theory offered by different experts and sources in formation damage

Evaluación de pollos camperos en producción intensiva y semi-intensiva con suplementación de extracto de quillaja y residuos de hortalizas

En la presente investigación se evaluó: la ganancia diaria de peso, consumo semanal, índice de productividad, mortalidad, conversión alimenticia, costo por kg de carne, pigmentación en tarsos, porcentaje de grasa y el efecto del extracto de quillaja como coccidiostato, bajo dos sistemas de crianza, intensiva y semi-intensiva. El extracto de quillaja fue utilizado al 0,1% de inclusión en el alimento. La investigación se llevó a cabo en la provincia del Azuay, cantón Cuenca, parroquia San Joaquín, sector Balzay Bajo. Se utilizaron 300 pollitos camperos de la estirpe Hubbard variedad redbro S de 1 día de edad. Las aves se distribuyeron de forma aleatoria en un diseño de bloques al azar con 3 tratamientos, cada uno con 5 repeticiones y con 20 pollitos por unidad experimental. Los tratamientos fueron: T1: testigo, aves alojadas en sistema intensivo; T2: aves alojadas en sistema intensivo, más una dieta modificada que consistía en la adición de extracto de quillaja al 0,1%; T3: sistema semi-intensivo con la misma dieta del T2, las aves de este tratamiento a partir del día 28 de edad tuvieron acceso a un área verde delimitada, la cual poseía una mezcla forrajera de raigrás-alfalfa y además se adicionaron a su alimentación residuos de hortalizas propias de la zona. La investigación duró 56 días, no se evidenciaron diferencias significativas en ganancia diaria de peso, índice de productividad, índice de conversión, costo por kg de carne y porcentaje de grasa (p>0,05), mientras que consumo semanal y mortalidad, mostraron diferencias significativas (p<0,05). En las demás variables se evidenció mejor intensidad de pigmentación en T3 (p<0,05), mientras que en la infestación por coccidios no se observó diferencia entre tratamientos (p>0,05), lo que indica que la aplicación de extracto de quillaja tuvo un efecto similar al programa anticoccidial utilizado en T1

Impacto de fusões e aquisições na eficiência e produtividade de operadoras de infraestruturas do mercado financeiro e sistemas de negociação

Dissertação (mestrado)—Universidade de Brasília, Departamento de Administração, Programa de Pós-graduação em Administração, 2016.

Nova técnica para obtenção de fraturas com altíssima condutividade em poços de petróleo

Increase hydrocarbons production is the main goal of the oilwell industry worldwide. Hydraulic fracturing is often applied to achieve this goal due to a combination of attractive aspects including easiness and low operational costs associated with fast and highly economical response. Conventional fracturing usually involves high-flowing high-pressure pumping of a viscous fluid responsible for opening the fracture in the hydrocarbon producing rock. The thickness of the fracture should be enough to assure the penetration of the particles of a solid proppant into the rock. The proppant is driven into the target formation by a carrier fluid. After pumping, all fluids are filtered through the faces of the fracture and penetrate the rock. The proppant remains in the fracture holding it open and assuring high hydraulic conductivity. The present study proposes a different approach for hydraulic fracturing. Fractures with infinity conductivity are formed and used to further improve the production of highly permeable formations as well as to produce long fractures in naturally fractured formations. Naturally open fractures with infinite conductivity are usually encountered. They can be observed in rock outcrops and core plugs, or noticed by the total loss of circulation during drilling (even with low density fluids), image profiles, pumping tests (Mini-Frac and Mini Fall Off), and injection tests below fracturing pressure, whose flow is higher than expected for radial Darcian ones. Naturally occurring fractures are kept open by randomly shaped and placed supporting points, able to hold the faces of the fracture separate even under typical closing pressures. The approach presented herein generates infinite conductivity canal held open by artificially created parallel supporting areas positioned both horizontally and vertically. The size of these areas is designed to hold the permeable zones open supported by the impermeable areas. The England & Green equation was used to theoretically prove that the fracture can be held open by such artificially created set of horizontal parallel supporting areas. To assess the benefits of fractures characterized by infinite conductivity, an overall comparison with finite conductivity fractures was carried out using a series of parameters including fracture pressure loss and dimensionless conductivity as a function of flow production, FOI folds of increase, flow production and cumulative production as a function of time, and finally plots of net present value and productivity index

Avaliação dos principais programas de boas práticas agropecuárias implantados no Brasil para promover a sustentabilidade da cadeia leiteira

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Agronomia e Medicina Veterinária, 2016.