Non-invasive pressure monitoring by hoop strain using Fiber Bragg Grating sensor

Non-invasive, real-time dynamic monitoring of pressure inside a column with the aid of Fiber Bragg Grating (FBG) sensor is presented in the present work. A bare FBG sensor is adhered on the circumference of a pressure column normal to its axis, which has the ability to acquire the hoop strain induced by the pressure variation inside the column. Pressure induced hoop strain response obtained using FBG sensor is validated against the pressure measurements obtained from conventional pressure gauge. Further, a protrusion setup on the outer surface of the column has been proposed over which a secondary FBG sensor is bonded normal to its axis, in order to increase the gauge length of this FBG sensor. This is carried out in order to validate the variation in sensitivity of the protrusion bonded FBG sensor compared to the bare FBG sensor bonded over the surface. A comparative study is done between the two FBG sensors and a conventional pressure gauge in order to establish the capacity of FBG sensor obtained hoop strain response for pressure monitoring inside the column.

Notch sensitivity of circular rings subjected to impact loading

'Notch-sensitive regions' have been observed during a series of experimental investigations into the dynamic plastic behaviour and failure of thin-walled metallic radially notched circular rings with are-shaped supports subjected to concentrated impact loads. The experimental results show that the exterior notches at some regions have no effect on the deformation of the rings, but do have effect at the remaining regions. The notch-sensitive region is theoretically determined by using the equivalent structures technique; fairly good agreement has been reached between the simple theory and the experimental results. Both dimensional and theoretical analyses prove that whether a plastic hinge formed or not at the notched section does not depend on the mean radius of the ring and the input kinetic energy. It depends on the weak coefficient of the notched section and the angle of the support. Generally speaking, there are mainly three failure modes for a notched circular ring with are-shaped support under impact loading: Mode I, large inelastic deformation when the notch is outside the sensitive region, in this case the ring deforms as a normal one; Mode II, large inelastic deformation only at some part of the ring and tearing occurred at the notched sections; Mode III, large inelastic deformation and total rupture occurred at the notched sections. It is believed that the present study could assist the understanding of the dynamic behaviour and failure of other kinds of nonstraight components with macroscopic imperfections under impulsive loading.

Nanostructured giant magneto-impedance multilayers deposited onto flexible substrates for low pressure sensing

Nanostructured FeNi-based multilayers are very suitable for use as magnetic sensors using the giant magneto-impedance effect. New fields of application can be opened with these materials deposited onto flexible substrates. In this work, we compare the performance of samples prepared onto a rigid glass substrate and onto a cyclo olefin copolymer flexible one. Although a significant reduction of the field sensitivity is found due to the increased effect of the stresses generated during preparation, the results are still satisfactory for use as magnetic field sensors in special applications. Moreover, we take advantage of the flexible nature of the substrate to evaluate the pressure dependence of the giant magneto-impedance effect. Sensitivities up to 1 Omega/Pa are found for pressures in the range of 0 to 1 Pa, demostrating the suitability of these nanostructured materials deposited onto flexible substrates to build sensitive pressure sensors.

The myogenic automatism of the systemic heart of Octopus vulgaris (Cephalopoda: Coleoidea): evidence for localized stretch sensitivity and pacing activity

The localization of the stretch sensitivity and myogenic automatism in the systemic heart of Octopus vulgaris has been studied on an isolated preparation in which the ventricle was zoned by ligatures. Each region has been submitted to two different levels of internal hydrostatic pressure (1 and 2 kPa). Only the two atrio-ventricular regions were able to contract regularly when submitted to internal pressure, with a frequency dependent from the pressure value, while the ventricle-aortic region was insensitive to the stretching by internal pressure. This result supports the hypothesis that the automatism in this heart is localized. Electrocardiogram recordings from different areas of an isolated and perfused preparation of the systemic heart ventricle are also reported, which suggest that the electrical activity of the ventricle originates in two narrow areas near the atrio-ventricular valves.

SOI membrane-based pressure sensor in stress sensitive differential amplifier configuration

This paper introduces a pressure sensing structure configured as a stress sensitive differential amplifier (SSDA), built on a Silicon-on-Insulator (SOI) membrane. Theoretical calculation show the significant increase in sensitivity which is expected from the pressure sensors in SSDA configuration compared to the traditional Wheatstone bridge circuit. Preliminary experimental measurements, performed on individual transistors placed on the membrane, exhibit state-the-art sensitivity values (1.45mV/mbar). © 2012 IEEE.

THE SENSITIVITY OF 2D COMPRESSOR INCIDENCE RANGE TO IN-SERVICE GEOMETRIC VARIATION

The loss mechanisms which control 2D incidence range are discussed with an emphasis on determining which real in-service geometric variations will have the largest impact. For the majority of engine compressor blades (Minlet>0.55) both the negative and positive incidence limits are controlled by supersonic patches. It is shown that these patches are highly sensitive to the geometric variations close to, and around the leading edge. The variations used in this study were measured from newly manufactured as well as ex-service blades. Over most the high pressure compressor considered, it was shown that manufacture variations dominated. The first part of the paper shows that, despite large geometric variations (~10% of leading edge thickness), the incidence range responded in a linear way. The result of this is that the geometric variations have little effect on the mean incidence range of a row of blades. In the second part of the paper a region of the design space is identified where non-linear behavior can result in a 10% reduction in positive incidence range. The mechanism for this is reported and design guidelines for its avoidance offered. In the final part of the paper, the linear behavior at negative incidence and the transonic nature of the flow is exploited to design a robust asymmetric leading edge with a 5% increase in incidence range.

Measurement of the unburnt gas temperature in an IC engine by means of a pressure transducer

A novel method of measuring cylinder gas temperature in an internal combustion engine cylinder is introduced. The physical basis for the technique is that the flow rate through an orifice is a function of the temperature of the gas flowing through the orifice. Using a pressure transducer in the cylinder, and another in a chamber connected to the cylinder via an orifice, it is shown how the cylinder temperature can be determined with useful sensitivity. In this paper the governing equations are derived, which show that the heat transfer characteristics of the chamber are critical to the performance of the system, and that isothermal or adiabatic conditions give the optimum performance. For a typical internal combustion engine, it is found that the pre-compression cylinder temperature is related to the chamber pressure late in the compression process with sensitivity of the order of 0.005 bar/K. Copyright © 2010 SAE International.

Pressure data analysis of formula one racing engines

The measured time-history of the cylinder pressure is the principal diagnostic in the analysis of processes within the combustion chamber. This paper defines, implements and tests a pressure analysis algorithm for a Formula One racing engine in MATLAB1. Evaluation of the software on real data is presented. The sensitivity of the model to the variability of burn parameter estimates is also discussed. Copyright © 1997 Society of Automotive Engineers, Inc.

Analysis of high pressure premixed flames using Equivalent Reactor Networks for predicting NOx emissions

This paper describes a computational study of lean premixed high pressure methane-air flames, using Computational Fluid Dynamics (CFD) together with a reactor network approach. A detailed chemical reaction mechanism is employed to predict pollutant concentrations, placing emphasis on nitrogen oxide emissions. The reacting flow field is divided into separate zones in which homogeneity of the physical and chemical conditions prevails. The defined zones are interconnected forming an Equivalent Reactor Network (ERN). Three flames are examined for which experimental data is available. Flame A is characterised by an equivalence ratio of 0.43 while Flames B and C are richer with equivalence ratios of 0.5 and 0.56 respectively. Computations are performed for a range of operating conditions, quantifying the effect in the emitted NOx levels. Model predictions are compared against the available experimental data. Sensitivity analysis is performed to investigate the effect of the network size, in order to define the optimum number of reactors for accurate predictions of the species mass fractions. © 2012 Elsevier Ltd. All rights reserved.

Ultrathin FBG pressure sensor with enhanced responsivity

An ultrathin fiber Bragg grating pressure sensor with enhanced sensitivity is demonstrated. A novel piston-like diaphragm with a hard core in the center is used as the sensing element to enhance the responsivity. Both the theoretical analysis and the experimental results show that the Young's modulus of the diaphragm and the radius of the hard core have significant effect on the pressure responsivity. By optimizing these two parameters, a pressure responsivity of 7 nm/MPa has been achieved.

Investigation on a pressure-gradient fiber laser hydrophone

In this paper, a pressure-gradient fiber laser hydrophone is demonstrated. Two brass diaphragms are installed at the end of a metal cylinder as sensing elements. A distributed feedback fiber laser, fixed at the center of the two diaphragms, is elongated or shortened due to the acoustic wave. There are two orifices at the middle of the cylinder. So this structure can work as a pressure-gradient microphone in the acoustic field. Furthermore, the hydrostatic pressure is self-compensated and an ultra-thin dimension is achieved. Theoretical analysis is given based on the electro-acoustic theory. Field trials are carried out to test the performance of the hydrophone. A sensitivity of 100 nm MPa-1 has been achieved. Due to the small dimensions, no directivity is found in the test.

Preparation and gas sensitivity of octa-n-butoxy-2,3-naphthalocyanine copper(II) Langmuir-Blodgett film

The formation process of monolayer of octa-n-butoxy-2,3-naphthalocyanine copper ( I), [CuNc(OBu)(8)], on water subphase was studied. Its multilayers were successifully deposited on the hydrophilic substrates by Z-type deposition mode using LB technique. Stable solid film with a limiting molecular area of 0.74 nm(2) and a collapse pressure of 55 mN/m were formed. The LB film structure was characterized by IR and electronic absorption spectra. Macrocycle of CuNc (OBu)(8) molecules have a face-to-face arrangement in the multilayers. These films have good sensitivities to vapor of alcohols, with the following sequence of sensitivities: i-PrOH>EtOH>MeOH. The response time and recovery time of the LB films to vapor of MeOH, EtOH and i-PrOH[volume fraction (1-5) X 10(-5)] were within 2 and 5 seconds respectively, while those of the LB films to ammonia(1 X 10(-4)) were 30-60 seconds and 4-5 minutes respectively.

Climate change impacts on sea–air fluxes of CO2 in three Arctic seas: a sensitivity study using Earth observation

We applied coincident Earth observation data collected during 2008 and 2009 from multiple sensors (RA2, AATSR and MERIS, mounted on the European Space Agency satellite Envisat) to characterise environmental conditions and integrated sea-air fluxes of CO2 in three Arctic seas (Greenland, Barents, Kara). We assessed net CO2 sink sensitivity due to changes in temperature, salinity and sea ice duration arising from future climate scenarios. During the study period the Greenland and Barents seas were net sinks for atmospheric CO2, with integrated sea-air fluxes of -36 +/- 14 and -11 +/- 5 Tg C yr(-1), respectively, and the Kara Sea was a weak net CO2 source with an integrated sea-air flux of +2.2 +/- 1.4 TgC yr(-1). The combined integrated CO2 sea-air flux from all three was -45 +/- 18 TgC yr(-1). In a sensitivity analysis we varied temperature, salinity and sea ice duration. Variations in temperature and salinity led to modification of the transfer velocity, solubility and partial pressure of CO2 taking into account the resultant variations in alkalinity and dissolved organic carbon (DOC). Our results showed that warming had a strong positive effect on the annual integrated sea-air flux of CO2 (i.e. reducing the sink), freshening had a strong negative effect and reduced sea ice duration had a small but measurable positive effect. In the climate change scenario examined, the effects of warming in just over a decade of climate change up to 2020 outweighed the combined effects of freshening and reduced sea ice duration. Collectively these effects gave an integrated sea-air flux change of +4.0 TgC in the Greenland Sea, +6.0 Tg C in the Barents Sea and +1.7 Tg C in the Kara Sea, reducing the Greenland and Barents sinks by 11% and 53 %, respectively, and increasing the weak Kara Sea source by 81 %. Overall, the regional integrated flux changed by +11.7 Tg C, which is a 26% reduction in the regional sink. In terms of CO2 sink strength, we conclude that the Barents Sea is the most susceptible of the three regions to the climate changes examined. Our results imply that the region will cease to be a net CO2 sink in the 2050s.

Assessing the sensitivity of seagrass bed biotopes to pressures associated with marine activities.

This project was commissioned to generate an improved understanding of the sensitivities of seagrass habitats to pressures associated with human activities in the marine environment - to provide an evidence base to facilitate and support management advice for Marine Protected Areas; development of UK marine monitoring and assessment, and conservation advice to offshore marine industries. Seagrass bed habitats are identified as a Priority Marine Feature (PMF) under the Marine (Scotland) Act 2010, they are also included on the OSPAR list of threatened and declining species and habitats, and are a Habitat of Principle Importance (HPI) under the Natural Environment and Rural Communities (NERC) Act 2006, in England and Wales. The purpose of this project was to produce sensitivity assessments with supporting evidence for the HPI, OSPAR and PMF seagrass/Zostera bed habitat definitions, clearly documenting the evidence behind the assessments and any differences between assessments. Nineteen pressures, falling in five categories - biological, hydrological, physical damage, physical loss, and pollution and other chemical changes - were assessed in this report. Assessments were based on the three British seagrasses Zostera marina, Z. noltei and Ruppia maritima. Z. marina var. angustifolia was considered to be a subspecies of Z. marina but it was specified where studies had considered it as a species in its own rights. Where possible other components of the community were investigated but the basis of the assessment focused on seagrass species. To develop each sensitivity assessment, the resistance and resilience of the key elements were assessed against the pressure benchmark using the available evidence. The benchmarks were designed to provide a ‘standard’ level of pressure against which to assess sensitivity. Overall, seagrass beds were highly sensitive to a number of human activities: • penetration or disturbance of the substratum below the surface; • habitat structure changes – removal of substratum; • physical change to another sediment type; • physical loss of habitat; • siltation rate changes including and smothering; and • changes in suspended solids. High sensitivity was recorded for pressures which directly impacted the factors that limit seagrass growth and health such as light availability. Physical pressures that caused mechanical modification of the sediment, and hence damage to roots and leaves, also resulted in high sensitivity. Seagrass beds were assessed as ‘not sensitive’ to microbial pathogens or ‘removal of target species’. These assessments were based on the benchmarks used. Z. marina is known to be sensitive to Labyrinthula zosterae but this was not included in the benchmark used. Similarly, ‘removal of target species’ addresses only the biological effects of removal and not the physical effects of the process used. For example, seagrass beds are probably not sensitive to the removal of scallops found within the bed but are highly sensitive to the effects of dredging for scallops, as assessed under the pressure penetration or disturbance of the substratum below the surface‘. This is also an example of a synergistic effect Assessing the sensitivity of seagrass bed biotopes to pressures associated with marine activities between pressures. Where possible, synergistic effects were highlighted but synergistic and cumulative effects are outside the scope off this study. The report found that no distinct differences in sensitivity exist between the HPI, PMF and OSPAR definitions. Individual biotopes do however have different sensitivities to pressures. These differences were determined by the species affected, the position of the habitat on the shore and the sediment type. For instance evidence showed that beds growing in soft and muddy sand were more vulnerable to physical damage than beds on harder, more compact substratum. Temporal effects can also influence the sensitivity of seagrass beds. On a seasonal time frame, physical damage to roots and leaves occurring in the reproductive season (summer months) will have a greater impact than damage in winter. On a daily basis, the tidal regime could accentuate or attenuate the effects of pressures depending on high and low tide. A variety of factors must therefore be taken into account in order to assess the sensitivity of a particular seagrass habitat at any location. No clear difference in resilience was established across the three seagrass definitions assessed in this report. The resilience of seagrass beds and the ability to recover from human induced pressures is a combination of the environmental conditions of the site, growth rates of the seagrass, the frequency and the intensity of the disturbance. This highlights the importance of considering the species affected as well as the ecology of the seagrass bed, the environmental conditions and the types and nature of activities giving rise to the pressure and the effects of that pressure. For example, pressures that result in sediment modification (e.g. pitting or erosion), sediment change or removal, prolong recovery. Therefore, the resilience of each biotope and habitat definitions is discussed for each pressure. Using a clearly documented, evidence based approach to create sensitivity assessments allows the assessment and any subsequent decision making or management plans to be readily communicated, transparent and justifiable. The assessments can be replicated and updated where new evidence becomes available ensuring the longevity of the sensitivity assessment tool. The evidence review has reduced the uncertainty around assessments previously undertaken in the MB0102 project (Tillin et al 2010) by assigning a single sensitivity score to the pressures as opposed to a range. Finally, as seagrass habitats may also contribute to ecosystem function and the delivery of ecosystem services, understanding the sensitivity of these biotopes may also support assessment and management in regard to these. Whatever objective measures are applied to data to assess sensitivity, the final sensitivity assessment is indicative. The evidence, the benchmarks, the confidence in the assessments and the limitations of the process, require a sense-check by experienced marine ecologists before the outcome is used in management decisions.

Assessing the sensitivity of Sabellaria spinulosa to pressures associated with marine activities.

The Joint Nature Conservation Committee (JNCC) commissioned this project to generate an improved understanding of the sensitivities of Sabellaria spinulosa reefs based on the OSPAR habitat definition. This work aimed to provide an evidence base to facilitate and support management advice for Marine Protected Areas, development of UK marine monitoring and assessment, and conservation advice to offshore marine industries. The OSPAR list of threatened and declining species and habitats refers to subtidal S. spinulosa reefs on hard or mixed substratum. S. spinulosa may also occur as thin crusts or individual worms but these are not the focus of conservation. The purpose of this project was to produce sensitivity assessments with supporting evidence for S. spinulosa reefs, clearly documenting the evidence behind the assessments and the confidence in these assessments. Sixteen pressures, falling in five categories - biological, hydrological, physical damage, physical loss, and pollution and other chemical changes - were assessed in this report. To develop each sensitivity assessment, the resistance and resilience of the key elements of the habitat were assessed against the pressure benchmark using the available evidence. The benchmarks were designed to provide a ‘standard’ level of pressure against which to assess sensitivity. The highest sensitivity (‘medium’) was recorded for physical pressures which directly impact the reefs including: • habitat structure changes – removal of substratum; • abrasion and penetration and sub-surface disturbance; • physical loss of habitat and change to habitat; and • siltation rate changes including and smothering. The report found that no evidence for differences in the sensitivity of the three EUNIS S. spinulosa biotopes that comprise the OSPAR definition. However, this evidence review has identified significant information gaps regarding sensitivity, ecological interactions with other species and resilience. No clear difference in resilience was established across the OSPAR S. spinulosa biotopes that were assessed in this report. Using a clearly documented, evidence based approach to create sensitivity assessments allows the assessment and any subsequent decision making or management plans to be readily communicated, transparent and justifiable. The assessments can be replicated and updated where new evidence becomes available ensuring the longevity of the sensitivity assessment tool. Finally, as S. spinulosa habitats may also contribute to ecosystem function and the delivery of ecosystem services, understanding the sensitivity of these biotopes may also support assessment and management in regard to these. Whatever objective measures are applied to data to assess sensitivity, the final sensitivity assessment is indicative. The evidence, the benchmarks, the confidence in the assessments and the limitations of the process, require a sense-check by experienced marine ecologists before the outcome is used in management decisions.