Influence of carbide particles on the dynamic recrystallization of as-cast 304 stainless steel: a study using secondary ion mass spectrometric (SIMS) analysis

The domain of dynamic recrystallization (DRX) in as-cast 304 stainless steel material occurs at higher temperatures (1250 degrees C) and lower strain rates (0.001 s(-1)) than in wrought 304 stainless steel (1100 degrees C and 0.01 s(-1)). The above result has been explained earlier on the basis of a simple theoretical DRX model involving the rate of nucleation versus rate of grain boundary migration. The present investigation is aimed at examining experimentally the influence of carbide particles on the DRX of ascast 304 using secondary ion mass spectrometric (SIMS) analysis. Isothermal compression tests at a constant true strain rate have been performed on wrought 304 and as-cast 304 materials in the temperature and strain rate ranges of 1000 to 1250 degrees C and 0.001 to 1 s(-1) respectively. The SIMS analysis carried out on the deformed samples revealed that the large carbides present in the as-cast 304 material strongly influence the DRX process. In as-cast 304 material, the presence of large carbide particles in the microstructure shifts the DRX domain to higher temperature and lower strain rate in comparison with wrought 304 material.

Instability map for cold and warm working of as-cast 304 stainless steel

The deformation characteristics of as-cast 304 stainless steel under compression in the temperature range 20-600 degrees C and strain rate range 0.001-100 s(-1) have been studied with a view to characterizing the flow instabilities occurring in the microstructure. Ar strain rates of less than 0.05 s(-1), as-cast 304 stainless steel exhibits flow localization in the temperature range 20-600 degrees C, whereas dynamic strain ageing occurs at intermediate temperatures and below 5 s(-1). At room temperatures and strain rates of less than 0.05 s(-1), martensite formation is observed. To avoid the above microstructural instabilities warm working should be carried out at strain rates greater than 10 s(-1) in the temperature range 400-600 degrees C and cold working could be done in the range of about 0.05-0.8 s(-1). The continuum criterion developed on the basis of the principles of maximum rate of entropy production and separability of the dissipation function, predicts accurately all of the above instability features. (C) 1997 Elsevier Science S.A.

Tensile flow behaviour of 2.25Cr-1Mo ferritic steel base metal and simulated heat affected zone structures of 2.25Cr-1Mo weld joint

Tensile tests in the temperature range 298 to 873 K have been performed on 2.25Cr-1Mo base metal and simulated heat affected zone (HAZ) structures of its weld joint, namely coarse grain bainite, fine grain bainite and intercritical structure. Tensile flow behaviour of all the microstructural conditions could be adequately described by the Hollomon equation (sigma = K-1 epsilon(n1)) at higher (> 623 K) temperatures. Deviation from the Hollomon equation was observed at low strains and lower (< 623 K) temperatures. The Ludwigson modification of Hollomon's equation, sigma = K-1 epsilon(n1) + exp (K-2 + n(2) epsilon), was found to describe the flow curve. In general, the flow parameters n(1), K-1, n(2) and K-2 were found to decrease with increase in temperature except in the intermediate temperature range (423 to 623 K). Peaks/plateaus were observed in their variation with temperature in the intermediate temperature range coinciding with the occurrence of serrated flow in the load-elongation curve. The n(1) Value increased and the K-1 value decreased with the type of microstructure in the order: coarse grain bainite, fine grain bainite, base metal and intercritical structure. The variation of nl with microstructure has been rationalized on the basis of mean free path (MFP) of dislocations which is directly related to the inter-particle spacing. Larger MFP of dislocations lead to higher strain hardening exponents n(1).

An assessment of creep deformation and fracture behavior of 2.25Cr-1Mo similar and dissimilar weld joints

The evaluation of the creep deformation and fracture behavior of a 2.25Cr-1Mo steel base metal, a 2.25Cr-1Mo/2.25Cr-1Mo similar weld joint, and a 2.25Cr-1Mo/Alloy 800 dissimilar weld joint at 823 K over a stress range of 90 to WO MPa has been carried out. The specimens for creep testing were taken from single-V weld pads fabricated by a shielded metal arc-welding process using 2.25Cr-1Mo steel (for similar-joint) and INCONEL 182 (for dissimilar-joint) electrodes. The weld pads were subsequently given a postweld hear treatment (PWHT) of 973 K for I hour. The microstructure and microhardness of the weld joints were evaluated in the as-welded, postweld heat-treated, and creep-tested conditions. The heat-affected zone (HAZ) of similar weld joint consisted of bainite in the coarse-prior-austenitic-grain (CPAG) region near the fusion line, followed by bainite in the fine-prior-austenitic-grain (FPAG) and intercritical regions merging with the unaffected base metal. In addition to the HAZ structures in the 2.25Cr-1Mo steel, the dissimilar weld joint displayed a definite INCONEL/2.25Cr-1Mo weld interface structure present either as a sharp line or as a diffuse region. A hardness trough was observed in the intercritical region of the HAZ in both weld joints, while a maxima in hardness was seen at the weld interface of the dissimilar weld joint. Both weld joints exhibited significantly lower rupture lives compared to the 2.25Cr-1Mo base metal. The dissimilar weld joint exhibited poor rupture life compared to the similar weld joint, at applied stresses lower than 130 MPa. In both weld joints, the strain distribution across the specimen gage length during creep testing varied significantly. During creep testing, localization of deformation occurred in the intercritical HAZ. In the similar weld joint, at all stress levels investigated, and in the dissimilar weld joint, at stresses greater than or equal to 150 MPa, the creep failure occulted in the intercritical HAZ. The fracture occurred by transgranular mode with a large number of dimples. At stresses below 150 MPa, the failure in the dissimilar weld joint occurred in the CPAG HAZ near to the weld interface. The failure occurred by extensive intergranular creep cavity formation.

An assessment of creep deformation and fracture behavior of 2.25Cr-1Mo

The evaluation of the creep deformation and fracture behavior of a 2.25Cr-1Mo steel base metal, a 2.25Cr-1Mo/2.25Cr-1Mo similar weld joint, and a 2.25Cr-1Mo/Alloy 800 dissimilar weld joint at 823 K over a stress range of 90 to WO MPa has been carried out. The specimens for creep testing were taken from single-V weld pads fabricated by a shielded metal arc-welding process using 2.25Cr-1Mo steel (for similar-joint) and INCONEL 182 (for dissimilar-joint) electrodes. The weld pads were subsequently given a postweld hear treatment (PWHT) of 973 K for I hour. The microstructure and microhardness of the weld joints were evaluated in the as-welded, postweld heat-treated, and creep-tested conditions. The heat-affected zone (HAZ) of similar weld joint consisted of bainite in the coarse-prior-austenitic-grain (CPAG) region near the fusion line, followed by bainite in the fine-prior-austenitic-grain (FPAG) and intercritical regions merging with the unaffected base metal. In addition to the HAZ structures in the 2.25Cr-1Mo steel, the dissimilar weld joint displayed a definite INCONEL/2.25Cr-1Mo weld interface structure present either as a sharp line or as a diffuse region. A hardness trough was observed in the intercritical region of the HAZ in both weld joints, while a maxima in hardness was seen at the weld interface of the dissimilar weld joint. Both weld joints exhibited significantly lower rupture lives compared to the 2.25Cr-1Mo base metal. The dissimilar weld joint exhibited poor rupture life compared to the similar weld joint, at applied stresses lower than 130 MPa. In both weld joints, the strain distribution across the specimen gage length during creep testing varied significantly. During creep testing, localization of deformation occurred in the intercritical HAZ. In the similar weld joint, at all stress levels investigated, and in the dissimilar weld joint, at stresses greater than or equal to 150 MPa, the creep failure occulted in the intercritical HAZ. The fracture occurred by transgranular mode with a large number of dimples. At stresses below 150 MPa, the failure in the dissimilar weld joint occurred in the CPAG HAZ near to the weld interface. The failure occurred by extensive intergranular creep cavity formation.

Validation of processing maps for a 15Cr-15Ni-2.2Mo-0.3Ti austenitic stainless steel using hot forging and rolling tests

The processing maps are being developed for use in optimising hot workability and controlling the microstructure of the product. The present investigation deals with the examination to assess the prediction of the processing maps for a 15Cr-15Ni-2.2Mo-0.3Ti austenitic stainless steel using forging and rolling tests at different temperatures in the range of 600-1200 degreesC. The tensile properties of these deformed products were evaluated at room temperature. The influence of the processing conditions, i.e. strain rate and temperature on the tensile properties of the deformed product were analysed to identify the optimum processing parameters. The results have shown good agreement between the regimes exhibited by the map and the properties of the rolled or forged product. The optimum parameters for processing of this steel were identified as rolling or press forging at temperatures above 1050 degreesC to obtain optimum product properties. (C) 2002 Elsevier Science B.V. All rights reserved.

UDP-glucose 4, 6-dehydratase Activity Plays an Important Role in Maintaining Cell Wall Integrity and Virulence of Candida albicans

Candida albicans, a human fungal pathogen, undergoes morphogenetic changes that are associated with virulence. We report here that GAL102 in C. albicans encodes a homolog of dTDP-glucose 4,6-dehydratase, an enzyme that affects cell wall properties as well as virulence of many pathogenic bacteria. We found that GAL102 deletion leads to greater sensitivity to antifungal drugs and cell wall destabilizing agents like Calcofluor white and Congo red. The mutant also formed biofilms consisting mainly of hyphal cells that show less turgor. The NMR analysis of cell wall mannans of gal102 deletion strain revealed that a major constituent of mannan is missing and the phosphomannan component known to affect virulence is greatly reduced. We also observed that there was a substantial reduction in the expression of genes involved in biofilm formation but increase in the expression of genes encoding glycosylphosphatidylinositol-anchored proteins in the mutant. These, along with altered mannosylation of cell wall proteins together might be responsible for multiple phenotypes displayed by the mutant. Finally, the mutant was unable to grow in the presence of resident peritoneal macrophages and elicited a weak pro-inflammatory cytokine response in vitro. Similarly, this mutant elicited a poor serum pro-inflammatory cytokine response as judged by IFN gamma and TNF alpha levels and showed reduced virulence in a mouse model of systemic candidiasis. Importantly, an Ala substitution for a conserved Lys residue in the active site motif YXXXK, that abrogates the enzyme activity also showed reduced virulence and increased filamentation similar to the gal102 deletion strain. Since inactivating the enzyme encoded by GAL102 makes the cells sensitive to antifungal drugs and reduces its virulence, it can serve as a potential drug target in combination therapies for C. albicans and related pathogens.

Effects of periphyton grown on bamboo substrates on growth and production of Indian major carp, rohu (Label rohita Ham.)

The effects of periphyton, grown on bamboo substrates, on growth and production of Indian major carp, rohu, Labeo rohita (Hamilton), were studied in 10 ponds during July to October '95 at the Bangladesh Agricultural University, Mymensingh. Five ponds were provided with bamboo substrates (treatment I) and the rests without bamboo substrates (treatment II). It was revealed that there had been no discernible difference in the water quality parameters between treatments. A large number of plankton (30 genera) showed periphytic nature and colonized on the bamboo substrates. The growth and production of fish was significantly (p<0.05) higher in the ponds with bamboo substrates as compared to the ponds without substrates. The net production of rohu in treatment I was about 1.7 times higher than that of treatment II. Fish production was as much as 1899 kg/ha over a culture period of 4 months in the periphyton-based production system.

四种方法对鲢血清免疫球蛋白的纯化及分子量测定

采用mannan-binding protein(MBP)、TG及免疫亲和层析法和饱和硫酸铵沉淀法纯化鲢血清免疫球蛋白IgM,并比较了4种纯化方法的纯化效果.SDS-PAGE显示鲢血清免疫球蛋白的重链和轻链分子量分别为76.4 kD和27.2 kD,推算其总分子量约828.8kD.

An ancient C-type lectin in Chlamys farreri (CfLec-2) that mediate pathogen recognition and cellular adhesion

C-type lectins are a superfamily of Ca2+ dependent carbohydrate-recognition proteins which play significant diverse roles in nonself-recognition and clearance of invaders. In the present study, a C-type lectin (CfLec-2) from Zhikong scallop Chlamys farreri was selected to investigate its functions in innate immunity. The mRNA expression of CfLec-2 in hemocytes was significantly up-regulated (P < 0.01) after scallops were stimulated by LPS. PGN or beta-glucan, and reached the highest expression level at 12h post-stimulation, which was 72.5-, 23.6- or 43.8-fold compared with blank group, respectively. The recombinant Cflec-2 (designated as rCfLec-2) could bind LPS, PGN, mannan and zymosan in vitro, but it could not bind beta-glucan. Immunofluorescence assay with polyclonal antibody specific for Cflec-2 revealed that CfLec-2 was mainly located in the mantle, kidney and gonad. Furthermore, rCfLec-2 could bind to the surface of scallop hemocytes, and then initiated cellular adhesion and recruited hemocytes to enhance their encapsulation in vitro, and this process could be specifically blocked by anti-rCfLec-2 serum. These results collectively suggested that CfLec-2 from the primitive deuterostome C. farreri could perform two distinct immune functions, pathogen recognition and cellular adhesion synchronously, while these functions were performed by collectins and selectins in vertebrates, respectively. The synchronous functions of pathogen recognition and cellular adhesion performed by CfLec-2 tempted us to suspect that CfLec-2 was an ancient form of C-type lectin, and apparently the differentiation of these two functions mediated by C-type lectins occurred after mollusk in phylogeny. (C) 2010 Elsevier Ltd. All rights reserved.

Structural characterization and biological activity of polysaccharides from infusions used in the popular tradition

The use of plants with medicinal purposes is an ancient practice still very common in developing regions, and is rapidly spreading in industrialized countries. This fact is evidenced by the large number of ethnobotanical studies found in the literature referring that these plants are often used as decoctions and infusions. In most studies the reported biological activities are attributed to the presence of phenolic compounds, due to their antioxidant properties, and to polysaccharides, with its anti-tumoral properties. In “Trás-os-Montes” region, some of the most popular infusions used by the popular medicine are prepared with the dried leaves of Fraxinus angustifolia, the dried shoots of Mentha suaveolens, and the dried inflorescences of Pterospartum tridentatum. However, there are no studies about the polysaccharides present in these infusions. Thus, through the structural characterization of the polysaccharides present in the infusions of F. angustifolia, M. suaveolens, and P. tridentatum, the present PhD thesis intends to evaluate the possible relation between polysaccharides and the immunostimulatory activity that these infusions might present. In a preliminary phase, infusions of F. angustifolia were prepared according to the popular tradition, and it was observed that the obtained water soluble material contained approximately 85% of material non-retained in C18 cartridges, with hydrophilic characteristics, with the remaining 15% comprising retained-material with hydrophobic characteristics. It was also shown that the infusions only contained between 2 and 4% of high molecular weight material (HMWM), which comprised approximately 30% of carbohydrate material. Sugar and methylation analysis of the HMWM suggested the presence of pectic polysaccharides, together with type II arabinogalactans, mannans, and xyloglucans. However, the amount of material obtained is to low for the fractionation, and structural analysis of the polysaccharides present. The 4 h decoction, divided in two periods of 2 h, with water renewal, allowed to increase the HMWM yield, relatively to the infusions traditional infusions. It was also observed that the decoction also allowed to increase the HMWM proportion of carbohydrate material, due to an increase in the proportion of uronic acid present, although the neutral sugar residues seemed to be detected in similar proportions. Therefore, in all the experiments subsequently performed, the HMWM used was obtained through the decoction of F. angustifolia dried leaves, M. suaveolens dried shoots, and P. tridentatum dried inflorescences. x After the fractionation, through ethanol precipitation, and anion exchange chromatography, of the polysaccharides from the HMWM obtained by the decoction of the vegetable material of the distinct studied plants, it was observed the presence of high proportions of pectic polysaccharides, containing type I arabinogalactans, together with minor proportions of type II arabinogalactans, mannans, and xyloglucans. The presence of pectic polysaccharides in the extracts from F. angustifolia was also evidenced through endo-polygalacturonase treatment, and ESI-MS and ESI-MS/MS experiments. The detection of linked pentose and uronic acid residues, also seemed to suggest the presence of xylogalacturonan domains in the pectic polysaccharides from F. angustifolia. The extracts from F. angustifolia dried leaves also contained type II arabinogalactans that exhibited a higher structural diversity than those detected in the M. suaveolens, and P. tridentatum extracts, particularly in the substitution degree of the galactan backbone, and in the extension of the (1→5)-Araf side chains. Moreover, for all the plants studied, it was also observed that the type II arabinogalactans, extracted during the 2nd 2h of the extraction process, exhibited a substitution degree of the galactan backbone higher than those extracted during the 1st 2h. The extracts from P. tridentatum dried inflorescences contained higher proportions of mannans, and also of xyloglucans, both presenting a substitution degree higher than those, which were detected in lower proportion in the extracts of F. angustifolia and M. suaveolens. Through ESI-MS and ESI-MS/MS it was possible to evidence that the mannans present in the extracts of P. tridentatum presented acetyl groups on the O-2 of the mannosyl residues. It was also evidenced that the P. tridentatum mannans were more extensively acetylated than the mannans detected in the coffee infusion, LBG, and other non-conventional mannan sources. Moreover, it was detected the presence of oligosaccharides comprising hexose residues linked to non acetylated pentose residues, suggesting the possible presence of arabinose residues in the mannans from P. tridentatum extracts. The immunostimulatory activity of three fractions isolated from the extracts of F. angustifolia, M. suaveolens, and P. tridentatum, was tested and an increase in the NO production by macrophages, without compromising their cellular viability, was observed. The type I, and type II arabinogalactans detected in the extracts from F. angustifolia, and M. suaveolens seem to have contributed for the observed immunostimulatory activity. For the fraction from P. tridentatum, the mannans acetylation, and the presence of type I, and type II arabinogalactans seemed to contribute for the macrophage immunostimulatory activity observed. The possible presence of storage xyloglucans from the inflorescences seeds, also seems to have contributed for the immunostimulatory activity registered when the macrophages were stimulated with higher extract concentrations. The results obtained allow to conclude that the extracts of F. angustifolia dried leaves, M. suaveolens dried shoots, and P. tridentatum dried inflorescences contained high proportions of pectic polysaccharides, exhibiting type I arabinogalactans, together with other polysaccharides, such as type II arabinogalactans, mannans, and xyloglucans. This polysaccharide mixture seems to have contributed to the immunostimulatory activity of fractions isolated from the extracts of the studied plants. Therefore, as the same type of polysaccharides seem to be present in the decoctions and in the infusions, it seems possible that the polysaccharides might contribute for the therapeutic properties frequently associated by the popular tradition to the infusions of these plants.

Qualidade de vida das famílias apoiadas por intervenção precoce: identificação de fatores mais valorizados pelas famílias

Dissertação apresentada à Escola Superior de Educação de Lisboa para obtenção do grau de mestre em Intervenção Precoce

Rôles physiopathologiques du complément dans le syndrome coronarien aigu et implications thérapeutiques

Les efforts investis pour diminuer les risques de développer un infarctus du myocarde sont nombreux. Aujourd’hui les médecins prennent connaissance des divers facteurs de risque connus prédisposant aux syndromes coronariens aigus (SCA) dans le but de prendre en charge les patients «à risque» [1]. Bien que le suivi rigoureux et le contrôle de certains facteurs de risque modifiables aient permis une meilleure gestion des cas de SCA, les cas d’infarctus persistent de manière encore trop fréquente dans le monde. Puisque d’importantes études ont démontré que les SCA pouvaient survenir sans même la présence des facteurs de risque conventionnels [2, 3], les chercheurs se sont penchés sur un autre mécanisme potentiellement responsable de l’avènement des SCA : l’inflammation. L’inflammation joue un rôle prépondérant dans l’initiation, la progression et les complications de l’athérosclérose [4, 5] mais aussi dans les situations post-infarctus [6, 7]. Au cours des dernières années, le contrôle du processus inflammatoire est devenu une cible de choix dans la prévention et le traitement des SCA. Cependant, malgré les efforts investis, aucun de ces traitements ne s’est avéré pleinement efficace dans l’atteinte du but ultime visé par une diminution de l’inflammation : la diminution de la mortalité. Le complément est un système complexe reconnu principalement pour son rôle primordial dans l’immunité [2]. Cependant, lorsqu’il est activé de manière inappropriée ou excessive, il peut être à l’origine de nombreux dommages cellulaires caractéristiques de plusieurs pathologies inflammatoires dont font partie les complications de l’athérosclérose et des événements post-infarctus. Le travail effectué dans le cadre de mon doctorat vise à établir les rôles physiopathologiques du complément dans les interactions de l’axe thrombose-inflammation caractéristiques des SCA dans le but ultime d’identifier des cibles thérapeutiques permettant le développement de nouvelles approches pour la prévention et le traitement de ces pathologies. Les principaux résultats obtenus durant mon cursus suggèrent d’abord que la voie alterne du complément peut représenter une cible thérapeutique de choix dans les maladies coronariennes aiguës puisque l’activation terminale du complément semble y être principalement causée par l’activation du cette voie. De faibles niveaux sériques de MBL (mannan-binding lectin) et une activation terminale négligeable du complément caractérisent plutôt la maladie coronarienne stable. En comparant l’activité relative de chacune des voies du complément chez des cohortes de patients traités ou non par un anticorps spécifique à la protéine C5 du complément (pexelizumab), un second volet démontre quant à lui qu’une inhibition de l’activation du C5 n’a pas d’effet bénéfique majeur sur l’inhibition de la formation du complexe sC5b-9 ou sur les événements cliniques subséquents. Par conséquent, nous avons exploré, à l’aide d’un modèle in vitro, les raisons de l’inefficacité du traitement. Les résultats révèlent que le blocage du C5 avec le pexelizumab inhibe la production de l’anaphylatoxine pro-inflammatoire C5a et du complexe terminal du complément sans toutefois avoir d’effet sur l’apoptose des cellules endothéliales produites induite par le sérum des patients atteints de STEMI. Finalement, une autre section stipule que l’atorvastatine diminue l’activation du complément induite par les plaquettes sanguines chez des patients hypercholestérolémiques, mettant en évidence l’importance du rôle de cette statine dans la réduction des effets délétères de l’activation du système du complément médié par les plaquettes. Ensemble, l’étude du rôle spécifique des différentes voies d’activation du complément dans des contextes pathologiques variés, l’analyse des effets d’une inhibition spécifique de la protéine C5 du complément dans la progression des SCA et la mise en évidence des interactions entre l’activation du complément et les plaquettes activées ont contribué au développement d’une meilleure connaissance des rôles physiopathologiques du complément dans la progression de la maladie coronarienne.