Laboratory determination of coefficient of consolidation from pore water pressure measurement

In the recent past, many studies have been carried out on the determination of coefficient of consolidation (c(v)) from the time (t)-deformation (d) data obtained from conventional consolidation tests. Several researchers have also proposed different curve fitting procedures for determining cv from the t-d data. It is anticipated that the cv values obtained from the t-d data may be influenced by initial and secondary compressions. Nevertheless, the pore water pressure data measured during the consolidation process will be independent of initial and secondary compressions. In this study, the conventional Asaoka (1978) method is extended to evaluate cv and end-of-primary (EOP) consolidation from the pore water pressure data measured from laboratory experiments. Laboratory experiments were carried out on the modified one-dimensional consolidation apparatus on different remoulded clay samples measuring pore water pressure during the consolidation process. The cv and EOP computed from the proposed approach have been compared with the results of the t-d data and found to be in good agreement.

Capacity approaching codes for non-coherent orthogonal modulation

This paper describes a curve-fitting approach for the design of capacity approaching coded modulation for orthogonal signal sets with non-coherent detection. In particular, bit-interleaved coded modulation with iterative decoding is considered. Decoder metrics are developed that do not require knowledge of the signal-to-noise ratio, yet still offer very good performance. © 2007 IEEE.

Damage Evolution In Cement Mortar Due To Erosion Of Sulphate

Ultrasonic technique is used to detect the velocity change of stress wave propagated in the cement mortar immersed in the solution of sodium sulfate for 425 days. Also the density change of specimens at different erosion time is measured. By curve fitting, the effect of solutions' concentration and water/cement ratio on the damage evolution is analyzed. The SEM observation on the growth of delayed ettringite is also performed. It shows that the damage evolution of specimens attacked by sulphate solution is dominantly induced by the nucleation and growth of delayed ettringite, and the average size of microvoids in cement mortar affects the damage evolution significantly. (c) 2008 Elsevier Ltd. All rights reserved.

Measuring Binding Kinetics Of Surface-Bound Molecules Using The Surface Plasmon Resonance Technique

Surface plasmon resonance (SPR) technology and the Biacore biosensor have been widely used to measure the kinetics of biomolecular interactions in the fluid phase. In the past decade, the assay was further extended to measure reaction kinetics when two counterpart molecules are anchored on apposed surfaces. However, the cell binding kinetics has not been well quantified. Here we report development of a cellular kinetic model, combined with experimental procedures for cell binding kinetic measurements, to predict kinetic rates per cell. Human red blood cells coated with bovine serum albumin and anti-BSA monoclonal antibodies (mAbs) immobilized on the chip were used to conduct the measurements. Sensor-grams for BSA-coated RBC binding onto and debinding from the anti-BSA mAb-immobilized chip were obtained using a commercial Biacore 3000 biosensor, and analyzed with the cellular kinetic model developed. Not only did the model fit the data well, but it also predicted cellular on and off-rates as well as binding affinities from curve fitting. The dependence of flow duration, flow rate, and site density of BSA on binding kinetics was tested systematically, which further validated the feasibility and reliability of the new approach. Crown copyright (c) 2008 Published by Elsevier Inc. All rights reserved.

Avaliação de proposições matemáticas para interpretação do comportamento de solos residuais não saturados

Nas últimas décadas, teorias têm sido formuladas para interpretar o comportamento de solos não saturados e estas têm se mostrado coerentes com resultados experimentais. Paralelamente, várias técnicas de campo e de laboratório têm sido desenvolvidas. No entanto, a determinação experimental dos parâmetros dos solos não saturados é cara, morosa, exige equipamentos especiais e técnicos experientes. Como resultado, essas teorias têm aplicação limitada a pesquisas acadêmicas e são pouco utilizados na prática da engenharia. Para superar este problema, vários pesquisadores propuseram equações para representar matematicamente o comportamento de solos não saturados. Estas proposições são baseadas em índices físicos, caracterização do solo, em ensaios convencionais ou simplesmente em ajustes de curvas. A relação entre a umidade e a sucção matricial, convencionalmente denominada curva característica de sucção do solo (SWCC) é também uma ferramenta útil na previsão do comportamento de engenharia de solos não saturados. Existem muitas equações para representar matematicamente a SWCC. Algumas são baseadas no pressuposto de que sua forma está diretamente relacionada com a distribuição dos poros e, portanto, com a granulometria. Nestas proposições, os parâmetros são calibrados pelo ajuste da curva de dados experimentais. Outros métodos supõem que a curva pode ser estimada diretamente a partir de propriedades físicas dos solos. Estas propostas são simples e conveniente para a utilização prática, mas são substancialmente incorretas, uma vez que ignoram a influência do teor de umidade, nível de tensões, estrutura do solo e mineralogia. Como resultado, a maioria tem sucesso limitado, dependendo do tipo de solo. Algumas tentativas têm sido feitas para prever a variação da resistência ao cisalhamento com relação a sucção matricial. Estes procedimentos usam, como uma ferramenta, direta ou indiretamente, a SWCC em conjunto com os parâmetros efetivos de resistência c e . Este trabalho discute a aplicabilidade de três equações para previsão da SWCC (Gardner, 1958; van Genuchten, 1980; Fredlund; Xing, 1994) para vinte e quatro amostras de solos residuais brasileiros. A adequação do uso da curva característica normalizada, proposta por Camapum de Carvalho e Leroueil (2004), também foi investigada. Os parâmetros dos modelos foram determinados por ajuste de curva, utilizando técnicas de problema inverso; dois métodos foram usados: algoritmo genético (AG) e Levenberq-Marquardt. Vários parâmetros que influênciam o comportamento da SWCC são discutidos. A relação entre a sucção matricial e resistência ao cisalhamento foi avaliada através de ajuste de curva utilizando as equações propostas por Öberg (1995); Sällfors (1997), Vanapalli et al., (1996), Vilar (2007); Futai (2002); oito resultados experimentais foram analisados. Os vários parâmetros que influênciam a forma da SWCC e a parcela não saturadas da resistência ao cisalhamento são discutidos.

Caracterización a impacto de caucho reciclado mediante elementos finitos

Análisis de caucho reciclado de manera hiperelástica mediante métodos de ajuste de Mínimos Cuadrados con programa MATLAB y Curve fitting mediante ANSYS. Para la parte viscoelástica se usa Algoritmo de Optimicación con MATLAB. Comprobación de resultados y fiabilidad.

A note on the von Bertalanffy growth function concerning the allocation of surplus energy to reproduction

We propose an extended form of the von Bertalanffy growth function (VBGF), where the allocation of surplus energy to reproduction is considered. Any function can be used in our model to describe the ratio of energy allocation for reproduction to that for somatic growth. As an example, two models for energy allocation were derived: a step-function and a logistic function. The extended model can jointly describe growth in adult and juvenile stages. The change in growth rate between the two stages can be either gradual or steep; the latter gives a biphasic VBGF. The results of curve fitting indicated that a consideration of reproductive energy is meaningful for model extension. By controlling parameter values, our comprehensive model gives various growth curve shapes ranging from indeterminate to determinate growth. An increase in the number of parameters is unavoidable in practical applications of this new model. Additional information on reproduction will improve the reliability of model estimates.

The modelling of soil plasticity

The modeling of the soil plasticity was discussed and it was shown that the grain breakage is an important factor of the plastic soil behaviour. A reduction of internal coefficient of friction was observed when stress-level was increased. The yield paths of all stress path tests determined by curve fitting were presented.

Fem modeling of periodic arrays of multi-walled carbon nanotubes

Multiwalled carbon nanotubes display dielectric properties similar to those of graphite, which can be calculated using the well known Drude-Lorentz model. However, most computational softwares lack the capacity to directly incorporate this model into the simulations. We present the finite element modeling of optical propagation through periodic arrays of multiwalled carbon nanotubes. The dielectric function of nanotubes was incorporated into the model by using polynomial curve fitting technique. The computational analysis revealed interesting metamaterial filtering effects displayed by the highly dense square lattice arrays of carbon nanotubes, having lattice constants of the order few hundred nanometers. The curve fitting results for the dielectric function can also be used for simulating other interesting optical applications based on nanotube arrays.

Stiffness of sands through a laboratory test database

Deformations of sandy soils around geotechnical structures generally involve strains in the range small (0·01%) to medium (0·5%). In this strain range the soil exhibits non-linear stress-strain behaviour, which should be incorporated in any deformation analysis. In order to capture the possible variability in the non-linear behaviour of various sands, a database was constructed including the secant shear modulus degradation curves of 454 tests from the literature. By obtaining a unique S-shaped curve of shear modulus degradation, a modified hyperbolic relationship was fitted. The three curve-fitting parameters are: an elastic threshold strain γe, up to which the elastic shear modulus is effectively constant at G0; a reference strain γr, defined as the shear strain at which the secant modulus has reduced to 0·5G0; and a curvature parameter a, which controls the rate of modulus reduction. The two characteristic strains γe and γr were found to vary with sand type (i.e. uniformity coefficient), soil state (i.e. void ratio, relative density) and mean effective stress. The new empirical expression for shear modulus reduction G/G0 is shown to make predictions that are accurate within a factor of 1·13 for one standard deviation of random error, as determined from 3860 data points. The initial elastic shear modulus, G0, should always be measured if possible, but a new empirical relation is shown to provide estimates within a factor of 1·6 for one standard deviation of random error, as determined from 379 tests. The new expressions for non-linear deformation are easy to apply in practice, and should be useful in the analysis of geotechnical structures under static loading.

Extraction of intrinsic frequency response of p-i-n photodiodes

This letter presents a new method for extracting the intrinsic frequency response of a p-i-n photodiode (PD) from the measured frequency response of the PD at different bias voltages. This method is much simpler than the conventional calibration method, since only the measured scattering parameters are required, and there is no need to calibrate the test fixtures and the lightwave source. Experiment shows that the proposed method is as accurate as the calibration method.

Extraction of intrinsic response from S-parameters of laser diodes

We describe a new method for extracting the intrinsic response of a laser diode from S-parameters measured using a calibrated vector network analyzer. The experimental results obtained using the new method are compared with those obtained using the optical modulation method and the frequency response subtraction method. Good agreement has been obtained, confirming the new method validity and accuracy. The new method has the advantages of obtaining the intrinsic characteristics of a laser diode with conventional measurements using a network analyzer.

Sputtering induced by Arq+ impact on Nb surface

The relative sputtering yield induced by highly charged Arq+ impacting on Nb surface is investigated. The yield increases drastically as the incidence angle increases. A formula Y=A* tan(B) (theta) + C, developed from classical sputtering theory, fits well with the yield. By analysing a series of coefficients A and C extracted by curve fitting, the results demonstrate the presence of a synergy of the linear cascade collision and potential energy deposition.

Observation of a Possible New Isomer in Ir-175

The neutron deficient nuclide Ir-175 was produced by irradiation of Nd-146 with 210 MeV Cl-35 via a fusion-evaporation reaction channel. The reaction products were transported to a low-background location using a helium-jet recoil fast-moving tape-transport system for measurement. The experimental devices and data analysis method are introduced. Based on the decay-curve fitting of the beta-delayed gamma ray from Ir-175, realized by the least-square method, a new long-lived isomeric state of Ir-175 is proposed and briefly discussed.