Effects of pCO2 and iron on the elemental composition and cell geometry of the marine diatom Pseudo-nitzschia pseudodelicatissima//(Bacillariophyceae)

Partial pressure of CO2 (pCO2) and iron availability in seawater show corresponding changes due to biological and anthropogenic activities. The simultaneous change in these factors precludes an understanding of their independent effects on the ecophysiology of phytoplankton. In addition, there is a lack of data regarding the interactive effects of these factors on phytoplankton cellular stoichiometry, which is a key driving factor for the biogeochemical cycling of oceanic nutrients. Here, we investigated the effects of pCO2 and iron availability on the elemental composition (C, N, P, and Si) of the diatom Pseudo-nitzschia pseudodelicatissima (Hasle) Hasle by dilute batch cultures under 4 pCO2 (~200, ~380, ~600, and ~800 µatm) and five dissolved inorganic iron (Fe'; ~5, ~10, ~20, ~50, and ~100 pmol /L) conditions. Our experimental procedure successfully overcame the problems associated with simultaneous changes in pCO2 and Fe' by independently manipulating carbonate chemistry and iron speciation, which allowed us to evaluate the individual effects of pCO2 and iron availability. We found that the C:N ratio decreased significantly only with an increase in Fe', whereas the C:P ratio increased significantly only with an increase in pCO2. Both Si:C and Si:N ratios decreased with increasing pCO2 and Fe'. Our results indicate that changes in pCO2 and iron availability could influence the biogeochemical cycling of nutrients in future oceans with high- CO2 levels, and, similarly, during the time course of phytoplankton blooms. Moreover, pCO2 and iron availability may also have affected oceanic nutrient biogeochemistry in the past, as these conditions have changed markedly over the Earth's history.

Seawater carbonate chemistry and toxicity of Pseudo-nitzschia fraudulenta in a laboratory experiment

Anthropogenic CO2 is progressively acidifying the ocean, but the responses of harmful algal bloom species that produce toxins that can bioaccumulate remain virtually unknown. The neurotoxin domoic acid is produced by the globally-distributed diatom genus Pseudo-nitzschia. This toxin is responsible for amnesic shellfish poisoning, which can result in illness or death in humans and regularly causes mass mortalities of marine mammals and birds. Domoic acid production by Pseudo-nitzschia cells is known to be regulated by nutrient availability, but potential interactions with increasing seawater CO2 concentrations are poorly understood. Here we present experiments measuring domoic acid production by acclimatized cultures of Pseudo-nitzschia fraudulenta that demonstrate a strong synergism between projected future CO2 levels (765 ppm) and silicate-limited growth, which greatly increases cellular toxicity relative to growth under modern atmospheric (360 ppm) or pre-industrial (200 ppm) CO2 conditions. Cellular Si:C ratios decrease with increasing CO2, in a trend opposite to that seen for domoic acid production. The coastal California upwelling system where this species was isolated currently exhibits rapidly increasing levels of anthropogenic acidification, as well as widespread episodic silicate limitation of diatom growth. Our results suggest that the current ecosystem and human health impacts of toxic Pseudo-nitzschia blooms could be greatly exacerbated by future ocean acidification and 'carbon fertilization' of the coastal ocean.

Diatoms and laminae of Mediterranean sapropels

The origins of sapropels (sedimentary layers rich in organic carbon) are unclear, yet they may be a key to understanding the influence of climate on ocean eutrophication, the mechanisms of sustaining biological production in stratified waters and the genesis of petroleum source rocks (Rohling, 1994, doi:10.1016/0025-3227(94)90202-X; Castradori, 1993, doi:10.1029/93PA00756; Calvert et al., 1992, doi:10.1038/359223a0). Recent microfossil studies of foraminifera (Rohling, 1994, doi:10.1016/0025-3227(94)90202-X) and calcareous nannofossils (Castradori, 1993, doi:10.1029/93PA00756) have focused attention on a deep chlorophyll maximum as a locus for the high production inferred (Calvert et al., 1992, doi:10.1038/359223a0) for sapropel formation, but have not identified the agent responsible. Here we report the results of a high-resolution, electron-microscope-based study of a late Quaternary laminated sapropel in which the annual flux cycle has been preserved. We find that much of the production was by diatoms, both mat-forming and other colonial forms, adapted to exploit a deep nutrient supply trapped below surface waters in a stratified water column. Reconstructed organic-carbon and opal fluxes to the sediments are comparable to those at high-productivity sites in today's oceans, and calculations based on diatom Si/C ratios suggest that the high organic-carbon content of sapropels may be entirely accounted for by sedimenting diatoms. We propose that this style of production may have been common in ancient Palaeogene and Cretaceous seas, environments for which conventional appeals to upwelling-driven production to account for the occurrence of diatomites, and some organic-carbon-rich sediments, have never seemed wholly appropriate.

The beta effect in alkylsilanes

It was suggested to us that compounds of the type XCH2SiR2CH2CH2Y might show interesting chemical and biological activity due to them possessing both an alpha group and a beta group. The aim of this research was to discover whether or not the alpha and beta effects interact with each other, and if so whether interaction is via steric or electronic effects. A series of compounds were made with a constant chloromethyl alpha function and varying beta functions (hydroxy, methoxy and chloro groups); plus a second series of trimethylsilyl substituted silanes with the same variety of beta functions were synthesised. The stereochemistry of the products was investigated by analysis of NMR spectra and of dipole moment data. It was found that the β-chloro-substituted compounds possessed restricted rotation. The methoxy- and hydroxy-substituted compounds which displayed more or less simple triplets, appear to possess free rotation; the smaller sized hydroxy and methoxy groups seemingly no great barrier to rotation. Similarly, compounds possessing larger alpha alkyl groups appeared also to possess restricted rotation, it was concluded that for the compounds possessing large alpha or a large beta function steric effects dominate. The kinetics of the solvolysis reaction were studied. β-functional alkylsilanes commonly undergo solvolysis by unimolecular elimination at remarkably enhanced rates. The β-hydroxy- and β-methoxy-substituted chloroethyl derivatives reacted substantially slower that their trimethylsilyl analogues, due to the electronegative chlorine pulling electrons into the Si-C bond. For compounds possessing an electronegative substituent alpha to silicon it seems it is the electronic effects that act to inhibit the beta effect. 2-Chloroethylchloromethyldimethylsilane initially appeared not to react solvolytically, however NMR analysis of the solvolysis products indicated that a reaction did occur but by an as yet unknown mechanism. For compounds with an a α-electronegative substituent in conjunction with a large β-function it was concluded both steric and electronic effects are important.

Advanced Analytical Microscopy at the Nanoscale: Applications in Wide Bandgap and Solid Oxide Fuel Cell Materials

The atomic-level structure and chemistry of materials ultimately dictate their observed macroscopic properties and behavior. As such, an intimate understanding of these characteristics allows for better materials engineering and improvements in the resulting devices. In our work, two material systems were investigated using advanced electron and ion microscopy techniques, relating the measured nanoscale traits to overall device performance. First, transmission electron microscopy and electron energy loss spectroscopy (TEM-EELS) were used to analyze interfacial states at the semiconductor/oxide interface in wide bandgap SiC microelectronics. This interface contains defects that significantly diminish SiC device performance, and their fundamental nature remains generally unresolved. The impacts of various microfabrication techniques were explored, examining both current commercial and next-generation processing strategies. In further investigations, machine learning techniques were applied to the EELS data, revealing previously hidden Si, C, and O bonding states at the interface, which help explain the origins of mobility enhancement in SiC devices. Finally, the impacts of SiC bias temperature stressing on the interfacial region were explored. In the second system, focused ion beam/scanning electron microscopy (FIB/SEM) was used to reconstruct 3D models of solid oxide fuel cell (SOFC) cathodes. Since the specific degradation mechanisms of SOFC cathodes are poorly understood, FIB/SEM and TEM were used to analyze and quantify changes in the microstructure during performance degradation. Novel strategies for microstructure calculation from FIB-nanotomography data were developed and applied to LSM-YSZ and LSCF-GDC composite cathodes, aged with environmental contaminants to promote degradation. In LSM-YSZ, migration of both La and Mn cations to the grain boundaries of YSZ was observed using TEM-EELS. Few substantial changes however, were observed in the overall microstructure of the cells, correlating with a lack of performance degradation induced by the H2O. Using similar strategies, a series of LSCF-GDC cathodes were analyzed, aged in H2O, CO2, and Cr-vapor environments. FIB/SEM observation revealed considerable formation of secondary phases within these cathodes, and quantifiable modifications of the microstructure. In particular, Cr-poisoning was observed to cause substantial byproduct formation, which was correlated with drastic reductions in cell performance.

A comparative study of the structural, mechanical and tribological characteristics of TiSiC-Cr coatings prepared in CH4 and C2H2 reactive atmosphere by cathodic vacuum arc

TiSiC-Cr coatings, with Cr and Si as additional elements, were deposited on Si, C 45 and 316 L steel substrates via cathodic arc evaporation. Two series of coatings with thicknesses in the range of 3.6–3.9 μm were produced, using either CH4 or C2H2 as carbon containing gas. For each series, different coatings were prepared by varying the carbon rich gas flow rate between 90 and 130 sccm, while maintaining constant cathode currents (110 and 100 A at TiSi and Cr cathodes, respectively), substrate bias (–200 V) and substrate temperature (∼320 °C). The coatings were analyzed for their mechanical characteristics (hardness, adhesion) and tribological performance (friction, wear), along with their elemental and phase composition, chemical bonds, crystalline structure and cross-sectional morphology. The coatings were found to be formed with nano-scale composite structures consisting of carbide crystallites (grain size of 3.1–8.2 nm) and amorphous hydrogenated carbon. The experimental results showed significant differences between the two coating series, where the films formed from C2H2 exhibited markedly superior characteristics in terms of microstructure, morphology, hardness, friction behaviour and wear resistance. For the coatings prepared using CH4, the measured values of crystallite size, hardness, friction coefficient and wear rate were in the ranges of 7.2–8.2 nm, 26–30 GPa, 0.3–0.4 and 2.1–4.8 × 10−6 mm3 N−1 m−1, respectively, while for the coatings grown in C2H2, the values of these characteristics were found to be in the ranges of 3.1–3.7 nm, 41–45 GPa, 0.1–0.2 and 1.4–3.0 × 10−6 mm3 N−1 m−1, respectively. Among the investigated coatings, the one produced using C2H2 at the highest flow rate (130 sccm) exhibited the highest hardness (45.1 GPa), the lowest friction coefficient (0.10) and the best wear resistance (wear rate of 1.4 × 10−6 mm3 N−1 m−1).

Silicon nanocrystals tailored for bioimaging and energy conversion

This thesis focus is the development of hybrid organic-inorganic systems based on Silicon Nanocrystals (SiNCs) with possible applications in the field of bioimaging and solar energy conversion. SiNCs were engineered thanks to the realization of a strong covalent Si-C bond on their surface, which allowed us to disperse them in different solvents with different final purpose. Chapter 1 introduces the basic properties of nanomaterials. Chapter 2 describes all the synthetic procedures to obtain the organic molecules-functionalized SiNCs. Chapter 3 illustrates an organic-inorganic antenna system based on SiNCs conjugated with diphenylanthracene (DPA) photoactive molecules, which was also embedded into Luminescent Solar Concentrators (LSC) made of a polymeric matrix. The optical and photovoltaic performances of this device were compared with the ones of a LSC embedded with a physical mixture made of SiNCs plus DPA at the same concentrations of the two components in the covalent system. Chapter 4 shows many different techniques to functionalize SiNCs with polyethylene glycol (PEG) chains in order to make them dispersible in water, for biomedical imaging applications. Chapter 5 presents the synthesis of dyes and/or SiNCs loaded Polymer Nanoparticles (PNPs) capable of excitation energy transfer (EET) mechanism. Chapter 6 is focused on the realization of photo-switchable systems based on azobenzene derivatives-functionalized SiNCs. These organic-inorganic hybrid materials were studied to possibly obtain a new light-driven response of SiNCs. In the end, chapter 7 reports the activity I followed in America, at The University of Texas at Austin, in the laboratory led by the professor Brian Korgel. Here I studied and compared the properties of high temperature hydrosilylated SiNCs and room temperature, radical promoted, hydrosilylated SiNCs.

Isothermal Section of the V-Si-B System at 1600 A degrees C in the V-VSi(2)-VB Region

In recent years, the Me-Si-B (Me-metal) ternary systems have received considerable attention aiming at the development of high-temperature structural materials. Assuming that any real application of these materials will rely on multicomponent alloys, as is the case of Ni-base superalloys, phase equilibria data of these systems become very important. In this work, results are reported on phase equilibria in the V-Si-B system, and are summarized in the form of an isothermal section at 1600 A degrees C for the V-VSi(2)-VB region. Several alloys of different compositions were prepared via arc melting and then heat-treated at 1600 A degrees C under high vacuum. All the materials in both as-cast and heat-treated conditions were characterized through x-ray diffraction, scanning electron microscopy, and selected alloys via wavelength dispersive spectroscopy. A negligible solubility of B in the V(3)Si, V(5)Si(3) (T(1)), and V(6)Si(5) phases as well as of Si in V(3)B(2) and VB phases was noted. Two ternary phases presenting the structures known as T(2) (Cr(5)B(3)-prototype) and D8(8) (Mn(5)Si(3)-prototype) were observed in both as-cast and heat-treated samples. It is proposed that at 1600 A degrees C the homogeneity range of T(2) extends approximately from 5 at.% to 12 at.% Si at constant vanadium content and the composition of D8(8) phase is close to V(59.5)Si(33)B(7.5) (at.%).

A 3-phase model for VIS/NIR mu C-Si : H p-i-n detectors

The spectral response and the photocurrent delivered by entirely microcrystalline p-i-n-Si:H detectors an analysed under different applied bias and light illumination conditions. The spectral response and the internal collection depend not only on the energy range but also on the illumination side. Under [p]- and [n]-side irradiation, the internal collection characteristics have an atypical shape. It is high for applied bias and lower than the open circuit voltage, shows a steep decrease near the open circuit voltage (higher under [n]-side illumination) and levels off for higher voltages. Additionally, the numerical modeling of the VIS/NIR detector, based on the band discontinuities near the grain boundaries and interfaces, complements the study and gives insight into the internal physical process.

Optoelectronic properties of a-Si(1-x)C(x)H films grown in hydrogen diluted silane-methane plasma

This work reports on the optoelectronic properties and device application of hydrogenated amorphous silicon carbide (a-Si(1-x)C(x):H) films grown by plasma-enhanced chemical vapour deposition (PECVD). The films with an optical bandgap ranging from about 1.8 to 2.0 eV were deposited in hydrogen diluted silane-methane plasma by varying the radio frequency power. Several n-i-p structures with an intrinsic a-Si(1-x)C(x):H layer of different optical gaps were also fabricated. The optimized devices exhibited a diode ideality factor of 1.4-1.8, and a leakage current of 190-470 pA/cm(2) at -5 V. The density of deep defect states in a-Si(1-x)C(x):H was estimated from the transient dark current measurements and correlated with the optical bandgap and carbon content. Urbach energies for the valence band tail were also determined by analyzing the spectral response within sub-bandgap energy range. (C) 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Polymerabgeleitete Keramiken im System Si-O-C(-N)-Ta

Magdeburg, Univ., Fak. für Maschinenbau, Diss., 2013

Efecto de los contenidos de C, Mn y Si en el comportamiento a fluencia en caliente de aceros de construcción al carbono y microaleados: aplicación a la obtención de grano ultrafino en productos largos laminados

Després d’aplicar alguns tractaments d’elaboració i conservació als aliments, queden bacteris lesionats. Aquests bacteris perden la capacitat de créixer en els medis de cultiu selectiu convencionals, de manera que se’n subestima el recompte. Malgrat això, poden recuperar-se als aliments i suposar un risc per la salut, ja que alguns encara poden mantenir activitat metabòlica i integritat estructural. En aquest projecte, es van optimitzar protocols de preparació de mostres per citometria de flux (CF) per avaluar l’estat fisiològic de patògens alimentaris (Escherichia coli O157:H7, Salmonella Enteritidis i Listeria monocytogenes) sotmesos a estrès. Es van estudiar principalment dos paràmetres fisiològics: la integritat de membrana, mitjançant iodur de propidi i fluorocroms de la família SYTO; i l’activitat respiratòria, per la reducció intracel•lular d’una sal de tetrazole, el CTC. En primer lloc, es van avaluar variables de protocol, com la concentració de colorant, la ràtio entre colorants, la solució de tinció i el temps d’incubació, en mostres control (cèl•lules sanes i mortes). A continuació, els protocols optimitzats es van aplicar a suspensions bacterianes en medi de cultiu que prèviament havien estat sotmeses a estressos físics i fisicoquímics. Durant l’etapa final del projecte, els coneixements adquirits sobre la preparació de mostres per CF es van aplicar a l’anàlisi de mostres de matriu complexa: amanides comercials inoculades amb E. coli O157:H7. Als assajos amb indicadors d’integritat de membrana en suspensions bacterianes sotmeses a estrès, es van poder quantificar cèl•lules amb la membrana parcialment danyada (presumptes cèl•lules lesionades). El recompte de cèl•lules que mantingueren l’activitat respiratòria després de ser sotmeses a estrès va ser superior al que es va obtenir mitjançant recompte en placa convencional, cosa que va evidenciar la presència de cèl•lules actives però no cultivables. La introducció d’estratègies per reduir les interferències provocades per les partícules alimentàries i l’ús d’un anticòs amb marcatge fluorescent va permetre detectar selectivament les cèl•lules d’E. coli O157:H7 i avaluar-ne la integritat de membrana simultàniament. L’anàlisi de cèl•lules bacterianes per CF requereix de la exhaustiva optimització dels protocols, que són específics per cada soca i matriu. Malgrat això, i a diferència del mètode convencional per recompte en placa, ofereix la possibilitat d’obtenir una gran quantitat d’informació sobre el sovint complex estat fisiològic d’una mostra.

White luminescence from Si+ and C+ ion-implanted SiO2 films

The microstructural and optical analysis of SiO2 layers emitting white luminescence is reported. These structures have been synthesized by sequential Si+ and C+ ion implantation and high-temperature annealing. Their white emission results from the presence of up to three bands in the photoluminescence (PL) spectra, covering the whole visible spectral range. The microstructural characterization reveals the presence of a complex multilayer structure: Si nanocrystals are only observed outside the main C-implanted peak region, with a lower density closer to the surface, being also smaller in size. This lack of uniformity in their density has been related to the inhibiting role of C in their growth dynamics. These nanocrystals are responsible for the band appearing in the red region of the PL spectrum. The analysis of the thermal evolution of the red PL band and its behavior after hydrogenation shows that carbon implantation also prevents the formation of well passivated Si/SiO2 interfaces. On the other hand, the PL bands appearing at higher energies show the existence of two different characteristics as a function of the implanted dose. For excess atomic concentrations below or equal to 10%, the spectra show a PL band in the blue region. At higher doses, two bands dominate the green¿blue spectral region. The evolution of these bands with the implanted dose and annealing time suggests that they are related to the formation of carbon-rich precipitates in the implanted region. Moreover, PL versus depth measurements provide a direct correlation of the green band with the carbon-implanted profile. These PL bands have been assigned to two distinct amorphous phases, with a composition close to elemental graphitic carbon or stoichiometric SiC.

Progress in a-Si:H/c-Si heterojunction emitters obtained by Hot-Wire CVD at 200°C

In this work, we investigate heterojunction emitters deposited by Hot-Wire CVD on p-type crystalline silicon. The emitter structure consists of an n-doped film (20 nm) combined with a thin intrinsic hydrogenated amorphous silicon buffer layer (5 nm). The microstructure of these films has been studied by spectroscopic ellipsometry in the UV-visible range. These measurements reveal that the microstructure of the n-doped film is strongly influenced by the amorphous silicon buffer. The Quasy-Steady-State Photoconductance (QSS-PC) technique allows us to estimate implicit open-circuit voltages near 700 mV for heterojunction emitters on p-type (0.8 Ω·cm) FZ silicon wafers. Finally, 1 cm 2 heterojunction solar cells with 15.4% conversion efficiencies (total area) have been fabricated on flat p-type (14 Ω·cm) CZ silicon wafers with aluminum back-surface-field contact.

Surface passivation and optical characterization of Al2O3/a-SiCx stacks on c-Si substrates

Postprint (published version)