Cationic ring opening polymerisation (CROP) of oxetane and its derivatives using oxonium derived initiators

Several cationic initiator systems were developed and used to polymerise oxetane with two oxonium ion initiator systems being investigated in depth. The first initiator system was generated by the elimination of a chloride group from a chloro methyl ethyl ether. Adding a carbonyl co-catalyst to a carbocationic centre generated the second initiator system. It was found that the anion used to stabilise the initiator was critical to the initial rate of polymerisation of oxetane with hexafluoroantimonate resulting in the fastest polymerisations. Both initiator systems could be used at varying monomer to initiator concentrations to control the molecular number average, Mn, of the resultant polymer. Both initiator systems showed living characteristics and were used to polymerise further monomers and generate higher molecular weight material and block copolymers. Oxetane and 3,3-dimethyl oxetane can both be polymerised using either oxonium ion initiator system in a variety of DCM or DCM/1,4-dioxane solvent mixtures. The level of 1,4-dioxane does have an impact on the initial rate of polymerisation with higher levels resulting in lower initial rates of polymerisation but do tend to result in higher polydispersities. The level of oligomer formation is also reduced as the level of 1,4-dioxane is increased. 3,3-bis-bromomethyl oxetane was also polymerised but a large amount of hyperbranching was seen at the bromide site resulting in a difficult to solvate polymer system. Multifunctional initiator systems were also generated using the halide elimination reactions with some success being achieved with 1,3,5-tris-bromomethyl-2,4,6-tris-methyl-benzene derived initiator system. This offered some control over the molecular number average of the resultant polymer system.

Catalyst studies on the ring opening of tetrahydrofuran-dimethanol to 1,2,6-hexanetriol

The metal catalyzed hydrogenolysis of the biomass-derived THF-dimethanol to 1,2,6-hexanetriol using heterogeneous catalysts was investigated. Bimetallic Rh-Re catalysts (4 wt% Rh and a Re/Rh (mol. ratio of 0.5) on a silica support gave the best performance and 1,2,6-hexanetriol was obtained in 84% selectivity at 31% conversion (120 C, 80 bar, 4 h); the selectivity reaches a maximum of 92% at 80 C. The product distribution at prolonged reaction times or higher temperatures or both shows the formation of diols and mono-alcohols, indicating that the 1,2,6-hexanetriol is prone to subsequent hydrodeoxygenation reactions. Different silica supports were investigated and optimal results were obtained with an amorphous silica featuring an intermediate surface area and an average mesopore size of about 6 nm. TPR and XPS surface analysis support the presence of mixed Rh and Re particles. The redox Reδ+/ReTotal surface ratio correlates with the conversion in a volcano type dependency. Both gas phase as well as Rh200Re1OH cluster DFT calculations support an acid-metal bifunctional mechanism and explain the products distribution. © 2013 Elsevier B.V. All rights reserved.

Thermal properties of amphiphilic biodegradable triblock copolymer of l,l-lactide and ethylene glycol

Samples of poly(l,l-lactide)-block-poly(ethylene glycol)-block-poly(l,l-lactide) (PLLA-PEG-PLLA) were synthesized from l,l-lactide polymerization using stannous 2-ethylhexanoate, Sn(Oct)(2) as initiator and di-hydroxy-terminated poly(ethylene glycol) (PEG) (M (n) = 4000 g mol(-1)) as co-initiator. The chemical linkage between the PEG segment and the PLA segments was characterized by Fourier transform infrared spectroscopy (FTIR). Thermogravimetry analysis (TG) revealed the copolymers composition and was capable to show the deleterious effect of an excess of Sn(Oct)(2) in the polymer thermal stability, while Differential Scanning Calorimetry (DSC) allowed the observation of the miscibility between the PLLA and PEG segments in the different copolymers.

Improved polymeric medical devices for active substances delivery

The work presented in this thesis was developed in collaboration with a Portuguese company, BeyonDevices, devoted to pharmaceutical packaging, medical technology and device industry. Specifically, the composition impact and surface modification of two polymeric medical devices from the company were studied: inhalers and vaginal applicators. The polyethylene-based vaginal applicator was modified using supercritical fluid technology to acquire self-cleaning properties and prevent the transport of bacteria and yeasts to vaginal flora. For that, in-situ polymerization of 2-substituted oxazolines was performed within the polyethylene matrix using supercritical carbon dioxide. The cationic ring-opening polymerization process was followed by end-capping with N,N-dimethyldodecylamine. Furthermore, for the same propose, the polyethylene matrix was impregnated with lavender oil in supercritical medium. The obtained materials were characterized physical and morphologically and the antimicrobial activity against bacteria and yeasts was accessed. Materials modified using 2-substituted oxazolines showed an effective killing ability for all the tested microorganisms, while the materials modified with lavender oil did not show antimicrobial activity. Only materials modified with oligo(2-ethyl-2-oxazoline) maintain the activity during the long term stability. Furthermore, the cytotoxicity of the materials was tested, confirming their biocompatibilty. Regarding the inhaler, its surface was modified in order to improve powder flowability and consequently, to reduce powder retention in the inhaler´s nozzle. New dry powder inhalers (DPIs), with different needle’s diameters, were evaluated in terms of internal resistance and uniformity of the emitted dose. It was observed that they present a mean resistance of 0.06 cmH2O0.5/(L/min) and the maximum emitted dose obtained was 68.9% for the inhaler with higher needle´s diameter (2 mm). Thus, this inhaler was used as a test and modified by the coating with a commonly-used force control agent, magnesium stearate, dried with supercritical carbon dioxide (scCO2) and the uniformity of delivered dose tests were repeated. The modified inhaler showed an increase in emitted dose from 68.9% to 71.3% for lactose and from 30.0% to 33.7% for Foradil.

Green synthesis of 2-Oxazoline-based polymers with antimicrobial activity using scCO2

Using a green methodology, 17 different poly(2-oxazolines) were synthesized starting from four different oxazoline monomers. The polymerization reactions were conducted in supercritical carbon dioxide under a cationic ring-opening polymerization (CROP) mechanism using boron trifluoride diethyl etherate as the catalyst. The obtained living polymers were then end-capped with different types of amines, in order to confer them antimicrobial activity. For comparison, four polyoxazolines were end-capped with water, and by their hydrolysis the linear poly(ethyleneimine) (LPEI) was also produced. After functionalization the obtained polymers were isolated, purified and characterized by standard techniques (FT-IR, NMR, MALDI-TOF and GPC). The synthesized poly(2-oxazolines) revealed an unusual intrinsic blue photoluminescence. High concentration of carbonyl groups in the polymer backbone is appointed as a key structural factor for the presence of fluorescence and enlarges polyoxazolines’ potential applications. Microbiological assays were also performed in order to evaluate their antimicrobial profile against gram-positive Staphylococcus aureus NCTC8325-4 and gram-negative Escherichia coli AB1157 strains, two well known and difficult to control pathogens. The minimum inhibitory concentrations (MIC)s and killing rates of three synthesized polymers against both strains were determined. The end-capping with N,N-dimethyldodecylamine of living poly(2- methyl-2-oxazoline) and poly(bisoxazoline) led to materials with higher MIC values but fast killing rates (less than 5 minutes to achieve 100% killing for both bacterial species) than LPEI, a polymer which had a lower MIC value, but took a longer time to kill both E.coli and S.aureus cells. LPEI achieved 100% killing after 45 minutes in contact with E. coli and after 4 hours in contact with S.aureus. Such huge differences in the biocidal behavior of the different polymers can possibly underlie different mechanisms of action. In the future, studies to elucidate the obtained data will be performed to better understand the killing mechanisms of the polymers through the use of microbial cell biology techniques.

Modification of commercial poly-lactide for extrusion coated food packaging applications

Poly-L-lactide (PLLA) is a widely used sustainable and biodegradable alternative to replace synthetic non-degradable plastic materials in the packaging industry. Conversely, its processing properties are not always optimal, e.g. insufficient melt strength at higher temperatures (necessary in extrusion coating processes). This thesis reports on research to improve properties of commercial PLLA grade (3051D from NatureWorks), to satisfy and extend end-use applications, such as food packaging by blending with modified PLLA. Adjustment of the processability by chain branching of commercial poly-L-lactide initiated by peroxide was evaluated. Several well-defined branched structures with four arms (sPLLA) were synthesized using pentaerythritol as a tetra-functional initiator. Finally, several block copolymers consisting of polyethylene glycol and PLLA (i.e. PEGLA) were produced to obtain a well extruded material with improved heat sealing properties. Reactive extrusion of poly-L-lactide was carried out in the presence of 0.1, 0.3 and 0.5 wt% of various peroxides [tert-butyl-peroxybenzoate (TBPB), 2,5-dimethyl-2,5-(tert-butylperoxy)-hexane (Lupersol 101; LOL1) and benzoyl peroxide (BPO)] at 190C. The peroxide-treated PLLAs showed increased complex viscosity and storage modulus at lower frequencies, indicating the formation of branched/cross linked architectures. The material property changes were dependent on the peroxide, and the used peroxide concentration. Gel fraction analysis showed that the peroxides, afforded different gel contents, and especially 0.5 wt% peroxide, produced both an extremely high molar mass, and a cross linked structure, not perhaps well suited for e.g. further use in a blending step. The thermal behavior was somewhat unexpected as the materials prepared with 0.5 wt% peroxide showed the highest ability for crystallization and cold crystallization, despite substantial cross linking. The peroxide-modified PLLA, i.e. PLLA melt extruded with 0.3 wt% of TBPB and LOL1 and 0.5 wt% BPO was added to linear PLLA in ratios of 5, 15 and 30 wt%. All blends showed increased zero shear viscosity, elastic nature (storage modulus) and shear sensitivity. All blends remained amorphous, though the ability of annealing was improved slightly. Extrusion coating on paperboard was conducted with PLLA, and peroxide-modified PLLA blends (90:10). All blends were processable, but only PLLA with 0.3 wt% of LOL1 afforded a smooth high quality surface with improved line speed. Adhesion levels between fiber and plastic, as well as heat seal performance were marginally reduced compared with pure 3051D. The water vapor transmission measurements (WVTR) of the blends containing LOL1 showed acceptable levels, only slightly lower than for comparable PLLA 3051D. A series of four-arm star-shaped poly-L-lactide (sPLLA) with different branch length was synthesized by ring opening polymerization (ROP) of L-lactide using pentaerythritol as initiator and stannous octoate as catalyst. The star-shaped polymers were further blended with its linear resin and studied for their melt flow and thermal properties. Blends containing 30 wt% of sPLLA with low molecular weight (30 wt%; Mwtotal: 2500 g mol-1 and 15000 g mol-1) showed lower zero shear viscosity and significantly increased shear thinning, while at the same time slightly increased crystallization of the blend. However, the amount of crystallization increased significantly with the higher molecular weight sPLLA, therefore the star-shaped structure may play a role as nucleating agent. PLLA-polyethylene glycol–PLLA triblock copolymers (PEGLA) with different PLLA block length were synthesized and their applicability as blends with linear PLLA (3051D NatureWorks) was investigated with the intention of improving heat-seal and adhesion properties of extrusion-coated paperboard. PLLA-PEG-PLLA was obtained by ring opening polymerization (ROP) of L-lactide using PEG (molecular weight 6000 g mol-1) as an initiator, and stannous octoate as catalyst. The structures of the PEGLAs were characterized by proton nuclear magnetic resonance spectroscopy (1H-NMR). The melt flow and thermal properties of all PEGLAs and their blends were evaluated using dynamic rheology, and differential scanning calorimeter (DSC). All blends containing 30 wt% of PEGLAs showed slightly higher zero shear viscosity, higher shear thinning and increased melt elasticity (based on tan delta). Nevertheless, no significant changes in thermal properties were distinguished. High molecular weight PEGLAs were used in extrusion coating line with 3051D without problems.

Photophysical and Electrochemical Investigations on Photoconducting Poly(6-tert-butyl-3,4-dihydro-2H- 1,3-benzoxazine)

Poly(6-tert-butyl-3,4-dihydro-2H-1,3-benzoxazine) was synthesized by thermally activated cationic ring opening polymerization. The structure of the polymer was confirmed by spectral and thermal studies. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) were estimated using cyclic voltammetry and optical absorption. Modulated photocurrent measurement technique was employed to study the spectral and field dependence of photocurrent. Photocurrent of the order of 1.5 micro A/m2 was obtained for polymer at a biasing electric field of 40 V/mico m.

Effect of sequence distribution on the morphology, crystallization, melting, and biodegradation of poly(epsilon-caprolactone-co-epsilon-caprolactam) copolymers

Two types of poly(epsilon-caprolactone (CLo)-co-poly(epsilon-caprolactam (CLa)) copolymers were prepared by catalyzed hydrolytic ring-opening polymerization. Both cyclic comonomers were added simultaneously in the reaction medium for the First type or materials where copolymers have a random distribution of counits, as evidenced by H-1 and C-13 NMR. For the second type of copolymers, the cyclic comonomers were added sequentially, yielding diblock poly(ester-amides). The materials were characterized by differential scanning calorimetry (DSC), wide- and small-angle X-ray scattering (WAXS and SAXS), and transmission and scanning electron microscopies (TEM and SEM). Their biodegradation in compost was also studied. All copolymers were found to be miscible by the absence of structure in the melt. TEM revealed that all samples exhibited a crystalline lamellar morphology. DSC and WAXS showed that in a wide composition range (CLo contents from 6 to 55%) only the CLa units were capable of crystallization in the random copolymers. The block copolymer samples only experience a small reduction of crystallization and melting temperature with composition, and this was attributed to a dilution effect caused by the miscible noncrystalline CLo units. The comparison between block and random copolymers provided a unique opportunity to distinguish the dilution effect of the CLo units on the crystallization and melting of the polyamide phase from the chemical composition effect in the random copolymers case, where the CLa sequences are interrupted statistically by the CLo units, making the crystallization of the polyamide strongly composition dependent. Finally, the enzymatic degradation of the copolymers in composted soil indicate a synergistic behavior where much faster degradation was obtained for random copolymers witha CLo content larger than 30% than for neat PCL.

Nonspherical assemblies generated from polystyrene-b-poly(L-lysine) polyelectrolyte block copolymers

This report describes the aqueous solution self-assembly of a series of polystyrene(m)-b-poly(L-lysine)n block copolymers (m = 8-10; n = 10-70). The polymers are prepared by ring-opening polymerization of epsilon-benzyloxycarbonyl-L-lysine N-carboxyanhydride using amine terminated polystyrene macroinitiators, followed by removal of the benzyloxycarbonyl side chain protecting groups. The critical micelle concentration of the block copolymers determined using the pyrene probe technique shows a parabolic dependence on peptide block length exhibiting a maximum at n = approximately 20 (m = 8) or n = approximately 60 (m = 10). The shape and size of the aggregates has been studied by dynamic and static light scattering, small-angle neutron scattering (SANS), and analytical ultracentrifugation (AUC). Surprisingly, Holtzer and Kratky analysis of the static light scattering results indicates the presence of nonspherical, presumably cylindrical objects independent of the poly(L-lysine)n block length. This is supported by SANS data, which can be fitted well by assuming cylindrical scattering objects. AUC analysis allows the molecular weight of the aggregates to be estimated as several million g/mol, corresponding to aggregation numbers of several 10s to 100s. These aggregation numbers agree with those that can be estimated from the length and diameter of the cylinders obtained from the scattering results.

Aluminium- und Yttrium-Initiatoren für die koordinative Ringöffnungspolymerisation von Propylenoxid

Zielsetzung ist der synthetische Zugang zu metallorganischen Verbindungen, die Propylenoxid koordinativ polymerisieren und deren Aktivität sich durch gezielte Variation der sterischen oder elektronischen Eigenschaften kontrollieren läßt. Zur Bearbeitung dieser Aufgabe werden zwei verschiedene Klassen von Komplexen synthetisiert und charakterisiert: Vorwiegend durch Salzmetathese werden mehrere Yttriumamide der allgemeinen Formel Y(NRR´)3(THF)x erhalten. Dabei erfolgt eine Diskussion der Auswirkungen sterischer und elektronischer Variation der beiden Amido-Substituenten R und R´, die sich in der Bildung von „at“-Komplexen, Lösungsmitteladdukten und größeren Aggregaten äußern. Durch Alkaneliminierung wird eine umfassende Reihe von Aluminiumkomplexen methylen- und thioverbrückter Bisphenolatoliganden dargestellt. Die Verbindungen besitzen unter Ausschluß zusätzlicher Basen dimere oder mehrkernige Strukturen, deren Diskussion schwerpunktsmäßig anhand ihres Verhaltens in Lösung erfolgt. Die Aluminiumkomplexe werden in anschließenden Reaktionen zu Lösungsmitteladdukten und Aluminaten umgesetzt.Die Yttriumamide initiieren die Ringöffnungspolymerisation von Propylenoxid bei Temperaturen von 60 oder 80 °C. Die Polymerisation erfolgt nach einem koordinativen Mechanismus, eine zu niedrige Katalysatoreffizienz schließt jedoch die Yttriumamide als Vorläufer zu definierten „single site“-Katalysatoren aus. Mit der Kombination aus neutralen Aluminiumkomplexen mit den entsprechenden Aluminaten verläuft die Ringöffnungspolymerisation von Propylenoxid bei Raumtemperatur schnell und kontrolliert. Es läßt sich ein prinzipiell neuer Mechanismus belegen, bei dem die Polymerisation unter synergistischer Wirkung eines Aluminiumphenolato-Komplexes mit dem korrespondierenden „at“-Komplex erfolgt.

Helix-coil-transition in solid polypeptides

Abstract Poly(L-glutamic acid) (PLGA) was synthesized by living anionic ring-opening polymerization of the NCA monomer, which was obtained by reacting diphosgene with an amino acid derivative. The chemical structures and thermal properties were characterized by 1H-NMR, 13C-NMR, TGA and DSC. XRD powder patterns found to be amorphous for all polymers obtained. The molecular weights could be determined under severe limitations due to low solubility and high aggregation tendency. The secondary structure of the PLGA films was analyzed in the solid state by IR spectroscopy; the order was determined mainly by XRD. Uniform bulk films (1-5 µm) were produced by drop-casting of PLGA solutions in TFA on silica. The XRD film analysis indicated the absence of a long range order or an orientation even if a helical microstructure was confirmed by IR spectroscopy. The coil solvent TFA delivered constantly a helical or a β-sheet structure in the solid state depending on the water content of the solvent which was observed for the first time to exhibit a high influence on the crystallization process for PLGA. Temperature dependent in-situ IR measurements were examined to analyze if a helix-coil transition occurs, but there could be no solvent system determined, which resulted in a disordered coil structure in the solid state. General parameters like solvent systems, evaporation conditions, concentration, substrates etc. were analyzed. New crystallizations were obtained on silica prepared by drop-casting of solutions of PLGA in DMF, DMA, TMU, NMP, and pyridine/water mixtures, respectively. PSCBC in DMF, CDCl3/TFA-d, and PSBC in CDCl3/TFA-d exhibited the same crystalline diffraction patterns like PLGA. The long range order in the X-ray diffraction pattern is proven by extremely sharp crystalline signals, which are not changing the shape or the position of the peak by increasing the temperature up to 160°C. The substrate seems to play a decisive role because the crystalline structures were not obtainable on glass. The crystal structure consists probably of two different layered structures based on the intensity ratios of the two series of crystalline signals in the X-ray diffraction patterns. The source of the layered structure remains unclear and needs further studies to investigate the spatial arrangement of the chains in more detail. The secondary structure was still not changing upon heating even if a highly crystalline diffraction pattern occurs. Concluding that even the newly investigated crystallization did not show a helix-coil transition in the solid state by annealing, the phenomenon known in solution has to be claimed as unachievable in the solid state based on the results of this work. A remaining open question represents the observation that the same crystalline pattern can be reproducibly prepared with exhibiting two different ordered secondary structures (helix and β-sheet). After the investigation that the evaporation time cannot be decisive for the crystal growth, the choice of a strong hydrogen bonding interrupting solvent is most probably the key to support and induce the crystallization process.

Synthesis, characterization and chemical modification of a cationic polyelectrolyte poly(methylene amine)

Polyamine polymers have attracted attention due to their ability to demonstrate pH dependent cationic nature and presence of highly reactive pendant amino groups. These amino groups make them suitable for a host of applications through cross-linking and derivatization. As a result the end use application of a polyamine is largely driven by the number of amino groups and the way they are attached to the polymer backbone. Thus, this piece of work describes the synthesis and investigation of properties of a novel aliphatic polyamine, poly(methylene amine); that carries maximum number of amino group on its backbone. The target polymer, poly(methylene amine); was synthesized via two major steps viz.1.synthesis of precursor polymers of poly(methylene amine) and 2. Hydrolysis of the precursor polymers to obtain poly(methylene amine). The precursor polymers poly (1,3-diacetylimidazole-2-one)(6) and poly(1,3-diformyldihydroimidazol-2-one)(7) were synthesized via radical polymerization of their respective monomers. The monomers were polymerized in bulk as well as in solution at different reaction conditions. The maximum molecular weights were achieved by polymerizing the monomers in bulk (Mn = 6.5 x 104 g/mol and Mw = 2.13 x 105 g/mol) of 6. The precursor polymers were hydrolyzed under strong reaction conditions in ethanol in presence of NaOH, LiCl at 170°C to yield poly(methylene amine). The process of hydrolysis was monitored by IR spectroscopy. The solution properties of poly(methylene amine) and its hydrochloride were investigated by viscosimetry and light scattering. The reduced viscosity of poly (methylene amine) hydrochloride as a function of polymer concentration demonstrated a behavior typical of cationic polyelectrolyte. With decrease in polymer concentration the reduced viscosity of poly(methylene amine) hydrochloride increased gradually. The dynamic light scattering studies also revealed behaviors of a polyelectrolyte. Poly(methylene amine) was reacted with electrophiles to yield novel materials. While the attachment of alkyl group onto the nitrogen would increase nucleophilicity, it would also impose steric hindrance. As a result the degree of substitution on poly(methylene amine) would be governed by both the factors. Therefore, few model reactions with electrophiles were performed on polvinylamine under similar reaction conditions in order to make a comparative evaluation. It was found that under similar reaction conditions the degree of substitution was higher in case of polyvinylamine in comparison with poly (methylene amine).This shows that the steric hindrance outweighs nucleophilicity while deciding degree of substitution of electrophiles on poly(methylene amine). The modification was further extended to its use as an initiator for ring opening polymerization of benzyloxy protected N-carboxyanhydride of z-Lysine. The resulting polymer had an interesting brush like architecture. The solid state morphology of this polymer was investigated by SAXS. The 2D-WAXS diffractograms revealed hexagonal morphology of peptide segments without formation of alpha helices.

Hyperverzweigte Lacton-Copolymere: enzymatische Synthese, Charakterisierung und Darstellung strukturierter Polymernetzwerke = (Hyperbranched lactone copolymers by enzyme catalysis: synthesis, characterization and preparation of structured polymer networks)

Hyperverzweigte Polymere erfuhren in den letzten Jahren immer mehr Beachtung, da sie im Vergleich zu ihren linearen Analoga besondere Eigenschaften besitzen. Im Jahre 2002 wurde die erste enzymkatalysierte Darstellung hyperverzweigter Poly(epsilon-caprolacton)e (hb-PCL) beschrieben. Hier ermöglichte das Konzept der konkurrierenden ringöffnenden Polymerisation und Polykondensation die Kontrolle der Eigenschaften des dargestellten Polymers. Detaillierte Untersuchungen in Hinblick auf Grenzen und Möglichkeiten, aber auch die Synthese im Technikumsmaßstab sind wesentliche Aspekte dieser Arbeit. Außerdem wird ein neues Konzept eingeführt, das Reknitting genannt wurde. Ziel desselben ist das Recycling kommerziellen, linearen PCLs mittels Umesterung zu hb-PCL durch Enzymkatalyse. Diese hb-PCLs zeigen vergleichbare Eigenschaften zu den aus den Comonomeren dargestellten. Ausgehend von hb-PCL sollte eine geeignete Route zu methacrylierten Vernetzerverbindungen entwickelt werden. Aus Mischungen derselben mit 2-Hydroxyethylmethacrylat wurden komplexe Netzwerkarchitekturen durch Copolymerisation erhalten. Diese Netzwerke wurden in Hinblick auf ihre mechanisch physikalischen Eigenschaften untersucht. Zuletzt wurden Screeningexperimente an anderen zyklischen Estern durchgeführt, da ein Transfer des oben vorgestellten Konzepts angestrebt wurde. Zwei neue hyperverzweigte Polymerklassen, hb-Poly(delta-valerolacton) und hb-Polytrimethylencarbonat wurden detaillierter untersucht und in Ihren Eigenschaften mit hb-PCL verglichen.

Synthese und Charakterisierung von zylindrischen Bürsten mit Polypeptidseitenketten

In der vorliegenden Arbeit konnte gezeigt werden, dass durch die grafting-from-Methode verschiedene geschützte Polypeptidbürsten basierend auf L-glutaminsäure, L-asparaginsäure, L-lysin und L-ornithin synthetisch zugänglich sind. Zur Verwirklichung dieser Synthesestrategie wurde mehrstufig ein Makroinitiator auf Basis von N-methacrylamid-1,6-diaminohexan hergestellt, der die ringöffnende Polymerisation von Leuchs´schen Anhydriden zur Entwicklung von geschützten Polypeptidseitenketten initiieren kann. Durch stark saure bzw. alkalische Abspaltbedingungen war es möglich, die Schutzgruppen bei allen geschützten Bürsten bis auf eine Spezies erfolgreich zu entfernen. Weitergehende Untersuchungen an den positiv bzw. negativ geladenen Polyelektrolytbürsten mittels statischer Lichtstreuung und Kapillarelektrophorese zeigten, dass lediglich die Z-geschützten Poly-L-lysinbürsten ohne Kettenabbau entschützt werden konnten. In allen anderen Fällen wurden nach Abspaltung der Schutzgruppen lineare Kettenfragmente detektiert. Durch die Zugabe von NaClO4 oder Methanol zu den wässrigen Lösungen der Poly-L-lysinbürsten konnte mittels CD-Spektroskopie gezeigt werden, dass die Seitenketten von einer ungeordneten Konformation in eine helikale Konformation übergehen. In weiterführenden Experimenten wurde mittels statischer Lichtstreuung, dynamischer Lichtstreuung, SAXS, und AFM-Aufnahmen in Lösung bewiesen, dass die helikale Konformation der Seitenketten eine deutliche Abnahme des Zylinderquerschnitts und des Querschnittträgheitsradius zur Folge hat, die Topologie der Bürste allerdings unverändert bleibt. Weiterhin konnte mittels Kapillarelektrophorese die elektrophoretische Mobilität der Poly-L-lysinbürsten und ihrer linearen Analoga bestimmt werden. Mit diesen Resultaten war es in Kombination mit statischen Lichtstreuexperimenten möglich, die effektive Ladung von linearem und verzweigten Poly-L-lysin nach einer Theorie von Muthukumar zu berechnen. Das Ergebnis dieser Rechnungen bestätigt die Ergebnisse früherer Untersuchungen von Peter Dziezok, der in seiner Dissertation durch Leitfähigkeits und Lichtstreumessungen an linearem PVP und PVP-Bürsten herausfand, dass die effektive Ladung von Polymerbürsten mindestens um einen Faktor 10 kleiner ist als bei den korrespondierenden linearen Analoga.

Nicht-wässrige Emulsionen zur Erzeugung neuer Nanopartikel

In der eingereichten Arbeit wurde die Nutzung von nicht-wässrigen Emulsionen, bestehend aus zwei organischen, aprotischen Lösungsmitteln, zur Erzeugung verschiedener polymerer Nanopartikel beschrieben. Diese Zweiphasenmischungen und die Verwendung maßgeschneiderter Emulgatoren bestehend aus Poly(isopren-block-methylmethacrylat) ermöglichten den Zugang zu einer Vielzahl an Reaktionen und Prozessen, welche in wässrigen Emulsionen bisher nicht oder nur schwer möglich waren. Die Generierung von Partikeln auf Basis katalytischer Polymerisationen erfolgte unter Verwendung der Ringöffnenden Metathese-Polymerisation (ROMP), der Acyclischen Dien-Metathese-Polymerisation (ADMET), der Cyclopolymerisation von α,ω-Diinen und der Ni-katalysierten Polymerisation von Isocyaniden. Mittels ROMP konnten stabile Dispersionen erzeugt werden, welche Partikel mit verschiedensten Molekulargewichten, Größen und Morphologien enthielten. Diese Eigenschaften konnten durch die Wahl des Monomers, die Katalysatorkonzentration oder den Emulgatortyp beeinflusst werden. Des Weiteren wurden Partikel mit komplexen Morphologien wie Kern-Schale-Strukturen synthetisiert. Dazu erfolgte die Generierung von Partikeln aus Poly(urethan) oder Poly(norbornenderivaten), welche in situ und ohne intermediäre Aufarbeitung mit einer Schale aus Poly(methacrylat) versehen wurden. Der Nachweis dieser Strukturen gelang mittels verschiedener Schwermetall-Markierungsverfahren in der Transmissionselektronenmikroskopie. Schlussendlich erfolgte die Herstellung von hochvernetzten und molekular geprägten Poly(acrylsäure)-Partikeln. Hierbei wurden unterschiedliche pharmakologische Wirkstoffe und Farbstoffe in die Partikel eingebracht, um deren Migrationsverhalten und Wiederanbindung an die Partikel zu untersuchen. Weiterhin wurden die Partikel erfolgreich in Zellaufnahmeexperimenten eingesetzt.