Structural and phase dependent thermo and photoluminescent properties of Dy(OH)(3) and Dy2O3 nanorods

Hexagonal Dy(OH)(3) and cubic Dy2O3 nanorods were prepared by hydrothermal method. Dy(OH)(3) nanorods was directly obtained at 180 degrees C for 20 h after hydrothermal treatment whereas subsequently heat treatment at 750 degrees C for 2 h gives pure cubic Dy2O3. SEM micrographs reveal that needle shaped rods with different sizes were observed in both the phases. TEM results also confirm this. The TL response of hexagonal Dy(OH)(3) and cubic Dy2O3 nanorods have been analyzed for gamma-irradiation over a wide range of exposures (1-5 kGy). TL glow peak intensity increases with gamma dose in both the phases. The activation energy (E), order of kinetics (6), and frequency factor (s) for both the phases have been determined using Chen's peak shape method. The simple glow curve shape, structure and linear response to gamma-irradiation over a large span of exposures makes the cubic Dy2O3 as a useful dosimetric material to estimate high exposures of gamma-rays. (c) 2012 Elsevier Ltd. All rights reserved.

Vanadium pentoxide nanobelts: One pot synthesis and its lithium storage behavior

In this paper, we report a synthesis, characterization and electrochemical properties of V2O5 nanobelts. V2O5 nanobelts have been prepared via hydrothermal treatment of commercial V2O5 in acidic (HCl/H2SO4) medium at relatively low temperature (160 degrees C). The hydrothermally derived products have been characterized by powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, X-ray photo electron spectroscopy (XPS), UV-Vis spectroscopy, Scanning/Transmission electron microscopy (SEM/TEM). XRD pattern of V2O5 nanobelts show an orthorhombic phase. From the FTIR spectrum, the peak observed at 1018 cm-1 is characteristic of the stretching vibration mode of the terminal vanadyl, V = O. The UV-Vis absorption spectrum of V2O5 nanobelts show maximum absorbance at 430 nm, which was blue-shifted compared to that of bulk V2O5. TEM micrographs reveal that the products consist of nanobelts of 40-200 nm in thickness and several tens of micrometers in length. The electrochemical analysis shows an initial discharge capacity of 360 mAh g-1 and its almost stabilized capacity is reached to 250 mAh g-1 after 55 cycles. A probable reaction mechanism for the formation of orthorhombic V2O5 nanobelts is proposed.

Enhanced sunlight photocatalytic activity of Ag3PO4 decorated novel combustion synthesis derived TiO2 nanobelts for dye and bacterial degradation

This study demonstrates the synthesis of TiO2 nanobelts using solution combustion derived TiO2 with enhanced photocatalytic activity for dye degradation and bacterial inactivation. Hydrothermal treatment of combustion synthesized TiO2 resulted in unique partially etched TiO2 nanobelts and Ag3PO4 was decorated using the co-precipitation method. The catalyst particles were characterized using X-ray diffraction analysis, BET surface area analysis, diffuse reflectance and electron microscopy. The photocatalytic properties of the composites of Ag3PO4 with pristine combustion synthesized TiO2 and commercial TiO2 under sunlight were compared. Therefore the studies conducted proved that the novel Ag3PO4/unique combustion synthesis derived TiO2 nanobelt composites exhibited extended light absorption, better charge transfer mechanism and higher generation of hydroxyl and hole radicals. These properties resulted in enhanced photodegradation of dyes and bacteria when compared to the commercial TiO2 nanocomposite. These findings have important implications in designing new photocatalysts for water purification.

Periodic bubble emission and appearance of an ordered bubble sequence (train) during condensation in a single microchannel

Condensation of steam in a single microchannel, silicon test section was investigated visually at low flow rates. The microchannel was rectangular in cross-section with a depth of 30 pm, a width of 800 mu m and a length of 5.0 mm, covered with a Pyrex glass to allow for visualization of the bubble formation process. By varying the cooling rate during condensation of the saturated water vapor, it was possible to control the shape, size and frequency of the bubbles formed. At low cooling rates using only natural air convection from the ambient environment, the flow pattern in the microchannel consisted of a nearly stable elongated bubble attached upstream (near the inlet) that pinched off into a train of elliptical bubbles downstream of the elongated bubble. It was observed that these elliptical bubbles were emitted periodically from the tip of the elongated bubble at a high frequency, with smaller size than the channel width. The shape of the emitted bubbles underwent modifications shortly after their generation until finally becoming a stable vertical ellipse, maintaining its shape and size as it flowed downstream at a constant speed. These periodically emitted elliptical bubbles thus formed an ordered bubble sequence (train). At higher cooling rates using chilled water in a copper heat sink attached to the test section, the bubble formation frequency increased significantly while the bubble size decreased, all the while forming a perfect bubble train flowing downstream of the microchannel. The emitted bubbles in this case immediately formed into a circular shape without any further modification after their separation from the elongated bubble upstream. The present study suggests that a method for controlling the size and generation frequency of microbubbles could be so developed, which may be of interest for microfluidic applications. The breakup of the elongated bubble is caused by the large Weber number at the tip of the elongated bubble induced by the maximum vapor velocity at the centerline of the microchannel inside the elongated bubble and the smaller surface tension force of water at the tip of the elongated bubble.

Characterization of the acid sites in dealuminated nanosized HZSM-5 zeolite with the probe molecule trimethylphosphine

The acid sites in dealuminated HZSM-5 zeolite with crystal sizes down to the nanoscale were firstly characterized by the probe molecule trimethylphosphine (TMP). As evidenced by the combination of P-31 CP/MAS NMR, Al-27 MAS and H-1 --> Al-27 CP/MAS NMR measurements, the Bronsted acid sites of both microsized and nanosized HZSM-5 could be decreased upon the dealumination of zeolitic framework after hydrothermal treatment. At the same time, the appearance of Lewis acid sites was observed. The dealuminated nanosized HZSM-5 is easier to form Lewis acid sites than microsized HZSM-5, and the type of Lewis acid sites in nanosized HSM-5 is more than one. In addition, the origin of Lewis acid sites is mainly associated with the aluminum at ca. 30 ppm, in the Al-27 MAS NMR spectra, and only a part of which in the dealuminated HZSM-5 zeolite acts as Lewis acid sites. (C) 2002 Elsevier Science B.V. All rights reserved.

Luminescent and Mesoporous Europium-Doped Bioactive Glasses (MBG) as a Drug Carrier

Luminescent and mesoporous europium-doped bioactive glasses (MBG:Eu) were successfully synthesized by a two-step acid-catalyzed self-assembly process combined with hydrothermal treatment in an inorganic-organic system. The obtained MBG was performed as a drug delivery carrier to investigate the drug storage/release properties using ibuprofen (IBU) as a model drug. The structural, morphological, textural and optical properties were well characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), N-2 adsorption/desorption, and photoluminescence (PL) spectra, respectively. The results reveal that the MBG exhibit the typical ordered characteristics of the hexagonal mesostructure. This composite shows sustained release profile with ibuprofen as the model drug. The IBU-loaded samples still show red luminescence of Eu3+ (D-5(0)-F-7(1, 2)) under UV irradiation, and the emission intensities of Eu3+ in the drug carrier system vary with the released amount of IBU, thus making the drug release be easily tracked and monitored by the change of the luminescence intensity.

Hexagonal nanodisks of cadmium hydroxide and oxide with nanoporous structure

In this work we demonstrate that hexagonal nanodisks of cadmium hydroxide with nanoporous structures could be fabricated by a facile hydrothermal treatment without using any templates or organic additives. With this method, the length of the hexagonal edge and thickness of the nanodisks can be adjusted through controlling the experimental conditions such as the pH value of the mother liquor and the initial concentration of the cadmium ion. On the basis of our experimental observations and understandings of the nanocrystal growth, the formation of the nanodisks is believed to mainly originate from the oriented attachment of small particles. Furthermore, the hexagonal Cd(OH)(2) nanodisks can be converted to CdO semiconductors with similar morphology by calcinations.

An investigation of the roles of surface aluminum and acid sites in the zeolite MCM-22

Ammonia adsorption studies reveal that the observed Lewis acidity in the zeolite MCM-22 is derived from at least two types of framework aluminum sites (Al(F)), that is, octahedral Al(F) and three-coordinate Al(F). Comparative ammonia or trimethylphosphine (TMP) adsorption experiments with MCM-22 confirm that octahedral Al species gives rise to the signal at delta(ISO) approximate to 0 in the (27)Al NMR spectrum; this is a superposition of two NMR signals from the different Al species on the water-re constructed zeolite surface. A sharp resonance assigned to framework Al reversibly transforms on ammonia adsorption to delta(ISO) (27)Al approximate to 55 from tetrahedral Al(F), while the broad peak is assigned to nonframework aluminium which results from hydrothermal treatment. This study also demonstrates the effectiveness of (27)Al magic angle spinning (MAS) and multiple quantum (MQ) MAS NMR spectroscopy as a technique for the study of zeolite reactions.

The stability of nanosized HZSM-5 zeolite: a high-resolution solid-state NMR study

The thermal and hydrothermal stabilities of HZSM-5 zeolites with crystal sizes less than 100 nm have been studied by multinuclear solid-state NMR, combined with BET and XRD. As evidenced by Al-27 and Si-29 MAS as well as their corresponding cross-polarization/MAS NMR investigations, the thermal stability of nanosized HZSM-5 is not so good as that of microsized HZSM-5. This is due to two processes concerning dealumination and desilicification involved in the calcination of nanosized HZSM-5, while only the dealumination process is conducted in microsized HZSM-5 under the similar calcination process. The hydrothermal stability of nanosized HZSM-5 is, contrary to what was expected, not so bad as that of the microsized HZSM-5 in the course of steam treatment. The actual resistance of the hydrothermal stability to the crystal size of HZSM-5 can be ascribed to an active reconstruction of zeolitic framework through an effective filling of amorphous Si species into nanosized HZSM-5 during hydrothermal treatment. (C) 2001 Published by Elsevier Science B.V.

The study of Ti doped ZSM-5 particles and cavities inside them

The TEM study of titanium-containing ZSM-5 zeolite before and after hydrothermal treatment was performed. The use of different TEM techniques, such as conventional TEM, HRTEM and EDX-line scans provides important information about the microscopic structure of the zeolite catalyst consisting from several phases. The hydrothermal treatment of zeolite powder leads to strong changes in the morphology of the constituting particles. They are characterized by a homogeneous structure before hydrothermal treatment while the occurrence of holes after thermal treatment was observed, These changes lead to the enrichment of zeolite with titanium which obviously enhance its catalytic activity. Some of the titanium surplus precipitates as TiO2 anatase nanoparticles within the holes. (C) 2001 Elsevier Science B.V. All rights reserved.

Effect of variations in acid properties of HZSM-5 on the coking behavior and reaction stability in butene aromatization

In order to investigate the effect of acid properties on the coke behavior and stability of butene aromatization, we prepared the AHZSM-5 samples with various acid properties by the methods of hydrothernial treatment and K addition. The reaction of butene aromatization was carried out at 350 degrees C and 0.5 MPa in a continuous flow fixed bed. The characterization of the fresh/coked catalysts with NH3-TPD, N-2 adsorption-desorption measurement, and TG techniques has shown that a large amount of acid sites (high acid density) of the AHZMS-5 catalyst can cause a large quantity of coke deposit and serious channel blockage, and so result in a rapid loss of aromatization activity. On the contrary, after a great reduction in strong acid sites of AHZSM-5 catalyst resulting from some K-modification, the presence of only many weak acid sites also could not lessen the formation of coke nor improve the reaction stability of butene aromatization. Interestingly, the simultaneous reduction in the strong and weak acid sites to a desirable level by hydrothermal treating the AHZSM-5 catalyst at a proper temperature can effectively suppress the coke formation and channel blockage, and thus improve its olefin aromatization stability. (c) 2005 Elsevier B.V. All rights reserved.

The formation of nanotubes and nanocoils of molybdenum disulphide

This work reports the successful realization of MoS2 nanotubes by a novel intercalation chemistry and hydrothermal treatment. An inorganic-organic precursor of hexadecylamine (HDA) and molybdenum disulphide (MoS2) were used in synthesizing the nanocomposite comprising laminar MoS2 with HDA intercalated in the interlaminar spacing. The formation of MoS2 nanotubes occurred during hydrothermal treatment (HT) by a self-organized rolling mechanism. The nanotubes were observed to have dimensions 2-12 µm in length and inner diameters typically in the range of 25-100 nm. We also report the formation of amorphous nanocoils of MoS2 obtained during similar procedures.

Template-free environmentally friendly synthesis and characterization of unsupported tungsten carbide with a controllable porous framework

Tungsten carbide (WC) with controlled pore size distribution was synthesized using a novel “precursor reassembly” method. The precursor crystal was assembled by mixing ammonium metatungstate (AMT) and ammonium carbonate (AC) in distilled water, followed by hydrothermal treatment. The mesostructure, crystal phase, and amount of deposited graphitic carbon can be conveniently tuned by controlling carburizing atmosphere (CO or a CO/H2 mixture). Moreover, the influence of precursor preparation (AMT/AC mass ratio and hydrothermal temperature) on the materials was also investigated. The resultant materials with low carbon content were mesoporous WCs, which showed high specific surface areas (11.3-20.4 m2 g-1) and adjustable pore-size distributions (average pore size: 15.3-22.3 nm). A mechanism for the formation of WC with a controllable porous framework is proposed. Finally, cyclic voltammetry was used to investigate the inference of different mesoporous structure.

Bottom up strategies for the morphology control of BaTiO3 particulates

As propriedades funcionais dos materiais ferroeléctricos tais como a polarização reversível, piroelectricidade, piezoelectricidade, elevada actividade óptica não linear e comportamento dieléctrico não linear são fundamentais para a sua aplicação em sensores, microactuadores, detectores de infravermelhos, filtros de fase de microondas e memórias não-voláteis. Nos últimos anos, motivado pelas necessidades industriais de redução do tamanho dos dispositivos microelectrónicos, aumentando a eficiência volumétrica, tem sido feito um grande esforço ao nível da investigação para desenvolver estruturas ferroeléctricas à escala micro- e nano- métrica. É sabido que a redução de tamanho em materiais ferroeléctricos afecta significamente as suas propriedades. Neste sentido e considerando que foi previsto teoreticamente por cálculos ab initio que estruturas do tipo nanocilindros e nanodiscos apresentariam um novo tipo de ordem ferroeléctrica e, na expectativa de alcançar conhecimento para o desenvolvimento de uma nova geração de dispositivos microelectróncos, existe um grande interesse em desenvolver métodos de fabrico de nanoestruturas ferroeléctricas unidimensionais (1D) tais como nanocilindros e nanotubos. As estratégias de fabrico de nanoestruturas 1D até agora descritas na literatura indicam claramente as dificuldades inerentes à sua preparação. Existem duas grandes vias de síntese destas nanoestruturas: i) o método “topdown” que consiste na redução de tamanho de um dado material até à obtenção duma estrutura 1D; e ii) o método “bottom-up” em que átomos, iões e moléculas são agrupados para formar um material 1D. O método “top down” envolve em geral técnicas de desgaste, como o uso do feixe de electrões, que apesar de permitirem elevada precisão no posicionamento e no controlo do tamanho, falham em termos de resolução, exigem muito tempo e causam facilmente defeitos que deterioram as propriedades físicas destes materiais. Na metodologia “bottom up” a utilização de moléculas ou estruturas “molde” tem sido a mais explorada. As estructuras 1D podem também ser preparadas sem recorrer a “moldes”. Neste caso a agregação orientada é promovida pelo recurso a aditivos que controlam o crescimento dos cristais em direcções preferenciais. Neste contexto, neste trabalho utilizaram-se duas estratégias “bottom up” de baixo custo para a preparação de nanopartículas de titanato de bário (BaTiO3) com morfologia controlada: 1) síntese química (em solução e em fase vapor) com utilização de nanotubos de titanato TiNTs) como “moldes” e precursores de titânio 2) síntese química em solução com presença de aditivos. Os nanotubos de titanato de sódio foram preparados por síntese hidrotermal. Como existiam muitas dúvidas acerca da natureza estrutural e do mecanismo de formação dos NTs, a parte inicial do trabalho foi dedicada à realização de um estudo sistemático dos parâmetros intervenientes na síntese e à caracterização da sua estrutura e microestrutura. Foi demonstrado que os NTs têm a fórmula geral A2Ti2O5 (A = H+ or Na+), e não TiO2 (anátase) com defendido por vários autores na literatura, e podem ser preparados por método hidrotermal em meio fortemente alcalino usando como fonte de titânio TiO2 comercial na forma de anátase ou rútilo. A menor reactividade do rútilo exige temperaturas de síntese superiores ou tempos de reacção mais longos. A forma tubular resulta do tratamento hidrotermal e não de processos de lavagem e neutralização subsequentes. Se os NTs forem tratados após a síntese hidrotérmica em água a 200 ºC, transformam-se em nanocilindros. Uma das partes principais desta tese consistiu na investigação do papel dos NTs de titanato no crescimento anisotrópico de BaTiO3. O potencial funcionamento dos NTs como “moldes” para além de precursores foi testado em reacção com hidróxido de bário em síntese em solução e por reacção com um precursor orgânico de bário em fase vapor. Tendo por base os estudos cinéticos realizados, bem como as alterações estruturais e morfológicas das amostras, é possível concluir que a formação do BaTiO3 a partir de NTs de titanato de sódio, ocorre por dois mecanismos dependendo da temperatura e tempo de reacção. Assim, a baixa temperatura e curto tempo de reacção verifica-se que se formam partículas dendríticas de BaTiO3 cuja superfície é bastante irregular (“wild”) e que apresentam estrutura pseudo-cúbica. Estas partículas formam-se por reacção topotáctica na fronteira dos nanotubos de titanato de sódio. A temperaturas mais altas e/ou reacções mais longas, a reacção é controlada por um mecanismo de dissolução e precipitação com formação de dendrites de BaTiO3 tetragonais com superfície mais regular (“seaweed”). A microscopia de força piezoeléctrica mostrou que as dendrites “seaweeds“ possuem actividade piezoeléctrica superior à das dendrites “wild”, o que confirma o papel desempenhado pela estrutura e pela concentração de defeitos na rede na coerência e ordem ferroeléctrica de nanoestruturas. Os nossos resultados confirmam que os NTs de titanato não actuam facilmente como “moldes” na síntese em solução de BaTiO3 já que a velocidade de dissolução dos NTs em condições alcalinas é superior à velocidade de formação do BaTiO3. Assumindo que a velocidade de reacção dos NTs com o precursor de bário é superior em fase vapor, efectuou-se a deposição de um precursor orgânico de bário por deposição química de vapor sobre um filme de NTs de titnato de sódio depositados por deposição electroforética. Estudou-se a estabilidade dos NTs nas diferentes condições do reactor. Quando os NTs são tratados a temperaturas superiores a 700 ºC, ocorre a transformação dos NTs em nanocilindros de anatase por um mecanismo de agregação orientada. Quando se faz a deposição do precursor de bário, seguida de calcinação a 700 ºC em atmosfera oxidante de O2, verifica-se que a superficie dos NTs fica coberta com nanocristais de BaTiO3 independentemente da concentração de bário. O papel dos NTs de titanato no crescimento anisotrópico de BaTiO3 em fase vapor é assim descrito pela primeira vez. Em relação à metodologias de crescimento de partículas na ausência de “moldes” mas com aditivos fez-se um estudo sistemático utilizando 5 aditivos de natureza differente. As diferenças entre aditivos foram sistematizadas tendo em conta as diferenças estruturais e morfológicas verificadas. Está provado que os aditivos podem funcionar como modificadores de crescimento cristalino por alteração do seu padrão de crescimento ou por alteração da cinética de crescimento das faces cristalográficas do cristal. Entre os aditivos testados verificou-se que o ácido poliacrilíco adsorve em faces específicas do BaTiO3 alterando a cinética de crescimento e induzindo a agregação orientada das partículas. O polivinilpirrolidona, o docecilsulfato de sódio e hidroxipropilmetilcelulose actuam mais como inibidores de crescimento do que como modificadores do tipo de crescimento. A D-frutose aumenta a energia de activação da etapa de nucleação não ocorrendo formação de BaTiO3 para as mesmas condições dos outros aditivos. Esta tese clarifica o papel dos NTs de titanato de sódio enquanto precursores e “moldes” no crescimento anisotrópico de BaTiO3 em solução e em fase vapor. É feita também a abordagem do controlo morfológico do BaTiO3 através do uso de aditivos. As estratégias de preparação de BaTiO3 propostas são de baixo custo, reprodutíveis e fáceis de efectuar. Os resultados contribuem para uma melhor compreensão da relação tamanho – morfologia – propriedade em materiais ferroeléctricos nanométricos com vista à sua potencial aplicação.