Open to the users' needs : combining user-centered design, standards and open source software

This case study introduces our continuous work to enhance the virtual classroom in order to provide faculty and students with an environment open to their needs, compliant with learning standards and, therefore compatible with other e-learning environments, and based on open source software. The result is a modulable, sustainable and interoperable learning environment that can be adapted to different teaching and learning situations by incorporating the LMS integrated tools as well as wikis, blogs, forums and Moodle activities among others.

Design Guide and Construction Specifications for National Pollutant Discharge Elimination System (NPDES) Site Runoff Control, 2006

According to the 1972 Clean Water Act, the Environmental Protection Agency (EPA) established a set of regulations for the National Pollutant Discharge Elimination System (NPDES). The purpose of these regulations is to reduce pollution of the nation’s waterways. In addition to other pollutants, the NPDES regulates stormwater discharges associated with industrial activities, municipal storm sewer systems, and construction sites. Phase II of the NPDES stormwater regulations, which went into effect in Iowa in 2003, applies to construction activities that disturb more than one acre of ground. The regulations also require certain communities with Municipal Separate Storm Sewer Systems (MS4) to perform education, inspection, and regulation activities to reduce stormwater pollution within their communities. Iowa does not currently have a resource to provide guidance on the stormwater regulations to contractors, designers, engineers, and municipal staff. The Statewide Urban Design and Specifications (SUDAS) manuals are widely accepted as the statewide standard for public improvements. The SUDAS Design manual currently contains a brief chapter (Chapter 7) on erosion and sediment control; however, it is outdated, and Phase II of the NPDES stormwater regulations is not discussed. In response to the need for guidance, this chapter was completely rewritten. It now escribes the need for erosion and sediment control and explains the NPDES stormwater regulations. It provides information for the development and completion of Stormwater Pollution Prevention Plans (SWPPPs) that comply with the stormwater regulations, as well as the proper design and implementation of 28 different erosion and sediment control practices. In addition to the design chapter, this project also updated a section in the SUDAS Specifications manual (Section 9040), which describes the proper materials and methods of construction for the erosion and sediment control practices.

The effects of structural reforms on productivity and profitability enhancing reallocation: Evidence from Colombia

Estimates for the U.S. suggest that at least in some sectors productivity enhancing reallocationis the dominant factor in accounting for producitivity growth. An open question, particularlyrelevant for developing countries, is whether reallocation is always productivity enhancing. Itmay be that imperfect competition or other barriers to competitive environments imply that thereallocation process is not fully e?cient in these countries. Using a unique plant-levellongitudinal dataset for Colombia for the period 1982-1998, we explore these issues byexamining the interaction between market allocation, and productivity and profitability.Moreover, given the important trade, labor and financial market reforms in Colombia during theearly 1990's, we explore whether and how the contribution of reallocation changed over theperiod of study. Our data permit measurement of plant-level quantities and prices. Takingadvantage of the rich structure of our price data, we propose a sequential mehodology to estimateproductivity and demand shocks at the plant level. First, we estimate total factor productivity(TFP) with plant-level physical output data, where we use downstream demand to instrumentinputs. We then turn to estimating demand shocks and mark-ups with plant-level price data, usingTFP to instrument for output in the inversedemand equation. We examine the evolution of thedistributions of TFP and demand shocks in response to the market reforms in the 1990's. We findthat market reforms are associated with rising overall productivity that is largely driven byreallocation away from low- and towards highproductivity businesses. In addition, we find thatthe allocation of activity across businesses is less driven by demand factors after reforms. Wefind that the increase in aggregate productivity post-reform is entirely accounted for by theimproved allocation of activity.

The Smiling Project: development of a new program for gait and balance training

Introduction: The SMILING project, a multicentric project fundedby the European Union, aims to develop a new gait and balance trainingprogram to prevent falls in older persons. The program includes the"SMILING shoe", an innovative device that generates mechanical perturbationwhile walking by changing the soles' inclination. Induced perturbationschallenge subjects' balance and force them to react to avoidfalls. By training specifically the complex motor reactions used to maintainbalance when walking on irregular ground, the program will improvesubjects' ability to react in situation of unsteadiness and reduce theirrisk of falling. Methods: The program will be evaluated in a multicentric,cross-over randomized controlled trial. Overall, 112 subjects (aged≥65 years, ≥1 falls, POMA score 22-26/28) will be enrolled. Subjectswill be randomised in 2 groups: group A begin the training with active"SMILING shoes", group B with inactive dummy shoes. After 4 weeksof training, group A and B will exchange the shoes. Supervised trainingsessions (30 minutes twice a week for 8 weeks) include walkingtasks of progressive difficulties.To avoid a learning effect, "SMILINGshoes" perturbations will be generated in a non-linear and chaotic way.Gait performance, fear of falling, and acceptability of the program willbe assessed. Conclusion: The SMILING program is an innovative interventionfor falls prevention in older persons based on gait and balancetraining using chaotic perturbations. Because of the easy use of the"SMILING shoes", this program could be used in various settings, suchas geriatric clinics or at home.

Design Procedures and Field Monitoring of Submerged Barbs for Streambank Protection, June 2007

The main objective of this study was to evaluate the hydraulic performance of riprap spurs and weirs in controlling bank erosion at the Southern part of the Raccoon River upstream U.S. Highway 169 Bridge utilizing the commercially available model FESWMS and field monitoring. It was found based on a 2 year monitoring and numerical modeling that the design of structures was overall successful, including their spacing and stability. The riprap material incorporated into the structures was directly and favorably correlated to the flow transmission through the structure, or in other words, dictated the permeable nature of the structure. It was found that the permeable dikes and weirs chosen in this study created less volume of scour in the vicinity of the structure toes and thus have less risk comparatively to other impermeable structures to collapse. The fact that the structures permitted the transmission of flow through them it allowed fine sand particles to fill in the gaps of the rock interstices and thus cement and better stabilize the structures. During bank-full flows the maximum scour hole was recorded away from the structures toe and the scourhole size was directly related to the protrusion angle of the structure to the flow. It was concluded that the proposed structure inclination with respect to the main flow direction was appropriate since it provides maximum bank protection while creating the largest volume of local scour away from the structure and towards the center of the channel. Furthermore, the lowest potential for bank erosion also occurs with the present set-up design chosen by the IDOT. About 2 ft of new material was deposited in the area located between the structures for the period extending from the construction day to May 2007. Surveys obtained by sonar and the presence of vegetation indicate that new material has been added at the bank toes. Finally, the structures provided higher variability in bed topography forming resting pools, creating flow shade on the leeward side of the structure, and separation of bed substrate due to different flow conditions. Another notable environmental benefit to rock riprap weirs and dikes is the creation of resting pools, especially in year 2007 (2nd year of the project). The magnitude of these benefits to aquatic habitat has been found in the literature that is directly related to the induced scour-hole volume.

Design, synthesis and biological evaluation of a class of bioisosteric oximes of the novel dual peroxisome proliferator-activated receptor α/γ ligand LT175.

The effects resulting from the introduction of an oxime group in place of the distal aromatic ring of the diphenyl moiety of LT175, previously reported as a PPARα/γ dual agonist, have been investigated. This modification allowed the identification of new bioisosteric ligands with fairly good activity on PPARα and fine-tuned moderate activity on PPARγ. For the most interesting compound (S)-3, docking studies in PPARα and PPARγ provided a molecular explanation for its different behavior as full and partial agonist of the two receptor isotypes, respectively. A further investigation of this compound was carried out performing gene expression studies on HepaRG cells. The results obtained allowed to hypothesize a possible mechanism through which this ligand could be useful in the treatment of metabolic disorders. The higher induction of the expression of some genes, compared to selective agonists, seems to confirm the importance of a dual PPARα/γ activity which probably involves a synergistic effect on both receptor subtypes.

Identification of Practices, Design, Construction, and Repair Using Trenchless Technology, TR-570, 2010

Trenchless technologies are methods used for the construction and rehabilitation of underground utility pipes. These methods are growing increasingly popular due to their versatility and their potential to lower project costs. However, the use of trenchless technologies in Iowa and their effects on surrounding soil and nearby structures has not been adequately documented. Surveys of and interviews with professionals working in trenchless-related industries in Iowa were conducted, and the results were analyzed and compared to survey results from the United States as a whole. The surveys focused on method familiarity, pavement distress observed, reliability of trenchless methods, and future improvements. Results indicate that the frequency of pavement distress or other trenchless-related issues are an ongoing problem in the industry. Inadequate soil information and quality control/quality assurance (QC/QA) are partially to blame. Fieldwork involving the observation of trenchless construction projects was undertaken with the purpose of documenting current practices and applications of trenchless technology in the United States and Iowa. Field tests were performed in which push-in pressure cells were used to measure the soil stresses induced by trenchless construction methods. A program of laboratory soil testing was carried out in conjunction with the field testing. Soil testing showed that the installations were made in sandy clay or well-graded sand with silt and gravel. Pipes were installed primarily using horizontal directional drilling with pipe diameters from 3 to 12 inches. Pressure cell monitoring was conducted during the following construction phases: pilot bore, pre-reaming, and combined pipe pulling and reaming. The greatest increase in lateral earth pressure was 5.6 psi and was detected 2.1 feet from the centerline of the bore during a pilot hole operation in sandy lean clay. Measurements from 1.0 to 2.5 psi were common. Comparisons were made between field measurements and analytical and finite element calculation methods.

Design, Construction, and Field Testing of an Ultra High Performance Concrete Pi-Girder Bridge, TR-574, 2011

Among the variety of road users and vehicle types that travel on U.S. public roadways, slow moving vehicles (SMVs) present unique safety and operations issues. SMVs include vehicles that do not maintain a constant speed of 25 mph, such as large farm equipment, construction vehicles, or horse-drawn buggies. Though the number of crashes involving SMVs is relatively small, SMV crashes tend to be severe. Additionally, SMVs can be encountered regularly on non-Interstate/non-expressway public roadways, but motorists may not be accustomed to these vehicles. This project was designed to improve transportation safety for SMVs on Iowa’s public roadway system. This report includes a literature review that shows various SMV statistics and laws across the United States, a crash study based on three years of Iowa SMV crash data, and recommendations from the SMV community.

Improvement of productivity and polysaccharide-protein complex in Agaricus blazei

The objective of this work was to assess the productivity and polysaccharide-protein complex content of Agaricus blazei on rice straw medium, in comparison to conventional sawdust, using four casing soils. The A. blazei strain used was BCRC36814T, purchased from the Food Industry Research and Development Institute, Hsin-Chu, Taiwan. The two media were evaluated as to A. blazei productivity, harvesting time, and production costs. The experimental design used was a randomized complete block, with four replicates. Three local casing soils - Typic Paleudult (CCe), Typic Udorthent (Tq) and Oxyaquic Paleudult (TSp) - were compared to imported peat soil (PS, Saprists, Histosols), used as the control. The productivity of A. blazei using Tq and TSp soil was significantly higher. The TSp casing treatment resulted in earlier harvest by at least 14 to 27 days, when compared to the other treatments. The polysaccharide content in CCe (13.2%) and Tq soils (13.2%) did not differ significantly from the PS (13.4%) and TSp (10.6%) treatments. Local casing soils decreased the production costs of A. blazei cultivation. Composted rice straw can substitute sawdust as the culture medium for A. blazei production with increased yield.

Cost information in engineering design -Potentials and limitations of activity-based costing

The purpose of this thesis is to analyse activity-based costing (ABC) and possible modified versions ofit in engineering design context. The design engineers need cost information attheir decision-making level and the cost information should also have a strong future orientation. These demands are high because traditional management accounting has concentrated on the direct actual costs of the products. However, cost accounting has progressed as ABC was introduced late 1980s and adopted widely bycompanies in the 1990s. The ABC has been a success, but it has gained also criticism. In some cases the ambitious ABC systems have become too complex to build,use and update. This study can be called an action-oriented case study with some normative features. In this thesis theoretical concepts are assessed and allowed to unfold gradually through interaction with data from three cases. The theoretical starting points are ABC and theory of engineering design process (chapter2). Concepts and research results from these theoretical approaches are summarized in two hypotheses (chapter 2.3). The hypotheses are analysed with two cases (chapter 3). After the two case analyses, the ABC part is extended to cover alsoother modern cost accounting methods, e.g. process costing and feature costing (chapter 4.1). The ideas from this second theoretical part are operationalized with the third case (chapter 4.2). The knowledge from the theory and three cases is summarized in the created framework (chapter 4.3). With the created frameworkit is possible to analyse ABC and its modifications in the engineering design context. The framework collects the factors that guide the choice of the costing method to be used in engineering design. It also illuminates the contents of various ABC-related costing methods. However, the framework needs to be further tested. On the basis of the three cases it can be said that ABC should be used cautiously when formulating cost information for engineering design. It is suitable when the manufacturing can be considered simple, or when the design engineers are not cost conscious, and in the beginning of the design process when doing adaptive or variant design. If the design engineers need cost information for the embodiment or detailed design, or if manufacturing can be considered complex, or when design engineers are cost conscious, the ABC has to be always evaluated critically.

Design, implementation and testing of DVB/MHP-application development environment

Tämä diplomityö esittelee 1.6. - 4.11.2002 Mikkelin ammattikorkeakoulun YTI-tutkimuskeskuksen Informaatio- ja mediateknologian hankekokonaisuuden STRIMT-projektin puitteissa tekemäni MHP-kehitysjärjestelmähankinnan tuloksia. Digitaalitelevision MHP-sovelluskehitysjärjestelmän hankinnan tulosten lisäksi työ antaa yleiskuvan MHP-sovelluskehitystyökaluista, digitaalitelevisiostandardeista sekä digitaalitelevisioverkkojen yhteistoimintamalleista televerkkojen kanssa. Keräämieni tietojen, tekemäni tarvemäärittelyn ja suorittamani tuotevertailun perusteella valitsin tarpeisiimme sopivimmaksi järjestelmäksi Alticast Inc.-yrityksen Altifusion-tuotteen. Tuotteen valinnassa otin huomioon myös mahdolliset tulevaisuuden tarpeet aina täysimittaista lähetysjärjestelmää varten kehittämällä vaiheittaisen hankintasuunnitelman. Järjestelmää hankittaessa tärkeintä on huomioida heti alusta alkaen mahdolliset tulevat tarpeet ja varmistaa hankinnan hyödynnettävyys myös tulevaisuudessa. Järjestelmän hankinnan lisäksi vastasin sen käyttöönotosta ja järjestelmää hyödyntävän testisovelluksen laatimisesta.

Quality, Productivity and Economy in Welding Manufacturing - Case Study: West Africa

This thesis studies quality, productivity and economy in welding manufacturing in West African states such as Ghana, Nigeria and Cameroon. The study consists of two parts: the first part, which forms the theoretical background, reviews relevant literature concerning the metal and welding industries, and measurement of welding quality, productivity and economy. The second part, which is the empirical part, aims to identify activities in the metal manufacturing industries where welding is extensively used and to determine the extent of welding quality, productivity and economy measurements in companies operating in the metal manufacturing industries. Additionally, the thesis aims to identify challenges that companies face and to assess the feasibility of creating a network to address these issues. The research methods used in the empirical part are the case study (qualitative) method and the survey (quantitative) method. However, the case study method was used to elicit information from companies in Ghana, while the survey method was used to elicit information from companies in Nigeria and Cameroon. The study considers important areas that contribute to creating awareness and understanding of the current situation of the welding industry in West Africa. These areas include the metal manufacturing industrial sector, metal products manufactured, metal production and manufacturing systems deployed, welding quality, productivity and economy measurement systems utilized, equipment and materials on the markets, general challenges facing companies in welding operations, welding technology programs and research in local universities, and SWOT analysis of the various West African states. The notable findings indicate that majority of the companies operate in the constructionindustrial sector. Also, majority of the companies are project manufacturing oriented, thus provide services to customers operating in the growing industries such as the oil and gas, mining, food and the energy industry. In addition, only few companies are certified under standards such as ISO 9001, ISO 3834, and OHSAS 18001. More so, majority of the companies employ manual welding technique, and shielded metal arc welding (SMAW) as the commonly used welding process. Finally, welder salary is about € 300 / month as of June 2013 and the average operations turnover of medium to large companies is about € 5 million / year as at 2012. Based on analysis of the results of the study, it is noted that while welding activities are growing, the availability of cheap labor, the need for company and welder qualification and certification, and the need to manufacture innovative products through developmental projects (transfer of welding expertise and technology) remain as untapped opportunities in the welding industry in the West African states. The study serves as a solid platform for further research and concludes with several recommendations for development of the West African welding industry.

Organisational purchasing of service design – Agency and client perspectives

There has been an increase in the interest in service design, as companies have become more customer-centric and their focus has shifted to customer experiences. The actual organisational purchasing of service design has been given little attention, until recent years. The purpose of this study is to explore the purchasing of service design from the perspectives of sellers (service design agencies) and buying clients (business organisations). In order to understand the phenomenon, also agencies and clients’ approaches to service design discipline, purchasing processes, challenges related to purchasing and ways of facilitating the purchasing are explored. The research follows qualitative research method and utilises abductive reasoning. A proposition framework was formed by combining services marketing, design and organisational buying behaviour literatures, and was tested against real-life business cases. Empirical data was gathered by interviewing eight service design agency representatives and five client representatives in Finland. The results of semi-structural interviews were analysed by finding repetitive themes. The proposition framework was updated according to interview findings. There were both similarities and differences in service design agencies and clients’ approaches to service design. Service design represents a strategic activity to both parties, and it helps in clients’ business development and in discovering opportunities. It is an ideology; a way of thinking and working. The driving force for purchasing service design seemed to be something else than service design itself. Projects have been bought for 1) change and innovation related development, 2) channel related development or for 3) customer experience related development. Seven purchasing challenge themes were recognised: 1) poor or differing service design understanding, 2) selling of service design, 3) varying expectations, 4) difficulty of pre-evaluation, 5) buyers and buying companies, 6) project process and nature and 7) unclear project results. These all can be considered to cause challenges in organisational service design purchasing. Challenges can be caused by either participant, the agency or the client, and take place at any point of the purchasing process. Some of the challenges could be considered as barriers to purchasing or they play a role in an unsuccessful service project – and therefore, result in an unsuccessful organisational purchase. Purchasing could be facilitated in various ways by either participant; some ways are more attitude based, others actionable improvements. Thesis’s theoretical and managerial findings can be utilised to both improve the selling and purchasing of service design services.

Design, development and assessment of the Java Intelligent Tutoring System

The "Java Intelligent Tutoring System" (JITS) research project focused on designing, constructing, and determining the effectiveness of an Intelligent Tutoring System for beginner Java programming students at the postsecondary level. The participants in this research were students in the School of Applied Computing and Engineering Sciences at Sheridan College. This research involved consistently gathering input from students and instructors using JITS as it developed. The cyclic process involving designing, developing, testing, and refinement was used for the construction of JITS to ensure that it adequately meets the needs of students and instructors. The second objective in this dissertation determined the effectiveness of learning within this environment. The main findings indicate that JITS is a richly interactive ITS that engages students on Java programming problems. JITS is equipped with a sophisticated personalized feedback mechanism that models and supports each student in his/her learning style. The assessment component involved 2 main quantitative experiments to determine the effectiveness of JITS in terms of student performance. In both experiments it was determined that a statistically significant difference was achieved between the control group and the experimental group (i.e., JITS group). The main effect for Test (i.e., pre- and postiest), F( l , 35) == 119.43,p < .001, was qualified by a Test by Group interaction, F( l , 35) == 4.98,p < .05, and a Test by Time interaction, F( l , 35) == 43.82, p < .001. Similar findings were found for the second experiment; Test by Group interaction revealed F( 1 , 92) == 5.36, p < .025. In both experiments the JITS groups outperformed the corresponding control groups at posttest.