Characterization of turbulent jets from high-aspect-ratio rectangular nozzles

Turbulent free jets issuing from rectangular slots with various high aspect ratios (15-120) are characterized. The centerline mean and rms velocities are measured using hot-wire anemometry over a downstream distance of up to 160 slot heights at a slot-height-based Reynolds number of 10000. Experimental results suggest that a rectangular jet with sufficiently high aspect ratio (> 15) may be distinguished between three flow zones: an initial quasi-plane-jet zone, a transition zone, and a final quasi-axisymmetric-jet zone. In the quasi-plane-jet zone, the turbulent velocity field is statistically similar, but not identical, to those of a plane jet. (c) 2005 American Institute of Physics.

Investigation of the flow field of a highly heated jet of air

Measurements of mean and fluctuating velocity and temperature and their self- and cross-products to the third-order are presented for a heated axisymmetric air jet. Froude numbers in the range of 3500 13,190, Reynolds numbers in the range of 3470-8500 and non-dimensional streamwise distances. X*, from 0.27 to 1.98 are covered by the data. It was found that turbulence intensity decreases for the heated jet in the region between the inertia dominated and the buoyancy dominated regions which is contrary to findings with helium jets mixing with ambient air to produce density fluctuations. The effects of heating on the turbulent kinetic energy budget and the temperature variance budget show small differences for the inertia dominated region and the intermediate region which help to explain the transition process to the far field plume region. Constants are evaluated for the isotropic eddy diffusivity and generalised gradient hypothesis models as well as the scalar variance model. No significant effect of heating on the dissipation time-scale ratio was found. A novel wire array with an inclined cold wire was used. Measurements obtained with this probe are found to lead to asymmetries in some of the higher-order products. Further investigation suggested that the asymmetries are attributable to an as yet unreported interference effect produced by the leading prong of the inclined temperature wire, The effect may also have implications for inclined velocity wires which contain a temperature component when used in heated flows. (C) 2002 Elsevier Science Inc. All rights reserved.

Flexible organic–inorganic hybrid layer encapsulation for organic opto-electronic devices

In this work we produce and study the flexible organic–inorganic hybrid moisture barrier layers for the protection of air sensitive organic opto-electronic devices. The inorganic amorphous silicon nitride layer (SiNx:H) and the organic PMMA [poly (methyl methacrylate)] layer are deposited alternatingly by using hot wire chemical vapor deposition (HW-CVD) and spin-coating techniques, respectively. The effect of organic–inorganic hybrid interfaces is analyzed for increasing number of interfaces. We produce highly transparent (∼80% in the visible region) hybrid structures. The morphological properties are analysed providing a good basis for understanding the variation of the water vapor transmission rate (WVTR) values. A minimum WVTR of 4.5 × 10−5g/m2day is reported at the ambient atmospheric conditions for 7 organic/inorganic interfaces. The hybrid barriers show superb mechanical flexibility which confirms their high potential for flexible applications.

Optimització i implementació en Simulink de l'adquisició d'un senyal GPS amb blocs FFT

Aquest projecte es tracta de la optimització i la implementació de l’etapa d’adquisició d’un receptor GPS. També inclou una revisió breu del sistema GPS i els seus principis de funcionament. El procés d’adquisició s’ha estudiat amb detall i programat en els entorns de treball Matlab i Simulink. El fet d’implementar aquesta etapa en dos entorns diferents ha estat molt útil tant de cara a l’aprenentatge com també per la comprovació dels resultats obtinguts. El principal objectiu del treball és el disseny d’un model Simulink que es capaç d’adquirir una senyal capturada amb hardware real. En realitat, s’han fet dues implementacions: una que utilitza blocs propis de Simulink i l’altra que utilitza blocs de la llibreria Xilinx. D’aquesta manera, posteriorment, es facilitaria la transició del model a la FPGA utilitzant l’entorn ISE de Xilinx. La implementació de l’etapa d’adquisició es basa en el mètode de cerca de fase de codi en paral·lel, el qual empra la operació correlació creuada mitjançant la transformada ràpida de Fourier (FFT). Per aquest procés es necessari realitzar dues transformades (per a la senyal entrant i el codi de referència) i una antitransformada de Fourier (per al resultat de la correlació). Per tal d’optimitzar el disseny s’utilitza un bloc FFT, ja que tres blocs consumeixen gran part dels recursos d’una FPGA. En lloc de replicar el bloc FFT, en el model el bloc és compartit en el temps gràcies a l’ús de buffers i commutadors, com a resultat la quantitat de recursos requerits per una implementació en una FPGA es podria reduir considerablement.

Caracterització estadística dels pics de correlació a GPS

Aquest projecte es centra a donar una caracterització estadística del valor que tenen els pics de correlació sota diferents escenaris d’adquisició a un receptor GPS. En primer lloc, s’ha volgut donar una visió general de tots els fonaments del sistema GPS per tal de poder entendre el seu funcionament. A continuació, s’ha passat a analitzar el bloc d’adquisició d’un receptor GPS. Primer, hem estudiat quines operacions es realitzen en aquest bloc i quines són les diferents formes d’implementar-lo. Seguidament, sota un escenari d’adquisició per cerca de fase de codi en paral·lel i utilitzant integracions coherents, s’han estudiat les distribucions estadístiques de les pdf’s obtingudes pels pics de correlació de senyal+soroll i pels pics de correlació de només soroll, i s’ha vist com aquestes fan modificar la corba ROC del receptor . Les simulacions s’han realitzat amb MATLAB i en diferents escenaris d’adquisició per tal de poder comparar com varien les estadístiques obtingudes en casos diferents.

Reliable tidal volume estimates at the airway opening with an infant monitor during high-frequency oscillatory ventilation.

OBJECTIVE: To assess the suitability of a hot-wire anemometer infant monitoring system (Florian, Acutronic Medical Systems AG, Hirzel, Switzerland) for measuring flow and tidal volume (Vt) proximal to the endotracheal tube during high-frequency oscillatory ventilation. DESIGN: In vitro model study. SETTING: Respiratory research laboratory. SUBJECT: In vitro lung model simulating moderate to severe respiratory distress. INTERVENTION: The lung model was ventilated with a SensorMedics 3100A ventilator. Vt was recorded from the monitor display (Vt-disp) and compared with the gold standard (Vt-adiab), which was calculated using the adiabatic gas equation from pressure changes inside the model. MEASUREMENTS AND MAIN RESULTS: A range of Vt (1-10 mL), frequencies (5-15 Hz), pressure amplitudes (10-90 cm H2O), inspiratory times (30% to 50%), and Fio2 (0.21-1.0) was used. Accuracy was determined by using modified Bland-Altman plots (95% limits of agreement). An exponential decrease in Vt was observed with increasing oscillatory frequency. Mean DeltaVt-disp was 0.6 mL (limits of agreement, -1.0 to 2.1) with a linear frequency dependence. Mean DeltaVt-disp was -0.2 mL (limits of agreement, -0.5 to 0.1) with increasing pressure amplitude and -0.2 mL (limits of agreement, -0.3 to -0.1) with increasing inspiratory time. Humidity and heating did not affect error, whereas increasing Fio2 from 0.21 to 1.0 increased mean error by 6.3% (+/-2.5%). CONCLUSIONS: The Florian infant hot-wire flowmeter and monitoring system provides reliable measurements of Vt at the airway opening during high-frequency oscillatory ventilation when employed at frequencies of 8-13 Hz. The bedside application could improve monitoring of patients receiving high-frequency oscillatory ventilation, favor a better understanding of the physiologic consequences of different high-frequency oscillatory ventilation strategies, and therefore optimize treatment.

Real-time monitoring of the silicidation process of tungsten filaments at high temperature used as catalysers for silane decomposition

The scope of this work is the systematic study of the silicidation process affecting tungsten filaments at high temperature (1900ºC) used for silane decomposition in the hot-wire chemical vapour deposition technique (HWCVD). The correlation between the electrical resistance evolution of the filaments, Rfil(t), and the different stages of the their silicidation process is exposed. Said stages correspond to: the rapid formation of two WSi2 fronts at the cold ends of the filaments and their further propagation towards the middle of the filaments; and, regarding the hot central portion of the filaments: a initial stage of silicon dissolution into the tungsten bulk, with a random duration for as-manufactured filaments, followed by the inhomogeneous nucleation of W5Si3 (which is later replaced by WSi2) and its further growth towards the filaments core. An electrical model is used to obtain real-time information about the current status of the filaments silicidation process by simply monitoring their Rfil(t) evolution during the HWCVD process. It is shown that implementing an annealing pre-treatment to the filaments leads to a clearly repetitive trend in the monitored Rfil(t) signatures. The influence of hydrogen dilution of silane on the filaments silicidation process is also discussed.

Study of post-deposition contamination in low-temperature deposited polysilicon films

The presence of hydrogen in polysilicon films obtained at low temperatures by hot-wire CVD and the post-deposition oxidation by air-exposure of the films are studied in this paper. The experimental results from several characterization techniques (infrared spectroscopy, X-ray photoelectron spectroscopy, secondary ion mass spectrometry and wavelength dispersive spectroscopy) showed that hydrogen and oxygen are homogeneously distributed at grain boundaries throughout the depth of the films. Hydrogen is introduced during the growth process and its concentration is higher in samples deposited at lower temperatures. Oxygen diffuses along the grain boundaries and binds to silicon atoms, mainly in Si 2O groups.

Optimization of KOH etching process to obtain textured substrates suitable for heterojunction solar cells fabricated by HWCVD

In this work, we have studied the texturization process of (100) c-Si wafers using a low concentration potassium hydroxide solution in order to obtain good quality textured wafers. The optimization of the etching conditions have led to random but uniform pyramidal structures with good optical properties. Then, symmetric heterojunctions were deposited by Hot-Wire CVD onto these substrates and the Quasi-Steady-State PhotoConductance technique was used to measure passivation quality. Little degradation in the effective lifetime and implicit open circuit voltage of these devices (< 20 mV) was observed in all cases. It is especially remarkable that for big uniform pyramids, the open-circuit voltage is comparable to the values obtained on flat substrates.

Kuumalanka-anemometri virtausmittauksissa

Tässä työssä selostetaan kuumalanka-anemometrin käyttö virtausmittauksissa. Kuumalanka-anemometrilla saadaan mitattua virtausnopeuden ja -suunnan lisäksi nopeusheilahteluja. Mittaustaajuus on tyypillisesti useita kymmeniä tuhansia mittauksia sekunnissa ja signaali on jatkuva. Nykytekniikalla pystytään helposti tallentamaan mittauslaitteistolta saatu viesti tietokoneelle ja muuntamaan se nopeudeksi. Hetkellisten nopeuksien avulla voidaan laskea turbulenttisen virtauksen ominaisuuksia, kuten turbulenssin intensiteetti ja spektri. Kuumalanka-anemometrissa lämmitetään sähköisesti ohutta lankaa, joka on mitattavassa virtauksessa. Langan sähköteho on suunnilleen yhtäsuuri kuin langasta konvektiolla siirtyvä lämpöteho. Tällöin on teoreettisesti mahdollista laskea virtausnopeus lämpötehosta lämmönsiirtokorrelaatioilla. Käytännössä laitteisto joudutaan kuitenkin erikseen kalibroimaan, mutta sähkötehon teoreettista riippuvuutta konvektiosta käytetään hyväksi. Kuumalangan lämmitettävä osuus on tyypillisesti halkaisijaltaan 5 µm ja pituudeltaan noin 1 mm. Sitä käytetään pääasiassa kaasuvirtausten mittaamiseen ja valtaosassa mittauksissa virtausaineena on ilma. Kuumalanka voi olla toteutettu kuumakalvotekniikalla, jossa halkaisijaltaan noin 50 - 70 µm paksuinen kuitu on päällystetty ohuella sähköä johtavalla kalvolla. Kuumakalvoanturin ei tarvitse olla muodoltaan sylinterimäinen, se voi olla mm. kartiomainen tai kiilamainen. Erikoispäällystetyllä kuumakalvoanturilla on mahdollista mitata myös nestevirtauksia. Mitattaessa kaasuvirtauksia kuumakalvon etuna on selvästi parempi kestävyys verrattuna kuumalankaan. Nimitystä kuumalanka-anemometri käytetään yleisesti molemmista anturityypeistä Tämän työn alussa käsitellään sylinterin yli tapahtuvaan virtaukseen liittyvää virtausmekaniikkaa ja lämmönsiirtoa. Anemometrin sähköinen osa, laitteisto ja sen kalibrointi käydään läpi. Langan suuntariippuvuuden laskentaan esitetään tarvittavat yhtälöt. Työssä esitellään kolme laitteistolla tehtyä perusmittausta: anturin kohtauskulman muuttaminen, pyörähdyssymmerisen suihkun nopeuskenttä ja tuulitunnelin rajakerros. Lisäksi esitellään yksi käytännöllinen ja vaativampi mittaus, jossa on mitattu nopeusprofiili radiaalikompressorin diffuusorin loppuosassa.

Väsyttävästi kuormitettujen hitsattujen rakenteiden suunnittelukäytännön kehittäminen

Hitsatuilla rakenteilla väsyminen on keskeinen vauriotekijä. Väsymiskestoiän laskentaan on olemassa useita erilaisia menetelmiä, joista hot spot ﷓menetelmä on hitsattujen rakenteiden yhteydessä yhä yleistyvä ja sangen käyttökelpoinen. Hot spot menetelmässä kestoikälaskenta perustuu rakenteellisen jännityksen vaihteluun ja pieneen joukkoon kokeellisesti määrättyjä Wöhler-käyriä. Rakenteellinen jännitys voidaan määrittää joko prototyypistä mittaamalla, elementtimenetelmällä laskemalla tai parametristen kerrointen avulla. Suunnittelukäytännön kehittämisessä tutkittiin esimerkkirakenteena Rammer RC 22 leikkurimurskainta. Tarkoituksena oli mitata murskaimesta voimasuureita, joita voitaisiin käyttää kuormitustietona laskettaessa jännityksiä elementtimenetelmällä. Myöhempien laskentatulosten verifiointia varten mitattiin lisäksi muutamia hot spot ﷓jännityksiä. Työn kokeellinen puoli keskittyi voimasuuremittauksiin ja niistä saatavien tulosten saattamiseen sopusointuun vapaakappalemallien kanssa. Suoritettiin lukuisia kalibrointimittauksia ja mittausjärjestelyä kehitettiin, kunnes syyt aluksi saatujen mittaustulosten virheellisyyteen selvisivät. Leikkausvoimamittausten osalta tuloksia verifioitiin elementtimenetelmälaskelmin. Työn tuloksena saatiin luotua toimiva pohja voimasuure- ja hot spot ﷓mittauksille. Jatkossa voidaan siirtyä tekemään mittauksia todellisissa työskentelytilanteissa.

Control of doped layers in p-i-n microcrystalline solar cells fully deposited with HWCVD

In this paper, the influence of the deposition conditions on the performance of p-i-n microcrystalline silicon solar cells completely deposited by hot-wire chemical vapor deposition is studied. With this aim, the role of the doping concentration, the substrate temperature of the p-type layer and of amorphous silicon buffer layers between the p/i and i/n microcrystalline layers is investigated. Best results are found when the p-type layer is deposited at a substrate temperature of 125 °C. The dependence seen of the cell performance on the thickness of the i layer evidenced that the efficiency of our devices is still limited by the recombination within this layer, which is probably due to the charge of donor centers most likely related to oxygen.

Top-gate microcrystalline silicon TFTs processed at low temperature (<200ºC)

N-type as well P-type top-gate microcrystalline silicon thin film transistors (TFTs) are fabricated on glass substrates at a maximum temperature of 200 °C. The active layer is an undoped μc-Si film, 200 nm thick, deposited by Hot-Wire Chemical Vapor. The drain and source regions are highly phosphorus (N-type TFTs) or boron (P-type TFTs)-doped μc-films deposited by HW-CVD. The gate insulator is a silicon dioxide film deposited by RF sputtering. Al-SiO 2-N type c-Si structures using this insulator present low flat-band voltage,-0.2 V, and low density of states at the interface D it=6.4×10 10 eV -1 cm -2. High field effect mobility, 25 cm 2/V s for electrons and 1.1 cm 2/V s for holes, is obtained. These values are very high, particularly the hole mobility that was never reached previously.

Technological solution for the automatic replacement of the catalytic filaments in HWCVD

The degradation of the catalytic filaments is the main factor limiting the industrial implementation of the hot wire chemical vapor deposition (HWCVD) technique. Up to now, no solution has been found to protect the catalytic filaments used in HWCVD without compromising their catalytic activity. Probably, the definitive solution relies on the automatic replacement of the catalytic filaments. In this work, the results of the validation tests of a new apparatus for the automatic replacement of the catalytic filaments are reported. The functionalities of the different parts have been validated using a 0.2 mm diameter tungsten filament under uc-Si:H deposition conditions.

Trolley R&D project for a small portal log yard crane

This master’s thesis was done for Andritz Inc. Atlanta Georgia. The purpose of the thesis was to develop a new trolley for a small portal log yard crane. In the beginning of the thesis the basic principles of the systematic design processes have been described, along which the design work of the trolley has proceeded. The second literature part consists of the design and dimensioning of the welded steel structures under fatigue loading. The design work of the trolley consists of the engineering and the selection of the mechanical components and the design of the load carrying structure for the trolley. The realization of the steel structure of the trolley is based on the fatigue and static dimensioning. The fatigue dimensioning is grounded in the life expectations estimated for the trolley and the static dimensioning is based on the CMAA guidelines. The computer aided element method was utilized in the design of the steel structure. The effective notch method and the hot spot method were used in the fatigue calculations. The trolley structure was carried out by using the sheet metal parts in order to manufacture the structure as effective and low cost way as possible. The corner stone of the dimensioning of the trolley structure was the utilization of the open profiles made of welded or cold formed sheet metals, which provide better weldability, weld inspection, access for repairs and corrosion protection. As a last part of the thesis a new trolley traveling system was developed. The distribution of the wheel loads of the trolley bogies on the main girder was also studied, which led to an innovative suspension arrangement between the trolley leg and the bogie. The new bogie solution increases the service life of the main girder of the crane and improves the stability of the bogies. The outcome of the thesis is an excellent trolley structure from the weight and the service life point of view.