Cellulosic Films Obtained from the Treatment of Sugarcane Bagasse Fibers with N-methylmorpholine-N-oxide (NMMO)

Ethanol/water organosolv pulping was used to obtain sugarcane bagasse pulp that was bleached with sodium chlorite. This bleached pulp was used to obtain cellulosic films that were further evaluated by Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). A good film formation was observed when temperature of 74 degrees C and baths of distilled water were used, which after FTIR, TGA, and SEM analysis indicated no significant difference between the reaction times. The results showed this to be an interesting and promising process, combining the prerequisites for a more efficient utilization of agro-industrial residues.

Cellulose modified fibres in cement based composites

The objective of the present work is to evaluate the effect of surface modification of cellulose pulp fibres on the mechanical and microstructure of fibre-cement composites. Surface modification of the cellulose pulps was performed with Methacryloxypropyltri-methoxysilane (MPTS) and Aminopropyltri-ethoxysilane (APTS) in an attempt to improve their durability into fibre-cement composites. The surface modification showed significant influence on the microstructure of the composites on the fibre-matrix interface and in the mineralization of the fibre lumen as seen by scanning electron microscopy (SEM) with back-scattered electron (BSE) detector. Accelerated ageing cycles decreased modulus of rupture (MOR) and toughness (TE) of the composites. Composites reinforced with MPTS-modified fibres presented fibres free from cement hydration products, while APTS-modified fibres presented accelerated mineralization. Higher mineralization of the fibres led to higher embrittlement of the composite after accelerated ageing cycles. These observations are therefore very useful for understanding the mechanisms of degradation of fibre-cement composites. (C) 2009 Elsevier Ltd. All rights reserved.

Effect of fibre morphology on flocculation of fibre-cement suspensions

The objective of the present research was to evaluate the effect of fibre morphology (e.g., length, width, fibrillation, broken ends, content of fines and number of fibres per gram) on flocculation and drainage properties of fibre-cement suspensions and on physical properties of the fibre-cement composites. Mechanical refining was used to change the morphological properties of Eucalyptus and Pinus pulps. Results show that the mechanical refining increased the size of the formed flocs and decreased the concentration of free small particles (with dimensions between 1 and 20 pm) as a consequence of the increased fibrillation and content of fines, which increased the capacity of the fibres to capture the mineral particles. High levels of refining were necessary for Pinus pulp to obtain cement retention values similar to those obtained by unrefined Eucalyptus pulp. This is due to the higher number of fibres per gram in Eucalyptus pulp than in Pinus pulp. Pulp refining improved the packing of the particles and, although decreased the drainage rate. it contributed to a less porous structure, which improved the microstructure of the composite. (C) 2009 Elsevier Ltd. All rights reserved.

Hygroexpansivity profiles on a commercial paper machine

Paper products show dimensional changes when subjected to moisture content modification. Hygroexpansivity was investigated in a commercial paper machine operating at 1256 m/min by a set of measurements on 75 g/m(2) reprographic bleached eucalyptus pulp paper samples. The present work shows hygroexpansivity development in different sections of the paper machine along the manufacturing direction. The measurement results demonstrate the effects of papermaking process operations on paper hygroexpansivity and lead to the confirmation of fiber orientation degree, drying restraint and shrinkage and paper tension as significant influencing factors. Structural, strength and elastic properties of paper were also measured as a function of machine direction position and presented for discussion purposes.

Ripening-associated changes in the amounts of starch and non-starch polysaccharides and their contributions to fruit softening in three banana cultivars

BACKGROUND: Fruit softening is generally attributed to cell wall degradation in the majority of fruits. However, unripe bananas contain a large amount of starch, and different banana cultivars vary in the amount of starch remaining in ripe fruits. Since studies on changes in pulp firmness carried outwith bananas are usually inconclusive, the cell wall carbohydrates and the levels of starch and soluble cell wall monosaccharides from the pulps of three banana cultivars were analysed at different ripening stages. RESULTS: Softening of Nanicao and Mysore bananas seemed to be more closely related to starch levels than to cell wall changes. For the plantain Terra, cell wall polysaccharide solubilisation and starch degradation appeared to be the main contributors. CONCLUSION: Banana softening is a consequence of starch degradation and the accumulation of soluble sugars in a cultivar-dependent manner. However, contributions from cell wall-related changes cannot be disregarded. (C) 2011 Society of Chemical Industry

Diabetes induces metabolic alterations in dental pulp

Diabetes can interfere in tissue nutrition and can impair dental pulp metabolism. This disease causes oxidative stress in cells and tissues. However, little is known about the antioxidant system in the dental pulp of diabetics. Thus, it would be of importance to study this system in this tissue in order to verify possible alterations indicative of oxidative stress. The aim of this study was to evaluate some parameters of antioxidant system of the dental pulp of healthy (n = 8) and diabetic rats (n = 8). Diabetes was induced by streptozotocin in rats. Six weeks after diabetes induction, a pool of the dental pulp of the 4 incisors of each rat (healthy and diabetic) was used for the determination of total protein and sialic acid concentrations and catalase and peroxidase activities. Data were compared by a Student t test (p <= 0.05). Dental pulps from both groups presented similar total protein concentrations and peroxidase activity. Dental pulps of diabetic rats exhibited significantly lower free, conjugated, and total sialic acid concentrations than those of control tissues. Catalase activity in diabetic dental pulps was significantly enhanced in comparison with that of control pulps. The result of the present study is indicative of oxidative stress in the dental pulp caused by diabetes. The increase of catalase activity and the reduction of sialic acid could be resultant of reactive oxygen species production.

Evaluation of two mineral trioxide aggregate compounds as pulp-capping agents in human teeth

The present randomized, controlled prospective study evaluated the histomorphological response of human dental pulps capped with two grey mineral trioxide aggregate (MTA) compounds. Pulp exposures were performed on the occlusal floor of 40 human permanent pre-molars. The pulp was capped either with ProRoot (Dentsply) or MTA-Angelus (Angelus) and restored with zinc oxide eugenol cement. After 30 and 60 days, teeth were extracted and processed for histological examination and the effects on the pulp were scored. The data were subjected to Kruskal-Wallis and Conover tests (alpha = 0.05). In five out of the 40 teeth bacteria were present in pulp tissue. No significant difference was observed between the two materials (P > 0.05) in terms of overall histological features (hard tissue bridge, inflammatory response, giant cells and particles of capping materials). Overall, 94% and 88% of the specimens capped with MTA-Angelus and ProRoot, respectively, showed either total or partial hard tissue bridge formation (P > 0.05). Both commercial materials ProRoot (Dentsply) and MTA-Angelus (Angelus) produced similar responses in the pulp when used for pulp capping in intact, caries-free teeth.

Cytotoxic effects and pulpal response caused by a mineral trioxide aggregate formulation and calcium hydroxide

Purpose: To evaluate: the in vivo pulpal response after pulpotomy with different capping agents. In addition, the in vitro cytotoxic effects of both materials were assessed by applying them on culture of pulp cells. Methods: For the in vivo test, the coronal pulp of 28 teeth of dogs was mechanically removed and the root pulps were capped with the following dental materials: Group 1: Pro-Root NITA (PRMTA); and Group 2 (control): calcium hydroxide saline paste (CH). After 60 days, the animals were sacrificed and the teeth processed for histological analysis. In the in vitro test, experimental extracts obtained from both capping agents were applied on the cultured MDPC-23 odontoblast-like cells. Results: In the root pulps capped with PRMTA or CH, coagulation necrosis partially replaced by dystrophic calcification as well as tubular dentin matrix laid down by elongated pulp cells was observed. None or mild inflammatory response occurred beneath the capped pulpal wound. Regarding the pulpal response, PRMTA and CH presented no statistical difference. However, the teeth capped CH presented greater healthy pulp loss which resulted in convex shape of the hard barrier than PRMTA. When applied on the cultured cells, it was demonstrated that PRMTA and CH solutions decreased the cell metabolic activity by 9.9% and 29.4%, respectively. CH caused higher cytotoxic effects to the MDPC-23 cells as well as deeper healthy pulp tissue loss than PRMTA. However, similar sequence of healing occurred after pulpotomy with both dental materials.

Reactivity of syringyl and guaiacyl lignin units and delignification kinetics in the kraft pulping of eucalyptus globulus wood using Py-Gc-Ms/FID

Eucalyptus globulus sapwood and heartwood showed no differences in lignin content (23.0% vs. 23.7%) and composition: syringyl-lignin (17.9% vs. 18.0%) and guaiacyl-lignin (4.8% vs. 5.2%). Delignification kinetics of S- and G-units in heartwood and sapwood was investigated by Py-GC–MS/FID at 130, 150 and 170 °C and modeled as double first-order reactions. Reactivity differences between S and G-units were small during the main pulping phase and the higher reactivity of S over G units was better expressed in the later pulping stage. The residual lignin composition in pulps was different from wood or from samples in the initial delignification stages, with more G and H-units. S/G ratio ranged from 3 to 4.5 when pulp residual lignin was higher than 10%, decreasing rapidly to less than 1. The S/H was initially around 20 (until 15% residual lignin), decreasing to 4 when residual lignin was about 3%.

Aplicação de celulases e xilanases na reciclagem de fibras de papel

Tese de Doutoramento em Engenharia Química e Biológica (área de conhecimento em Engenharia Enzimática e das Fermentações)

Extraction and characterization of polysaccharides from non-traditional Brazilian Amazon sources

[Excerpt] Cupuassu (Theobroma grandiflorum), tucumã (Astrocaryum aculeatum), peach palm (Bactris gasipaes) and abricó (American Mammea L.) are exotic fruits found in the Brazilian Amazon rainforest. All of them are well known by the native populations, and for centuries the pulps have been used in the production of juices, deserts, jams, syrups, and alcoholic beverages, among others. Additionally, the fruit seeds have been used as animal feed, fertilizers or to plant new seedlings, but a great part of these seeds are usually discarded. (...)

Molecular mass distribution of materials solubilized by xylanase treatment of Douglas-Fir kraft pulp

Irgazyme, a commercial xylanase preparation from Trichoderma longibrachiatum, and xylanase D a purified enzyme from Trichoderma harzianum E58 were tested for their ability to enhance peroxide bleaching of Douglas-fir (Pseudotsuga menziesii) kraft pulp. A treatment with Irgazyme caused a much larger increase in brightness than did xylanase D. A double xylanase treatment with Irgazyme, before and after peroxide bleaching, resulted in the highest final brightness. Alkaline extraction increased the brightness of Douglas-fir brownstock. Treatment with Irgazyme released more lignin and carbohydrates than did xylanase D. The molecular mass of the lignin extracted from Irgazyme-treated brownstock was much larger than that from the control pulp. The lignin-like macromolecules directly solubilized from peroxide bleached pulps were substantially larger than those solubilized from the brownstock, irrespective of whether they were produced during xylanase or control treatments. This indicates that different kinds of materials were solubilized when a xylanase treatment was applied at different points in the bleaching sequence and raises concerns about the role of lignin entrapment in the mechanism by which xylanase enhances peroxide bleaching.

Estudos sôbre a alimentação mineral do cafeeiro, X: extração de macronutrientes na colheita pelas variedades "Mundo Novo", "Caturra" e "Bourbon Amarelo"

This paper deals with the determination of the content of macronutrients in pulp and beans of three coffee varieties, namely 'Mundo Novo', 'Caturra Amarelo' and 'Bourbon Amarelo'. Samples were collected in plantations located in the three types of soils herein most of S. Paulo, Brazil, coffee is grown, that is, "terra roxa legítima" (Ribeirão Preto), "massapé-salmourão" (Mocóca), and "arenito de Bauru" (Pindorama). The following main conclusions were drawn after statistical analysis of data obtained hereby. There is no statistical difference among the three varieties . Average contents of macronutrients, as per cent of the dry matter, are the following: N P K Ca Mg S bean 1,71 0,10 1,53 0,27 0,15 0,12 pulps 1.78 0,14 3,75 0,41 0,13 0,15 Samples collected in Mocóca ("massapé-salmourão") had lower N and K contents, probably due to lack of availability of these elements in the soil, as suggested by its analysis. Results obtained in this work are in good agreement with data described elsewhere. Out of the total of elements contained in the whole fruit the following proportions are exported as clean coffee: N - 2/3, P and K - 1/2, Ca, Mg and S - 1/3. It is clear therefore that a substantial amount of elements absorbed from the soil remains in the pulp or in the dry hulls which result from processing. From this fact raises the interest of using these residues as fertilizer in the coffee plantations.

Ripening and quality of 'Laetitia' plums following harvest and cold storage as affected by inhibition of ethylene action

The inhibition of ethylene action by 1-methylcyclopropene (1-MCP) extends shelf and storage life of many climacteric fruits. However, 1-MCP appears to have limited effects on stone fruit depending on specie and cultivar. The effects of 1-MCP on ripening and quality of 'Laetitia' plums were determined during ripening at 23ºC following harvest and cold storage. Japanese plums (Prunus salicina, cv. Laetitia) were harvested at mature pre-climacteric stage, cooled to 2ºC within 36 hours of harvest and then treated with 0, 0.05, 0.10, 0.50 or 1.00 muL L-1 of 1-MCP at 1°C for 24 hours. Following treatment, fruits were either held at 23ºC for 16 days or stored at 1ºC for 50 days. Fruits were removed from cold storage at 10-day intervals and allowed to ripe at 23°C for five days. A delay of climacteric respiration and ethylene production by 1-MCP treatment during ripening following harvest and cold storage was associated to a slow rate of fruit softening. 1-MCP treatment also delayed the loss of titratable acidity and changes of flesh and skin color, whereas it had little or no effect on soluble solids content. 1-MCP effects were concentration- and storage duration-dependent and, generally, a saturation fruit response to 1-MCP occurred between 0.5 and 1.0 muL L-1. During ripening, 1-MCP treated fruits attained quality similar to that of controls. Results indicated that 1-MCP treatment may extend shelf life (23ºC) and storage life (1ºC) of 'Laetitia' plums by approximately six and 20 days, respectively.

Kosteuden ja lämpötilan vaikutus kartonkimassojen muovattavuuteen

Työn tavoitteena oli kartoittaa yleisesti kartongin valmistukseen käytettävien massatyyppien muovattavuuspotentaali. Muovattuvuuteen eniten vaikuttava tekijänä pidettiinmassojen murtovenymää. Työssä tutkittiin kosteuden ja lämpötilan sekä vetonopeuden vaikutusta mekaanisten ja sellumassojen ominaisuuksiin laboratorio-olosuhteissa. Kirjallisuusosassa tarkastellaan paperin lasisiirtymälämpötilaa muovauksen kannalta oleellisena tekijä. Lisäksi käydään läpi tapoja, joilla murtovenymää voidaan kasvattaa. Kartongin keskikerroksen aallotuksessa ja valmistettaessa paperipohjaisia tuotteita syvävedolla, käytetään hyväksi paperin pehmenemistä lämpötilan ja kosteuden alaisena. Niiden olosuhteita tarkastellaan lyhyesti. Lisäksi luodaan katsaus lämpötilan, kosteuden ja nopeuden vaikutuksistapaperin mekaanisiin ominaisuuksiin. Työn kokeellisessa osassa massojen mekaanisia ominaisuuksia testattiin erilaisissa kosteuspitoisuuksissasekä lämpötiloissa eri vetonopeuksilla. Kokeiden perusteella pyrittiin löytämään olosuhteet kullekin massalle, joissa niillä on paras murtovenymä. Lisäksi selvitettiin kuidun kihartamisen, sellumassojen jauhatuksen sekä arkin vapaan kuivumisen vaikutusta murtovenymään. Erilaiset massat saavuttavat parhaan murtovenymän erilaisissa kosteus- ja lämpötilaolosuhteissa. Sellumassoilla paras murtovenymä saadaan huoneenlämpötilassa ja paperin kosteuspitoisuuden ollessa välillä 11...12%. CTMP-massojen paras murtovenymä saadaan vedellä kyllästetyllä paperilla kohotetussa lämpötilassa. Lämpötila riippuu CTMP-massan valmistustavasta ja raaka-aineesta. Sellumassoilla on parempi kokonaisvenymä, kuin ligniinipitoisilla massoilla. Vetonopeuden vaikutus murtovenymään riippuu massasta sekä kosteudesta. Alhaisessa kosteudessa suurempi vetonopeus antaa aina pienemmän venymän. Kosteuden noustessa riippuu massasta, miten vetonopeus vaikuttaa murtovenymään. Plastinen osa tietystä venymästä on riippumaton massasta, jauhatusasteesta ja kuivatustavasta. Ainut vaikuttava muuttuja on kosteus. Kosteuden kasvu kasvattaa plastista venymää.