Dynamics of energy transfer and frequency upconversion in Tm3+ doped fluoroindate glass

The spectroscopic properties of Tm3+-doped fluoroindate glasses (FIG) were described by single wavelength pumping in the red region. The Judd-Ofelt (J-O) theory was used to obtain the quantum efficiency of the 4f-4f transitions and other spectroscopic parameters. The dynamics of the fluorescence was investigated and energy transfer (ET) processes among Tm3+ ions were studied. The results indicate that a two-step one-photon absorption process is responsible for the ultraviolet upconversion (UC) emissions, and dipole-dipole interaction provides the main contribution for ET rate is equal to the decay rate of noninteracting among active ions.

Structure and properties of Ti4+-Ureasil organic-inorganic hybrids

Hybrid planar waveguides were prepared from Ti4+-acetylacetone (acac)-Ureasil sols deposited on glass substrates. Structural features have been investigated by spectroscopic measurements (Fourier Transform Infrared Spectroscopy (FTIR), X-ray Photoelectron Spectroscopy (XPS) and Raman scattering) and Small Angle X-ray Scattering (SAXS). Addition of Ti 4+-acac to the ureasil (Ti:Si molar ratio 1:1) leads to the formation of bonds between the Ti complex and the siloxane groups, whereas further addition of Ti4+ (Ti:Si molar ratio 5:1) leads to the additional formation of titanium-rich nanoclusters. The optical parameters of the waveguides such as refractive index, thickness, propagating modes and attenuation coefficient were measured at 632.8, 543.5 and 1550 nm by the prism coupling technique. The refractive index can be tuned by the Ti4+ relative content. The few microns thick planar waveguides support well confined propagating modes with low attenuation loss for all compositions. ©2006 Sociedade Brasileira de Química.

Growth and morphology of eumelanin thin films - A future bioelectronic material?

We present a study on the thin film morphology and the optical properties of eumelanin resulting from different synthesis routes: the oxidation of tyrosine with hydrogen peroxide, the auto-oxidation of dihydroxyphenylanaline in water and its auto-oxidation in dimethyl sulfoxid. Atomic Force Microscopy images indicate that the presence of holes and particles depends on the eumelanin synthesis route and the substrate employed. Smooth films with very few defects could be obtained with eumelanin synthesized in dimethyl sulfoxide deposited on glass substrates. Our study shows that all eumelanin preparations are comparable in terms of thin film morphology on the submicrometer scale and UV-visible transmission properties. ©The Electrochemical Society.

Effects of dentin dry/moist condition on the immediate adhesive performance of different solvent-based etch-and-rinse adhesivesystems

Purpose: The purpose of this research was to analyze and measure, under optical microscopy, the hybrid layer thickness and resin tags length, as well as the microtensile bond strength of two conventional adhesive systems when applied to dry and moist dentinal substrate. Methods: Thirty-two extracted human molars were randomly distributed into four groups according to the adhesive systems (XP Bond and Prime&Bond 2.1) and moisture condition (dry and moist). In Groups I and II, XP adhesive system was applied on dry and moist dentin, respectively; while Groups III and IV received PB adhesive system, in the same way as was done in Groups I and II, respectively. After adhesive and restorative procedures, all specimens were sectioned along their long axes; one hemi-tooth sample was subjected to the microtensile bond strength test while the other was decalcified and serially sectioned into six micron thick slices and sequentially mounted on glass slides. These sections were stained by the Brown and Brenn method for posterior analysis and measurement of the hybrid layer and resin tags under a light microscope with a micrometric ocular 40/075. Results: Data were analyzed using two-way ANOVA and Tukey's test (α=0.05). For the variable hybrid layer thickness, XP showed no significant differences between dry and moist dentin (5.2 μm and 5.5 μm, respectively), but for PB, hybrid layer was significantly thicker for moist (4.0 μm) than for dry dentin (3.0 μm). For the variable resin tags length XP showed 17.9 μm length for dry dentin and 20.8 μm for moist dentin; PB 11.7 μm for dry and 12.69 μm for moist dentin;there was no significant differences between them, independent of the moisture condition. For the variable microtensile bond strength, XP showed 38.0 MPa for dry dentin and 44.5 MPa for moist dentin; and PB showed 22.7 MPa for dry dentin and 20.8 MPa for dry dentin no significant difference was observed between moist and dry dentin for XP (p=0.2) and PB (p=0.7), but XP was presented significantly higher bond strength values than PB in both moisture conditions (p=0.003 for dry and p=0.002 for moist). Conclusion: The two-step butanol-based etch-and-rinse adhesive XP Bond presented a superior behavior with regard to the hybrid layer thickness, length of resin tags and bond strength to dry and moist dentin substrates when compared with two-step acetone-based adhesive system Prime&Bond2.1. © 2013 Elsevier Ltd.

Structural transition of ZnO thin films produced by RF magnetron sputtering at low temperatures

Zinc oxide (ZnO) thin films were prepared using reactive radio-frequency magnetron sputtering of a pure metallic zinc target onto glass substrates. The evolution of the surface morphology and the optical properties of the films were studied as a function of the substrate temperature, which was varied from 50 to 250 C. The surface topography of the samples was examined using atomic force microscopy (AFM), and their optical properties were studied via transmittance measurements in the UV-Vis-NIR region. DRX and AFM analyses showed that the surface morphology undergoes a structural transition at substrate temperatures of around 150 C. Actually, at 50 C the formation of small grains was observed while at 250 C the grains observed were larger and had more irregular shapes. The optical gap remained constant at ∼3.3 eV for all films. In the visible region, the average optical transmittance was 80 %. From these results, one can conclude that the morphological properties of the ZnO thin films were more greatly affected by the substrate temperature, due to mis-orientation of polycrystalline grains, than were the optical properties. © 2013 Springer Science+Business Media New York.

Investigação de propriedades de filmes finos de Al2O3 para aplicação em dispositivos eletrônicos

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Estudo da fotossensibilidade de materiais híbridos de sílica dopados com heteropoliânions de tungstênio

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Propriedades químicas e ópticas de filmes de carbono amorfo halogenados produzidos por deposição a vapor químico assistido por plasma (PECVD) e deposição e implantação iônica por imersão em plasma (DIIIP)

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Síntese e caracterização de filmes finos de óxido de zinco

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito da pressão em filmes finos de ZnO:Al por RF Magnetron sputtering reativo

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Propriedades ópticas e elétricas de materiais híbridos de sílica/orgânico à base de GPTS:TEOS preparados pelo método sol-gel

Fabrication of optoelectronic devices requires the employment of at least one transparent electrode. Usually, commercially transparent electrodes have been made by deposition of indium tin oxide (ITO) films by RF-Sputtering technique. These commercial electrodes have sheet resistance of about 100 Ω/sq and optical transmittance of 77% at the wavelength of 550 nm. The poly(3,4-ethylenedioxythiophene):polystyrene-sulfonate (PEDOT:PSS) is an alternative material to fabricate transparent electrodes due to its high conductivity (about 600 S/cm) and solubility in water. Soluble conductive materials exhibits advantages for processing of electrode layers, however there is a disadvantage during devices fabrication once materials with the same solvent of the electrode material cannot be coated one over the other. Alternatively, organic/Silica hybrid materials prepared by sol-gel process allow producing bulks and films with high chemical durability. In order to obtain transparent electrodes with high chemical durability, we introduced a blended material comprising the high UV-VIS transparency of organic/Silica sol-gel material and a high conductivity polymer PEDOT:PSS. The organic/Silica sol was obtained using two different molar concentrations (1:1 and 4:1), of tetraethylorthosilicate (TEOS) and 3-glycidoxypropyltrimethoxysilane (GPTS). Amounts of PEDOT:PSS solutions were added to the sol material, resulting in different weight fractions of sol and polymer. G:T/P:P were deposit onto glass substrates by spray-coating. In order to perform electrical characterization of the blended material, gold electrodes were thermally evaporated onto the films. The electrical characterization was performed using a Keithley 2410 source/meter unity and the optical characterization, using a Cary50 UV-Vis spectrophotometer. The absorption coefficient and electric conductivity of the different compositions blends, as function of the PEDOT:PSS concentration, were...

Síntese e caracterização de alvo de óxido de zinco dopado com alumínio

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Liquid crystal polymer brushes and their application as alignment layers in liquid crystal cells

Liquid Crystal Polymer Brushes and their Application as Alignment Layers in Liquid Crystal Cells Polymer brushes with liquid crystalline (LC) side chains were synthesized on planar glass substrates and their nematic textures were investigated. The LC polymers consist of an acrylate or a methacrylate main chain and a phenyl benzoate group as the mesogenic unit which is connected to the main chain via a flexible alkyl spacer composed of six CH2 units. The preparation of the LC polymer brushes was carried out according to the “grafting from” technique: polymerization is carried out from azo-initiators that have been previously self-assembled on the substrate. LC polymer brushes with a thickness from a few nm to 230 nm were synthesized by varying the monomer concentration and the polymerization time. The LC polymer brushes were thick enough to allow for direct observation of the nematic textures with a polarizing microscope. The LC polymer brushes grown on untreated glass substrates exhibited irregular textures (“polydomains”). The domain size is in the range of some micrometers and depends only weakly on the brush thickness. The investigations on the texture-temperature relationship of the LC brushes revealed that the brushes exhibit a surface memory effect, that is, the identical texture reappears after the LC brush sample has experienced a thermal isotropization or a solvent treatment, at which the nematic LC state has been completely destroyed. The surface memory effect is attributed to a strong anchoring of the orientation of the mesogenic units to heterogeneities at the substrate surface. The exact nature of the surface heterogeneities is unknown. The effect was observed for the LC brushes swollen with low molecular weight nematic molecules, as well. Rubbing the glass substrate with a piece of velvet cloth prior to the surface modification with the initiator and the brush growth gives rise to the formation of homogenous alignment of the mesogenic units in the LC polymer side chains. Monodomain textures were obtained for these LC brushes. The mechanism for the homogeneous alignment is based on the transfer of Nylon fibers during the rubbing process. A surfactant was mixed with the azo-initiator in modifying rubbed substrates for subsequent brush generation. Such brushes exhibited biaxial optical properties. Hybrid LC cells made from a substrate modified with biaxial brushes and a rubbed glass substrate show an orientation with a tilt angle of a = –15.6 . This work shows that LC brushes grown on rubbed surfaces fulfill the important criteria for alignment layers: the formation of macroscopic monodomains. First results indicate that by diluting the brush with molecules which are also covalently bound to the surface but induce a different orientation, a system is obtained in which the two conflicting alignment mechanisms can be used to generate a tilted alignment. In order to allow for an application of the alignment layers into a potential product, subsequent work should focus on the questions how easy and in which range the tilt angle can be controlled.

Size-selective investigations of spectral and emission properties of small particles and nanotubes

In dieser Arbeit wurde die Elektronenemission von Nanopartikeln auf Oberflächen mittels spektroskopischen Photoelektronenmikroskopie untersucht. Speziell wurden metallische Nanocluster untersucht, als selbstorganisierte Ensembles auf Silizium oder Glassubstraten, sowie ferner ein Metall-Chalcogenid (MoS2) Nanoröhren-Prototyp auf Silizium. Der Hauptteil der Untersuchungen war auf die Wechselwirkung von fs-Laserstrahlung mit den Nanopartikeln konzentriert. Die Energie der Lichtquanten war kleiner als die Austrittsarbeit der untersuchten Proben, so dass Ein-Photonen-Photoemission ausgeschlossen werden konnte. Unsere Untersuchungen zeigten, dass ausgehend von einem kontinuierlichen Metallfilm bis hin zu Clusterfilmen ein anderer Emissionsmechanismus konkurrierend zur Multiphotonen-Photoemission auftritt und für kleine Cluster zu dominieren beginnt. Die Natur dieses neuen Mechanismus` wurde durch verschiedenartige Experimente untersucht. Der Übergang von einem kontinuierlichen zu einem Nanopartikelfilm ist begleitet von einer Zunahme des Emissionsstroms von mehr als eine Größenordnung. Die Photoemissions-Intensität wächst mit abnehmender zeitlicher Breite des Laserpulses, aber diese Abhängigkeit wird weniger steil mit sinkender Partikelgröße. Die experimentellen Resultate wurden durch verschiedene Elektronenemissions-Mechanismen erklärt, z.B. Multiphotonen-Photoemission (nPPE), thermionische Emission und thermisch unterstützte nPPE sowie optische Feldemission. Der erste Mechanismus überwiegt für kontinuierliche Filme und Partikel mit Größen oberhalb von mehreren zehn Nanometern, der zweite und dritte für Filme von Nanopartikeln von einer Größe von wenigen Nanometern. Die mikrospektroskopischen Messungen bestätigten den 2PPE-Emissionsmechanismus von dünnen Silberfilmen bei „blauer“ Laseranregung (hν=375-425nm). Das Einsetzen des Ferminiveaus ist relativ scharf und verschiebt sich um 2hν, wenn die Quantenenergie erhöht wird, wogegen es bei „roter“ Laseranregung (hν=750-850nm) deutlich verbreitert ist. Es zeigte sich, dass mit zunehmender Laserleistung die Ausbeute von niederenergetischen Elektronen schwächer zunimmt als die Ausbeute von höherenergetischen Elektronen nahe der Fermikante in einem Spektrum. Das ist ein klarer Hinweis auf eine Koexistenz verschiedener Emissionsmechanismen in einem Spektrum. Um die Größenabhängigkeit des Emissionsverhaltens theoretisch zu verstehen, wurde ein statistischer Zugang zur Lichtabsorption kleiner Metallpartikel abgeleitet und diskutiert. Die Elektronenemissionseigenschaften bei Laseranregung wurden in zusätzlichen Untersuchungen mit einer anderen Anregungsart verglichen, der Passage eines Tunnelstroms durch einen Metall-Clusterfilm nahe der Perkolationsschwelle. Die elektrischen und Emissionseigenschaften von stromtragenden Silberclusterfilmen, welche in einer schmalen Lücke (5-25 µm Breite) zwischen Silberkontakten auf einem Isolator hergestellt wurden, wurden zum ersten Mal mit einem Emissions-Elektronenmikroskop (EEM) untersucht. Die Elektronenemission beginnt im nicht-Ohmschen Bereich der Leitungsstrom-Spannungskurve des Clusterfilms. Wir untersuchten das Verhalten eines einzigen Emissionszentrums im EEM. Es zeigte sich, dass die Emissionszentren in einem stromleitenden Silberclusterfilm Punktquellen für Elektronen sind, welche hohe Emissions-Stromdichten (mehr als 100 A/cm2) tragen können. Die Breite der Energieverteilung der Elektronen von einem einzelnen Emissionszentrum wurde auf etwa 0.5-0.6 eV abgeschätzt. Als Emissionsmechanismus wird die thermionische Emission von dem „steady-state“ heißen Elektronengas in stromdurchflossenen metallischen Partikeln vorgeschlagen. Größenselektierte, einzelne auf Si-Substraten deponierte MoS2-Nanoröhren wurden mit einer Flugzeit-basierten Zweiphotonen-Photoemissions-Spektromikroskopie untersucht. Die Nanoröhren-Spektren wiesen bei fs-Laser Anregung eine erstaunlich hohe Emissionsintensität auf, deutlich höher als die SiOx Substratoberfläche. Dagegen waren die Röhren unsichtbar bei VUV-Anregung bei hν=21.2 eV. Eine ab-initio-Rechnung für einen MoS2-Slab erklärt die hohe Intensität durch eine hohe Dichte freier intermediärer Zustände beim Zweiphotonen-Übergang bei hν=3.1 eV.

Diseño y fabricación de dispositivos basados en cristal líquido polimérico

Esta tesis se centra en el estudio y desarrollo de dispositivos de aplicación basados en cristal líquido polimérico. Las propiedades de los cristales líquidos los hacen interesantes para su uso en el desarrollo de dispositivos de seguridad para autenticación de productos y marcas, y detección y prevención de falsificaciones. Asimismo, pueden ser muy útiles para fabricar dispositivos basados en CLs dispersos en polímero, los cuales tienen a su vez múltiples aplicaciones. La orientación de las moléculas de cristal líquido y la birrefringencia son las dos características principales que afectan a las propiedades de estos dispositivos. Un dispositivo de cristal líquido estándar consiste en un sándwich formado por dos sustratos de vidrio transparente, dotados con electrodo de ITO (Indium Tin Oxide) en su superficie interna, que confinan el cristal líquido en su interior. En la primera parte de esta tesis se describen las características más importantes que describen una célula de cristal líquido. Esta introducción básica en necesaria para la correcta comprensión de los capítulos posteriores en los que se detalla el desarrollo concreto de los dispositivos desarrollados en la investigación llevada a cabo. Por ejemplo, en el caso de los dispositivos de seguridad se han eliminado los sustratos de vidrio (en la última fase de su desarrollo) para conseguir dispositivos flexibles. En la segunda parte de la tesis se incluye la descripción completa de los dispositivos fabricados, así como de los protocolos de fabricación seguidos y diseñados específicamente para ello. También se detallan en esta parte los resultados obtenidos, así como las propiedades ópticas y electroópticas en cada caso, y el/los equipos de caracterización utilizados. Utilizando cristal líquido nemático y colorante dicroico, se han desarrollado dispositivos que contienen múltiples imágenes latentes en cada cara del mismo. Utilizando distintas técnicas de alineamiento se consigue crear cualquier tipo de motivo latente, ya sean símbolos sencillos, figuras, logotipos o incluso imágenes con escala de gris. Cuanto más complejo es el dispositivo, mayor es la dificultad para reproducirlo en una eventual falsificación. Para visualizar e identificar los motivos es necesario emplear luz polarizada, por ejemplo, con la ayuda de un sencillo polarizador lineal. Dependiendo de si el polarizador está colocado delante del dispositivo o detrás del él, se mostrarán las imágenes generadas en una u otra cara. Este efecto es posible gracias al colorante dicroico añadido al CL, a la orientación inducida sobre las moléculas, y a la estructura de twist utilizada en los dispositivos. En realidad, para ver el efecto de los dispositivos no es necesario el uso de un polarizador, basta con el reflejo de una superficie dielétrica (percialmente polarizado), o la luz emitida por la pantalla de dispositivos de consumo comunes como un televisor LCD, un monitor de ordenador o un “smartphone”. Por otro lado, utilizando una mezcla entre un CL nemático polimérico y un CL nemático no polimérico es posible fabricar dispositivos LCPC (Liquid Crystal Polymer Composite) con propiedades electroópticas muy interesantes, que funcionan a tensiones de conmutación bajas. El CL polimérico conforma una estructura de red en el interior del sándwich que mantiene confinado al CL nemático en pequeños microdominios. Se han fabricado dispositivos LCPC con conmutación inversa utilizando tanto alineamiento homogéneo como homeotrópico. Debido a que tanto la estructura de CL polimérico como el CL nemático que rellena los microdominios están orientados en una misma dirección de alineamiento preinducida, la luz dispersada por el dispositivo se encuentra polarizada. La dirección de polarización coincide con la dirección de alineamiento. La innovación aportada por esta investigación: un nuevo dispositivo LCPC inverso de respuesta ultrarápida y polarizada basado en la mezcla de dos CL nemáticos y, un dispositivo de seguridad y autenticación, patentado internacionalmente, basado en CL nemáticos dopados con colorante dicroico. Abstract This thesis is centered on the availability to use polymerizable liquid crystals to develop non-display application LC devices. Liquid crystal properties make them useful for the development of security devices in applications of authentication and detection of fakes, and also to achieve polymer dispersed LC devices to be used for different applications that will be studied here. Induced orientation of liquid crystal molecules and birefringence are the two main properties used in these devices. A standard liquid crystal device is a sandwich consisting of two parallel glass substrates carrying a thin transparent ITO (Indium‐Tin‐Oxide) electrode on their inner surfaces with the liquid crystal in the middle. The first part of this thesis will describe the most important parameters describing a liquid crystal cell. This basis is necessary for the understanding of later chapters where models of the liquid crystal devices will be discussed and developed. In the case of security devices the standard structure of an LC device has been modified by eliminating the glass substrates in order to achieve plastic and flexible devices. The second part of the thesis includes a detailed description of the devices achieved and the manufacturing protocols that have been developed ad-hoc. The optical and electrooptical properties and the characterization equipment are described here as well. Employing nematic liquid crystal and dichroic colorants, we have developed devices that show, with the aid of a polarizer, multiple images on each side of the device. By different alignment techniques it is possible to create any kind of symbols, drawings or motifs with a grayscale; the more complex the created device is, the more difficult is to fake it. To identify the motifs it is necessary to use polarized light. Depending on whether the polarizer is located in front of the LC cell or behind it, different motifs from one or the other substrate are shown. The effect arises from the dopant color dye added to the liquid crystal, the induced orientation and the twist structure. In practice, a grazing reflection on a dielectric surface is polarized enough to see the effect. Any LC flat panel display (LCD TV, computer, mobile phone) can obviously be used as backlight as well. On the other hand, by using a mixture of polymerizable and non-polymerizable nematics liquid crystals it is also possible to achieve LCPC (Liquid Crystal Polymer Composite) devices that show really interesting electrooptical characteristics using low switching voltages. Polymerizable LC creates a hollow structure inside the sandwich glass cell that keep nematics liquid crystal confined creating microdomains. Homogeneous and homeotropic alignments have been used to develop inverse switching mode LCPCs. Due to the double LC oriented structure, the outgoing scattered light from these devices is already polarized. The polarization axis coincides with LC molecules director, the alignment direction promoted. The novelties derived from the investigation presented here, new ultrafast inverse LCPC with polarized outgoing scattered light based on oriented nematic LC mixture, and an internationally patented security and authentication device based on nematics (doped with dichroic dye) oriented polymerizable LC.