The "reversed" treatment approach for synchronous liver metastases and colorectal cancer. Feasability and first results

Background: The « reversed treatment» approach inverts the treatment sequence of¦advanced synchronous colorectal liver metastases - i.e. the liver metastasis is¦treated first, followed by resection of the primary tumor. Chemotherapy is performed¦before and after liver surgery. We recently started to use a reversed treatment¦approach in selected patients. The aim of this study is to critically assess this new¦treatment modality.¦Methods: Nine patients (7 male, 2 female, mean age 62 years) benefited from this¦new treatment between November 2008 and May 2010. The data were collected¦retrospectively.¦Results: All patients responded to the neoadjuvant chemotherapy. The median¦number of liver metastases was 6 (range 1 - 22). The median size of the largest liver¦metastases was 4.3 cm (range 2.6 - 13 cm). Three patients had portal vein¦embolization prior to liver surgery. Two patients could not complete the treatment.¦One had to undergo emergency surgery for occluding colonic tumor. The second one¦showed liver recurrence before starting the adjuvant chemotherapy. The seven¦patients who completed the treatment are still alive after a median time of 27 months¦(range 17 - 37 months). Seven of them had recurrence (1 rectal, 6 liver). The median¦disease-free survival was 9 months (range 0 - 17 months).¦Conclusion: Based on our preliminary experiences, the reversed strategy shows¦encouraging results for the treatment of advanced synchronous colorectal liver¦metastases in well selected patients. The treatment was generally well tolerated and¦long term survival seems to be prolonged.

Cardiac and pericardial fistulae associated with esophageal or gastric neoplasms: a literature review

Pericardial and cardiac fistulae secondary to esophageal or gastric tumors are considered exceptional. They have never been the object of a literature review. We reviewed the medical literature between 1881 and 2001, searching for all published cases of pericardial or cardiac fistulae developed from esophageal and gastric tumors or favored by the applied therapy to these tumors. The cases of metastasization, tumor spread, and neoplasic pericardial effusion without fistula were excluded. Fifty patients were identified, with one original case. More than half the cases (56%) occurred in the last 25 years. Substernal pain is the main symptom. The majority of patients present at least one condition favoring fistula formation. The auscultation of a water-wheel murmur may suggest a pneumopericardium and therefore a pericardial fistula, as does a purulent pericarditis. Arrhythmias, signs of ischemia, and hematemesis point toward a ventricular fistula. Neurological and hemostasis disorders may be suspect of an atrial lesion. Diagnosis should be made by the association of a scanner and a transit. Prognosis is bad: 76% of the patients die in the first month. Pericardial or cardiac fistulae are part of the differential diagnosis of thoracic pain in patients with esophageal or gastric tumors and in patients who were treated for these pathologies. The diagnosis must be as quick as possible. An operation (patients with a good prognosis) or the placement of a stent (patients with a bad prognosis) is the only chance of survival

Whole-body vibration training: metabolic cost of synchronous, side-alternating or no vibrations.

Whole-body vibration training improves strength and can increase maximal oxygen consumption ([·V]O(2max)). No study has compared the metabolic demand of synchronous and side-alternating whole-body vibration. We measured [·V]O₂ and heart rate during a typical synchronous or side-alternating whole-body vibration session in 10 young female sedentary participants. The 20-min session consisted of three sets of six 45-s exercises, with 15 s recovery between exercises. Three conditions were randomly tested on separate days: synchronous at 35 Hz and 4 mm amplitude, side-alternating at 26 Hz and 7.5 mm amplitude (peak acceleration matched at 20 g in both vibration conditions), and no vibrations. Mean [·V]O₂ (expressed as %[·V]O(2max)) did not differ between conditions: 29.7 ± 4.2%, 32.4 ± 6.5%, and 28.7 ± 6.7% for synchronous, side-alternating, and no vibrations respectively (P = 0.103). Mean heart rate (% maximal heart rate) was 65.6 ± 7.3%, 69.8 ± 7.9%, and 64.7 ± 5.6% for synchronous, side-alternating, and no vibrations respectively, with the side-alternating vibrations being significantly higher (P = 0.019). When analysing changes over exercise sessions, mean [·V]O₂ was higher for side-alternating (P < 0.001) than for synchronous and no vibrations. In conclusion, side-alternating whole-body vibration elicits higher heart rate responses than synchronous or no vibrations, and could elevate [·V]O₂, provided the session lasts more than 20 min.

A synchronous, middle early Aptian age for the demise of the Helvetic Urgonian platform related to the unfolding oceanic anoxic event 1a ("Selli event")

Un âge synchrone (partie moyenne de l'Aptien inférieur) de l'ennoiement de la plate-forme Urgonienne helvétique en relation avec l'événement océanique anoxique 1a ("événement Selli"). - La fin de la plate-forme urgonienne, calibrée par analyse des isotopes stables du carbone sur roche totale et par biostratigraphie basée sur les ammonites, est datée du milieu de l'Aptien inférieur (Près de la limite des zones weissi et deshayesi). Cet arrêt, synchrone dans des coupes représentatives du domaine helvétique alpin, est un événement environemental majeur renregistré en France, en Espagne, au Protugal, en Oman, au Mexique et dans le domaine Pacifique. En tenant compte des limites de résolution de la biostatrigraphie et des autres techniques de datation, cet épisode semble également être synchrone à l'échelle globale. Pour beaucoup d'auteurs, la disparition de récifs de coraux et de rudistes corrélée à la fin de la sédimentation urgonienne correspond à la mise en place de conditions anoxiques à l'Aptien inférieur. Celles-ci caractérisent un événement d'importance global: l'événement anoxique OAE 1a.

High constant incidence rates of second primary neoplasms

The incidence of contralateral breast cancer is high and constant with age, around five per 1000 women who had a primary breast cancer. For other neoplasms, the pattern of incidence of second primary neoplasms with age is less known, particularly as for only a few neoplasms the site of origin is not totally removed, and hence remains at risk of a second primary. Using the dataset from the Cancer Registry of the Swiss Canton of Vaud, we show that the incidence of second neoplasms is constant with age also after oral and pharyngeal, colorectal cancers, cutaneous malignant melanoma (CMM) and basal cell carcinoma. The incidence of first primary oral and pharyngeal cancer increased 20-fold between age 30-39 and 70-89 years, whereas the incidence of second neoplasms did not increase with age. Rates of second colorectal cancer remained relatively constant with age, between 2.5 per 1000 at age 40-59 years and 3.8 per 1000 at 70 years and above. Likewise, for CMM, the age-specific incidence rates of second primary CMM did not vary, ranging between 1 and 2.5 per 1000 in various subsequent age groups. The pattern of incidence for second basal cell carcinoma was similar, with no clear rise with age. These patterns are compatible with the occurrence of a single mutational event in a population of susceptible individuals. A possible implication of these observations is that a variable, but potentially large, proportion of cancers arise in very high-risk individuals and the incidence, on average, increases at a high constant level at a predetermined age.

Deoxyribonucleic acid content as an indicator of progression of squamous cell carcinogenesis in the esophagus: comparative analysis on imprint-cytospin and tissue section preparation.

BACKGROUND: The purpose of this study was to explore the potential use of image analysis on tissue sections preparation as a predictive marker of early malignant changes during squamous cell (SC) carcinogenesis in the esophagus. Results of DNA ploidy quantification on formalin-fixed, paraffin-embedded tissue using two different techniques were compared: imprint-cytospin and 6 microm thick tissue sections preparation. METHODS: This retrospective study included 26 surgical specimens of squamous cell carcinoma (SCC) from patients who underwent surgery alone at the Department of Surgery in CHUV Hospital in Lausanne between January 1993 and December 2000. We analyzed 53 samples of healthy tissue, 43 tumors and 7 lymph node metastases. RESULTS: Diploid DNA histogram patterns were observed in all histologically healthy tissues, either distant or proximal to the lesion. Aneuploidy was observed in 34 (79%) of 43 carcinomas, namely 24 (75%) of 32 early squamous cell carcinomas and 10 (91%) of 11 advanced carcinomas. DNA content was similar in the different tumor stages, whether patients presented with single or multiple synchronous tumors. All lymph node metastases had similar DNA content as their primary tumor. CONCLUSIONS: Early malignant changes in the esophagus are associated with alteration in DNA content, and aneuploidy tends to correlate with progression of invasive SCC. A very good correlation between imprint-cytospin and tissue section analysis was observed. Although each method used here showed advantages and disadvantages; tissue sections preparation provided useful information on aberrant cell-cycle regulation and helped select the optimal treatment for the individual patient along with consideration of other clinical parameters.

Prognosis in Duke's B colorectal carcinoma: the Jass classification revisited.

OBJECTIVE: To assess whether Jass staging enhances prognostic prediction in Dukes' B colorectal carcinoma. DESIGN: A historical cohort observational study. SETTING: A university tertiary care centre, Switzerland. SUBJECTS: 108 consecutive patients. INTERVENTIONS: Curative resection of Dukes' B colorectal carcinoma between January 1985 and December 1988, Patients with familial adenomatous polyposis; hereditary non-polyposis colorectal cancer; Crohns' disease; ulcerative colitis and synchronous and recurrent tumours were excluded. A comparable group of 155 consecutive patients with Dukes' C carcinoma were included for reference purposes. MAIN OUTCOME MEASURES: Disease free and overall survival for Dukes' B and overall survival for Dukes' C tumours. RESULTS: Dukes' B tumours in Jass group III or with an infiltrated margin had a significantly worse disease-free survival (p = 0.001 and 0.0001, respectively) and those with infiltrated margins had a significantly worse overall survival (p = 0.002). Overall survival among those with Dukes' B Jass III and Dukes' B with infiltrated margins was no better than overall survival among all patients with Dukes' C tumours. CONCLUSION: Jass staging and the nature of the margin of invasion allow patients undergoing curative surgery for Dukes' B colorectal carcinoma to be separated into prognostic groups. A group of patients with Dukes' B tumours whose prognosis is inseparable from those with Dukes' C tumours can be identified, the nature of the margin of invasion being used to classify a larger number of patients.

Toward Synchronous Extensible Dependency Grammar

Extensible Dependency Grammar (XDG; Debusmann, 2007) is a flexible, modular dependency grammarframework in which sentence analyses consist of multigraphs and processing takes the form of constraint satisfaction. This paper shows how XDGlends itself to grammar-driven machine translation and introduces the machinery necessary for synchronous XDG. Since the approach relies on a shared semantics, it resembles interlingua MT.It differs in that there are no separateanalysis and generation phases. Rather, translation consists of the simultaneousanalysis and generation of a single source-target sentence.

Error probability in synchronous digital circuits due to power supply noise

This paper presents a probabilistic approach to model the problem of power supply voltage fluctuations. Error probability calculations are shown for some 90-nm technology digital circuits.The analysis here considered gives the timing violation error probability as a new design quality factor in front of conventional techniques that assume the full perfection of the circuit. The evaluation of the error bound can be useful for new design paradigms where retry and self-recoveringtechniques are being applied to the design of high performance processors. The method here described allows to evaluate the performance of these techniques by means of calculating the expected error probability in terms of power supply distribution quality.

Synchronous Digital Hierarchy implementation to a Radio Transmission Node

Kiristyville markkinoille on aina tuotava jotain uutta tarjottavaa ja SDH-kortti on yksi sellainen tuote jonka Nokia Networks julkistaa osaksi uutta Nokia Flexihub Nodea. Tavoitteena on suunnitella VC-12kanavoitu STM-1 kortti yhdistämään ylemmän tason tietoliikenneverkko suuren kapasiteetin radioon. Ennen kuin markkinoilla on valmis tuote, on sen takana valtaisa määrä työtä. Erilaisia dokumentteja on pitänyt tuottaa ja sopimuksia tehdä. Esimerkiksi vaatimusmäärittelyt on oltava selvät, jotta tiedetään mitä tuotteelta halutaan. Tätä ennen on kuitenkin pitänyt ymmärtää miten SDHtoimii ja miten otsikkotavuja käsitellään. Myös erilaiset piirivalinnat aiheuttavat miettimistä, sillä markkinoilla on runsaasti valmiita piirejä SDH signaalinkäsittelyyn. Varma tiedonsiirto on tärkeää puhelinoperaattorille ja siksi joudutaan miettimään varmennuksia ja niiden toteuttamista. Myös synkronointi on tärkeä osa SDH järjestelmää ja sen toteuttaminen hyvin on tärkeää. Hälytykset on otettava huomioon ja mietittävä, miten niiden käsittely saadaan hoidettua järkevästi, ilman että mikään järjestelmän osa ruuhkautuu kohtuuttomasti. Tässä Diplomityössä on tutustuttu SDH-järjestelmään, otsikkotavujen käsittelyyn ja vaatimusmäärittelyihin.

Measuring the effects through time of the influence of visuomotor and visuotactile synchronous stimulation on a virtual body ownership illusion

Previous studies have examined the experience of owning a virtual surrogate body or body part through specific combinations of cross-modal multisensory stimulation. Both visuomotor (VM) and visuotactile (VT) synchronous stimulation have been shown to be important for inducing a body ownership illusion, each tested separately or both in combination. In this study we compared the relative importance of these two cross-modal correlations, when both are provided in the same immersive virtual reality setup and the same experiment. We systematically manipulated VT and VM contingencies in order to assess their relative role and mutual interaction. Moreover, we present a new method for measuring the induced body ownership illusion through time, by recording reports of breaks in the illusion of ownership ("breaks") throughout the experimental phase. The balance of the evidence, from both questionnaires and analysis of the breaks, suggests that while VM synchronous stimulation contributes the greatest to the attainment of the illusion, a disruption of either (through asynchronous stimulation) contributes equally to the probability of a break in the illusion.

Direct-on-line axial flux permanent magnet synchronous generator static and dynamic performance

In distributed energy production, permanent magnet synchronous generators (PMSG) are often connected to the grid via frequency converters, such as voltage source line converters. The price of the converter may constitute a large part of the costs of a generating set. Some of the permanent magnet synchronous generators with converters and traditional separately excited synchronous generators couldbe replaced by direct-on-line (DOL) non-controlled PMSGs. Small directly networkconnected generators are likely to have large markets in the area of distributed electric energy generation. Typical prime movers could be windmills, watermills and internal combustion engines. DOL PMSGs could also be applied in island networks, such as ships and oil platforms. Also various back-up power generating systems could be carried out with DOL PMSGs. The benefits would be a lower priceof the generating set and the robustness and easy use of the system. The performance of DOL PMSGs is analyzed. The electricity distribution companies have regulations that constrain the design of the generators being connected to the grid. The general guidelines and recommendations are applied in the analysis. By analyzing the results produced by the simulation model for the permanent magnet machine, the guidelines for efficient damper winding parameters for DOL PMSGs are presented. The simulation model is used to simulate grid connections and load transients. The damper winding parameters are calculated by the finite element method (FEM) and determined from experimental measurements. Three-dimensional finite element analysis (3D FEA) is carried out. The results from the simulation model and 3D FEA are compared with practical measurements from two prototype axial flux permanent magnet generators provided with damper windings. The dimensioning of the damper winding parameters is case specific. The damper winding should be dimensioned based on the moment of inertia of the generating set. It is shown that the damper winding has optimal values to reach synchronous operation in the shortest period of time after transient operation. With optimal dimensioning, interferenceon the grid is minimized.

Fractional slot permanent magnet synchronous motors for low speed applications

This study compares different rotor structures of permanent magnet motors with fractional slot windings. The surface mounted magnet and the embedded magnet rotor structures are studied. This thesis analyses the characteristics of a concentrated two-layer winding, each coil of which is wound around one tooth and which has a number of slots per pole and per phase less than one (q < 1). Compared to the integer slot winding, the fractional winding (q < 1) has shorter end windings and this, thereby, makes space as well as manufacturing cost saving possible. Several possible ways of winding a fractional slot machine with slots per pole and per phase lessthan one are examined. The winding factor and the winding harmonic components are calculated. The benefits attainable from a machine with concentrated windingsare considered. Rotor structures with surface magnets, radially embedded magnets and embedded magnets in V-position are discussed. The finite element method isused to solve the main values of the motors. The waveform of the induced electro motive force, the no-load and rated load torque ripple as well as the dynamic behavior of the current driven and voltage driven motor are solved. The results obtained from different finite element analyses are given. A simple analytic method to calculate fractional slot machines is introduced and the values are compared to the values obtained with the finite element analysis. Several different fractional slot machines are first designed by using the simple analytical methodand then computed by using the finite element method. All the motors are of thesame 225-frame size, and have an approximately same amount of magnet material, a same rated torque demand and a 400 - 420 rpm speed. An analysis of the computation results gives new information on the character of fractional slot machines.A fractional slot prototype machine with number 0.4 for the slots per pole and per phase, 45 kW output power and 420 rpm speed is constructed to verify the calculations. The measurement and the finite element method results are found to beequal.

Permanent magnet synchronous motor for industrial inverter applications - analysis and design

During the latest few years the need for new motor types has grown, since both high efficiency and an accurate dynamic performance are demanded in industrial applications. For this reason, new effective control systems such as direct torque control (DTC) have been developed. Permanent magnet synchronous motors (PMSM) are well suitable for new adjustable speed AC inverter drives, because their efficiency and power factor are not depending on the pole pair number and speed to the same extent as it is the case in induction motors. Therefore, an induction motor (IM) with a mechanical gearbox can often be replaced with a direct PM motor drive. Space as well as costs will be saved, because the efficiency increases and the cost of maintenance decreases as well. This thesis deals with design criterion, analytical calculation and analysis of the permanent magnet synchronous motor for both sinusoidal air-gap flux density and rectangular air-gapflux density. It is examined how the air-gap flux, flux densities, inductances and torque can be estimated analytically for salient pole and non-salient pole motors. It has been sought by means of analytical calculations for the ultimate construction for machines rotating at relative low 300 rpm to 600 rpm speeds, which are suitable speeds e.g. in Pulp&Paper industry. The calculations are verified by using Finite Element calculations and by measuring of prototype motor. The prototype motor is a 45 kW, 600 rpm PMSM with buried V-magnets, which is a very appropriate construction for high torque motors with a high performance. With the purposebuilt prototype machine it is possible not only to verify the analytical calculations but also to show whether the 600 rpm PMSM can replace the 1500 rpm IM with a gear. It can also be tested if the outer dimensions of the PMSM may be the same as for the IM and if the PMSM in this case can produce a 2.5 fold torque, in consequence of which it may be possible to achieve the same power. The thesis also considers the question how to design a permanent magnet synchronous motor for relatively low speed applications that require a high motor torqueand efficiency as well as bearable costs of permanent magnet materials. It is shown how a selection of different parameters affects the motor properties. Key words: Permanent magnet synchronous motor, PMSM, surface magnets, buried magnets

Torque vibration model of axial-flux surface-mounted permanent magnet synchronous machine

In order that the radius and thus ununiform structure of the teeth and otherelectrical and magnetic parts of the machine may be taken into consideration the calculation of an axial flux permanent magnet machine is, conventionally, doneby means of 3D FEM-methods. This calculation procedure, however, requires a lotof time and computer recourses. This study proves that also analytical methods can be applied to perform the calculation successfully. The procedure of the analytical calculation can be summarized into following steps: first the magnet is divided into slices, which makes the calculation for each section individually, and then the parts are submitted to calculation of the final results. It is obvious that using this method can save a lot of designing and calculating time. Thecalculation program is designed to model the magnetic and electrical circuits of surface mounted axial flux permanent magnet synchronous machines in such a way, that it takes into account possible magnetic saturation of the iron parts. Theresult of the calculation is the torque of the motor including the vibrations. The motor geometry and the materials and either the torque or pole angle are defined and the motor can be fed with an arbitrary shape and amplitude of three-phase currents. There are no limits for the size and number of the pole pairs nor for many other factors. The calculation steps and the number of different sections of the magnet are selectable, but the calculation time is strongly depending on this. The results are compared to the measurements of real prototypes. The permanent magnet creates part of the flux in the magnetic circuit. The form and amplitude of the flux density in the air-gap depends on the geometry and material of the magnetic circuit, on the length of the air-gap and remanence flux density of the magnet. Slotting is taken into account by using the Carter factor in the slot opening area. The calculation is simple and fast if the shape of the magnetis a square and has no skew in relation to the stator slots. With a more complicated magnet shape the calculation has to be done in several sections. It is clear that according to the increasing number of sections also the result will become more accurate. In a radial flux motor all sections of the magnets create force with a same radius. In the case of an axial flux motor, each radial section creates force with a different radius and the torque is the sum of these. The magnetic circuit of the motor, consisting of the stator iron, rotor iron, air-gap, magnet and the slot, is modelled with a reluctance net, which considers the saturation of the iron. This means, that several iterations, in which the permeability is updated, has to be done in order to get final results. The motor torque is calculated using the instantaneous linkage flux and stator currents. Flux linkage is called the part of the flux that is created by the permanent magnets and the stator currents passing through the coils in stator teeth. The angle between this flux and the phase currents define the torque created by the magnetic circuit. Due to the winding structure of the stator and in order to limit the leakage flux the slot openings of the stator are normally not made of ferromagnetic material even though, in some cases, semimagnetic slot wedges are used. In the slot opening faces the flux enters the iron almost normally (tangentially with respect to the rotor flux) creating tangential forces in the rotor. This phenomenon iscalled cogging. The flux in the slot opening area on the different sides of theopening and in the different slot openings is not equal and so these forces do not compensate each other. In the calculation it is assumed that the flux entering the left side of the opening is the component left from the geometrical centre of the slot. This torque component together with the torque component calculated using the Lorenz force make the total torque of the motor. It is easy to assume that when all the magnet edges, where the derivative component of the magnet flux density is at its highest, enter the slot openings at the same time, this will have as a result a considerable cogging torque. To reduce the cogging torquethe magnet edges can be shaped so that they are not parallel to the stator slots, which is the common way to solve the problem. In doing so, the edge may be spread along the whole slot pitch and thus also the high derivative component willbe spread to occur equally along the rotation. Besides forming the magnets theymay also be placed somewhat asymmetric on the rotor surface. The asymmetric distribution can be made in many different ways. All the magnets may have a different deflection of the symmetrical centre point or they can be for example shiftedin pairs. There are some factors that limit the deflection. The first is that the magnets cannot overlap. The magnet shape and the relative width compared to the pole define the deflection in this case. The other factor is that a shifting of the poles limits the maximum torque of the motor. If the edges of adjacent magnets are very close to each other the leakage flux from one pole to the other increases reducing thus the air-gap magnetization. The asymmetric model needs some assumptions and simplifications in order to limit the size of the model and calculation time. The reluctance net is made for symmetric distribution. If the magnets are distributed asymmetrically the flux in the different pole pairs will not be exactly the same. Therefore, the assumption that the flux flows from the edges of the model to the next pole pairs, in the calculation model from one edgeto the other, is not correct. If it were wished for that this fact should be considered in multi-pole pair machines, this would mean that all the poles, in other words the whole machine, should be modelled in reluctance net. The error resulting from this wrong assumption is, nevertheless, irrelevant.