Inhibition by poly(acrylic acid) and morphological changes in calcium carbonate and calcium carbonate/calcium sulfate crystallization on silica fibers

An intrinsic exposed core optical fiber sensor (IECOFS) made from fused silica was used to monitor the crystallization of calcium carbonate (CaCO3) and CaCO3/calcium sulfate (CaSO4) composite at 100 and 120 °C in the absence and presence of low-molar-mass (Mn ≤ 2000) poly(acrylic acid) (PAA) with different end groups. The IECOFS responded only to deposition and growth processes on the fiber surface rather than changes occurring in the bulk of the solution. Hexyl isobutyrate-terminated PAA (Mn = 1400) and hexadecyl isobutyrate-terminated PAA (Mn = 1700) were the most effective species in preventing CaCO3 deposition. Phase transformation from vaterite to aragonite/calcite decreased with increasing hydrophobicity of the PAA end group. Low-molar-mass PAA at 10 ppm showed very significant inhibition of CaCO3/CaSO4 composite formation for all end groups investigated.

A phase field study of morphological instabilities in multilayer thin films

We studied the microstructural evolution of multiple layers of elastically stiff films embedded in an elastically soft matrix using a phase field model. The coherent and planar film/matrix interfaces are rendered unstable by the elastic stresses due to a lattice parameter mismatch between the film and matrix phases, resulting in the break-up of the films into particles. With an increasing volume fraction of the stiff phase, the elastic interactions between neighbouring layers lead to: (i) interlayer correlations from an early stage; (ii) a longer wavelength for the maximally growing wave; and therefore (iii) a delayed break-LIP. Further, they promote a crossover in the mode of instability from a predominantly anti-symmetric (in phase) one to a symmetric (out of phase) one. We have computed a stability diagram for the most probable mode of break-up in terms of elastic modulus Mismatch and Volume fraction. We rationalize our results in terms of the initial driving force for destabilization, and corroborate our conclusions using simulations in elastically anisotropic systems.

On-Chip Clock Network Skew Measurement using Sub-Sampling

We present a technique for an all-digital on-chip delay measurement system to measure the skews in a clock distribution network. It uses the principle of sub-sampling. Measurements from a prototype fabricated in a 65 nm industrial process, indicate the ability to measure delays with a resolution of 0.5ps and a DNL of 1.2 ps.

Foot morphological difference between habitually shod and unshod runners

Foot morphology and function has received increasing attention from both biomechanics researchers and footwear manufacturers. In this study, 168 habitually unshod runners (90 males whose age, weight & height were 23 +/- 2.4years, 66 +/- 7.1kg & 1.68 +/- 0.13m and 78 females whose age, weight & height were 22 +/- 1.8years, 55 +/- 4.7kg & 1.6 +/- 0.11m) (Indians) and 196 shod runners (130 males whose age, weight & height were 24 +/- 2.6years, 66 +/- 8.2kg & 1.72 +/- 0.18m and 66 females whose age, weight & height were 23 +/- 1.5years, 54 +/- 5.6kg & 1.62 +/- 0.15m)(Chinese) participated in a foot scanning test using the easy-foot-scan (a three-dimensional foot scanning system) to obtain 3D foot surface data and 2D footprint imaging. Foot length, foot width, hallux angle and minimal distance from hallux to second toe were calculated to analyze foot morphological differences. This study found that significant differences exist between groups (shod Chinese and unshod Indians) for foot length (female p = 0.001), width (female p = 0.001), hallux angle (male and female p = 0.001) and the minimal distance (male and female p = 0.001) from hallux to second toe. This study suggests that significant differences in morphology between different ethnicities could be considered for future investigation of locomotion biomechanics characteristics between ethnicities and inform last shape and design so as to reduce injury risks and poor performance from mal-fit shoes.

Morphological structure of bismuth-doped n-type amorphous germanium sulphide semiconductors

Recent observation of n-type conduction in amorphous Ge20Ss_xBix at large bismuth concentrations (x = 11), which otherwise shows p-type conduction, has aroused considerable interest in the international scientific community [1]. The mechanism of such impurity incorporation in a germanium chalcogenide glass is not understood and is a topic of current interest. In our recent publications [2-10] we have brought to light some hitherto unknown and interesting features of bismuth dopants in chalcogen-rich Ge-X (X -- S, Se) glassy compositions. In this communication we present our new results of investigations on vitreous semiconductors Ge20S80 Bi using electron microscopy, electron diffraction of as-prepared and annealed/pressure quenched compositions. Our results provide conclusive support to the formation of composite clusters containing all the three elements, germanium, sulphur and bismuth, which crystallize in simpler stoichiometric compounds Bi2S3 and GeS2.

The Influence of Constantinople on Middle Byzantine Architecture (843-1204) : A typological and morphological approach at the provincial level.

The influence of the architecture of the Byzantine capital spread to the Mediterranean provinces with travelling masters and architects. In this study the architecture of the Constantinopolitan School has been detected on the basis of the typology of churches, completed by certain morphological aspects when necessary. The impact of the Constantinopolitan workshops appears to have been more important than previously realized. This research revealed that the Constantinopolitan composite domed inscribed-cross type or cross-in-square spread everywhere to the Balkans and it was assumed soon by the local schools of architecture. In addition, two novel variants were invented on the basis of this model: the semi-composite type and the so-called Athonite type. In the latter variant lateral conches, choroi, were added for liturgical reasons. Instead, the origin of the domed ambulatory church was partly provincial. One result of this study is that the origin of the Middle Byzantine domed octagonal types was traced to Constantinople. This is attested on the basis of the archaeological evidence. Also some other architectural elements that have not been preserved in the destroyed capital have survived at the provincial level: the domed hexagonal type, the multi-domed superstructure, the pseudo-octagon and the narthex known as the lite. The Constantinopolitan architecture during the period in question was based on the Early Christian and Late Antique forms, practices and innovations and this also emerges at the provincial level.

Morphological Characteristics of Genetically-Modified Pineapple Fruit

Genetic engineering is an attractive method for changing a single characteristic of ‘Smooth Cayenne’ pineapple, without altering its other desirable attributes. Techniques used in pineapple transformation, however, such as tissue culture and biolistic-mediated or Agrobacterium-mediated gene insertion are prone to somaclonal variation, resulting in the production of several morphological mutations (Smith et al., 2002). Fruit mutations can include distortion in fruit shape (round ball, conical, fan-shaped), reduced fruit size, multiple crowns, crownless fruit, fruitless crowns, and spiny crown leaves (Dalldorf, 1975; Sanewski et al., 1992). The present paper describes the variability in fruit-shape mutations between transgenic and non-transgenic fruit, and its subsequent impact on organoleptic characteristics.

Morphological transitions in polymer monolayers under compression

We present a systematic investigation of morphological transitions in poly vinylacetate Langmuir monolayers. On compression, the polymer monolayer is converted to a continuous membrane with a thickness of similar to 2-3 nm. Above a certain surface concentration the monolayer, on water, undergoes a morphological transition-buckling, leading to formation of striped patterns of period of lambda(b)similar to 160 nm, as determined from in situ grazing incidence small angle x-ray scattering measurements. The obtained value is much smaller than what has been typically observed for Langmuir monolayers on water or thin films on soft substrates. Using existing theories for buckling of fluidlike films on fluid substrates, we obtain very low values of bending rigidity and Young's modulus of the polymer monolayer compared to that observed earlier for lipid or polymeric monolayers. Since buckling in these monolayers occurs only above a certain surface concentration, we have looked at the possibility that the buckling in these films occurs due to changes in their mechanical properties under compression. Using the model of Huang and Suo of buckling of solidlike films on viscoelastic substrates, we find values of the mechanical properties, which are much closer to the bulk values but still significantly lower. Although the reduction could be along the lines of what has been observed earlier for ultrathin polymer film or surface layers of polymers, the possibility of micromechanical effects also determining the buckling in such polymer monolayers cannot be ruled out. We have provided possible explanation of the buckling of the poly vinylacetate monolayers in terms of the change in isothermal compression modulus with surface concentration.

Oesophagogastric ulceration in pigs: A visual morphological scoring guide

Objective: To provide a visual guide for oesophagogastric ulcer scoring and recognition of different morphological changes in the pars oesophagea. Design: Pig stomachs were collected at slaughter and visually evaluated and scored for parakeratosis, erosion and ulceration in the pars oesophagea. Results: A visual and descriptive guide is presented that will aid in the objective assessment and scoring of oesophagogastric ulceration in pigs within the pig health monitoring system (PHMS), namely to the four categories of 0 = normal stomach, 1 = parakeratosis and thickened epithelium, 2 = erosions and 3 = developed ulcers with and without stenosis. Conclusion: A visual guide has been developed that illustrates the full range of morphological changes that can occur in the pars oesophagea of the stomach within the few currently recognised stages of the disease.

Characterization of tree-to-tree variation in morphological, nutritional and medicinal properties of Canarium indicum nuts

As part of a feasibility study of the commercialization potential of C. indicum nuts as Agroforestry Tree Products in Papua New Guinea, preliminary characterization studies have examined the tree-to-tree variation in morphological traits (nut and kernel mass and kernel:nut ratio), as well as nutritional (carbohydrate, fat, protein, sodium, vitamin E) and medicinal traits (anti-oxidant activity, anti-inflammatory activity and phenolic content) of kernels from 18 to 72 trees in a small number of different villages of Papua New Guinea (East New Britain Province). There was continuous variation in these traits indicating opportunities for multiple trait cultivar development targeted at food and pharmaceutical markets. Certain traits, for example anti-inflammatory activity, in which tree-to-tree variation was highly significant, present greater opportunities than others, such as saturated:unsaturated fatty acid ratio. This intraspecific variation was greater within populations than between populations. The data presented has allowed the development of a strategy to domesticate C. indicum for cultivation in homegardens and cocoa-coconut agroforests, using a participatory approach aimed at the production of agroforestry tree products (AFTPs) to empower small-holders and enhance their livelihoods and income.

Using morphological traits to identify persistent lucernes for dryland agriculture in NSW, Australia

This paper reports on several studies conducted to better understand the variability between lucerne cultivars and lines, and use this to predict persistence in dryland grazing pastures in eastern Australia. Morphological traits of 20 cultivars/lines were measured in irrigated and dryland spaced plant experiments. Studies were also conducted to describe variation among lucernes in their utilisation of starch and responses to water deficit, pests and diseases. Multiple regression analyses were used to develop simple models where the measured traits could be used to predict persistence of lucerne lines in dryland evaluation experiments. Although there was significant variation among cultivars/lines in most measured traits, no single trait reliably predicted persistence of cultivars/lines in dryland evaluation experiments. However, variation in persistence at both sites could be explained by models developed by multiple regression using differences in the mean lengths of the longest stems at 10% flower in summer and winter. Persistent lucernes were those that had relatively long stems in summer and short stems in winter. Water use efficiencies, starch utilisation patterns and resistances to pests and diseases of different lucernes provided some improvement to this simple model, but these improvements were not consistent.

DNA markers linked to yield, yield components, and morphological traits in autotetraploid lucerne (Medicago sativa L.)

We have mapped and identified DNA markers linked to morphology, yield, and yield components of lucerne, using a backcross population derived from winter-active parents. The high-yielding and recurrent parent, D, produced individual markers that accounted for up to 18% of total yield over 6 harvests, at Gatton, south-eastern Queensland. The same marker, AC/TT8, was consistently identified at each individual harvest, and in individual harvests accounted for up to 26% of the phenotypic variation for yield. This marker was located in linkage group 2 of the D map, and several other markers positively associated with yield were consistently identified in this linkage group. Similarly, markers negatively associated with yield were consistently identified in the W116 map, W116 being the low-yielding parent. Highly significant positive correlations were observed between total yield and yield for harvests 1-6, and between total yield and stem length, tiller number, leaf yield/plant, leaf yield/5 stems, stem yield/plant, and stem yield/5 stems. Highly significant QTL were located for all these characters as well as for leaf shape and pubescence.

Morphological and developmental comparisons of seven greens quality hybrid bermudagrass (Cynodon dactylon (L.)Pers.x C transvaalensis Burtt-Davy

Fine-textured hybrid bermudagrass [Cynodon dactylon (L.) Pers. x C. transvaalensis Burtt-Davy] cultivars have been widely used for golf putting greens and lawn bowls greens in warm-climate areas for more than 40 years. During the past decade, the choice of cultivar for professional turfgrass managers has been expanded by a range of secondgeneration hybrid bermudagrasses, which differ from the first-generation cultivars ‘Tifgreen’ and ‘Tifdwarf ’ in their management requirements. In this paper, we present comparative morphological and developmental data for seven cultivars (Champion Dwarf, FloraDwarf, MS-Supreme, Novotek, Tifdwarf, TifEagle, Tifgreen) grown in spaced plant and sward experiments at Cleveland, Australia (27º32’S lat, 153º15’E long, 25 masl). The four ‘ultradwarf ’ cultivars (Champion Dwarf, MS-Supreme, FloraDwarf, TifEagle) showed slower vertical extension and produced fewer inflorescences than Tifdwarf, Tifgreen, and Novotek. However, in terms of the length of stolon internodes and their overall rate of lateral spread, Champion Dwarf, FloraDwarf, and TifEagle were comparable to Tifdwarf; MS-Supreme (with longer internodes) spread faster laterally, though slower than Tifgreen (which had the longest stolon internodes). In unmown swards, the four ultradwarfs produced shorter leaves than Tifgreen, Tifdwarf, and Novotek, but only Champion Dwarf produced significantly narrower leaves than Tifgreen, Tifdwarf, and Novotek, with TifEagle leaves also significantly narrower than those of Tifgreen and Novotek. Minimum threshold temperatures for growth were approximately 9° to 10°C (air temperature) and 15° to 16°C at 10 cm soil depth.

Morphological diversity of ruminal bacteriophages from sheep and cattle

Large numbers of bacteriophages (2 x 10(7) to 1 x 10(8)/ml) were present in ruminal fluid from sheep and cattle. Twenty-six distinct types were identified and placed in three morphological groups; several phages possessed unusual structural features. The large numbers and diversity of phages observed indicates a possible role in bacterial lysis and hence in the population dynamics of the ruminal bacteria.

Morphological and molecular diversity of Colletotrichum spp. causing pepper spot and anthracnose of lychee (Litchi chinensis) in Australia

Since the 1980s a new disease has been affecting Australian lychee. Pepper spot appears as small, black superficial lesions on fruit, leaves, petioles and pedicels and is caused by Colletotrichum gloeosporioides, the same fungus that causes postharvest anthracnose of lychee fruit. The aim of this study was to determine if a new genotype of C.gloeosporioides is responsible for the pepper spot symptom. Morphological assessments, arbitrarily-primed PCR (ap-PCR) and DNA sequencing studies did not differentiate isolates of C.gloeosporioides from anthracnose and pepper spot lesions. The ap-PCR identified 21 different genotypes of C.gloeosporioides, three of which were predominant. A specific genotype identified using ap-PCR was associated with the production of the teleomorph in culture. Analysis of sequence data of ITS and -tubulin regions of representative isolates did not group the lychee isolates into a monophyletic clade; however, given the majority of the isolates were from one of three genotypes found using ap-PCR, the possibility of a lychee specific group of C.gloeosporioides is discussed.