Self-mated tribological systems based on multilayer micro/nanocrystalline CVD diamond coatings

The tribological response of multilayer micro/nanocrystalline diamond coatings grown by the hot filament CVD technique is investigated. These multigrade systems were tailored to comprise a starting microcrystalline diamond (MCD) layer with high adhesion to a silicon nitride (Si3N4) ceramic substrate, and a top nanocrystalline diamond (NCD) layer with reduced surface roughness. Tribological tests were carried out with a reciprocating sliding configuration without lubrication. Such composite coatings exhibit a superior critical load before delamination (130–200 N), when compared to the mono- (60–100 N) and bilayer coatings (110 N), considering ∼10 µm thick films. Regarding the friction behaviour, a short-lived initial high friction coefficient was followed by low friction regimes (friction coefficients between 0.02 and 0.09) as a result of the polished surfaces tailored by the tribological solicitation. Very mild to mild wear regimes (wear coefficient values between 4.1×10−8 and 7.7×10−7 mm3 N−1 m−1) governed the wear performance of the self-mated multilayer coatings when subjected to high-load short-term tests (60–200 N; 2 h; 86 m) and medium-load endurance tests (60 N; 16 h; 691 m).

Adhesion and wear behaviour of NCD coatings on Si3N4 by micro-abrasion tests

Nanocrystalline diamond (NCD) coatings offer an excellent alternative for tribological applications, preserving most of the intrinsic mechanical properties of polycrystalline CVD diamond and adding to it an extreme surface smoothness. Silicon nitride (Si3N4) ceramics are reported to guarantee high adhesion levels to CVD microcrystalline diamond coatings, but the NCD adhesion to Si3N4 is not yet well established. Micro-abrasion tests are appropriate for evaluating the abrasive wear resistance of a given surface, but they also provide information on thin film/substrate interfacial resistance, i.e., film adhesion. In this study, a comparison is made between the behaviour of NCD films deposited by hot-filament chemical vapour deposition (HFCVD) and microwave plasma assisted chemical vapour deposition (MPCVD) techniques. Silicon nitride (Si3N4) ceramic discs were selected as substrates. The NCD depositions by HFCVD and MPCVD were carried out using H2–CH4 and H2–CH4–N2 gas mixtures, respectively. An adequate set of growth parameters was chosen for each CVD technique, resulting in NCD films having a final thickness of 5 m. A micro-abrasion tribometer was used, with 3 m diamond grit as the abrasive slurry element. Experiments were carried out at a constant rotational speed (80 r.p.m.) and by varying the applied load in the range of 0.25–0.75 N. The wear rate for MPCVD NCD (3.7±0.8 × 10−5 m3N−1m−1) is compatible with those reported for microcrystalline CVD diamond. The HFCVD films displayed poorer adhesion to the Si3N4 ceramic substrates than the MPCVD ones. However, the HFCVD films show better wear resistance as a result of their higher crystallinity according to the UV Raman data, despite evidencing premature adhesion failure.

Cellulose nanorods in liquid crystalline elastomers for improved actuators

Nanotechnology plays a central role in ‘tailoring’ materials’ properties and thus improving its performances for a wide range of applications. Coupling nature nano-objects with nanotechnology results in materials with enhanced functionalities. The main objective of this master thesis was the synthesis of nanocrystalline cellulose (NCCs) and its further incorporation in a cellulosic matrix, in order to produce a stimuli-responsive material to moisture. The induced behaviour (bending/unbending) of the samples was deeply investigated, in order to determine relationships between structure/properties. Using microcrystalline cellulose as a starting material, acid hydrolysis was performed and the NCC was obtained. Anisotropic aqueous solutions of HPC and NCC were prepared and films with thicknesses ranging from 22μm to 61μm were achieved, by using a shear casting technique. Microscopic and spectroscopic techniques as well as mechanical and rheological essays were used to characterize the transparent and flexible films produced. Upon the application of a stimulus (moisture), the bending/unbending response times were measured. The use of NCC allowed obtaining films with response times in the order of 6 seconds for the bending and 5 seconds for the unbending, improving the results previously reported. These promising results open new horizons for building up improved soft steam engines.

A Miocene mud volcano and its plumbing system: A chaotic complex revisited (Monferrato, NW Italy)

Chaotic deposits are frequently reported in the geological literature and are commonly interpreted as olistostromes or tectonic melanges. A chaotic complex in the Cenozoic succession of Monferrato (NW Italy) consists of interbedded mud breccia and burrowed silty clays that are pierced by sheared mud breccias and embed carbonate-cemented blocks. These may be represented by microcrystalline limestones or strongly cemented matrix-supported breccias locally containing remains of chemosymbiotic organisms (lucinid bivalves). Moreover, cylindrical concretions, up to 15 cm in diameter and 1 m long, occur in the chaotic complex and crosscut bedding planes at high angles. The cement of all these lithified portions is mainly dolomite characterized by low delta(13)C values (from -10.3 to -23parts per thousand PDB) and delta(18)O values up to + 7parts per thousand PDB. The delta(13)C values testify to precipitation of carbonates induced by microbial oxidation of methane, whereas the markedly positive delta(18)C signature, ubiquitous in the cylindrical concretions, is the evidence for the presence and destabilization of gas hydrates. The studied section provides a well-exposed example of the geological record of the birth, life, and death of a mud volcano. Unsheared, soft mud breccias represent mud flows along the flanks of the volcano, whereas sheared mud breccias are the result of the injection of unconsolidated overpressured fine-grained sediments, both taking place during ``eruptive'' phases. They were followed by more quiet stages of hemipelagic sedimentation, burrowing, and CH4 seeping. The cylindrical concretions represent the first described ancient example of the chimneys observed in present-day mud-volcano settings. They are the remnants of a cold-seep plumbing network that crosscut the mud volcano edifice. The chimneys were the pathway for the expulsion toward the sea floor of gas- and sediment-charged fluids likely originated from destabilization of methane gas hydrates. The association of mud breccias and methane-derived carbonates may not be due to mass gravity flows but can be primary and, therefore, is a diagnostic criterion for recognizing chaotic deposits due to mud volcano activity in the geological record.

Synthesis of triheptanoin and formulation as a solid diet for rodents

Triheptanoin-enriched diets have been successfully used in the experimental treatment of various metabolic disorders. Maximal therapeutic effect is achieved in the context of a ketogenic diet where triheptanoin oil provides 3040% of the daily caloric intake. However, pre-clinical studies using triheptanoin-rich diets are hindered by the difficulty of administering to laboratory animals as a solid foodstuff. In the present study, we successfully synthesized triheptanoin to the highest standards of purity from glycerol and heptanoic acid, using sulfonated charcoal as a catalyst. Triheptanoin oil was then formulated as a solid, stable and palatable preparation using a ketogenic base and a combination of four commercially available formulation agents: hydrophilic fumed silica, hydrophobic fumed silica, microcrystalline cellulose, and talc. Diet compliance and safety was tested on C57Bl/6 mice over a 15-week period, comparing overall status and body weight change. Practical applications: This work provides a complete description of (i) an efficient and cost-effective synthesis of triheptanoin and (ii) its formulation as a solid, stable, and palatable ketogenic diet (triheptanoin-rich; 39% of the caloric intake) for rodents. Triheptanoin-rich diets will be helpful on pre-clinical experiments testing the therapeutic efficacy of triheptanoin in different rodent models of human diseases. In addition, using the same solidification procedure, other oils could be incorporated into rodent ketogenic diet to study their dosage and long-term effects on mammal health and development. This approach could be extremely valuable as ketogenic diet is widely used clinically for epilepsy treatment.

Synthesis of triheptanoin and formulation as a solid diet for rodents

Triheptanoin-enriched diets have been successfully used in the experimental treatment of various metabolic disorders. Maximal therapeutic effect is achieved in the context of a ketogenic diet where triheptanoin oil provides 3040% of the daily caloric intake. However, pre-clinical studies using triheptanoin-rich diets are hindered by the difficulty of administering to laboratory animals as a solid foodstuff. In the present study, we successfully synthesized triheptanoin to the highest standards of purity from glycerol and heptanoic acid, using sulfonated charcoal as a catalyst. Triheptanoin oil was then formulated as a solid, stable and palatable preparation using a ketogenic base and a combination of four commercially available formulation agents: hydrophilic fumed silica, hydrophobic fumed silica, microcrystalline cellulose, and talc. Diet compliance and safety was tested on C57Bl/6 mice over a 15-week period, comparing overall status and body weight change. Practical applications: This work provides a complete description of (i) an efficient and cost-effective synthesis of triheptanoin and (ii) its formulation as a solid, stable, and palatable ketogenic diet (triheptanoin-rich; 39% of the caloric intake) for rodents. Triheptanoin-rich diets will be helpful on pre-clinical experiments testing the therapeutic efficacy of triheptanoin in different rodent models of human diseases. In addition, using the same solidification procedure, other oils could be incorporated into rodent ketogenic diet to study their dosage and long-term effects on mammal health and development. This approach could be extremely valuable as ketogenic diet is widely used clinically for epilepsy treatment.

Synthesis of triheptanoin and formulation as a solid diet for rodents

Triheptanoin-enriched diets have been successfully used in the experimental treatment of various metabolic disorders. Maximal therapeutic effect is achieved in the context of a ketogenic diet where triheptanoin oil provides 3040% of the daily caloric intake. However, pre-clinical studies using triheptanoin-rich diets are hindered by the difficulty of administering to laboratory animals as a solid foodstuff. In the present study, we successfully synthesized triheptanoin to the highest standards of purity from glycerol and heptanoic acid, using sulfonated charcoal as a catalyst. Triheptanoin oil was then formulated as a solid, stable and palatable preparation using a ketogenic base and a combination of four commercially available formulation agents: hydrophilic fumed silica, hydrophobic fumed silica, microcrystalline cellulose, and talc. Diet compliance and safety was tested on C57Bl/6 mice over a 15-week period, comparing overall status and body weight change. Practical applications: This work provides a complete description of (i) an efficient and cost-effective synthesis of triheptanoin and (ii) its formulation as a solid, stable, and palatable ketogenic diet (triheptanoin-rich; 39% of the caloric intake) for rodents. Triheptanoin-rich diets will be helpful on pre-clinical experiments testing the therapeutic efficacy of triheptanoin in different rodent models of human diseases. In addition, using the same solidification procedure, other oils could be incorporated into rodent ketogenic diet to study their dosage and long-term effects on mammal health and development. This approach could be extremely valuable as ketogenic diet is widely used clinically for epilepsy treatment.

Martensitic phase transformation in rapidly solidified Mn50Ni40In10 alloy ribbons

Heusler alloy Mn50Ni40In10 was produced as preferentially textured ribbon flakes by melt spinning, finding the existence of martensitic-austenic transformation with both phases exhibiting ferromagnetic ordering. A microcrystalline three-layered microstructure of ordered columnar grains grown perpendicularly to ribbon plane was formed between two thin layers of smaller grains. The characteristic temperatures of the martensitic transformation were MS=213 K, Mf=173 K, AS=222 K, and Af=243 K. Austenite phase shows a cubic L21 structure (a=0.6013(3) nm at 298 K and a Curie point of 311 K), transforming into a modulated fourteen-layer modulation monoclinic martensite

The use of micro-XRD for the study of glaze color decorations

The compounds responsible for the colours and decorations in glass and glazed ceramics include: colouring agents (transition metal ions), pigments (micro-and nano-precipitates of compounds that either do not dissolve or recrystallize in the glassy matrix) and opacifiers (microcrystalline compounds with high light scattering capability). Their composition, structure and range of stability are highly dependent not only on the composition but also on the procedures followed to obtain them. Chemical composition of the colorants and crystallites may be obtained by means of SEM-EDX and WDX. Synchrotron Radiation micro-X-ray Diffraction has a small beam size adequate (10 to 50 microns footprint size) to obtain the structural information of crystalline compounds and high brilliance, optimal for determining the crystallites even when present in low amounts. In addition, in glass decorations the crystallites often appear forming thin layers (from 10 to 100 micrometers thick) and they show a depth dependent composition and crystal structure. Their nature and distribution across the glass/glazes decorations gives direct information on the technology of production and stability and may be related to the color and appearance. A selection of glass and glaze coloring agents and decorations are studied by means of SR-micro- XRD and SEM-EDX including: manganese brown, antimony yellow, red copper lusters and cobalt blue. The selection includes Medieval (Islamic, and Hispano Moresque) and renaissance tin glazed ceramics from the 10th to the 17th century AD.

Microstructure and magnetic properties of Ni50 Mn37 Sn13 Heusler alloy ribbons

The Heusler alloy Ni50 Mn37 Sn13 was successfully produced as ribbon flakes of thickness around 7-10 μm melt spinning. Fracture cross section micrographs in the ribbon show the formation of a microcrystalline columnarlike microstructure, with their longer axes perpendicular to the ribbon plane. Phase transition temperatures of the martensite-austenite transformation were found to be MS =218 K, Mf =207 K, AS =224 K, and Af =232 K; the thermal hysteresis of the transformation is 15 K. Ferromagnetic L 21 bcc austenite phase shows a Curie point of 313 K, with cell parameter a=0.5971 (5) nm at 298 K, transforming into a modulated 7M orthorhombic martensite with a=0.6121 (7) nm, b=0.6058 (8) nm, and c=0.5660 (2) nm, at 150 K

Synthesis of triheptanoin and formulation as a solid diet for rodents

Triheptanoin-enriched diets have been successfully used in the experimental treatment of various metabolic disorders. Maximal therapeutic effect is achieved in the context of a ketogenic diet where triheptanoin oil provides 30-40% of the daily caloric intake. However, pre-clinical studies using triheptanoin-rich diets are hindered by the difficulty of administering to laboratory animals as a solid foodstuff. In the present study, we successfully synthesized triheptanoin to the highest standards of purity from glycerol and heptanoic acid, using sulfonated charcoal as a catalyst. Triheptanoin oil was then formulated as a solid, stable and palatable preparation using a ketogenic base and a combination of four commercially available formulation agents: hydrophilic fumed silica, hydrophobic fumed silica, microcrystalline cellulose, and talc. Diet compliance and safety was tested on C57Bl/6 mice over a 15-week period, comparing overall status and body weight change. Practical applications: This work provides a complete description of (i) an efficient and cost-effective synthesis of triheptanoin and (ii) its formulation as a solid, stable, and palatable ketogenic diet (triheptanoin-rich; 39% of the caloric intake) for rodents. Triheptanoin-rich diets will be helpful on pre-clinical experiments testing the therapeutic efficacy of triheptanoin in different rodent models of human diseases. In addition, using the same solidification procedure, other oils could be incorporated into rodent ketogenic diet to study their dosage and long-term effects on mammal health and development. This approach could be extremely valuable as ketogenic diet is widely used clinically for epilepsy treatment.

Synthesis of triheptanoin and formulation as a solid diet for rodents

Triheptanoin-enriched diets have been successfully used in the experimental treatment of various metabolic disorders. Maximal therapeutic effect is achieved in the context of a ketogenic diet where triheptanoin oil provides 30-40% of the daily caloric intake. However, pre-clinical studies using triheptanoin-rich diets are hindered by the difficulty of administering to laboratory animals as a solid foodstuff. In the present study, we successfully synthesized triheptanoin to the highest standards of purity from glycerol and heptanoic acid, using sulfonated charcoal as a catalyst. Triheptanoin oil was then formulated as a solid, stable and palatable preparation using a ketogenic base and a combination of four commercially available formulation agents: hydrophilic fumed silica, hydrophobic fumed silica, microcrystalline cellulose, and talc. Diet compliance and safety was tested on C57Bl/6 mice over a 15-week period, comparing overall status and body weight change. Practical applications: This work provides a complete description of (i) an efficient and cost-effective synthesis of triheptanoin and (ii) its formulation as a solid, stable, and palatable ketogenic diet (triheptanoin-rich; 39% of the caloric intake) for rodents. Triheptanoin-rich diets will be helpful on pre-clinical experiments testing the therapeutic efficacy of triheptanoin in different rodent models of human diseases. In addition, using the same solidification procedure, other oils could be incorporated into rodent ketogenic diet to study their dosage and long-term effects on mammal health and development. This approach could be extremely valuable as ketogenic diet is widely used clinically for epilepsy treatment.

Kalvosuodatusprosessin tehostaminen paperiteollisuuden sovelluksissa

Tässä diplomityössä tutkittiin kalvosuodatuksen esikäsittelymenetelmiä ja kalvonpesua. Työn kirjallisuusosassa käsitellään vuon alenemiseen vaikuttavia tekijöitä, esikäsittelymenetelmiä ja kalvonpesua. Kokeellisessa osassa tutkittiin kemiallisten esikäsittelyjen vaikutusta vuon alenemiseen paperitehtaan happaman kiertoveden kirkkaan suodoksen kalvosuodatuksessa. Esikäsittelykemikaalit olivat ympäristöystävällisiä ja paperinvalmistusprosessiin soveltuvia. Lisäksi tutkittiin kalvonpesuaineiden pesutehokkuuksia. Tutkitut esikäsittelyaineet olivat mikrokiteinen kitosaani, karboksimetyyliselluloosa, selluloosa- ja puukuitu sekä kaupallinen antiskalantti. Pesuaineista tutkittiin kolmea kaupallista kalvonpesuainetta, yhtä kalvopesun tehostusainetta sekä peretikkahappoa. Kokeet tehtiin kahdella laboratoriomittakaavaisella kalvosuodattimella. Kalvoina käytettiin kahta nanosuodatus- ja yhtä ultrasuodatuskalvoa. Vuon alenemista tutkittiin suodatuksen aikaisena alenemisena ja vesivuohon verrattavana alenemisena. Esikäsittelyjen vaikutusta erotustehokkuuteen tutkittiin ioni-, johtokyky-, orgaanisen hiilen kokonaispitoisuus-, sokeri-, sameus- ja ligniinireduktioilla. Lisäksi määritettiin kalvon likaantuminen suodatuksen aikana vesivuon määrityksillä ennen ja jälkeen suodatuksen. Pesutehokkuus määritettiin vesivuon määrityksillä suodatuksen jälkeen ja pesun jälkeen. Kitosaani- ja karboksimetyyliselluloosakäsittelyillä oli vuon alenemista estävä vaikutus hydrofiilisellä nanosuodatuskalvolla suodatettaessa. Kitosaanikäsittelyn 5 g/dm3:n ja karboksimetyyliselluloosakäsittelyn 2 g/ dm3:n annostuksella vuot alentuivat suodatuksen aikana 8 %-yksikköä vähemmän kuin ilman esikäsittelyä. Puukuitukäsittely stabiloi 0,1 g/dm3:n annostuksella saman kalvon vuota, kun kiintoainetta ei poistettu syötöstä. Hydrofobisen nanosuodatuskalvon vuon alenemista ehkäisivät puu- ja selluloosakuitukäsittelyt sekä karboksimetyyliselluloosakäsittely. Karboksimetyyliselluloosakäsittely vähensi vuon alenemista 25 %-yksikköä ja puukuitukäsittely 13 %-yksikköä. Hydrofiilisellä ultrasuodatuskalvolla vuon aleneminen oli pientä ilman esikäsittelyä. Reduktioihin esikäsittelyt vaikuttivat parhaiten ultrasuodatuskalvolla. Kitosaanikäsittely nosti 1 g/dm3:n annostuksella alumiinireduktion 50 %:sta 96 %:iin ja 5 g/dm3:n annostuksella rautareduktion 30 %:sta 55 %:iin. Karboksyylimetyyliselluloosakäsittelyt vaikuttivat parantavasti mangaanin, magnesiumin, raudan ja kalsiumin reduktioihin. Optimi karboksyylimetyyliselluloosa-annostus oli 2 g/dm3. Merkittävin reduktion nousu oli kalsiumilla, jonka reduktio nousi esikäsittelyllä 4 %:sta 57 %:iin. Reduktiota nostava mekanismi oli kalvon pinnalle muodostuva sekundaarikerros. Pesuaineista tehokkain oli entsyymiä sisältävä kalvonpesuaine. Suurin vaikutus sillä oli hydrofobisen nanosuodatuskalvon pesussa. Optimiannostuksella (0,5 %) kalvon vesivuo pesun jälkeen oli 114 % pesua edeltäneestä vesivuosta. Muut kaupalliset pesuaneet oli tehokkaita hydrofiilisille kalvoille. Peretikkahappo oli yksittäisenä pesuaineena heikkotehoinen.

Thin Film Transistors obtained by Hot-Wire CVD

Hydrogenated microcrystalline silicon films obtained at low temperature (150-280°C) by hot wire chemical vapour deposition at two different process pressures were measured by Raman spectroscopy, X-ray diffraction (XRD) spectroscopy and photothermal deflection spectroscopy (PDS). A crystalline fraction >90% with a subgap optical absortion 10 cm -1 at 0.8 eV were obtained in films deposited at growth rates >0.8 nm/s. These films were incorporated in n-channel thin film transistors and their electrical properties were measured. The saturation mobility was 0.72 ± 0.05 cm 2/ V s and the threshold voltage around 0.2 eV. The dependence of their conductance activation energies on gate voltages were related to the properties of the material.

A técnica da reflectância difusa aplicada ao estudo da fluorescência de 2,3-naftalimidas n-substituídas com grupos alquila incluídas em b-ciclodextrina e adsorvidas em celulose microcristalina

The solution fluorescence of N-alkyl-2,3-naphthalimides (1-4) in polar protic and aprotic solvents was compared to the emission from solid samples resulting from the imide complexation with b-cyclodextrin or adsorption on the surface of microcrystalline cellulose. Solid samples of the inclusion complex 2,3-naphthalimides/b-cyclodextrin show maximum for fluorescence emission significantly different to the observed in methanolic solution. Beside this, a clear effect on the alkyl chain length could be observed for these samples which is probably due to differences in probe location inside the cyclodextrin cavity. The constancy for fluorescence quantum yield and fluorescence lifetime for the imides 1 - 4 adsorbed on microcrystalline cellulose suggests that, independently of the polarity of the solvent used for sample preparation, the probe is preferentially located on the cellulose surface. An increase of fluorescence quantum yield and fluorescence lifetime for solid samples, when compared to the values obtained in solution for the different solvents employed in this study (acetonitrile, methanol and water), is fully in accordance with a decrease of the probe mobility due to inclusion in b-cyclodextrin or to adsorption on cellulose.