Effects of alloying elements on the corrosion behavior and biocompatibility of biodegradable magnesium alloys: a review

Magnesium (Mg) based alloys have been extensively considered for their use as biodegradable implant materials. However, controlling their corrosion rate in the physiological environment of the human body is still a significant challenge. One of the most effective approaches to address this challenge is to carefully select alloying compositions with enhanced corrosion resistance and mechanical properties when designing the Mg alloys. This paper comprehensively reviews research progress on the development of Mg alloys as biodegradable implant materials, highlighting the effects of alloying elements including aluminum (Al), calcium (Ca), lithium (Li), manganese (Mn), zinc (Zn), zirconium (Zr), strontium (Sr) and rare earth elements (REEs) on the corrosion resistance and biocompatibility of Mg alloys, from the viewpoint of the design and utilization of Mg biomaterials. The REEs covered in this review include cerium (Ce), erbium (Er), lanthanum (La), gadolinium (Gd), neodymium (Nd) and yttrium (Y). The effects of alloying elements on the microstructure, corrosion behavior and biocompatibility of Mg alloys have been critically summarized based on specific aspects of the physiological environment, namely the electrochemical effect and the biological behavior. This journal is © the Partner Organisations 2014.

Corrosion behavior of Mg-5Al-xZn alloys in 3.5 wt.% NaCl solution

Five types of Mg-5Al alloys with different weight percentages of Zn ranging from 0 to 4 wt.% were examined using electrochemical techniques and surface analysis. The electrochemical results indicated that the Mg-5Al alloys containing Zn have a lower corrosion and hydrogen evolution rates than the Mg-5Al based specimens with a decrease of value being observed with the decrease in Zn content. Zn addition induced the precipitation of Mg-Al and Mg-Zn phases in the Mg matrix along with grain refinement and increased an interaction of Zn oxide with Mg and Al products serving as a corrosion barrier. © 2014 Elsevier B.V. All rights reserved.

Modeling of hardening and softening processes in Mg alloys

The tensile deformation behavior of a range of supersaturated Mg-Al solid solutions and an as-cast magnesium alloy AM60 has been studied. The Mg-Al alloys were tested at room temperature while the alloy AM60 was tested in the temperature range 293-573 K. The differences in the deformation behavior of the alloys is discussed in terms of hardening and softening processes. In order to identify which processes were active, the stress dependence of the strain-hardening coefficient was assessed using Lukac and Balik's model of hardening and softening. The analysis indicates that hardening involves solid solution hardening and interaction with forest dislocations and non-dislocation obstacles such as second phase particles. Cross slip is not a significant recovery process in the temperature range 293-423 K. At temperatures between 473 and 523 K the analysis suggests that softening is controlled by cross slip and climb of dislocations. At temperatures above 523 K softening seems to be controlled by dynamic recrystallisation. (C) 2004 Elsevier B.V. All rights reserved.

Corrosion resistance of anodised single-phase Mg alloys

This work studied the effect of the impurity iron and the alloying elements aluminium and zinc in single-phase substrate magnesium alloys on the corrosion resistance of the alloys after anodisation. It was found that increasing zinc content (0-2%) led to increased corrosion resistance of an anodised single-phase Mg-Zn alloy. The addition of Al lowered the corrosion resistance of an anodised commercial purity Mg-Al single-phase alloy, whereas the same addition was found to be beneficial to the corrosion resistance of an anodised high purity Mg-Al single-phase alloy. Heat-treatment made the substrate Mg-Al and Mg-Zn alloys more uniform and hence improved the corrosion resistance of the alloys after anodisation. The detrimental effect of iron impurity on corrosion performance of the unanodised substrate single-phase magnesium alloys was inherited by the anodised alloys. The corrosion resistance of the anodised Mg alloys was found to be closely correlated with the corrosion performance of the unanodised as-cast Mg alloys. (c) 2005 Elsevier B.V. All rights reserved.

Grain refinement of Mg-Al(-Mn) alloys by SiC additions

The addition of SiC particles effectively grain refined a range of Mg-Al alloys. The greatest reductions in grain size were found for the alloys with lower Al contents. The presence of Mg2Si in the microstructure after that SiC addition, and consideration of phase equilibria suggested that the SiC transforms to Al4C3, and this is the actual nucleant. The addition of Mn poisoned the grain refining effect of the SiC addition, probably due to the formation of less potent Al-Mn-carbides. (c) 2006 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Mechanical properties, in vitro corrosion and biocompatibility of newly developed biodegradable Mg-Zr-Sr-Ho alloys for biomedical applications

Our previous studies have demonstrated that Mg-Zr-Sr alloys can be anticipated as excellent biodegradable implant materials for load-bearing applications. In general, rare earth elements (REEs) are widely used in magnesium (Mg) alloys with the aim of enhancing the mechanical properties of Mg-based alloys. In this study, the REE holmium (Ho) was added to an Mg-1Zr-2Sr alloy at different concentrations of Mg1Zr2SrxHo alloys (x = 0, 1, 3, 5 wt. %) and the microstructure, mechanical properties, degradation behaviour and biocompatibility of the alloys were systematically investigated. The results indicate that the addition of Ho to Mg1Zr2Sr led to the formation of the intermetallic phases MgHo3, Mg2Ho and Mg17Sr2 which resulted in enhanced mechanical strength and decreased degradation rates of the Mg-Zr-Sr-Ho alloys. Furthermore, Ho addition (≤5 wt. %) to Mg-Zr-Sr alloys led to enhancement of cell adhesion and proliferation of osteoblast cells on the Mg-Zr-Sr-Ho alloys. The in vitro biodegradation and the biocompatibility of the Mg-Zr-Sr-Ho alloys were both influenced by the Ho concentration in the Mg alloys; Mg1Zr2Sr3Ho exhibited lower degradation rates than Mg1Zr2Sr and displayed the best biocompatibility compared with the other alloys.

Vapour composition and activities in Mg-Zn liquid alloy at 923 K

Vapour species effusing from a magnesia Knudsen cell containing Mg-Zn alloy at 923 K were condensed on a water cooled copper plate. The equilibrium composition of the vapour phase over the alloy was determined from chemical analysis of the condensate. The activity coefficients of both components in the alloy have been derived from the data using a modified Gibbs-Duhem relation. The ratio of saturation vapour pressures of pure Zn and Mg obtained from the analysis of alloy data agree well with values from the literature, providing an internal check on the accuracy of data obtained in this study. Both components of the alloy exhibit negative deviations from Raoult's law. The concentration-concentration structure factor of Bhatia and Thomton at zero wave vector, evaluated from the measurements, indicate the presence of MgZn2 type complex in the liquid state. The associated regular solution model has been used for the thermodynamic description of liquid Mg-Zn alloys.

The deciding role of texture on ductility in a Ce containing Mg alloy

This is the first successful attempt to produce Mg-Ce alloys of different texture through different processing routes while keeping the grain size and grain size distribution same. Tensile data shows that contribution of texture to ductility enhancement is primary and that of grain refinement is secondary. The texture resulting from multi-axial forging of extruded billets followed by annealing exhibits the highest ductility (similar to 40%) at room temperature. (C) 2015 Elsevier B.V. All rights reserved.

Studies on grain refinement and alloying additions on the microstructure and mechanical properties of Mg-8Zn-4Al alloy

MAGNESIUM ALLOYS have strong potential for weight reduction in a wide range of technical applications because of their low density compared to other structural metallic materials. Therefore, an extensive growth of magnesium alloys usage in the automobile sector is expected in the coming years to enhance the fuel efficiency through mass reduction. The drawback associated with the use of commercially cheaper Mg-Al based alloys, such as AZ91, AM60 and AM50 are their inferior creep properties above 100ºC due to the presence of discontinuous Mg17A112 phases at the grain boundaries. Although rare earth-based magnesium alloys show better mechanical properties, it is not economically viable to use these alloys in auto industries. Recently, many new Mg-Al based alloy systems have been developed for high temperature applications, which do not contain the Mg17Al12 phase. It has been proved that the addition of a high percentage of zinc (which depends upon the percentage of Al) to binary Mg-Al alloys also ensures the complete removal of the Mg17Al12 phase and hence exhibits superior high temperature properties.ZA84 alloy is one such system, which has 8%Zn in it (Mg-8Zn-4Al-0.2Mn, all are in wt %) and shows superior creep resistance compared to AZ and AM series alloys. These alloys are mostly used in die casting industries. However, there are certain large and heavy components, made up of this alloy by sand castings that show lower mechanical properties because of their coarse microstructure. Moreover, further improvement in their high temperature behaviour through microstructural modification is also an essential task to make this alloy suitable for the replacement of high strength aluminium alloys used in automobile industry. Grain refinement is an effective way to improve the tensile behaviour of engineering alloys. In fact, grain refinement of Mg-Al based alloys is well documented in literature. However, there is no grain refiner commercially available in the market for Mg-Al alloys. It is also reported in the literature that the microstructure of AZ91 alloy is modified through the minor elemental additions such as Sb, Si, Sr, Ca, etc., which enhance its high temperature properties because of the formation of new stable intermetallics. The same strategy can be used with the ZA84 alloy system to improve its high temperature properties further without sacrificing the other properties. The primary objective of the present research work, “Studies on grain refinement and alloying additions on the microstructure and mechanical properties of Mg-8Zn-4Al alloy” is twofold: 1. To investigate the role of individual and combined additions of Sb and Ca on the microstructure and mechanical properties of ZA84 alloy. 2. To synthesis a novel Mg-1wt%Al4C3 master alloy for grain refinement of ZA84 alloy and investigate its effects on mechanical properties.

Solidification of cast magnesium alloys

A description of the key solidification steps in the formation of the as-cast microstructure of magnesium alloys is presented. The focus is on the two common magnesium alloy groups: Mg-Al alloys and Mg-Zn-rare earth alloys. The key elements described are: nucleation (including grain refinement), growth of the primary phase and the formation of the eutectic phases. In addition the effect of casting process (e.g. high-pressure diecasting and sand casting) on the outcomes from solidification are discussed. This includes consideration of the formation of banded defects during solidification in the dynamic environment of high pressure die casting.

Zirconium, calcium, and strontium contents in magnesium based biodegradable alloys modulate the efficiency of implant-induced osseointegration

Development of new biodegradable implants and devices is necessary to meet the increasing needs of regenerative orthopedic procedures. An important consideration while formulating new implant materials is that they should physicochemically and biologically mimic bone-like properties. In earlier studies, we have developed and characterized magnesium based biodegradable alloys, in particular magnesium-zirconium (Mg-Zr) alloys. Here we have reported the biological properties of four Mg-Zr alloys containing different quantities of strontium or calcium. The alloys were implanted in small cavities made in femur bones of New Zealand White rabbits, and the quantitative and qualitative assessments of newly induced bone tissue were carried out. A total of 30 experimental animals, three for each implant type, were studied, and bone induction was assessed by histological, immunohistochemical and radiological methods; cavities in the femurs with no implants and observed for the same period of time were kept as controls. Our results showed that Mg-Zr alloys containing appropriate quantities of strontium were more efficient in inducing good quality mineralized bone than other alloys. Our results have been discussed in the context of physicochemical and biological properties of the alloys, and they could be very useful in determining the nature of future generations of biodegradable orthopedic implants.

Collagen type-I leads to in vivo matrix mineralization and secondary stabilization of Mg-Zr-Ca alloy implants

Biodegradable magnesium-zirconia-calcium (Mg-Zr-Ca) alloy implants were coated with Collagen type-I (Coll-I) and assessed for their rate and efficacy of bone mineralization and implant stabilization. The phases, microstructure and mechanical properties of these alloys were analyzed using X-ray diffraction (XRD), optical microscopy and compression test, respectively, and the corrosion behavior was established by their hydrogen production rate in simulated body fluid (SBF). Coll-I extracted from rat tail, and characterized using fourier transform infrared (FT-IR) spectroscopy, was used for dip-coating the Mg-based alloys. The coated alloys were implanted into the femur bones of male New Zealand white rabbits. In vivo bone formation around the implants was quantified by measuring the bone mineral content/density (BMC/BMD) using dual-energy X-ray absorptiometry (DXA). Osseointegration of the implant and new bone mineralization was visualized by histological and immunohistochemical analysis. Upon surface coating with Coll-I, these alloys demonstrated high surface energy showing enhanced performance as an implant material that is suitable for rapid and efficient new bone tissue induction with optimal mineral content and cellular properties. The results demonstrate that Coll-I coated Mg-Zr-Ca alloys have a tendency to form superior trabecular bone structure with better osteoinduction around the implants and higher implant secondary stabilization, through the phenomenon of contact osteogenesis, compared to the control and uncoated ones in shorter periods of implantation. Hence, Coll-I surface coating of Mg-Zr-Ca alloys is a promising method for expediting new bone formation in vivo and enhancing osseointegration in load bearing implant applications.

Propiedades ópticas y estructurales de nanoestructuras de Zn(Cd)(Mg)O

En la presente tesis doctoral se ha realizado un estudio utilizando diferentes técnicas de crecimiento (RPE-MOCVD y spray pyrolysis) y estructuras (nanohilos, pozos y puntos cuánticos y capas) con el objetivo de desarrollar dispositivos que cubran desde el rango visible hasta el ultravioleta. Es por esta razón por la que se han elegido materiales basados en ZnO, debido a la posibilidades que estos ofrecen para variar su bandgap en un amplio rango de energías. Prueba de ello es que en este estudio se ha conseguido cubrir un rango espectral desde 1.86 hasta 4.11 eV, estudiandose además fenómenos físicos como son la difusión e incorporaci ón de la aleación o la adsorción de gases en la super_cie, lo que ha permitido la fabricación de diferentes fotodetectores de gran sensibilidad. Por todo ello, los resultados obtenidos en esta tesis suponen una gran contribución al conocimiento de las propiedades físicas de las aleaciones de Zn(Cd)O y Zn(Mg)O para potenciales aplicaciónes en dispositivos que operen en el rango visible y ultravioleta del espectro, respectivamente. En esta memoria se da en primer lugar una visión de las propiedades de materiales basados en ZnO, entrando en detalle en una de las ventajas que este presenta, la facilidad que tiene este material para formar nanoestructuras. En el capítulo 3 se dan los conceptos teóricos necesarios para comprender las propiedades ópticas de este tipo de materiales, mostrando también los resultados más reseñables obtenidos en ZnO. En los capítulos referentes a los resultados se pueden diferenciar dos grandes bloques. En el primer bloque de resultados se han analizado nanohilos y pozos cuánticos de Zn(Cd)O crecidos por la técnica de RPE-MOCVD (Capítulos 4 y 5). En el segundo se expondrá el estudio realizado sobre capas y puntos cuánticos de Zn(Mg)O crecidos por la técnica spray pyrolysis como se describe en mayor detalle a continuación. Nanohilos y pozos cuánticos de Zn(Cd)O crecidos por RPE-MOCVD Teóricamente aleando el ZnO con CdO es posible disminuir el valor del band- gap desde 3.37 eV hasta 0.95 eV, cubriendo por completo el espectro visible. El desarrollo del ternario Zn(Cd)O permitiría la fabricación de heteroestructuras y pozos cuánticos, muy importantes en el desarrollo de dispositivos optoelectrónicos que cubran la parte visible del espectro. Sin embargo, la diferencia de estructura cristalina entre estos dos materiales junto a la baja solubilidad del Cd y su alta presión de vapor, di_culta la obtención de material de alta calidad cristalina con alto contenido en Cd. En esta tesis doctoral se ha realizado una completa caracterización óptica y estructural de nanohilos de Zn(Cd)O credidos por la técnica de RPE-MOCVD. Estos nanohilos tinene unas longitudes comprendidas entre 1 y 3 _m y diámetros entre 100 y 200 nm. La concentración máxima introducida de Cd en estas estructuras ha sido de hasta un 54% manteniendo la estructura wurtzita del ZnO, siendo este el mayor contenido de Cd introducido hasta la fecha en nanostructuras basada en ZnO. Este hecho se traduce en una variación de la energía de emisión entre 3.31 y 1.86 eV con el aumento en Cd. El uso de diferentes técnicas de alta resoluci ón de caracterización estructural ha permitido demostrar la presencia de una sola fase estructural wurtzita sin observarse ningún indicio de separación de fases ni acumulación de Cd a lo largo del nanohilo para todos los contenidos de Cd. Con el propósito de fabricar dispositivos en nanohilos individuales, parte de esta tesis doctoral ha estado dedicada a estudiar el impacto que el recocido térmico tiene en las propiedades ópticas y eléctricas de nanohilos de Zn(Cd)O. El recocido térmico es un proceso clave en la optimización de dispositivos, ya sea para la obtenci ón de contactos óhmicos, reducción de defectos o difusión de dopantes por ejemplo. En este estudio se ha observado una mejora muy signi_cativa de las propiedades de emisión de los nanohilos cuando estos eran recocidos a temperaturas mayores que la de crecimiento (300 oC). En las muestras con Cd se ha observado además que el recocido también produce un desplazamiento de la emisión hacia mayores energías debido a una reducción homogénea del contenido de Cd. Medidas de fotoluminiscencia con resolución temporal muestran el impacto que tiene la localización del excitón en las _uctuaciones de potencial, debidas a una distribución estadística del Cd, en la dinámica de los portadores. Comparando el tiempo de vida de los portadores entre los nanohilos recocidos y sin recocer se ha observado un aumento de este parámetro en las estructuras recocidas. Este aumento es fundamentalmente debido a una reducción de centros de recombinación no radiativa asociados a defectos presentes a lo largo del nanohilo. Además, se ha estudiado la evolución de los tiempos de vida de los portadores en función de la temperatura, registrándose una menor estabilidad con la temperatura de los tiempos de vida en las muestras recocidas. Este resultado sugiere que el recocido térmico consigue reducir parte del desorden de la aleación en la estructura. Tras haber caracterizados los nanohilos se desarrollaron una serie de procesa dos para la fabricación de dispositivos basados en nanohilos individuales. Se fabricaron en concreto fotodetectores sensibles al UV, en los que se observó también la alta sensibilidad que muestran a la adsorción de gases en la super_cie, incrementada por la gran relación super_cie/volúmen característica de las nanoestructuras. Estos procesos de adsorción observados tienen un impacto directo sobre las propiedades ópticas y electricas de los dispositivos como se ha demostrado. Por ello que en esta tesis se hayan estudiado en detalle este tipo de procesos, ideando maneras para tener un mayor control sobre ellos. Finalmente se crecieron estructuras de pozos cuántico de ZnCdO/ZnO en nanohilos con contenidos de Cd nominales de 54 %. Las medidas ópticas realizadas mostraron como al aumentar la anchura del pozo de 0.7 a 10 nm, la emisión relacionada con el pozo se desplazaba entre 3.30 y 1.97 eV. Este gran desplazamiento representa el mayor obtenido hasta la fecha en pozos cuánticos de ZnCdO/ZnO. Sin embargo, al caracterizar estructuralmente estas muestras se observó la presencia de procesos de difusión de Cd entre el pozo y la barrera. Como se ha podido medir, este tipo de procesos reducen sustancialmente la concentración de Cd en el pozo al difundirse parte a la barrera. cambiando completamente la estructura de bandas nominal de estas estructuras. Este estudio demuestra la importancia del impacto de los procesos de difusión en la interpretación de los efectos de con_namiento cuántico para este tipo de estructuras. Capas y puntos cuánticos de Zn(Mg)O crecidos por spray pyrolysis La técnica de spray pyrolysis, debido a su simplicidad, bajo coste y capacidad de crecer sobre grandes áreas conservando una alta calidad cristalina presenta un gran interés en la comunidad cientí_ca para el potencial desarrollo de dispositivos comerciales. En esta tesis se ha estudiado las propiedades ópticas y eléctricas de capas y puntos cuánticos de Zn(Mg)O crecidos por esta técnica. Al contrario que pasa con el Cd, al introducir Mg en la estructura wurtzita de ZnO se consigue aumentar el bandgap del semiconductor. Sin embargo, al igual que pasa con el CdO, la diferencia de estructura cristalina entre el ZnO y el MgO limita la cantidad de Mg que se puede incorporar, haciendo que para una cierta concentración de Mg aparezcan el fenómeno de separación de fases. En esta tesis se ha conseguido incorporar hasta un contenido de Mg del 35% en la estructura wurtzita del ZnO utilizando la técnica de spray pyrolysis, resultado que representa la mayor concentración de Mg publicada hasta la fecha. Este hecho ha posibilitado variar la energía del borde de absorción desde 3.30 a 4.11 eV. En estas capas se ha realizado una completa caracterización óptica observándose una diferencia entre las energías del borde de absorción y del máximo de emisión creciente con el contenido en Mg. Esta diferencia, conocida como desplazamiento de Stokes, es debida en parte a la presencia de _uctuaciones de potencial producidas por un desorden estadístico de la aleación. Se han fabricado fotodetectores MSM de alta calidad utilizando las capas de Zn(Mg)O previamente caracterizadas, observándose un desplazamiento del borde de absorción con el aumento en Mg desde 3.32 a 4.02 eV. Estos dispositivos muestran altos valores de responsividad (10-103 A/W) y altos contrastes entre la responsividad bajo iluminación y oscuridad (10-107). Estos resultados son en parte debidos a la presencia de mecanismos de ganancia y una reducción de la corriente de oscuridad en las muestras con alto contenido de Mg. Utilizando esta misma técnica de crecimiento se han crecido puntos de Zn(Mg)O con concentraciones nominales de Mg entre 0 y 100 %, con dimensiones medias entre 4 y 6 nm. Las medidas estructurales realizadas muestran que hasta un valor de Mg de 45 %, los puntos están compuestos por una única fase estructural, wurtzita. A partir de esa concentración de Mg aparece una fase cúbica en los puntos, coexistiendo con la fase hexagonal hasta una concentración nominales del 85 %. Para concentraciones mayores de Mg, los puntos muestran una única fase estructural cúbica. Medidas de absorción realizadas en estos puntos de Zn(Mg)O muestran un desplazamiento del borde de absorción entre 3.33 y 3.55 eV cuando la concentraci ón de Mg en los puntos aumenta hasta el 40 %. Este desplazamiento observado es debido solamente a la fase wurtzita del Zn(Mg)O donde se incorpora el Mg. ABSTRACT This PhD theis presents a study using di_erent growth techniques (RPEMOCVD and spray pyrolysis) and structures (nanowires, quantum dots and wells and layers) in order to develop devices that extend from the visible to the ultraviolet range. For this reason ZnO based materials have been choosen, because they o_er the possibility to tunne the bandgap in this energy range. Proof of this is that this study has managed to cover a spectral range from 1.86 to 4.11 eV, also being studied physical phenomena such as di_usion and incorporation of alloy or adsorption of gases on the surface, allowing the develop di_erent highly sensitive photodetectors. Therefore, the results obtained in this thesis are a great contribution two large blockso the knowledge of the physical properties of alloys Zn(Cd)O and Zn(Mg)O for potential applications in devices that operate in the visible and ultraviolet range, respectively. In the _rst chapter, the general properties of ZnO-based materials are presented, showing the facilities that these kind of materials o_er to obtain di_erent nanoestructures. In Chapter 3, optical theoretical concepts are given to understand the optical properties of these materials, also showing the most signi_cant results of ZnO. In the chapters related with the results, two blocks could be distinguish. In the _rst one, Zn(Cd)O nanowires and quantum wells grown by RPE-MOCVD have been analyzed (Chapters 4 and 5). The second block of results shows the study performed in Zn(Mg)O _lms and quantum dots grown by spray pyrolysis. Zn(Cd)O nanowires and quantum wells grown by RPE-MOCVD In summary, the results of the PhD thesis are a great contribution to the knowledge of the physical properties of Zn(Cd)O and Zn(Mg)O alloys and their application for high performance devices operating in the visible and UV ranges, respectively. The performance of the device is still limited due to alloy solubility and p-doping stability, which opens a door for future research in this _eld. Theoretically, annealing ZnO with CdO allows to reduce the bandgap from 3.37 to 0.95 eV, covering the whole visible spectrum. The development of ZnCdO alloys allows the fabrication of heterostructures and quantum wells, necessary for the development of high performance optoelectronic devices. However, the di_erent crystal structures between CdO and ZnO and the low solubility of Cd and its high vapor pressure, hinders the growth of ZnCdO alloys with high Cd contents. In this PhD thesis Zn(Cd)O nanowires have been optically and structurally characterized, obtaining a maximum Cd content of 54% while maintaining their wurtzite structure. This Cd content, which allows lowering the bandgap down to 1.86 eV, is the highest concentration ever reported in nanostructures based on ZnO. The combination of optical and structural characterization techniques used during this thesis has allowed the demonstration of the presence of a single wurtzite structure, without observing any indication of phase separation or Cd accumulation along the nanowire. Annealing processes are essential in the fabrication of optoelectronic devices. For this reason, a complete study of the annealing e_ects in the optical and electrical properties of Zn(Cd)O nanowires has been performed. In the _rst place, annealing nanowires at higher temperatures than their growth temperature (300 oC) allows a signi_cant improvement of their emission properties. However, in the samples that contain Cd a shift in the emission towards higher energies has been observed due to a homogeneous reduction of the Cd content in the nanowires. Time resolved photoluminescence measurements show the impact of the exciton localization in the potential _uctuations due to a statistical alloy disorder. An increase in the carrier lifetime has been obtained for the annealed nanowires. This increase is mainly due to the reduction of non-radiative recombination centers associated with the defects present in the material. Furthermore, temperature dependent time resolved photoluminescence measurements suggest a reduction of the alloy disorder in the annealed samples. In this thesis, single nanowire photodetectors with a high responsivity in the UV range have been demonstrated. Due to the high surface/volume ratio, these structures are very sensitive to gas adsorption at the surface, which largely de_nes the optical and electrical properties of the material and, therefore, of the device. With the aim of obtaining time stable devices, the dynamic adsorption-desorption processes have been studied, developing di_erent approaches that allow a higher control over them. Finally, ZnCdO/ZnO quantum wells have been grown with a nominal Cd concentration of 54% inside the well. The performed optical measurements show that increasing the well width from 0.7 to 10 nm, shifts the emission related with the well from 3.30 to 1.97 eV. This result represents the highest shift reported in the literature. However, a detailed structural characterization shows the presence of di_usion phenomena which substantially reduce the concentration of Cd in the well, while increasing it in the barrier. This type of phenomena should be considered when ac curately interpretating the quantum con_nement e_ects in Zn(Cd)O/ZnO quantum wells. Theoretically, annealing ZnO with CdO allows to decrease the bandgap from 3.37 to 0.95 eV, covering the whole visible spectrum. Zn(Mg)O _lms and quantum dots grown by spray pyrolysis Due to its simplicity, low-cost and capacity to grow over large areas conserving a high crystal quality, spray pyrolysis technique presents a great interest in the scienti_c community for developing comercial devices. In this thesis, a complete study of the optical and structural properties of Zn(Mg)O _lms and quantum dots grown by spray pyrolysis has been performed. Contrary to Zn(Cd)O alloys, when introducing Mg in the ZnO wurtzite structure an increase in the bandgap in obtained. Once again, the di_erence in the crystal structure of ZnO and MgO limits the amount of Mg that can be introduced before phase separation appears. In this PhD thesis, a maximum Mg content of 35% has been incorporated in the wurtzite structure using spray pyrolysis. This variation in the Mg content translates into an increase of the absorption edge from 3.30 to 4.11 eV. Up to this date, this result represents the highest Mg content introduced by spray pyrolysis in a ZnO wurzite structure reported in the literature. The comparison of the emission and absorption spectra shows the presence of an increasing Stokes shift with Mg content. This phenomenon is partialy related with the presence of potential _uctuations due to an statistic alloy disorder. MSM photodetectors have been processed on previously characterized Zn(Mg)O _lms. These devices have shown a shift in the absorption edge from 3.32 to 4.02 eV with the increase in Mg content, high responsivity values (10-103 A/W) and high contrast ratios between illuminated and dark responsivities (10-107). These values are explained by the presence of a gain mechanism and a reduction of dark current in the ZnMgO samples. Zn(Mg)O quantum dots have also been grown using spray pyrolysis with Mg concentrations between 0 and 100% and with average widths ranging 4 to 6 nm. Structural measurements show that at a Mg concentration of 45% the cubic phase appears, coexisting with the hexagonal phase up to an 85% concentration of Mg content. From 85% onwards the quantum dots show only the cubic phase. Absorption measurements performed in these structures reveal a shift in the absorption edge from 3.33 to 3.55 eV when the Mg content increases up to 40 %.

Stress corrosion cracking and hydrogen embrittlement of an Al-Zn-Mg-Cu alloy

The age hardening, stress corrosion cracking (SCC) and hydrogen embrittlement (HE) of an Al-Zn-Mg-Cu 7175 alloy were investigated experimentally. There were two peak-aged states during ageing. For ageing at 413 K, the strength of the second peak-aged state was slightly higher than that of the first one, whereas the SCC susceptibility was lower, indicating that it is possible to heat treat 7175 to high strength and simultaneously to have high SCC resistance. The SCC susceptibility increased with increasing Mg segregation at the grain boundaries. Hydrogen embrittlement (HE) increased with increased hydrogen charging and decreased with increasing ageing time for the same hydrogen charging conditions. Computer simulations were carried out of (a) the Mg grain boundary segregation using the embedded atom method and (b) the effect of Mg and H segregation on the grain boundary strength using a quasi-chemical approach. The simulations showed that (a) Mg grain boundary segregation in Al-Zn-Mg-Cu alloys is spontaneous, (b) Mg segregation decreases the grain boundary strength, and (c) H embrittles the grain boundary more seriously than does Mg. Therefore, the SCC mechanism of Al-Zn-Mg Cu alloys is attributed to the combination of HE and Mg segregation induced grain boundary embrittlement. (C) 2004 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Grain size measurements in Mg-Al high pressure die castings using electron back-scattered diffraction (EBSD)

Optical metallographic techniques for grain-size measurement give unreliable results for high pressure diecast Mg-Al alloys and electron back-scattered diffraction mapping (EBSD) provides a good tool for improving the quality of these measurements. An application of EBSD mapping to this question is described, and data for some castings are presented. Ion-beam milling was needed to prepare suitable samples, and this technique is detailed. As is well-known for high pressure die castings, the grain size distribution comprises at least two populations. The mean grain size of the fine-grained population was similar in both AZ91 and AM60 and in two casting thicknesses (2 mm and 5 mm) and, contrary to previously published reports, it did not vary with depth below the surface.