Modelling of Unsteady Gas-Dynamic Flow in a Pipe and at its Exit Using CFD

Traditionally the simulation of the thermodynamic aspects of the internal combustion engine has been undertaken using one-dimensional gas-dynamic models to represent the intake and exhaust systems. CFD analysis of engines has been restricted to modelling of in-cylinder flow structures. With the increasing accessibility of CFD software it is now worth considering its use for complete gas-dynamic engine simulation. This paper appraises the accuracy of various CFD models in comparison to a 1D gas-dynamic simulation. All of the models are compared to experimental data acquired on an apparatus that generates a single gas-dynamic pressure wave. The progress of the wave along a constant area pipe and its subsequent reflection from the open pipe end are recorded with a number of high speed pressure transducers. It was found that there was little to choose between the accuracy of the 1D model and the best CFD model. The CFD model did not require experimentally derived loss coefficients to accurately represent the open pipe end; however, it took several hundred times longer to complete its analysis. The best congruency between the CFD models and the experimental data was achieved using the RNG k-e turbulence model. The open end of the pipe was most effectively represented by surrounding it with a relatively small volume of cells connected to the rest of the environment using a pressure boundary.

Novel chiral ionic liquids:physicochemical properties and investigation of the internal rotameric behaviour in the neat system

Optically active S-alkyl-N, N'-bis((S)-1-phenylethyl) thiouronium salts, abbreviated as (S)-[Cnpetu] Y (where Y is an anion; n = 1, 2, 3, 4, 6, 8, 10, 12 or 16), have been prepared and studied by a broad spectrum of analyses. This consists of density, viscosity, and conductivity determination, followed by a discussion of relevant correlations. Unusual trends depending on the S-alkyl chain length were documented for (S)-[Cnpetu][ NTf2] series (where [NTf2] = bis{(trifluoromethyl) sulfonyl} amide), including the viscosity decreasing with increasing chain length, and the conductivity showing a maximum between the S-butyl and the S-hexyl derivative. In addition, a hindered rotamerism of the thiouronium cation in dmso-d(6) solution was recognised by H-1 and C-13 NMR techniques. Thorough analysis of NMR spectra confirmed that the main contribution comes from rotation about the partial double C-S bond. For the first time, a neat thiouronium ionic liquid system has been subjected to quantitative analysis of hindered rotamerism by dynamic NMR coalescence studies, with estimated activation energy for rotation of 63.9 +/- 0.4 kJ mol(-1). Finally, the application of (S)-[C(n)petu] Y salts as chiral discriminating agents for carboxylates by 1H NMR spectroscopy was further investigated, demonstrating the influence of the S-alkyl chain length on chiral recognition; (S)-[C(2)petu][NTf2] ionic liquid with the mandelate anion gave the best results.

Refresh-free dynamic standard-cell based memories: Application to a QC-LDPC decoder

The area and power consumption of low-density parity check (LDPC) decoders are typically dominated by embedded memories. To alleviate such high memory costs, this paper exploits the fact that all internal memories of a LDPC decoder are frequently updated with new data. These unique memory access statistics are taken advantage of by replacing all static standard-cell based memories (SCMs) of a prior-art LDPC decoder implementation by dynamic SCMs (D-SCMs), which are designed to retain data just long enough to guarantee reliable operation. The use of D-SCMs leads to a 44% reduction in silicon area of the LDPC decoder compared to the use of static SCMs. The low-power LDPC decoder architecture with refresh-free D-SCMs was implemented in a 90nm CMOS process, and silicon measurements show full functionality and an information bit throughput of up to 600 Mbps (as required by the IEEE 802.11n standard).

Progressing from internal to supply chain level environmental strategies: The influence of internal support processes

The need for companies to consider the environmental impact of their operations and supply chains has been highlighted in the literature. However, few studies appear to consider how companies’ progress from proactive environmental strategies implemented at the internal, operations level to proactive environmental strategies implemented at the supply chain level. This study assesses the implementation process through the lens of the natural resource-based view and dynamic capabilities perspective. First, the link between the internal strategy ‘pollution prevention’ and the supply chain strategy ‘process stewardship’ is assessed. Second, the mediating influence of the internal support processes ‘integration’ and ‘learning’ on the implementation process is considered. Data collected from a sample of 1200 UK-based food manufacturing companies is analysed using multiple regression analysis. The findings suggest that the progression to environmental efforts at the supply chain level begins with internally-based environmental efforts and that the integration of these efforts and experience gained from them are important supporting factors in this progression.

Cooperation mechanism for team-work based multi-agent system in dynamic scheduling through meta-heuristics

This paper describes a Multi-agent Scheduling System that assumes the existence of several Machines Agents (which are decision-making entities) distributed inside the Manufacturing System that interact and cooperate with other agents in order to obtain optimal or near-optimal global performances. Agents have to manage their internal behaviors and their relationships with other agents via cooperative negotiation in accordance with business policies defined by the user manager. Some Multi Agent Systems (MAS) organizational aspects are considered. An original Cooperation Mechanism for a Team-work based Architecture is proposed to address dynamic scheduling using Meta-Heuristics.

JPEG decoder implementation on FPGA using dynamic partial reconfiguration

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia de Electrónica e telecomunicações

Using dynamic reconfiguration to reduce the area of a JPEG decoder on FPGA

Partial dynamic reconfiguration of FPGAs can be used to implement complex applications using the concept of virtual hardware. In this work we have used partial dynamic reconfiguration to implement a JPEG decoder with reduced area. The image decoding process was adapted to be implemented on the FPGA fabric using this technique. The architecture was tested in a low cost ZYNQ-7020 FPGA that supports dynamic reconfiguration. The results show that the proposed solution needs only 40% of the resources utilized by a static implementation. The performance of the dynamic solution is about 9X slower than the static solution by trading-off internal resources of the FPGA. A throughput of 7 images per second is achievable with the proposed partial dynamic reconfiguration solution.

Static and dynamic shoulder stabilizer adaptations in javelin throwers: A preliminary study

BACKGROUND: Adaptations to Internal (IR) and external (ER) rotator shoulder muscles improving overhead throwing kinematics could lead to muscular strength imbalances and be considered an intrinsic risk factor for shoulder injury, as well as modified shoulder range of motion (RoM). OBJECTIVE: To establish profiles of internal and external rotation RoM and isokinetic IR and ER strength in adolescent- and national-level javelin throwers. METHODS: Fourteen healthy subjects were included in this preliminary cross-sectional study, 7 javelin throwers (JTG) and 7 nonathletes (CG). Passive internal and external rotation RoM were measured at 90 degrees of shoulder abduction. Isokinetic strength of dominant and non-dominant IR and ER was evaluated during concentric (60, 120 and 240 degrees/s) and eccentric (60 degrees/s) contractions by Con-Trex (R) dynamometer with the subject in a seated position with 45 degrees of shoulder abduction in the scapular plane. RESULTS: We reported significantly lower internal rotation and significantly higher external rotation RoM in JTG than in CG. Concentric and eccentric IR and ER strength were significantly higher for the dominant shoulder side in JTG (P < 0.05), without significant differences in ER/IR ratios. CONCLUSIONS: The main finding of this preliminary study confirmed static and dynamic shoulder stabilizer adaptations due to javelin throw practice in a population of adolescent- and national-level javelin throwers.

Direct-on-line axial flux permanent magnet synchronous generator static and dynamic performance

In distributed energy production, permanent magnet synchronous generators (PMSG) are often connected to the grid via frequency converters, such as voltage source line converters. The price of the converter may constitute a large part of the costs of a generating set. Some of the permanent magnet synchronous generators with converters and traditional separately excited synchronous generators couldbe replaced by direct-on-line (DOL) non-controlled PMSGs. Small directly networkconnected generators are likely to have large markets in the area of distributed electric energy generation. Typical prime movers could be windmills, watermills and internal combustion engines. DOL PMSGs could also be applied in island networks, such as ships and oil platforms. Also various back-up power generating systems could be carried out with DOL PMSGs. The benefits would be a lower priceof the generating set and the robustness and easy use of the system. The performance of DOL PMSGs is analyzed. The electricity distribution companies have regulations that constrain the design of the generators being connected to the grid. The general guidelines and recommendations are applied in the analysis. By analyzing the results produced by the simulation model for the permanent magnet machine, the guidelines for efficient damper winding parameters for DOL PMSGs are presented. The simulation model is used to simulate grid connections and load transients. The damper winding parameters are calculated by the finite element method (FEM) and determined from experimental measurements. Three-dimensional finite element analysis (3D FEA) is carried out. The results from the simulation model and 3D FEA are compared with practical measurements from two prototype axial flux permanent magnet generators provided with damper windings. The dimensioning of the damper winding parameters is case specific. The damper winding should be dimensioned based on the moment of inertia of the generating set. It is shown that the damper winding has optimal values to reach synchronous operation in the shortest period of time after transient operation. With optimal dimensioning, interferenceon the grid is minimized.

Validation of plant dynamic model by online and laboratory measurements – a tool to predict online COD loads out of production of mechanical printing papers

COD discharges out of processes have increased in line with elevating brightness demands for mechanical pulp and papers. The share of lignin-like substances in COD discharges is on average 75%. In this thesis, a plant dynamic model was created and validated as a means to predict COD loading and discharges out of a mill. The assays were carried out in one paper mill integrate producing mechanical printing papers. The objective in the modeling of plant dynamics was to predict day averages of COD load and discharges out of mills. This means that online data, like 1) the level of large storage towers of pulp and white water 2) pulp dosages, 3) production rates and 4) internal white water flows and discharges were used to create transients into the balances of solids and white water, referred to as “plant dynamics”. A conversion coefficient was verified between TOC and COD. The conversion coefficient was used for predicting the flows from TOC to COD to the waste water treatment plant. The COD load was modeled with similar uncertainty as in reference TOC sampling. The water balance of waste water treatment was validated by the reference concentration of COD. The difference of COD predictions against references was within the same deviation of TOC-predictions. The modeled yield losses and retention values of TOC in pulping and bleaching processes and the modeled fixing of colloidal TOC to solids between the pulping plant and the aeration basin in the waste water treatment plant were similar to references presented in literature. The valid water balances of the waste water treatment plant and the reduction model of lignin-like substances produced a valid prediction of COD discharges out of the mill. A 30% increase in the release of lignin-like substances in the form of production problems was observed in pulping and bleaching processes. The same increase was observed in COD discharges out of waste water treatment. In the prediction of annual COD discharge, it was noticed that the reduction of lignin has a wide deviation from year to year and from one mill to another. This made it difficult to compare the parameters of COD discharges validated in plant dynamic simulation with another mill producing mechanical printing papers. However, a trend of moving from unbleached towards high-brightness TMP in COD discharges was valid.

A speculative systems model of the dynamic interaction among students, faculty and administration in the community college, with particular reference to intrinsic motivation and the teacher-administrator interface

The challenge the community college faces in helping meet the needs of the living open system of society is examined in this study. It is postulated that internalization student outcomes are required by society to reduce entropy and remain self-renewing. Such behavior is characterized as having an intrinsically motivated energy source and displays the seeking and conquering of challenge, the development of reflective knowledge and skill, full use of all capabilities, internal control, growth orientation, high self-esteem, relativistic thinking and competence. The development of a conceptual systems model that suggests how transactions among students, faculty and administration might occur to best meet the needs of internalization outcomes in students, and intrinsic motivation in faculty is a major purpose of this study. It is a speculative model that is based on a synthesis of a wide variety of variables. Empirical evidence, theoretical considerations, and speculative ideas are gathered together from researchers and theoretici.ans who are working on separate answers to questions of intrinsic motivation, internal control and environments that encourage their development. The model considers the effect administrators·have on faculty anq the corresponding effect faculty may have on students. The major concentration is on the administrator--teacher interface.For administrators the model may serve as a guide in planning effective transactions, and establishing system goals. The teacher is offered a means to coordinate actions toward a specific overall objective, and the administrator, teacher and researcher are invited to use the model to experiment, innovate, verify the assumptions on which the model is based, and raise additional hypotheses. Goals and history of the community colleges in Ontario are examined against current problems, previous progress and open system thinking. The nature of the person as a five part system is explored with emphasis on intrinsic motivation. The nature, operation, conceptualization, and value of this internal energy source is reviewed in detail. The current state of society, education and management theory are considered and the value of intrinsically motivating teaching tasks together with "system four" leadership style are featured. Evidence is reviewed that suggests intrinsically motivated faculty are needed, and "system four" leadership style is the kind of interaction-influence system needed to nurture intrinsic motivation in faculty.

Recent Glacier Retreat Exceeds Internal Variability

Glacier fluctuations exclusively due to internal variations in the climate system are simulated using downscaled integrations of the ECHAM4/OPYC coupled general circulation model (GCM). A process-based modeling approach using a mass balance model of intermediate complexity and a dynamic ice flow model considering simple shearing flow and sliding are applied. Multimillennia records of glacier length fluctuations for Nigardsbreen (Norway) and Rhonegletscher (Switzerland) are simulated using autoregressive processes determined by statistically downscaled GCM experiments. Return periods and probabilities of specific glacier length changes using GCM integrations excluding external forcings such as solar irradiation changes, volcanic, or anthropogenic effects are analyzed and compared to historical glacier length records. Preindustrial fluctuations of the glaciers as far as observed or reconstructed, including their advance during the “Little Ice Age,” can be explained by internal variability in the climate system as represented by a GCM. However, fluctuations comparable to the present-day glacier retreat exceed any variation simulated by the GCM control experiments and must be caused by external forcing, with anthropogenic forcing being a likely candidate.

Columnar joints in the Patino Formation sandstones, Eastern Paraguay: a dynamic interaction between dyke intrusion, quartz dissolution and cooling-induced fractures

The Patino Formation sandstones, which crop out in Aregua neighborhood in Eastern Paraguay and show columnar joints near the contact zone with a nephelinite dyke, have as their main characteristics the high proportion of syntaxial quartz overgrowth and a porosity originated from different processes, initially by dissolution and later by partial filling and fracturing. Features like the presence of floating grains in the syntaxial cement, the transitional interpenetrative contact between the silica-rich cement and grains as well as the intense fracture porosity are strong indications that the cement has been formed by dissolution and reprecipitation of quartz from the framework under the effect of thermal expansion followed by rapid contraction. The increase of the silica-rich cement towards the dyke in association with the orthogonal disposition of the columns relative to dyke walls are indicative that the igneous body may represent the main heat source for the interstitial aqueous solutions previously existing in the sediments. At macroscopic scale, the increasing of internal tensions in the sandstones is responsible for the nucleation of polygons, leading to the individualization of prisms, which are interconnected by a system of joints, formed firstly on isotherm surfaces of low temperature and later on successive adjacent planes towards the dyke heat source.

Estimation and evaluation of dynamic properties as indicators of changes on soil structure in sugarcane fields of São Paulo State - Brazil

The indiscriminate management and use of soils without moisture control has changed the structure of it due to the increment of the traffic by agricultural machines through the years, causing in consequence, a soil compaction and yield reduction in the areas of intensive traffic. The purpose of this work was to estimate and to evaluate the performance of preconsolidation pressure of the soil and shear stress as indicators of changes on soil structure in fields cropped with sugarcane, as well as the impact of management processes in an Eutrorthox soil structure located in São Paulo State. The experimental field was located in Piracicaba's rural area (São Paulo State, Brazil) and has been cropped with sugarcane, in the second harvest cycle. The soil was classified by Empresa Brasileira de Pesquisa Agropecuária (EMBRAPA) [Empresa Brasileira de Pesquisa Agropecuária (EMBRAPA), 1999. Centro Nacional de Pesquisa de Solos. Sistema Brasileiro de Classificao de Solos, Empresa Brasileira de Pesquisa Agropecuária (EMBRAPA), Brasilia, 412 pp.] as an Eutrorthox. Undisturbed samples were collected and georeferenced in a grid of 60 m x 60 m from two depths: 0-0.10 m (superficial layer - SL) and in the layer of greatest mechanical resistance (LGMR), previously identified by cone index (CI). The investigated variables were pressure preconsolidation (sigma(p)), apparent cohesion (c) and internal friction angle (phi). The conclusions from the results were that the SLSC was predicted satisfactorily from up as a function of soil moisture; thus, decisions about machinery size and loading (contact pressures) can be taken. Apparent cohesion (c), internal friction angle (phi) and the Coulomb equation were significantly altered by traffic intensity. The sigma(p), c and phi maps were shown to be important tools to localize and visualize soil compaction and mechanical resistance zones. They constitute a valuable resource to evaluate the traffic impact in areas cropped with sugarcane in State of São Paulo, Brazil. (C) 2008 Elsevier B.V. All rights reserved.

Prediction of Soil Properties from the Concepts of Energy Transfer in Dynamic Penetration Tests

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)