LD 侧面抽运Nd :YAG陶瓷激光器运转条件下归一化热参数优化理论及实验研究

The suppressing effect of laser extraction on the non-radiation transition process is taken into account when the heat model of gain media is developed. Based on the developed heat model, the heat generation in the operating LD side-pumped Nd: YAG ceramic lasers is quantified through using the normalized heating parameter, which can be deduced from the experimental results of the slope efficiency and the absorbed pumping power of the gain media. The main factors which influence on the heat generation are investigated by studying the normalized heating parameter, and the results show that the changes of the laser extraction efficiency, the beam overlap efficiency and the Nd3+ concentration will result in obvious variations of the normalized heating parameter. In this work, the laser extraction efficiency increases to 0.905 by the optimization of the transmission of the output coupling, and the normalized heating parameter decrease to 0.474, correspondingly.

LD抽运的Nd：YLF／Cr^4＋：YAG被动调Q激光器

报道了激光二极管（LD）抽运的Nd：YLF激光器，采用平凹腔结构，分别用两片Cr^4＋：YAG可饱和吸收晶体，实现了被动调Q，输出激光波长为1053nm。采用厚度为0．5mm小信号透过率为90％的Cr^4＋ YAG，在泵浦功率最大为17W时，输出脉冲宽度为60．6ns，平均功率为1．5W，重复频率为9．5kHz，单脉冲能量为157．9mJ；采用厚度为0．55mm小信号透过率为95％的Cr^4＋ YAG，在泵浦功率最大为17W时，输出脉冲宽度为68．6ns，平均功率为1．35W，重复频率为14kHz，单脉冲

LD侧面泵浦固体激光器泵浦光分布模拟

利用Gauss光束通过光学系统的变换规律,将激光二极管阵列发出的光作为Gauss光束处理.应用矩阵光学方法,解析分析与数值模拟相结合,给出了激光二极管阵列侧面泵浦棒状固体激光介质内泵浦光的强度分布.比较了侧面环绕激光二极管阵列数量不同时泵浦光分布的均匀性;以及考虑准直系统后,不同准直透镜焦距时,晶体内泵浦光半径的大小;同时针对泵浦光在晶体内聚焦时的情况进行了简单讨论.将半解析法与光线追迹法所得结果进行了比较,二者十分相近,但前者计算要简单得多.

连续可调纳秒脉冲LD驱动电源的研制

为了满足单模尾纤输出脉冲半导体激光器及其后级光放大的要求,研制了一种重频、脉宽及峰值电流均连续可调的纳秒脉冲驱动电源。该电源使用功率场效应管作为开关,通过分析其驱动特性,采用合适的栅极驱动电路,从而缩短了脉冲宽度,增加了带负载能力;同时电源中的保护电路采用自断电等保护措施,能有效保证LD的安全工作。实验结果表明,该驱动电源工作稳定,能满足单模尾纤输出脉冲LD重频、脉宽、峰值可调的要求。

LD泵浦的镱铒共掺磷酸盐玻璃的光谱性质和激光性质

制备了Er^3＋/Yb^3＋共掺磷酸盐玻璃. 通过分析其吸收光谱, 根据McCumber理论计算得到了Er^3＋离子在波长1533 nm处的峰值发射截面为0.84×10^-20 cm^2, ^4I13/2能级的荧光寿命为8.5 ms. 利用激光二极管作为泵浦源, 成功地实现了Er^3＋/Yb^3＋共掺磷酸盐玻璃激光器的连续运转. 在室温下, 获得最大激光输出功率为80 mW, 斜率效率为16.5%.

LD抽运Yb:GSO实现1090nm低阈值激光运转

We report what we believe to be the first demonstration of laser operation with a novel laser material of Yb3(+) -doped Gd-2 SiO2 (Yb: GSO) pumped by a laser diode at 940 nm. We obtained a low lasing threshold of 1.27 kW/cm(2) with the center wavelength of 1090 nm, which is lower than the value of 1.53 kW/cm(2) predicted for Yb: YAG. The maximal output power of 360 mW was obtained with a 2% output, which corresponds to a slope efficiency up to 19%.

LD抽运新型Yb：LYSO晶体实现1085nm激光输出

Yb^3＋激光材料在900～980nm范围具有较强的吸收，能与高效的InGaAs激光二极管（波长为9001100nm）有效地耦合，且能级简单，抽运波长与振荡波长相近，量子效率高。这些优点十分有利于在1000nm附近实现超快高功率激光输出。而随着高性能InGaAs激光二极管的发展和成本的降低，近年来，掺Yb^3＋激光介质的研究受到人们的极大关注，并研制出了许多新型激光晶体，如Yb：YAG，Yb：KYW，Yb：GdVO4，Yb：SYS，Yb：YAB，

叠层LD光纤光导椎泵浦光纤激光器的制作方法

一种叠层LD光纤光导椎泵浦光纤激光器的制作方法，其特征在于，包括如下步骤:步骤1:采用光学微加工工艺在石英或特种玻璃材料上加工制作光导椎，该光导椎为条状的六面体，其纵向一端的断面为斜向，且制作有光纤凹槽，纵向另一端的断面为bar条面;步骤2:在光导椎的光纤凹槽上依次并排固接有多个包层光纤;步骤3:在最外侧的包层光纤的外侧粘接一铜片;步骤4:在铜片上镀高反射率金膜;步骤5:将条状六面体的光导椎除光纤凹槽和bar条面外，其余四面全部镀高反射率金膜。

LD side-pumped high beam quality passive Q-switched and mode-locked Nd:YAG laser based on SESAM

We report a LD side-pumped fundamental-mode (Mx(2) = 1.35 and My(2) = 1.27) passive Q-switched and mode-locked Nd:YAG laser based on a semiconductor saturable absorber mirror (SESAM). At a pump current of 12.5 A, the average output power of 5.68 W with 80 kHz repetition rate and 2 mu s pulse width of the Q-switched envelope was generated. The repetition rate of the mode-locked pulse within the Q-switched envelope of 88 MHz was achieved.