Feedforward Control of Shape Memory Alloy Actuators Using Fuzzy-Based Inverse Preisach Model

This brief investigates a possible application of the inverse Preisach model in combination with the feedforward and feedback control strategies to control shape memory alloy actuators. In the feedforward control design, a fuzzy-based inverse Preisach model is used to compensate for the hysteresis nonlinearity effect. An extrema input history and a fuzzy inference is utilized to replace the inverse classical Preisach model. This work allows for a reduction in the number of experimental parameters and computation time for the inversion of the classical Preisach model. A proportional-integral-derivative (PID) controller is used as a feedback controller to regulate the error between the desired output and the system output. To demonstrate the effectiveness of the proposed controller, real-time control experiment results are presented.

Position control of shape memory alloy actuators using self tuning fuzzy PID controller

Shape Memory Alloy (SMA) actuators, which have the ability to return to a predetermined shape when heated, have many potential applications such as aeronautics, surgical tools, robotics and so on. Although the conventional PID controller can be used with slow response systems, there has been limited success in precise motion control of SMA actuators, since the systems are disturbed by unknown factors beside their inherent nonlinear hysteresis and changes in the surrounding environment of the systems. This paper presents a new development of a SMA position control system by using a self-tuning fuzzy PID controller. This control algorithm is used by tuning the parameters of the PID controller thereby integrating fuzzy inference and producing a fuzzy adaptive PID controller, which can then be used to improve the control performance of nonlinear systems. The experimental results of position control of SMA actuators using conventional and self-tuning fuzzy PID controllers are both included in this paper.

Tracking Human Position and Lower Body Parts Using Kalman and Particle Filters Constrained by Human Biomechanics

In this paper, a novel framework for visual tracking of human body parts is introduced. The approach presented demonstrates the feasibility of recovering human poses with data from a single uncalibrated camera by using a limb-tracking system based on a 2-D articulated model and a double-tracking strategy. Its key contribution is that the 2-D model is only constrained by biomechanical knowledge about human bipedal motion, instead of relying on constraints that are linked to a specific activity or camera view. These characteristics make our approach suitable for real visual surveillance applications. Experiments on a set of indoor and outdoor sequences demonstrate the effectiveness of our method on tracking human lower body parts. Moreover, a detail comparison with current tracking methods is presented.

Variable selection via RIVAL and its application in nuclear material detection

In many situations, the number of data points is fixed, and the asymptotic convergence results of popular model selection tools may not be useful. A new algorithm for model selection, RIVAL (removing irrelevant variables amidst Lasso iterations), is presented and shown to be particularly effective for a large but fixed number of data points. The algorithm is motivated by an application of nuclear material detection where all unknown parameters are to be non-negative. Thus, positive Lasso and its variants are analyzed. Then, RIVAL is proposed and is shown to have some desirable properties, namely the number of data points needed to have convergence is smaller than existing methods.

Towards identification of Wiener systems with the least amount of a priori information on the nonlinearity

In this paper, we investigate what constitutes the least amount of a priori information on the nonlinearity so that the FIR linear part is identifiable in the non-Gaussian input case. Three types of a priori information are considered including quadrant information, point information and locally monotonous information. In all three cases, identifiability has been established and corresponding identification algorithms are developed with their convergence proofs.

Nakagami-m Phase Model: Further Results and Validation

This paper contributes to and expands on the Nakagami-m phase model. It derives exact, closed-form expressions for both the phase cumulative distribution function and its inverse. In addition, empirical first- and second-order statistics obtained from measurements conducted in a body-area network scenario were used to fit the phase probability density function, the phase cumulative distribution function, and the phase crossing rate expressions. Remarkably, the unlikely shapes of the phase statistics, as predicted by the theoretical formulations, are actually encountered in practice.

A theoretical assessment of surface defect machining and hot machining of nanocrystalline silicon carbide

In this paper, a newly proposed machining method named “surface defect machining” (SDM) [Wear, 302, 2013 (1124-1135)] was explored for machining of nanocrystalline beta silicon carbide (3C-SiC) at 300K using MD simulation. The results were compared with isothermal high temperature machining at 1200K under the same machining parameters, emulating ductile mode micro laser assisted machining (µ-LAM) and with conventional cutting at 300 K. In the MD simulation, surface defects were generated on the top of the (010) surface of the 3C-SiC work piece prior to cutting, and the workpiece was then cut along the <100> direction using a single point diamond tool at a cutting speed of 10 m/sec. Cutting forces, sub-surface deformation layer depth, temperature in the shear zone, shear plane angle and friction coefficient were used to characterize the response of the workpiece. Simulation results showed that SDM provides a unique advantage of decreased shear plane angle which eases the shearing action. This in turn causes an increased value of average coefficient of friction in contrast to the isothermal cutting (carried at 1200 K) and normal cutting (carried at 300K). The increase of friction coefficient however was found to aid the cutting action of the tool due to an intermittent dropping in the cutting forces, lowering stresses on the cutting tool and reducing operational temperature. Analysis shows that the introduction of surface defects prior to conventional machining can be a viable choice for machining a wide range of ceramics, hard steels and composites compared to hot machining.

Virtual metrology enabled early stage prediction for enhanced control of multi-stage fabrication processes

Semiconductor fabrication involves several sequential processing steps with the result that critical production variables are often affected by a superposition of affects over multiple steps. In this paper a Virtual Metrology (VM) system for early stage measurement of such variables is presented; the VM system seeks to express the contribution to the output variability that is due to a defined observable part of the production line. The outputs of the processed system may be used for process monitoring and control purposes. A second contribution of this work is the introduction of Elastic Nets, a regularization and variable selection technique for the modelling of highly-correlated datasets, as a technique for the development of VM models. Elastic Nets and the proposed VM system are illustrated using real data from a multi-stage etch process used in the fabrication of disk drive read/write heads. © 2013 IEEE.

Kernel-based local order estimation of nonlinear nonparametric systems

We consider the local order estimation of nonlinear autoregressive systems with exogenous inputs (NARX), which may have different local dimensions at different points. By minimizing the kernel-based local information criterion introduced in this paper, the strongly consistent estimates for the local orders of the NARX system at points of interest are obtained. The modification of the criterion and a simple procedure of searching the minimum of the criterion, are also discussed. The theoretical results derived here are tested by simulation examples.

An ultra-short-term wind power prediction method using “offline classification and optimization, online model matching” based on time series features

The applicability of ultra-short-term wind power prediction (USTWPP) models is reviewed. The USTWPP method proposed extracts featrues from historical data of wind power time series (WPTS), and classifies every short WPTS into one of several different subsets well defined by stationary patterns. All the WPTS that cannot match any one of the stationary patterns are sorted into the subset of nonstationary pattern. Every above WPTS subset needs a USTWPP model specially optimized for it offline. For on-line application, the pattern of the last short WPTS is recognized, then the corresponding prediction model is called for USTWPP. The validity of the proposed method is verified by simulations.

Integrating control and electronics

Previously the author described how control engineering can be introduced using little mathematics in a first year course, the aim being to make the subject accessible across different degrees. One reaction to this was that it was a good idea, but there was not space to include it in the curriculum where, typically control engineering is not introduced until the second year. This paper describes how the author has used a review of the first year teaching to develop a module in which feedback, control and electronics are integrated coherently. This is beneficial as concepts in control and electronics mutually reinforce each other. This has been achieved during a reduction in the available time for teaching the material. This paper describes the strategy used to successfully develop the module, the integrated module and positive student reaction.

Dynamic method of stiffness identification in impacting systems for percussive drilling applications

Peer reviewed