Estudo de espécie nativa da restinga para plantio em telhados de construção de interesse social.

O alto crescimento populacional tem desencadeado uma elevada ocupação das áreas urbanas com a expansão de edificações e estradas causando alterações no meio ambiente com a consequente minimização das áreas verdes e da infiltração de água no solo. Estes fenômenos acarretam problemas como enxurradas, inundações, aumento da temperatura local e diminuição da biodiversidade com inúmeros efeitos adversos, tanto econômicos quanto ambientais e sociais. Uma das alternativas para minimizar estes problemas é a construção de telhados verdes, que tem como uma das principais funções retardar o escoamento devido ao aumento da infiltração e retenção da água das chuvas atenuando o efeito avassalador das enchentes e das zonas de calor, principalmente em climas muito quentes, além de colaborar para recuperação de ecossistemas, através do replantio de mudas. Este projeto faz parte de um conjunto de ações integradas de cidadania e inclusão social na região hidrográfica da baixada de Jacarepaguá, especificamente envolvendo a Comunidade da Vila Cascatinha, em Vargem Grande, a fim de gerar subsídios para políticas públicas em áreas de assentamentos informais, integrado ao projeto HIDROCIDADES (CNPq, FAPERJ, FINEP), que visa a conservação da água em meios urbanos e periurbanos associado à cidadania, inclusão social e melhoria da qualidade de vida nas grandes cidades. Este trabalho utiliza uma tecnologia adaptada dos telhados verdes para edificação popular (telhado de fibrocimento) muito comum no Brasil, com o objetivo de verificar uma espécie com potencial de geração de renda (visando o social) de ecossistema regionais como restinga, em edificação; analisar o crescimento e biomassa da espécie de restinga cultivada em telhados; e avaliar qualidades das mídias em função do plantio em análise de armazenamento (retenção) de água no solo. A partir da metodologia empregada na implantação dos telhados verdes em habitações populares, os resultados obtidos são desenvolvimento da espécie Ipomoea pes caprae Brasiliensis, em três tipos de mídias de crescimento e também eficiência dessas mídias no escoamento superficial. Observou-se retenção de 69,24L de água para o bagaço de cana de açúcar e 64,7L para a fibra de coco. E foi observado também um retardo da ocorrência do pico de até 14 minutos no telhado vegetado em relação ao telhado controle (convencional).

Estudo da Delaminação em Compósitos de Epóxido Reforçado com Borracha e Fibras Naturais

Nos últimos anos, a utilização dos materiais compósitos tem vindo a tornar-se cada vez mais comum em várias indústrias, onde se verifica uma ascensão na procura pelos mesmos. Características como o baixo peso aliado à sua alta resistência e rigidez permitem que estes materiais possuam diversas aplicações em variadas áreas, desde a medicina, aeronáutica, indústria automóvel e aeroespacial, até à indústria eletrónica. Hoje em dia, o uso de desperdícios sólidos de borracha e fibras naturais na produção de materiais compósitos é, mais que uma opção, uma necessidade ambiental. De forma a reduzir as enormes quantidades de desperdícios, foi criado um material compósito constituído por uma resina termoendurecível reforçada com esses dois tipos de desperdícios. Parâmetros de fabrico como a percentagem de borracha, o tamanho das partículas de borracha, a percentagem de fibras de cana-de-açúcar e o comprimento dessas fibras foram variados, com o objetivo de estudar a influência destes dois materiais nas propriedades mecânicas do compósito. Apesar da maior parte dos compósitos serem fabricados na forma de uma peça funcional quase pronta a ser utilizada, por vezes é necessário recorrer à maquinação de furos. Apesar das muitas técnicas de furação existentes, os defeitos resultantes deste processo aplicado aos materiais compósitos são ainda muito comuns. Desses defeitos o que mais se destaca é sem dúvida a delaminação. Trinta e seis provetes de epóxido reforçado com borracha e fibra de cana-de-açúcar foram fabricados e furados, de modo a possibilitar o estudo das propriedades mecânicas do material compósito, assim como a análise da zona danificada durante a furação. Diferentes condições de furação, como tipos de broca e velocidades de avanço diferentes, foram impostas aos provetes de forma a variar o mais possível a zona de dano de uns furos para os outros. Parâmetros como a área de dano ou ainda o fator de delaminação provam ser muito úteis na caracterização e quantificação do dano na zona periférica de um furo. Recorrendo a técnicas de processamento de imagem foi possível obter esses parâmetros. O processamento e análise de imagem pode ser feito através de vários métodos. O método utilizado neste trabalho foi o software MATLAB® associado a ferramentas de processamento de imagem. Depois de feita a análise dos furos foram realizados ensaios de esmagamento a todos os provetes. Este passo permitiu assim avaliar de que forma os parâmetros de furação influenciam a resistência mecânica do material, e se a avaliação realizada aos furos é um método viável para a avaliação da extensão de dano nesses furos.

Studies on Landfill Leachate Transportation and Its Impact on Soil Characteristics

Leachate from an untreated landfill or landfill with damaged liners will cause the pollution of soil and ground water. Here an attempt was made to generate knowledge on concentrations of all relevant pollutants in soil due to municipal solid waste landfill leachate and its migration through soil and also to study the effect of leachate on the engineering properties of soil. To identify the pollutants in soil due to the leachate generated from municipal solid waste landfill site, a case study on an unlined municipal solid waste landfill at Kalamassery has been done. Soil samples as well as water samples were collected from the site and analysed to identify the pollutants and its effect on soil characteristics. The major chemicals in the soil were identified as Ammonia, Chloride, Nitrate, Iron, Nickel, Chromium, Cadmium etc.. Engineering properties of field soil samples show that the chemicals from the leachate of landfill may have effect on the engineering properties of soil. Laboratory experiments were formulated to model the field around an unlined MSW landfill using two different soils subjected to a synthetic leachate. The Maximum change in chemical concentration and engineering property was observed on soil samples at a radial distance of 0.2 m and at a depth of 0.3 m. The pollutant (chemicals) transport pattern through the soil was also studied using synthetic leachate. To establish the effect of pollutants (chemicals) on engineering properties of soil, experiments were conducted on two types soils treated with the synthetic chemicals at four different concentrations. Analyses were conducted after maturing periods of 7, 50, 100 and 150 days. Test soils treated with maximum chemical concentration and matured for 150 days were showing major change in the properties. To visualize the flow of pollutants through soil in a broader sense, the transportation of pollutants through soil was modeled using software ‘Visual MODFLOW’. The actual field data collected for the case study was used to calibrate the modelling and thus simulated the flow pattern of the pollutants through soil around Kalamassery municipal solid waste landfill for an extent of 4 km2. Flow was analysed for a time span of 30 years in which the landfill was closed after 20 years. The concentration of leachate beneath the landfill was observed to be reduced considerably within one year after closure of landfill and within 8 years, it gets lowered to a negligible level. As an environmensstal management measure to control the pollution through leachate, permeable reactive barriers are used as an emerging technology. Here the suitability of locally available materials like coir pith, rice husk and sugar cane bagasse were investigated as reactive media in permeable reactive barrier. The test results illustrates that, among these, coir pith was showing better performance with maximum percentage reduction in concentration of the filtrate. All these three agricultural wastes can be effectively utilized as a reactive material. This research establishes the influence of leachate of municipal solid waste landfill on the engineering properties of soil. The factors such as type of the soil, composition of leachate, infiltration rate, aquifers, ground water table etc., will have a major role on the area of influence zone of the pollutants in a landfill. Software models of the landfill area can be used to predict the extent and the time span of pollution of a landfill, by inputting the accurate field parameters and leachate characteristics. The present study throws light on the role of agro waste materials on the reduction of the pollution in leachate and thus prevents the groundwater and soil from contamination

Phenol-furfural resins to elaborate composites, reinforced with sisal fibers - Molecular analysis of resin and properties of composites

Resol type resins were prepared in alkaline conditions (potassium hydroxide or potassium carbonate) using furfural obtained by acid hydrolysis of abundant renewable resources from agricultural and forestry waste residues. The structures of the resins were fully determined by H-1, C-13, and 2D NMR spectrometries with the help of four models compounds synthesized specially for this study. MALDI-Tof mass spectrometry experiments indicated that a majority of linear oligomers and a minority of cyclic ones constituted them. Composites were prepared with furfural-phenol resins and sisal fibers. These fibers were chosen mainly because they came from natural lignocellulosic material and they presented excellent mechanical microscopy images indicated that the composites displayed excellent adhesion between resin and fibers. Impact strength measurement showed that mild conditions were more suitable to prepare thermosets. Nevertheless, mild conditions induced a high-diffusion coefficient for water absorption by composites. Composites with good properties could be prepared using high proportion of materials obtained from biomass without formaldehyde. (c) 2008 Wiley Periodicals, Inc.

Ionized-air-treated curaua fibers as reinforcement for phenolic matrices

Curaua fibers were treated with ionized air to improve the fiber/phenolic matrix adhesion.The treatment with ionized air did not change the thermal stability of the fibers. The impact strength increased with increase in the fiber treatment time. SEM micrographs of the fibers showed that the ionized air treatment led to separation of the fiber bundles. Treatment for 12 h also caused a partial degradation of the fibers, which prompted the matrix to transfer the load to a poorer reinforcing agent during impact, thereby decreasing the impact strength of the related composite. The composites reinforced with fibers treated with ionized air absorbed less water than those reinforced with untreated fibers.

Surface esterification of cellulose fibres: Processing and characterisation of low-density polyethylene/cellulose fibres composites

Low-density polyethylene was filled with cellulose fibres from sugar cane bagasse obtained from organosolv/supercritical carbon dioxide pulping process. The fibres were also used after chemical modification with octadecanoyl and dodecanoyl chloride acids. The morphology, thermal properties, mechanical properties in both the linear and nonlinear range, and the water absorption behaviour of ensuing composites were tested. The evidence of occurrence of the chemical modification was checked by X-ray photoelectron spectrometry. The degree of polymerisation of the fibres and their intrinsic properties (zero tensile strength) were determined. It clearly appeared that the surface chemical modification of cellulose fibres resulted in improved interfacial adhesion with the matrix and higher dispersion level. However, composites did not show improved mechanical performances when compared to unmodified fibres. This surprising result was ascribed to the strong lowering of the degree of polymerisation of cellulose fibres (as confirmed by the drastic decrease of their zero tensile strength) after chemical treatment despite the mild conditions used. (c) 2007 Elsevier Ltd. All rights reserved.

Biobased composites from tannin-phenolic polymers reinforced with coir fibers

Tannin-phenolic polymers prepared using tannin, a macromolecule obtained from natural sources, were used in the preparation of composites reinforced with coir fibers. The composites based on tannin-phenolic polymers (50% (w/w) of tannin as substitute of the phenol) were prepared using the coir fibers as reinforcement (30-70% (w/w), 3.0-6.0 cm, randomly distributed). The Izod impact strength of the composites showed an improvement in this property due to the incorporation of coir fibers in the tannin-phenolic matrices. The SEM images showed excellent adhesion at the fiber/matrix interface. The coir fiber had bundles regularly spaced, which enhanced the diffusion of the resin into the fiber. In addition, the high lignin content of this fiber results in a high concentration of aromatic rings, which increased the compatibility with the matrix. The values of the diffusion coefficient of water, determined using Fick`s laws, show that there was no correlation between the fiber percentage and the water diffusion. The DMTA curves showed that the storage moduli of the composites reinforced with coir fibers were considerably higher than that of the thermoset, and the increase in the proportion of fibers led to a proportional increase in the storage moduli of these materials. The biobased composites obtained have potential for non-structural applications, such as in the internal parts of automotives vehicles. To our knowledge, this is the first study on this kind of biobased composites. (C) 2010 Elsevier B.V. All rights reserved.

Biobased composites from glyoxal-phenolic resins and sisal fibers

Lignocellulosic materials can significantly contribute to the development of biobased composites. In this work, glyoxal-phenolic resins for composites were prepared using glyoxal, which is a dialdehyde obtained from several natural resources. The resins were characterized by (1)H, (13)C, (2)D, and (31)P NMR spectroscopies. Resorcinol (10%) was used as an accelerator for curing the glyoxal-phenol resins in order to obtain the thermosets. The impact-strength measurement showed that regardless of the cure cycle used, the reinforcement of thermosets by 30% (w/w) sisal fibers improved the impact strength by one order of magnitude. Curing with cycle 1 (150 degrees C) induced a high diffusion coefficient for water absorption in composites, due to less interaction between the sisal fibers and water. The composites cured with cycle 2 (180 degrees C) had less glyoxal resin coverage of the cellulosic fibers, as observed by images of the fractured interface observed by SEM. This study shows that biobased composites with good properties can be prepared using a high proportion of materials obtained from natural resources. (C) 2009 Elsevier Ltd. All rights reserved.

Phenolic matrices and sisal fibers modified with hydroxy terminated polybutadiene rubber: Impact strength, water absorption, and morphological aspects of thermosets and composites

The aim of the present work was to investigate the toughening of phenolic thermoset and its composites reinforced with sisal fibers, using hydroxyl-terminated polybutadiene rubber (HTPB) as both impact modifier and coupling agent. Substantial increase in the impact strength of the thermoset was achieved by the addition 10% of HTPB. Scanning electron microscopy (SEM) images of the material with 15% HTPB content revealed the formation of some rubber aggregates that reduced the efficiency of the toughening mechanism. In composites, the toughening effect was observed only when 2.5% of HTPB was added. The rubber aggregates were found located mainly at the matrix-fiber interface suggesting that HTPB could be used as coupling agent between the sisal fibers and the phenolic matrix. A composite reinforced with sisal fibers pre-impregnated with HTPB was then prepared; its SEM images showed the formation of a thin coating of HTPB on the surface of the fibers. The ability of HTBP as coupling agent between sisal fibers and phenolic matrix was then investigated by preparing a composite reinforced with sisal fibers pre-treated with HTPB. As revealed by its SEM images, the HTPB pre-treatment of the fibers resulted on the formation of a thin coating of HTPB on the surface of the fibers, which provided better compatibility between the fibers and the matrix at their interface, resulting in a material with low water absorption capacity and no loss of impact strength. (C) 2009 Elsevier B.V. All rights reserved.

Adição do resíduo de biomassa da cana-de-açúcar em pastas para cimentação de poços petrolíferos produtores de óleos pesados

The Potiguar basin has large fields of viscous oil where the used method for recovering is based on vapor injection; this operation is carried out by injecting vapor in the oilwell directly, without the protection of a revetment through thermal insulation, what causes its dilation and, consequently, cracks in the cement placed on the annular, and lost of hydraulic insulation; this crack is occasioned by the phenomenon of retrogression of the compressive resistance due to the conversion of the hydrated calcium silicate in phases calcium-rich, caused by the high temperatures in the wells, subjected to thermal recuperation. This work has evaluated the application of composite pastes with addition of residue of biomass of ground sugar-cane bagasse as anti-retrogression mineral admixture for cementation of oil-wells subjected to thermal recuperation. The addition of the mineral residue was carried out considering a relative amount of 10, 20, 30, 40 and 59% in relation to cement mass, trying to improve the microstructure of the paste, still being developed a reference paste only with cement and a paste with addition of 40% of silica flour - renowned material in the oil industry as anti-retrogression additive. Pozzolanic activity of the ash was evaluated through XRD, TG/DTG, as the resistance to compression, and it was also determined the physical and mechanical behavior of the pastes when submitted to cure at low temperatures (22 and 38º C); besides it was evaluated the behavior of the pastes when submitted to two cycles of cure at high temperature (280ºC) and pressure (7 MPa). It was verified that the ash of the sugar-cane biomass presents pozzolanic reaction and has great efficiency in decrease the permeability of the paste by filler effect, as well as that addition of ash in a relative amount of 10, 20 e 30% increases cured compressive resistance at low temperatures. It was also showed that the ash in a relative amount of 40% and 59% has very significant efficiency as anti-retrogression additive, since it prevents the decrease of compressive resistance and forms hydrated calcium silicate type xenotlita and tobermorita which have more resistance and stability in high temperatures

Produção de Bipolaris euphorbiae em meios de cultura sólidos e líquidos obtidos de grãos e resíduos agroindustriais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Bagaço de cana-de-açúcar tratado com hidróxido de sódio

O experimento foi conduzido com o objetivo de avaliar a composição química e a digestibilidade in vitro da matéria seca (MS) do bagaço de cana-de-açúcar contendo 60% de MS submetido a doses crescentes de hidróxido de sódio (NaOH) (0; 2,5; 5 e 7,5% de uma solução 2:1 de água:NaOH na MS) em diferentes períodos de tratamento (1, 3, 5 e 7 dias). Foram utilizados baldes plásticos com capacidade de 10 L, mantidos em uma câmara climática à temperatura constante de 25ºC. Não foi verificado efeito dos tratamentos (dose de NaOH e dias de tratamento) sobre os teores de PB, que apresentaram valor médio de 1,6%. A MS aumentou com os dias de tratamento, não sendo observadas alterações para essa variável em relação às doses crescentes de NaOH. Foi observada redução das frações de FDN, FDA, celulose (CEL), hemicelulose (HEM) e lignina (LIG). A digestibilidade in vitro da matéria seca (DIVMS) e o teor de sódio aumentaram quando o bagaço de cana foi submetido a doses crescentes de NaOH, mas não foi observado efeito do período de tratamento sobre essas variáveis. O valor nutritivo do bagaço de cana é melhorado com a adição de NaOH, comprovado pela redução nos constituintes da parede celular e pelo aumento na DIVMS.

Desempenho e características de carcaça de bovinos Nelore em confinamento alimentados com bagaço de cana-de-açúcar e diferentes fontes energéticas

Avaliaram-se o ganho de peso e as características da carcaça de bovinos Nelore alimentados com bagaço de cana-de-açúcar (in natura ou hidrolisado) como volumoso e concentrado contendo farelo de gérmen de milho, casca do grão de soja ou polpa de citrus em substituição parcial (50%) ao milho. Quarenta bovinos Nelore (peso médio inicial de 340 kg e idade inicial de 32 meses) foram alimentados com quatro dietas fornecidas na proporção volumoso:concentrado 39:61. As fontes substitutivas do milho não afetaram o peso final (470,8; 478,6; 476,4 e 475,3 kg) e o ganho médio diário (1,1; 1,1; 1,1 e 1,2 kg/animal/dia). Não houve efeito sobre o rendimento de carcaça (55,3; 55,3; 54,0 e 54,8%), a área de Longissimus (24,2; 23,0; 25,0 e 23,2 cm²/100 kg de carcaça) e a espessura de gordura (4,4; 5,6; 4,7 e 4,4 mm). O menor custo por arroba foi observado no tratamento com polpa de citrus (R$ 44,20), seguido do farelo de gérmen de milho (R$ 48,80) e da casca de soja (R$ 50,80), porém, quando utilizado somente o milho, o custo da arroba foi de R$ 51,80. O milho moído pode ser parcialmente substituído pelo farelo de gérmen de milho, pela casca de soja ou pela polpa de citrus em dietas para bovinos em confinamento alimentados com bagaço de cana-de-açúcar (in natura ou hidrolisado) como volumoso, pois a substituição não alterou o ganho de peso e as características de carcaça.

Production of reinforced composites with natural fibers for industrial applications - Extrusion and injection WPC

The aim of this work is to study the replacement of currently used thermoplastics by composites reinforced with vegetable fibers with several advantages, mainly better mechanical properties, low weight and competitive cost compared to its counterparts. Extrusion and injection molding processes were studied using polypropylene (PP) matrix. The raw materials used were sugar cane bagasse, elephant grass, wood, milk cartons and recycled polypropylene. The composites were tested for bending, tension, hardness and impact resistance, following ASTM standards. The results obtained were extremely positive since they proved that natural fibers as reinforcement can be an important alternative to replace talc and other fillers.

Aproveitamento de resíduos de cinza da cana de açúcar em massas cerâmicas

This study aimed to investigate the use of cane sugar ashes from small-scale stills of Eunápolis region, state of Bahia, in pottery mass that can be developed as porcelain stoneware. Bahia is the second largest producer of rum distillery in Brazil. In the production of rum is produced residue called bagasse, which is used to generate electricity in Power plants and in the distillery itself, generating ashes as residue, which is played in nature, causing environmental damage. We studied 5 (five) formulations of 0% 10% 20%, 30% and 40% by weight of the ash, without ignition and 3 (three) formulations of 10%, 20% and 30% with gray ash temperature of 1250ºC. The formulation at 0% by weight of ash was used for a comparison between the traditional mass of porcelain stoneware and the masses with the addition of ash calcined, replacing feldspar. The percentage by weight of kaolin and of Clay was kept the same, 30%, and all raw materials were derived from the state of Bahia. The samples were made in uniaxial array with dimensions of (60 x 20 x 5) mm and compressed to a pressure of 45 MPa. Assays were performed to characterize the raw by X-ray fluorescence, X-ray diffraction, ATD and ATG and Dilatometric analysis. The samples were sintered at temperatures of 1100°C, 1150°C, 1200°C and 1250°C, for the specimens with the ashes without ash and 1150° C and 1200° C for specimens with the gray level of calcined 60 minutes. and then we made a cooling ramp with the same rate of warming until reach ambient temperature. The sintered bodies were characterized by water absorption, porosity, linear shrinkage, bending strength and XRD of the fracture surface and the results analyzed. It was proven, after results of tests performed, that it is possible to use the ash residue of sugar cane bagasse on ceramic coating with the addition of up to 10% wt of the residue ash