The effect of trace elements on the sintering of an Al-Zn-Mg-Cu alloy

Trace elements can have a significant effect on the processing and properties of aluminium alloys, including sintered alloys. As little as 0.07 wt% (100 ppm) lead, tin or indium promotes sintering in an Al-Zn-Mg-Cu alloy produced from mixed elemental powders. This is a liquid phase sintering system and thin liquid films form uniformly throughout the alloy in the presence of the trace elements, but liquid pools develop in their absence. Analytical transmission electron microscopy indicates that the trace elements are confined to the interparticle and grain boundary regions. The sintering enhancement is attributed to the segregation of the microalloying addition to the liquid-vapour interface. Because the microalloying elements have a low surface tension, they lower the effective surface tension of the liquid. This reduces the wetting angle and extends the spreading of the liquid through the matrix. An improvement in sintering results. (C) 2001 Acta Materialia Inc. Published by Elsevier Science Ltd. All rights reserved.

Mass balance characterisation of Al-7Si-Mg alloy microstructures as a function of solution treatment time

Mass balance calculations were performed to model the effect of solution treatment time on A356 and A357 alloy microstructures. Image analysis and electron probe microanalysis were used to characterise microstructures and confirm model predictions. In as-cast microstructures, up to 8 times more Mg is tied up in the pi-phase than in Mg2Si. The dissolution of pi is accompanied by a corresponding increase in the amount of beta-phase. This causes the rate of pi dissolution to be limited by the rate of beta formation. It is predicted that solution treatments of the order of tens of minutes at 540degreesC produce near-maximum T6 yield strengths, and that Mg contents in excess of 0.52 wt% have no advantage.

Powder forging of a sintered Al-3.8Cu-1Mg-0.8Si-O.1Sn alloy

The forging characteristics of an Al-Cu-Mg-Si-Sn alloy are examined using it new testing strategy which incorporates a double truncated cone specimen and finite element modelling. This sample geometry produces controlled strain distributions within a single specimen and can readily identify the specific strain required to achieve a specific microstructural event by matching the metallographic data with the strain profiles calculated from finite element software, The friction conditions were determined using the conventional friction ring test, which was evaluated using finite element software. The rheological properties of the alloy, evaluated from compression testing of right cylinders, are similar to the properties of conventional aluminium forgings. A hoop strain develops at the outer diameter of the truncated cones and this leads to pore opening at the outer few millimetres. The porosity is effectively removed when the total strain equals the net compressive strain. The strain profiles that develop in the truncated cones are largely independent of the processing temperature and the strain rate although the strain required for pore closure increases as the forging temperature is reduced. This suggests that the microstructure and the strain rate sensitivity may also be important factors controlling pore behaviour. (C) 2002 Elsevier Science B.V. All rights reserved.

Surface alloying of AZ91D alloy by diffusion coating

A new technique of surface modification by diffusion coating for AZ91D alloy was developed. A 1.0-2.0-mm alloy layer, which has hardness four to five times higher than the substrate metal, was formed after the treatment. Consequent solution treatment and aging could further improve the hardness of the alloy layer. Microstructure and chemical composition were investigated using optical microscope and electron probe.

Rapid genotyping of loci involved in antifolate drug resistance in Plasmodium falciparum by primer extension

Current methods used to genotype point mutations in Plasmodium falciparum genes involved in resistance to antifolate drugs include restriction digestion of PCR products, allele-specific amplification or sequencing. Here we demonstrate that known point mutations in dihydrofolate reductase and dihydropteroate synthase can be scored quickly and accurately by single-nucleotide primer extension and detection of florescent products on a capillary sequencer. We use this method to genotype parasites in natural infections from the Thai-Myanmar border. This approach could greatly simplify large-scale screening of resistance mutations of the type required for evaluating and updating antimalarial drug treatment policies. The method can be easily adapted to other P. falciparum genes and will greatly simplify scoring of point mutations in this and other parasitic organisms. © 2002 Australian Society for Parasitology Inc. Published by Elsevier Science Ltd. All rights reserved.

Las Memorias del duque de Sully (o los avatares del primer proyecto de unión europea)

El presente artículo se consagra al análisis de la redacción, edición y difusión de las Memorias del duque de Sully. Con ese propósito, la prim-era sección refiere el contexto que rodea la preparación de la obra; la segunda presenta las características generales de la confederación y la tercera profundiza en las discrepancias de sus versiones; en la cuarta, quinta y la sexta se estudian la cronología y las etapas de la redacción, los cambios operados en los manuscritos y sus vías de difusión; la séptima examina el debate sobre la primacía histórica de las Memorias. El artículo pretende reconstruir las condiciones que determinan la elaboración y recepción del primer proyecto paneuropeo.

Servicio civil en Chile, análisis de los directivos de primer nivel jerárquico (2003-13)

Resumen Este artículo analiza los principales factores que condicionan la selección de un directivo público de primer nivel jerárquico en Chile con base en una perspectiva de corte sociológico y el uso del concepto especies de capital. El trabajo realiza un recorrido teórico y descriptivo sobre la modernización del Estado y la profesionalización de la gestión pública en Chile. Posteriormente con una muestra de 45 casos correspondientes a altos directivos nombrados durante el período 2003-13, se trabaja con modelos de regresión logística para determinar los factores que condicionan la selección de estos funcionarios. Se llega a la conclusión que el capital político no es un factor que favorece la selección del actor.

Análisis de productividad, calidad y costos en laboratorios del primer nivel: la biometría hemática

OBJETIVO: Conocer el grado de eficiencia con la que funcionan los laboratorios clínicos del primer nivel mediante una evaluación que integre: la productividad, la calidad y los costos. MÉTODOS: Se seleccionaron 10 laboratorios clínicos de un total de 52 existentes en la Ciudad de México; se utilizó el modelo de Donabedian en sus componentes de estructura, proceso y resultado utilizando la biometría hemática como rastreador. RESULTADOS: Los principales problemas fueron: inadecuada distribución del recurso humano calificado; malas condiciones del material de vidrio; inadecuado proceso analítico y baja productividad. Estos problemas se reflejaron en un incremento de un 200% en los costos unitarios respecto al costo ideal. Solamente son confiables los resultados de 50% de los laboratorios analizados. Veinte porciento de los laboratorios analizados son eficientes. CONCLUSIONES: La solución a los problemas encontrados requiere de estrategias integrales que comprometen a diferentes ámbitos, por lo que su solución se plantea difícil. Se recomienda analizar el costo-beneficio de crear un laboratorio central y dejar a los demás laboratorios como sitios para la toma de muestras exclusivamente.

In-situ X-ray diffraction studies during growth of Ni-Ti shape memory alloy films and their complementary ex-situ characterization

Shape Memory Alloy (SMA) Ni-Ti films have attracted much interest as functional and smart materials due to their unique properties. However, there are still important issues unresolved like formation of film texture and its control as well as substrate effects. Thus, the main challenge is not only the control of the microstructure, including stoichiometry and precipitates, but also the identification and control of the preferential orientation since it is a crucial factor in determining the shape memory behaviour. The aim of this PhD thesis is to study the optimisation of the deposition conditions of films of Ni-Ti in order to obtain the material fully crystallized at the end of the deposition, and to establish a clear relationship between the substrates and texture development. In order to achieve this objective, a two-magnetron sputter deposition chamber has been used allowing to heat and to apply a bias voltage to the substrate. It can be mounted into the six-circle diffractometer of the Rossendorf Beamline (ROBL) at the European Synchrotron Radiation Facility (ESRF), Grenoble, France, enabling an in-situ characterization by X-ray diffraction(XRD) of the films during their growth and annealing. The in-situ studies enable us to identify the different steps of the structural evolution during deposition with a set of parameters as well as to evaluate the effect of changing parameters on the structural characteristics of the deposited film. Besides the in-situ studies, other complementary ex-situ characterization techniques such as XRD at a laboratory source, Rutherford backscattering spectroscopy(RBS), Auger electron spectroscopy (AES), cross-sectional transmission electron microscopy (X-TEM), scanning electron microscopy (SEM), and electrical resistivity (ER) measurements during temperature cycling have been used for a fine structural characterization. In this study, mainly naturally and thermally oxidized Si(100) substrates, TiN buffer layers with different thicknesses (i.e. the TiN topmost layer crystallographic orientation is thickness dependent) and MgO(100) single crystals were used as substrates. The chosen experimental procedure led to a controlled composition and preferential orientation of the films. The type of substrate plays an important role for the texture of the sputtered Ni-Ti films and according to the ER results, the distinct crystallographic orientations of the Ni-Ti films influence their phase transformation characteristics.

Anti-Corrosion performance of a new silane coating for corrosion protection of AZ31 Magnesium alloy in Hank’s solution

Mg alloys can be used as bioresorsable metallic implants. However, the high corrosion rate of magnesium alloys has limited their biomedical applications. Although Mg ions are essential to the human body, an excess may cause undesirable health effects. Therefore, surface treatments are required to enhance the corrosion resistance of magnesium parts, decreasing its rate to biocompatible levels and allowing its safe application as bioresorbable metallic implants. The application of biocompatible silane coatings is envisaged as a suitable strategy for retarding the corrosion process of magnesium alloys. In the current work, a new glycidoxypropyltrimethoxysilane (GPTMS) based coating was tested on AZ31 magnesium substrates subjected to different surface conditioning procedures before coating deposition. The surface conditioning included a short etching with hydrofluoric acid (HF) or a dc polarisation in alkaline electrolyte. The silane coated samples were immersed in Hank's solution and the protective performance of the coating was studied through electrochemical impedance spectroscopy (EIS). The EIS data was treated by new equivalent circuit models and the results revealed that the surface conditioning process plays a key role in the effectiveness of the silane coating. The HF treated samples led to the highest impedance values and delayed the coating degradation, compared to the mechanically polished samples or to those submitted to dc polarisation.