Low temperature sulfurization of electrodeposited Cu(In,Al)Se-2 thin films

Sulfurization of Cu(In,Al)Se-2 films is carried out in an indigenously made set up at moderately low temperature. The films are sulfurized for different time durations of 15, 30, 45 and 60 min at 150 degrees C. InSe and Cu2S phases occurred in the films during the initial stage of sulfurization along with Cu(In,Al)(Se,S)(2) phase. The compositional analysis shows that the sulfur incorporation is saturated after 30 min. Crystallinity increased with the increase in sulfurization time. The band gap of the Cu(In,Al)Se-2 film increased up to 1.35 eV with the addition of sulfur. Single phase Cu(In,Al)(Se,S)(2) with high crystallinity is obtained after 60 min of sulfurization. (C) 2014 Elsevier B.V. All rights reserved.

ADI方法求解Navier-Stokes方程的一个改进格式

ADI方法常被用来计算不可压缩Navier-Stokes方程。在处理涡度方程的非线性项和涡度在壁面上的条件时,通常采用滞后的方法对涡度方程和流函数方程分别求解。然而,非线性项的滞后破坏了ADI方法的完全二阶精度;涡度方程和流函数方程分别求解减弱了两个方程的耦合性;涡度壁面条件的滞后则破坏了方法的完全隐式。本文在应用ADI方法求解涡度方程和流函数方程时应用了一种交替线性化的技术,对涡度方程和流函数方程耦合求解,内点和边界点上的涡度和流函数值同时求出。因此,ADI方法保持了完全的二阶精度,避免了上面所提到的问题。作者应用这一方法计算了雷诺数R_θ等于1,10,100,500,1000时的二维方腔流动(空间步长h=1/20)。计算结果表明:这一方法保持了通常ADI方法的优点,可以应用大的时间步长。最后补充计算了雷诺数R_θ=2000的二维方腔流动。

Mixed-mode fracture mechanisms near the fatigue threshold of aisi-316 stainless-steel

Near threshold, mixed mode (I and II), fatigue crack growth occurs mainly by two mechanisms, coplanar (or shear) mode and branch (or tensile) mode. For a constant ratio of ΔK_I/ΔK_II the shear mode growth shows a self-arrest character and it would only start again when ΔK_I and ΔK_II are increased. Both shear crack growth and the early stages of tensile crack growth, are of a crystallographic nature; the fatigue crack proceeds along slip planes or grain boundaries. The appearance of the fracture surfaces suggest that the mechanism of crack extension is by developing slip band microcracks which join up to form a macrocrack. This process is thought to be assisted by the nature of the plastic deformation within the reversed plastic zone where high back stresses are set up by dislocation pile-ups against grain boundaries. The interaction of the crack tip stress field with that of the dislocation pile-ups leads to the formation of slip band microcracks and subsequent crack extension. The change from shear mode to tensile mode growth probably occurs when the maximum tensile stress and the microcrack density in the maximum tensile plane direction attain critical values.

Sequence context analysis of 8.2 million single nucleotide polymorphisms in the human genome

We analyzed n-mers (n=3-8) in the local environment of 8,249,446 human SNPs and compared their distribution with that in the genome reference sequences. The results revealed that the short sequences, which contained at least one CpG dinucleotide, occurred

草鱼、中华鳖IL-2活性影响因素的研究

结果显示 :当年草鱼种和中华鳖脾细胞培养上清液中能检测出IL 2活性 ,而且 1龄以上草鱼、中华鳖的IL 2活性高于当年孵化的草鱼和中华鳖。草鱼、中华鳖脾细胞在 2 5℃培养温度条件下 ,其上清液中IL 2活性最高 ,35℃次之 ,1 5℃最低。因此 ,草鱼、中华鳖IL 2活性在一定范围内是随着年龄增加而增强和依赖温度的。通过小鼠胸腺细胞增殖和对小鼠L92 9细胞杀伤率的实验表明 37℃比 2 5℃检测温度下所测的IL 2活性高 ,而中华鳖胸腺细胞增殖实验却显示 2 5℃检测温度下IL 2活性高于 37℃

Luminescence study of (11(2)over-bar0) GaN film grown by metalorganic chemical-vapor deposition

Investigations on photoluminescence properties of (11 (2) over bar0) GaN grown on (1 (1) over bar 02) Al2O3 substrate by metalorganic chemical-vapor deposition are reported. Several emission lines not reported before are observed at low temperature. The sharp peak at 3.359 eV is attributed to the exciton bound to the neutral acceptor. Another peak at 3.310 eV represents a free-to-bound, probably a free electron-to-acceptor, transition. The 3.241 and 3.170 eV lines are interpreted as phonon replica lines of the 3.310 eV line. The phonon energy is 70 meV, consistent with the energy of transverse optical E-1 phonon. The optical properties of the lines are analyzed. (C) 2003 American Institute of Physics.

Hydrothermal synthesis and crystal structure of a novel compound: [Ni(phen)(3)](2)[(SiMo10V2O40)-O-IV((VO)-O-IV)2]center dot 2H(2)O

A novel compound [Ni(phen)(3)](2)[(SiMo10V1/2O40)-O-V((VO)-O-IV)(2)] . 2H(2)O has been hydrothermally synthesized and structurally characterized by single-crystal X-ray diffraction. The compound crystallizes in the triclinic, system, space group P-1, a = 12.378(4) Angstrom, b = 14.148(5) Angstrom, c = 14.316(2) Angstrom, alpha = 105.91(2)degrees, beta = 95.31(2)degrees, gamma = 96.89(3)degrees, V = 2373.0(12) Angstrom(3), Z = 1, (lambdaMo(Kalpha)) = 0.71073 Angstrom, R1 (wR2) = 0.0869(0.2174). Data were collected on a Siemens P4 four-circle diffractometer at 293 K in the range of 1.51 < theta < 22.50degrees using the omega-scan technique. Empirical absorption correction (psi scan) was applied. The structure was solved by the direct method and refined by the Full-matrix least-squares on F-2 using the SHELXL-97 software. X-ray crystallographic study showed that the title compound contained a bi-capped alpha-Kegin-type [(SiMo10V2O40)-O-IV((VO)-O-IV)(2)](4-) polyoxoanion.

Aspects of midwifery care 2: 'enhanced role' and social aspects

This is the second in a series of six papers presenting key findings from a national study that was undertaken to investigate the role and responsibilities of midwives and to identify and address continuing educational need. The background to the study and the titles of other papers in the series were outlined in the first paper. This paper focuses on two key aspects of the midwife’s role: ‘enhanced role’ activities and social and emotional care. The implications of the findings for practice and education are discussed.

Microstructure, mechanical properties and chemical degradation of brazed AISI 316 stainless steel/alumina systems

The main aims of the present study are simultaneously to relate the brazing parameters with: (i) the correspondent interfacial microstructure, (ii) the resultant mechanical properties and (iii) the electrochemical degradation behaviour of AISI 316 stainless steel/alumina brazed joints. Filler metals on such as Ag–26.5Cu–3Ti and Ag–34.5Cu–1.5Ti were used to produce the joints. Three different brazing temperatures (850, 900 and 950 °C), keeping a constant holding time of 20 min, were tested. The objective was to understand the influence of the brazing temperature on the final microstructure and properties of the joints. The mechanical properties of the metal/ceramic (M/C) joints were assessed from bond strength tests carried out using a shear solicitation loading scheme. The fracture surfaces were studied both morphologically and structurally using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction analysis (XRD). The degradation behaviour of the M/C joints was assessed by means of electrochemical techniques. It was found that using a Ag–26.5Cu–3Ti brazing alloy and a brazing temperature of 850 °C, produces the best results in terms of bond strength, 234 ± 18 MPa. The mechanical properties obtained could be explained on the basis of the different compounds identified on the fracture surfaces by XRD. On the other hand, the use of the Ag–34.5Cu–1.5Ti brazing alloy and a brazing temperature of 850 °C produces the best results in terms of corrosion rates (lower corrosion current density), 0.76 ± 0.21 μA cm−2. Nevertheless, the joints produced at 850 °C using a Ag–26.5Cu–3Ti brazing alloy present the best compromise between mechanical properties and degradation behaviour, 234 ± 18 MPa and 1.26 ± 0.58 μA cm−2, respectively. The role of Ti diffusion is fundamental in terms of the final value achieved for the M/C bond strength. On the contrary, the Ag and Cu distribution along the brazed interface seem to play the most relevant role in the metal/ceramic joints electrochemical performance.

Metas de logro 2 x 2 en estudiantes españoles de Educación Física.

Resumen tomado de la publicación. Contiene anexo con 'Escala de Metas de Logro 2 x 2 en Educación Física'