High-velocity oxyfuel Cr3C2-NiCr replacing hard chromium coatings

Comparative wear and corrosion properties of Cr3C2-NiCr (CC-TS) (a high-velocity oxyfuel [HVOF]) and hard chromium (HC) coating's obtained on a steel substrate have been studied. The structural characterization was done before and after measurements by optical microscopy, scanning electron microscopy, and scanning white light interferometry. Wear and corrosion properties were evaluated by ball on disk (ASTM G99-90), rubber wheel (ASTM G65-91), and electrochemical measurements of open circuit and polarization curves. The best corrosion and wear resistance was for the CC-TS obtained by HVOF. The open-circuit potential values measured for both samples after 18 h of immersion we're: -0.240 and -0.550 V, respectively, for CC-TS and HC, versus Ag/AgCl,KClsat. Three orders of magnitude lower volume loss were found for CC-TS (HVOF) after friction tests compared with HC.

WC-CoCr coatings sprayed by high velocity oxygen-fuel (HVOF) flame on AA7050 aluminum alloy: electrochemical behavior in 3.5% NaCl solution

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Variáveis fisiológicas e neuromusculares associadas com a performance aeróbia em corredores de endurance: efeitos da distância da prova

O objetivo deste estudo foi analisar a validade do consumo máximo de oxigênio (VO2max), velocidade associada ao VO2max (vVO2max), tempo de exaustão na vVO2max (Tlim), limiar anaeróbio (LAn), economia de corrida (EC) e força explosiva (FE) para predizer a performance aeróbia de corredores de endurance nas distâncias de 1.500m, 5.000m e 10.000m. Participaram deste estudo 11 corredores de endurance moderadamente treinados (28,36 ± 6,47 anos) que realizaram os seguintes testes: provas simuladas em uma pista de 400m em diferentes dias, nas distâncias de 10.000m, 5.000m e 1.500m; teste incremental máximo para determinar os índices VO2max, vVO2max, e LAn; um teste submáximo de carga constante para determinar a EC, seguido por um teste máximo também de carga constante a 100% da vVO2max para determinar o Tlim; e um teste de salto vertical para determinar a FE. de acordo com a análise de regressão múltipla, a vVO2max utilizada de forma isolada explicou 57% da variação de performance na prova de 1.500m. No entanto, quando o Tlim, a FE e a vVO2max foram analisados em conjunto, a explicação para a performance nessa prova foi de 88%. Nos 5.000m, o Tlim, a vVO2max e o LAn responderam por 88% da variação de performance (p < 0,05). Diferentemente, na prova de 10.000m, o LAn foi a única variável que apresentou capacidade de predição de performance. em conclusão, a predição da performance aeróbia de corredores moderadamente treinados por meio de variáveis fisiológicas e neuromusculares é dependente da distância da prova (1.500m, 5.000m e 10.000m)

Reajustando o limite de tolerância biológica aplicado à plumbemia no Brasil

Foram alocados aleatoriamente vinte trabalhadores expostos ocupacionalmente ao chumbo em uma indústria de acumuladores elétricos de médio porte, no interior do Estado de São Paulo, os quais apresentavam plumbemia e excreção urinária do ácido delta-aminolevulínico, nos últimos dois anos, sempre menores que 60 µg/dL e 10 mg/L, respectivamente. Os trabalhadores foram submetidos a eletroneurografia do nervo radial direito e a dosagem de plumbemia. Com estas medidas ajustou-se um modelo de regressão linear simples de primeira ordem, tendo como variável dependente a velocidade de condução e como variável independente a plumbemia. Analisando-se a regressão ajustada, infere-se que o valor preditivo negativo do limite de tolerância biológica brasileiro aplicado à plumbemia seja de apenas 0,63. O estudo sugere que o valor do referido limite de tolerância deva ser reduzido do atual valor de 60 µg/dL para 32 µg/dL, para ter um valor preditivo negativo de 0,99.

Fluid dynamics of air in a packed bed: velocity profiles and the continuum model assumption

Air flow through packed beds was analyzed experimentally under conditions ranging from those that reinforce the effect of the wall on the void fraction to those that minimize it. The packing was spherical particles, with a tube-to-particle diameter ratio (D/dp) between 3 and 60. Air flow rates were maintained between 1.3 and 4.44 m3/min, and gas velocity was measured with a Pitot tube positioned above the bed exit. Measurements were made at various radial and angular coordinate values, allowing the distribution of air flow across the bed to be described in detail. Comparison of the experimentally observed radial profiles with those derived from published equations revealed that at high D/dp ratios the measured and calculated velocity profiles behaved similarly. At low ratios, oscillations in the velocity profiles agreed with those in the voidage profiles, signifying that treating the porous medium as a continuum medium is questionable in these cases.

ZERO SOUND-VELOCITY IN PI, RHO-MESON GASES

Sharp transitions are perhaps absent in QCD, so that one looks for physical quantities which may reflect the phase change. One such quantity is the sound velocity which was shown in lattice theory to become zero at the transition point for pure glue. We show that even in a simple bag model the sound velocity goes to zero at temperature T = T(v) not-equal 0 and that the numerical value of this T(v) depends on the nature of the meson. The average thermal energy of mesons goes linearly with T near T(v), with much smaller slope for the pion. The T(v) - s can be connected with the Boltzmann temperatures obtained from transverse momentum spectrum of these mesons in heavy-ion collision at mid-rapidity. It would be interesting to check the presence of different T(v) - s in present day finite T lattice theory.

Joint (X)over-bar and R charts with variable sample sizes and sampling intervals

Recent studies have shown that the (X) over bar chart with variable sampling intervals (VSI) and/or with variable sample sizes (VSS) detects process shifts faster than the traditional (X) over bar chart. This article extends these studies for processes that are monitored by both the (X) over bar and R charts. A Markov chain model is used to determine the properties of the joint (X) over bar and R charts with variable sample sizes and sampling intervals (VSSI). The VSSI scheme improves the joint (X) over bar and R control chart performance in terms of the speed with which shifts in the process mean and/or variance are detected.

Variable influence of ferric and cupric ions on Saccharomyces cerevisiae strains used in asymmetric organic synthesis.

Fe (III) and Cu (II) each at 50 mu M in four commercial strains of Saccharomyces cerevisiae induced an increase of NAD(P)(+) reduction in one strain (Turkish), but two others (Chilean and Brazilian), the presence of Fe(III) and/or Cu(II) diminished NAD(P)(+) reduction presumably due to free radicals formation inside these living cells. Suprisingly, in the American strain, Fe(III) induced a decrease and Cu (II) an increase of NAD(P)(+) reduction.

Microhabitat and plant structure of Characeae (Chlorophyta) populations in streams from São Paulo State, southeastern Brazil

Microhabitat distribution was investigated in five populations of Characeae (two of Chara guairensis, two of Nitella subglomerata and one of Nitella sp.) to determine the distributional patterns, the morphometric and reproductive adaptations to varying environmental conditions and niche width on a scale of few centimeters. Variations in physical variables revealed some general trends of microhabitat distribution for the Characeae populations studied, with occurrence under the following conditions: slow and narrow current velocities; substrata predominantly composed of small particle size (sand-clay); variable and generally low depths. In terms of morphological adaptations, we found some general patterns: plants with longer whorl branchlets also had longer internodes in all populations studied, whereas longer plants had also thicker axis. The former were generally associated with higher biomass (percent cover). Few correlations of morphological characters were observed with environmental variables (e.g. plant length with irradiance: negative in two populations and positive in one population). Despite the general patterns of occurrence mentioned above, our results also indicated that each population differed in its responses to environmental variables and had particular morphological and reproductive adaptations. The Characean populations occurred under a narrower range of microhabitat conditions than other macroalgae from lotic habitats, particularly lower current velocity (6.7-9.8 cm s(-1)) and a more specific substratum type (sand-clay). Niche width values (0.60-0.99) of the Characeae populations studied indicate a high degree of habitat specialization and are among the highest yet found in lotic macroalgae. The relatively narrow variations in microhabitat conditions and high niche widths here reported for Characean populations, suggest a lower tolerance to variations in current velocity, depth, irradiance and substratum type. These characteristics probably explain the relatively restricted distribution of Characeae species in streams of S (a) over tildeo Paulo State with low frequency of records in most regions.

Relationships and significance of lactate minimum, critical velocity, heart rate deflection and 3 000 m track-tests for running

The running velocities associated to lactate minimum (V-lm), heart rate deflection (V-HRd), critical velocity (CV), 3000 M (V-3000) and 10000 m performance (V-10km) were compared. Additionally the ability of V-lm and VHRd on identifying sustainable velocities was investigated.Methods. Twenty runners (28.5 +/- 5.9 y) performed 1) 3000 m running test for V3000; 2) an all-out 500 in sprint followed by 6x800 m incremental bouts with blood lactate ([lac]) measurements for V-lm; 3) a continuous velocity-incremented test with heart rate measurements at each 200 m for V-HRd; 4) participants attempted to 30 min of endurance test both at V-lm(ETVlm) and V-HRd(ETVHRd). Additionally, the distance-time and velocity-1/time relationships produced CV by 2 (500 m and 3000 m) or 3 predictive trials (500 m, 3000 m and distance reached before exhaustion during ETVHRd), and a 10 km race was recorded for V-10km.Results. The CV identified by different methods did not differ to each other. The results (m(.)min(-1)) revealed that V-.(lm) (281 +/- 14.8)< CV (292.1 +/- 17.5)=V-10km (291.7 +/- 19.3)< V-HRd (300.8 +/- 18.7)=V-3000 (304 +/- 17.5) with high correlation among parameters (P < 0.001). During ETVlm participants completed 30 min of running while on the ETVHRd they lasted only 12.5 +/- 8.2 min with increasing [lac].Conclusion. We evidenced that CV and Vim track-protocols are valid for running evaluation and performance prediction and the parameters studied have different significance. The V-lm reflects the moderate-high intensity domain (below CV), can be sustained without [lac] accumulation and may be used for long-term exercise while the V-HRd overestimates a running intensity that can be sustained for long-time. Additionally, V-3000 and V-HRd reflect the severe intensity domain (above CV).

AATS for the (X)over-bar chart with variable parameters

A Fortran computer program is given for the computation of the adjusted average time to signal, or AATS, for adaptive (X) over bar charts with one, two, or all three design parameters variable: the sample size, n, the sampling interval, h, and the factor k used in determining the width of the action limits. The program calculates the threshold limit to switch the adaptive design parameters and also provides the in-control average time to signal, or ATS.

DISTRIBUTION AND SEASONAL DYNAMICS OF RHODOPHYTA IN THE PRETO RIVER BASIN, SOUTHEASTERN BRAZIL

Distribution and seasonal dynamics of freshwater Rhodophyta were investigated in the Preto River basin, located in northwestern São Paulo State, southeastern Brazil. Twenty-two sites were sampled, six monthly during one year, four bimonthly during two years, and 12 twice (hot-rainy and cool-dry seasons) during the study period (May 1989 through March 1991). Red algal representatives were found in 19 sites (86.4%). Four species occurred in the basin with varying frequencies: Batrachospermum delicatulum (54.5%), Compsopogon coeruleus (36.4%), B. bicudoi (13.6%) and B. virgatum (4.5%). In addition, 'Chantransia' stage of the batrachospermalean species was found in 17 sites (77.3%). B. bicudoi, B. virgatum and C. coeruleus occurred only in large stream segments (greater-than-or-equal-to 3-order), generally in the main river, whereas B. delicatulum was more frequent in small streams (less-than-or-equal-to 3-order). The stream variables most closely related to the species distribution in the basin were specific conductance, pH and oxygen. B. bicudoi and B. delicatulum showed a marked seasonality: gametophytes were observed from late fall to early spring, while the 'Chantransia' stage generally occurred throughout the year. C. coeruleus was observed throughout the year in most sites, but the populations were generally more abundant from late fall to early spring. The combination of lower temperature and reduced turbidity resulting in increased illumination to the benthic algae during the dry winter months promotes the gametophytic growth of the batrachospermalean species, whereas current velocity was found to be the most influential stream variable for C. coeruleus. The persistance of the 'Chantransia' stage throughout the year as well as its tolerance to wider environmental conditions are key factors in the efficiency of the batrachospermalean life history strategy in lotic ecosystems.

A multi-cell variable frequency interleaved ZCS boost rectifier digitally controlled by FPGA

This paper presents a multi-cell single-phase high power factor boost rectifier in interleave connection, operating in critical conduction mode, employing a soft-switching technique, and controlled by Field Programmable Gate Array (FPGA). The soft-switching technique is based on zero-current-switching (ZCS) cells, providing ZC (zero-current) turn-on and ZCZV (zero-current-zero-voltage) turn-off for the active switches, and ZV (zero-vohage) turn-on and ZC (zero-current) turn-off for the boost diodes. The disadvantages related to reverse recovery effects of boost diodes operated in continuous conduction mode (additional losses, and electromagnetic interference (EMI) problems) are minimized, due to the operation in critical conduction mode. In addition, due to the interleaving technique, the rectifier's features include the reduction in the input current ripple, the reduction in the output voltage ripple, the use of low stress devices, low volume for the EMI input filter, high input power factor (PF), and low total harmonic distortion (THD) in the input current, in compliance with the IEC61000-3-2 standards. The digital controller has been developed using a hardware description language (VHDL) and implemented using a XC2S200E-SpartanII-E/Xilinx FPGA device, performing a true critical conduction operation mode for all interleaved cells, and a closed-loop to provide the output voltage regulation, like as a preregulator rectifier. Experimental results are presented for a implemented prototype with two and with four interleaved cells, 400V nominal output voltage and 220V(rms) nominal input voltage, in order to verify the feasibility and performance of the proposed digital control through the use of a FPGA device.

A phase-shifting control for variable frequency multi-cells interleaved boost pre-regulator based on FPGA device

In this paper were investigated phase-shift control strategies applied to a four cells interleaved high input-power-factor pre-regulator boost rectifier, operating in critical conduction mode, using a non-dissipative commutation cells and frequency modulation. The digital control has been developed using a hardware description language (VHDL) and implemented using the XC2S200E-SpartanII-E/Xilinx FPGA, performing a true critical conduction operation mode for a generic number of interleaved cells. Experimental results are presented, in order to verify the feasibility and performance of the proposed digital control, through the use of a Xilinx FPGA device.