Studies on design, fabrication and reliability assessment of embedded passives on a high-density interconnect (HDI) organic substrate using a sequential build-up process

One of the foremost design considerations in microelectronics miniaturization is the use of embedded passives which provide practical solution. In a typical circuit, over 80 percent of the electronic components are passives such as resistors, inductors, and capacitors that could take up to almost 50 percent of the entire printed circuit board area. By integrating passive components within the substrate instead of being on the surface, embedded passives reduce the system real estate, eliminate the need for discrete and assembly, enhance electrical performance and reliability, and potentially reduce the overall cost. Moreover, it is lead free. Even with these advantages, embedded passive technology is at a relatively immature stage and more characterization and optimization are needed for practical applications leading to its commercialization.This paper presents an entire process from design and fabrication to electrical characterization and reliability test of embedded passives on multilayered microvia organic substrate. Two test vehicles focusing on resistors and capacitors have been designed and fabricated. Embedded capacitors in this study are made with polymer/ceramic nanocomposite (BaTiO3) material to take advantage of low processing temperature of polymers and relatively high dielectric constant of ceramics and the values of these capacitors range from 50 pF to 1.5 nF with capacitance per area of approximately 1.5 nF/cm(2). Limited high frequency measurement of these capacitors was performed. Furthermore, reliability assessments of thermal shock and temperature humidity tests based on JEDEC standards were carried out. Resistors used in this work have been of three types: 1) carbon ink based polymer thick film (PTF), 2) resistor foils with known sheet resistivities which are laminated to printed wiring board (PWB) during a sequential build-up (SBU) process and 3) thin-film resistor plating by electroless method. Realization of embedded resistors on conventional board-level high-loss epoxy (similar to 0.015 at 1 GHz) and proposed low-loss BCB dielectric (similar to 0.0008 at > 40 GHz) has been explored in this study. Ni-P and Ni-W-P alloys were plated using conventional electroless plating, and NiCr and NiCrAlSi foils were used for the foil transfer process. For the first time, Benzocyclobutene (BCB) has been proposed as a board level dielectric for advanced System-on-Package (SOP) module primarily due to its attractive low-loss (for RF application) and thin film (for high density wiring) properties.Although embedded passives are more reliable by eliminating solder joint interconnects, they also introduce other concerns such as cracks, delamination and component instability. More layers may be needed to accommodate the embedded passives, and various materials within the substrate may cause significant thermo -mechanical stress due to coefficient of thermal expansion (CTE) mismatch. In this work, numerical models of embedded capacitors have been developed to qualitatively examine the effects of process conditions and electrical performance due to thermo-mechanical deformations.Also, a prototype working product with the board level design including features of embedded resistors and capacitors are underway. Preliminary results of these are presented.

Deformation and failure of a film/substrate system subjected to spherical indentation: Part 1. Experimental validation of stresses and strains derived using Hankel transform technique in an elastic film/substrate system

Our concern here is to rationalize experimental observations of failure modes brought about by indentation of hard thin ceramic films deposited on metallic substrates. By undertaking this exercise, we would like to evolve an analytical framework that can be used for designs of coatings. In Part I of the paper we develop an algorithm and test it for a model system. Using this analytical framework we address the issue of failure of columnar TiN films in Part II [J. Mater. Res. 21, 783 (2006)] of the paper. In this part, we used a previously derived Hankel transform procedure to derive stress and strain in a birefringent polymer film glued to a strong substrate and subjected to spherical indentation. We measure surface radial strains using strain gauges and bulk film stresses using photo elastic technique (stress freezing). For a boundary condition based on Hertzian traction with no film interface constraint and assuming the substrate constraint to be a function of the imposed strain, the theory describes the stress distributions well. The variation in peak stresses also demonstrates the usefulness of depositing even a soft film to protect an underlying substrate.

Turvemaan männyn (Pinus sylvestris L.) ja kuusen (Picea abies [L.] Karst.) kanto- ja juuripuun ominaisuudet ja asetoniliukoisten uuteaineiden määrä

Tutkimus on osa Metsäklusteri Oy:n Future Biorefinery –tutkimusohjelmaa, jossa kartoitetaan mahdollisuuksia hyödyntää metsäteollisuuden raaka-aineita aiempaa tarkemmin ja uusissa tuotteissa. Tutkimuksen tavoitteena on selvittää männyn (Pinus sylvestris L.) ja kuusen (Picea abies [L.] Karst.) juurten ja kantopuun rakenne ja ominaisuudet. Tutkimuksessa selvitetään löytyykö männyn ja kuusen juurista reaktiopuuta ja määritetään asetoniliukoisten uuteaineiden osuus kantoja juuripuussa. Tutkimusaineistona oli viisi eri-ikäistä mäntyä ja viisi eri-ikäistä kuusta. Juuri- ja kantoaineisto kerättiin Metsäntutkimuslaitoksen toimesta Parkanon seudulta (62.017°N, 23.017°E) hakkuun jälkeen. Maanalaisista juurista otettiin näytteet kolmelta eri etäisyydeltä juurenniskaan nähden. Kummankaan lajin juurista ei löytynyt varsinaista reaktiopuuta, mutta joissakin näytteissä havaittiin lievää reaktiopuuta. Lievää reaktiopuuta löytyi enemmän männyn kuin kuusen juurista, eikä sitä löytynyt lainkaan kaikkein ohuimmista, noin 2 cm paksuisista juurenosista. Männyn kannoissa uuteaineprosentti oli korkeampi kuin kuusen. Männyn juurissa uuteaineprosentti kasvoi edettäessä kohti juuren kärkeä. Kuusella uuteaineprosentti laski aluksi, mutta lähellä juuren kärkeä taas kasvoi. Kuoren uuteainepitoisuus oli molemmilla puulajeilla korkeampi kuin puuaineen. Tutkimusaineisto oli suppea, eikä tutkimuksessa pyritty tilastolliseen yleistettävyyteen. Laajemmasta aineistosta tehdylle tutkimukselle on tarvetta, sillä turvekankailta saatavan puun tarjonta on Suomessa kasvussa, mutta juurten uuteaine- ja reaktiopuututkimuksia on tehty vain kivennäismailta kerätyistä aineistoista.

Forest governance and climate change adaptation : Case studies of four African countries

Africa is threatened by climate change. The adaptive capacity of local communities continues to be weakened by ineffective and inefficient livelihood strategies and inappropriate development interventions. One of the greatest challenges for climate change adaptation in Africa is related to the governance of natural resources used by vulnerable poor groups as assets for adaptation. Practical and good governance activities for adaptation in Africa is urgently and much needed to support adaptation actions, interventions and planning. The adaptation role of forests has not been as prominent in the international discourse and actions as their mitigation role. This study therefore focused on the forest as one of the natural resources used for adaptation. The general objective of this research was to assess the extent to which cases of current forest governance practices in four African countries Burkina Faso, The Democratic Republic of Congo (DRC), Ghana and Sudan are supportive to the adaptation of vulnerable societies and ecosystems to impacts of climate change. Qualitative and quantitative analyses from surveys, expert consultations and group discussions were used in analysing the case studies. The entire research was guided by three conceptual sets of thinking forest governance, climate change vulnerability and ecosystem services. Data for the research were collected from selected ongoing forestry activities and programmes. The study mainly dealt with forest management policies and practices that can improve the adaptation of forest ecosystems (Study I) and the adaptive capacity through the management of forest resources by vulnerable farmers (Studies II, III, IV and V). It was found that adaptation is not part of current forest policies, but, instead, policies contain elements of risk management practices, which are also relevant to the adaptation of forest ecosystems. These practices include, among others, the management of forest fires, forest genetic resources, non-timber resources and silvicultural practices. Better livelihood opportunities emerged as the priority for the farmers. These vulnerable farmers had different forms of forest management. They have a wide range of experience and practical knowledge relevant to ensure and achieve livelihood improvement alongside sustainable management and good governance of natural resources. The contributions of traded non-timber forest products to climate change adaptation appear limited for local communities, based on their distribution among the stakeholders in the market chain. Plantation (agro)forestry, if well implemented and managed by communities, has a high potential in reducing socio-ecological vulnerability by increasing the food production and restocking degraded forest lands. Integration of legal arrangements with continuous monitoring, evaluation and improvement may drive this activity to support short, medium and long term expectations related to adaptation processes. The study concludes that effective forest governance initiatives led by vulnerable poor groups represent one practical way to improve the adaptive capacities of socio-ecological systems against the impacts of climate change in Africa.

Artificial Bee Colony (ABC) for multi-objective design optimization of composite structures

In this paper, we present a generic method/model for multi-objective design optimization of laminated composite components, based on Vector Evaluated Artificial Bee Colony (VEABC) algorithm. VEABC is a parallel vector evaluated type, swarm intelligence multi-objective variant of the Artificial Bee Colony algorithm (ABC). In the current work a modified version of VEABC algorithm for discrete variables has been developed and implemented successfully for the multi-objective design optimization of composites. The problem is formulated with multiple objectives of minimizing weight and the total cost of the composite component to achieve a specified strength. The primary optimization variables are the number of layers, its stacking sequence (the orientation of the layers) and thickness of each layer. The classical lamination theory is utilized to determine the stresses in the component and the design is evaluated based on three failure criteria: failure mechanism based failure criteria, maximum stress failure criteria and the tsai-wu failure criteria. The optimization method is validated for a number of different loading configurations-uniaxial, biaxial and bending loads. The design optimization has been carried for both variable stacking sequences, as well fixed standard stacking schemes and a comparative study of the different design configurations evolved has been presented. Finally the performance is evaluated in comparison with other nature inspired techniques which includes Particle Swarm Optimization (PSO), Artificial Immune System (AIS) and Genetic Algorithm (GA). The performance of ABC is at par with that of PSO, AIS and GA for all the loading configurations. (C) 2009 Elsevier B.V. All rights reserved.

Puunoston kehittäminen Stora Enso Metsän Helsingin palvelupisteessä

The operation environment in the roundwood trade in Finland in the 1990’s include several changes. They are changes in the structure of non-industrial private forest (NIPF) ownership, forest taxation, in forest legislation, in price recommendation agreement, diminishing resources of forestry extension services, etc. At the same time, the roundwood demand has been rising. All these developments cause uncertainty in wood procurement organisations, and call for research to find out how to adapt into the changing environment. The objective of this study is to produce information for roundwood purchasing planning and cus-tomer satisfaction management to be used by Stora Enso Metsä Customer Service, Helsinki. For this pur-pose, data needs to be gathered about the urban NIPFs and their forest estates, behaviour related to forestry and timber-selling, customer satisfaction in their latest timber selling transaction, and their opinions about Enso’s new customer service office and its service concept. To fulfil the objective of the study, a NIPF -owner -survey (N=1064, response rate 39,7%) was con-ducted in October 1998-January 1999. The sample was made on the basis of the marketing database of Stora Enso Oyj Forest Customer Service in Helsinki. In planning the frame of reference of the empirical study, the model of service quality by Grönroos was applied. The following aspects were included in the 7-page questionnaire: demographic, sosio-economic and forest estate background, relation to the forest service supply, behaviour related to forestry, timber-selling motives and behaviour, last contact organisation and its image in forestry business, expectations and percep-tions in the latest timber-selling transactions, and behavioural intentions. The results revealed that the share of women, pensioners and academically educated people among forest owners was quite high. The majority of the forest estates of the metropolitan forest owners were situ-ated in the provinces of South Finland and East Finland. The average forest estate area was considerably smaller than in a previous study. Economic and recreational objectives were most important in the use of forests. Forest Associations were involved in half of the roundwood sales transactions of the respondents in the metropolitan area. The wood quantity of transactions was considerably higher than the average in the whole country. Bank-organised forest-related activities, taxation infos and trips to the forest were the most popular activities. Among the services, silvicultural advices were needed mostly and stub treatment least. Brochure material related to stumpage timber sales and taxation were considered most important compared to material related to delivery sales. The service expectations were at highest for women and they were less satisfied with the service than men. 2nd and 3rd generation residents of the metropolitan area thought about the new customer service concept more positively than the 1st generation residents. Internet users under 60 years thought more positively about new satellite picture-based woodlot search concept. Cross-tabulation of factor scores against background variables indicated that women with relatively low education level a greater need to sell roundwood than entrepreneurs, white-collar workers and directors, and Internet users. Suspiciousness towards timber procurement organisations was relatively strong among women and those whose forest income share of the total income was either null or over 20 %. The average customer satisfaction score was negative in all nine questions. Statistical differences be-tween different companies did not exist in the average satisfaction scores. Stora Enso’s Helsinki forest cus-tomer service could choose the ability to purchase all timber grades as its competitive advantage. Out of nine service dimension included in the questionnaire, in this particular service dimension, Enso’s Helsinki forest customer service’s score exceeded most all organisations’ average customer satisfaction score. On the basis of importance – performance matrix, advice and quidance could have been provided more to the forest owners in their latest timber–selling transaction.

Modelling of symmetric laminates under extension

A higher-order theory of laminated composites under in-plane loads is developed. The displacement field is expanded in terms of the thickness co-ordinate, satisfying the zero shear stress condition at the surfaces of the laminate. Using the principle of virtual displacement, the governing equations and boundary conditions are established. Numerical results for interlaminar stresses arising in the case of symmetric laminates under uniform extension have been obtained and are compared with similar results available in the literature.

Factors affecting partitioning of private forest holdings in Finland.

Questions of the small size of non-industrial private forest (NIPF) holdings in Finland are considered and factors affecting their partitioning are analyzed. This work arises out of Finnish forest policy statements in which the small average size of holdings has been seen to have a negative influence on the economics of forestry. A survey of the literature indicates that the size of holdings is an important factor determining the costs of logging and silvicultural operations, while its influence on the timber supply is slight. The empirical data are based on a sample of 314 holdings collected by interviewing forest owners in the years 1980-86. In 1990-91 the same holdings were resurveyed by means of a postal inquiry and partly by interviewing forest owners. The principal objective in compiling the data is to assist in quantifying ownership factors that influence partitioning among different kinds of NIPF holdings. Thus the mechanism of partitioning were described and a maximum likelihood logistic regression model was constructed using seven independent holding and ownership variables. One out of four holdings had undergone partitioning in conjunction with a change in ownership, one fifth among family owned holdings and nearly a half among jointly owned holdings. The results of the logistic regression model indicate, for instance, that the odds on partitioning is about three times greater for jointly owned holdings than for family owned ones. Also, the probabilities of partitioning were estimated and the impact of independent dichotomous variables on the probability of partitioning ranged between 0.02 and 0.10. The low value of the Hosmer-Lemeshow test statistic indicates a good fit of the model and the rate of correct classification was estimated to be 88 per cent with a cutoff point of 0.5. The average size of holdings undergoing ownership changes decreased from 29.9 ha to 28.7 ha over the approximate interval 1983-90. In addition, the transition probability matrix showed that the trends towards smaller size categories mostly involved in the small size categories, less than 20 ha. The results of the study can be used in considering the effects of the small size of holdings for forestry and if the purpose is to influence partitioning through forest or rural policy.

Analysis of edge delaminations in laminates through combined use of quasi-three-dimensional, eight-noded, two-noded and transition elements

The use of appropriate finite elements in different regions of a stressed solid can be expected to be economical in computing its stress response. This concept is exploited here in studying stresses near free edges in laminated coupons. The well known free edge problem of [0/90], symmetric laminate is considered to illustrate the application of the concept. The laminate is modelled as a combination of three distinct regions. Quasi-three-dimensional eight-noded quadrilateral isoparametric elements (Q3D8) are used at and near the free edge of the laminate and two-noded line elements (Q3D2) are used in the region away from the free edge. A transition element (Q3DT) provides a smooth inter-phase zone between the two regions. Significant reduction in the problem size and hence in the computational time and cost have been achieved at almost no loss of accuracy.

Curved composite beams—optimum lay-up for buckling by ranking

Instability of laminated curved composite beams made of repeated sublaminate construction is studied using finite element method. In repeated sublaminate construction, a full laminate is obtained by repeating a basic sublaminate which has a smaller number of plies. This paper deals with the determination of optimum lay-up for buckling by ranking of such composite curved beams (which may be solid or sandwich). For this purpose, use is made of a two-noded, 16 degress of freedom curved composite beam finite element. The displacements u, v, w of the element reference axis are expressed in terms of one-dimensional first-order Hermite interpolation polynomials, and line member assumptions are invoked in formulation of the elastic stiffness matrix and geometric stiffness matrix. The nonlinear expressions for the strains, occurring in beams subjected to axial, flexural and torsional loads, are incorporated in a general instability analysis. The computer program developed has been used, after extensive checking for correctness, to obtain optimum orientation scheme of the plies in the sublaminate so as to achieve maximum buckling load for typical curved solid/sandwich composite beams.

Optimum Design of Composite Laminates for Strength by Ranking

In this paper we describe a method for the optimum design of fiber rein forced composite laminates for strength by ranking. The software developed based on this method is capable of designing laminates for strength; which are subjected to inplane and/or bending loads and optionally hygrothermal loads. Symmetric laminates only are considered which are assumed to be made of repeated sublaminate construction. Various layup schemes are evaluated based on the laminated plate theory and quadratic failure cri terion for the given mechanical and hygrothermal loads. The optimum layup sequence in the sublaminate and the number of such sublaminates required are obtained. Further, a ply-drop round-off scheme is adopted to arrive at an optimum laminate thickness. As an example, a family of 0/90/45/ -45 bi-directional lamination schemes are examined for dif ferent types of loads and the gains in optimising the ply orientations in a sublaminate are demonstrated.

Alikasvoksen mittaus ja kartoitus laserkeilauksella

Tasaikäisen metsän alle muodostuvilla alikasvoksilla on merkitystä puunkorjuun, metsänuudistamisen, näkemä-ja maisema-analyysien sekä biodiversiteetin ja hiilitaseen arvioinnin kannalta. Ilma-aluksista tehtävä laserkeilaus on osoittautunut tehokkaaksi kaukokartoitusmenetelmäksi varttuneiden puustojen mittauksessa. Laserkeilauksen käyttöönotto operatiivisessa metsäsuunnittelussa mahdollistaa aiempaa tarkemman tiedon tuottamisen alikasvoksista, mikäli alikasvoksen ominaisuuksia voidaan tulkita laseraineistoista. Tässä työssä käytettiin tarkasti mitattuja maastokoealoja ja kaikulaserkeilausaineistoja (discrete return LiDAR) usealta vuodelta (1–2 km lentokorkeus, 0,9–9,7 pulssia m-2). Laserkeilausaineistot oli hankittu Optech ALTM3100 ja Leica ALS50-II sensoreilla. Koealat edustavat suomalaisia tasaikäisiä männiköitä eri kehitysvaiheissa. Tutkimuskysymykset olivat: 1) Minkälainen on alikasvoksesta saatu lasersignaali yksittäisen pulssin tasolla ja mitkä tekijät signaaliin vaikuttavat? 2) Mikä on käytännön sovelluksissa hyödynnettävien aluepohjaisten laserpiirteiden selitysvoima alikasvospuuston ominaisuuksien ennustamisessa? Erityisesti haluttiin selvittää, miten laserpulssin energiahäviöt ylempiin latvuskerroksiin vaikuttavat saatuun signaaliin, ja voidaanko laserkaikujen intensiteetille tehdä energiahäviöiden korjaus. Puulajien väliset erot laserkaiun intensiteetissä olivat pieniä ja vaihtelivat keilauksesta toiseen. Intensiteetin käyttömahdollisuudet alikasvoksen puulajin tulkinnassa ovat siten hyvin rajoittuneet. Energiahäviöt ylempiin latvuskerroksiin aiheuttivat alikasvoksesta saatuun lasersignaaliin kohinaa. Energiahäviöiden korjaus tehtiin alikasvoksesta saaduille laserpulssin 2. ja 3. kaiuille. Korjauksen avulla pystyttiin pienentämään kohteen sisäistä intensiteetin hajontaa ja parantamaan kohteiden luokittelutarkkuutta alikasvoskerroksessa. Käytettäessä 2. kaikuja oikeinluokitusprosentti luokituksessa maan ja yleisimmän puulajin välillä oli ennen korjausta 49,2–54,9 % ja korjauksen jälkeen 57,3–62,0 %. Vastaavat kappa-arvot olivat 0,03–0,13 ja 0,10–0,22. Tärkein energiahäviöitä selittävä tekijä oli pulssista saatujen aikaisempien kaikujen intensiteetti, mutta hieman merkitystä oli myös pulssin leikkausgeometrialla ylemmän latvuskerroksen puiden kanssa. Myös 3. kaiuilla luokitustarkkuus parani. Puulajien välillä havaittiin eroja siinä, kuinka herkästi ne tuottavat kaiun laserpulssin osuessa puuhun. Kuusi tuotti kaiun suuremmalla todennäköisyydellä kuin lehtipuut. Erityisen selvä tämä ero oli pulsseilla, joissa oli energiahäviöitä. Laserkaikujen korkeusjakaumapiirteet voivat siten olla riippuvaisia puulajista. Sensorien välillä havaittiin selviä eroja intensiteettijakaumissa, mikä vaikeuttaa eri sensoreilla hankittujen aineistojen yhdistämistä. Myös kaiun todennäköisyydet erosivat jonkin verran sensorien välillä, mikä aiheutti pieniä eroavaisuuksia kaikujen korkeusjakaumiin. Aluepohjaisista laserpiirteistä löydettiin alikasvoksen runkolukua ja keskipituutta hyvin selittäviä piirteitä, kun rajoitettiin tarkastelu yli 1 m pituisiin puihin. Piirteiden selitysvoima oli parempi runkoluvulle kuin keskipituudelle. Selitysvoima ei merkittävästi alentunut pulssitiheyden pienentyessä, mikä on hyvä asia käytännön sovelluksia ajatellen. Lehtipuun osuutta ei pystytty selittämään. Tulosten perusteella kaikulaserkeilausta voi olla mahdollista hyödyntää esimerkiksi ennakkoraivaustarpeen arvioinnissa. Sen sijaan alikasvoksen tarkempi luokittelu (esim. puulajitulkinta) voi olla vaikeaa. Kaikkein pienimpiä alikasvospuita ei pystytä havaitsemaan. Lisää tutkimuksia tarvitaan tulosten yleistämiseksi erilaisiin metsiköihin.

Metsän erirakenteisuutta edistävien hakkuiden kannattavuustarkastelu metsäaluetasolla

Tutkimuksessa vertailtiin metsän erirakenteisuutta edistävien poimintahakkuiden ja pienaukkohakkuiden kannattavuutta metsänhoitosuositusten mukaiseen metsänkasvatukseen Keski-Suomessa. Poimintahakkuut ja pienaukkohakkuut ovat menetelmiä, joilla voidaan lisätä luonnonmetsän häiriödynamiikan mukaista pienipiirteistä elinympäristöjen vaihtelua ja siksi ne sopivat etenkin erityiskohteisiin monimuotoisuuden, maiseman tai metsien monikäytön vuoksi. Ne johtavat yleensä vähitellen eri-ikäisrakenteiseen metsään, jossa puuston läpimittaluokkajakauma muistuttaa käänteistä J-kirjainta. Eri-ikäisrakenteisen metsänkäsittelyn taloudellista kannattavuutta puoltavat uudistumiskustannusten poisjäänti ja tukkipuihin painottuvat säännöllisin väliajoin toteutuvat hakkuut. Menetelmän soveltumista Suomen olosuhteisiin pidetään kuitenkin epävarmana. Tässä tutkimuksessa tarkasteltiin tasaikäisrakenteisen metsän muuttamista eri-ikäisrakenteiseksi 40 vuoden siirtymäaikana Metsähallituksen hallinnoimassa Isojäven ympäristöarvometsässä Kuhmoisissa. Tutkimusaineisto koostui 405 kuusivaltaisesta tasaikäisestä kuviosta, joiden pinta-alasta metsämaata on 636 hehtaaria. Metsän kehitystä simuloitiin puutason kasvumalleja käyttäen ja käsittelytoimenpiteet simuloitiin viisivuotiskausittain SIMO-metsäsuunnitteluohjelmistolla. Simulointien avulla selvitettiin jokaisen käsittelyskenaarion hakkuumäärät puutavaralajeittain, diskontatut kassavirrat ja puustopääoman muutos tarkasteluajanjakson aikana. Puunkorjuun yksikkökustannusten laskennan apuna käytettiin automatisoitua seurantajärjestelmää, jossa metsäkoneisiin asennettuilla matkapuhelimilla kerättiin MobiDoc2-sovelluksella metsäkoneiden käytöstä kiihtyvyystiedot, GPS-paikkatiedot ja syötetiedot. Lopulta jokaiselle käsittelyskenaariolle laskettiin metsän puuntuotannollista arvoa kuvaavalla tuottoarvon yhtälöllä nettonykyarvot, josta vähennettiin diskontatut puunkorjuun kustannukset. Tutkimuksen tulosten mukaan poimintahakkuun NPV oli 3 prosentin korkokannalla noin 91 % (7420 €/ha) ja pienaukkohakkuiden noin 99 % (8076 €/ha) metsänhoitosuositusten mukaisesta käsittelystä (8176 €/ha). Komparatiivinen statiikka osoitti, että korkokannan kasvattaminen 5 prosenttiin ei olennaisesti lisännyt nettonykyarvojen eroja. Poimintahakkuiden puunkorjuun yksikkökustannukset olivat 0,8 €/m3 harvennushakkuita pienemmät ja 7,2 €/m3 uudistushakkuita suuremmat. Pienaukkohakkuiden yksikkökustannukset olivat 0,7 €/m3 uudistushakkuita suuremmat.Tulosten perusteella on väistämätöntä että siirtymävaihe tasaikäisrakenteisesta eri-ikäisrakenteiseksi metsäksi aiheuttaa taloudellisia tappioita siitäkin huolimatta, että hakkuut ovat voimakkaita ja tehdään varttuneeseen kasvatusmetsään. Tappion määrä on metsän peitteisyyden ylläpidosta aiheutuva vaihtoehtoiskustannus.

An improved iterative finite element solution for pin joints

Accurate, reliable and economical methods of determining stress distributions are important for fastener joints. In the past the contact stress problems in these mechanically fastened joints using interference or push or clearance fit pins were solved using both inverse and iterative techniques. Inverse techniques were found to be most efficient, but at times inadequate in the presence of asymmetries. Iterative techniques based on the finite element method of analysis have wider applications, but they have the major drawbacks of being expensive and time-consuming. In this paper an improved finite element technique for iteration is presented to overcome these drawbacks. The improved iterative technique employs a frontal solver for elimination of variables not requiring iteration, by creation of a dummy element. This automatically results in a large reduction in computer time and in the size of the problem to be handled during iteration. Numerical results are compared with those available in the literature. The method is used to study an eccentrically located pin in a quasi-isotropic laminated plate under uniform tension.

Atmospheric boundary-layer across Hadley and Ferrel cells over the Indian Ocean

A Southern Ocean Pilot cruise covering the latitudes from 10 degrees N to 56 degrees S in the open Indian Ocean was carried out during January February 2004. Surface and upper air data collected during this cruise are reported here. It is shown that the broad features of the atmosphere, in particular that of temperature, follow the tropical and mid-latitude weather expected during January February in this region. However, the atmospheric boundary-layer shows large variations, both in its height and structure between tropics and high latitudes. Strong influence of the surface heat flux on boundary layer structure is clearly seen. Humidity field reveals several local maxima and minima, suggesting a laminated atmosphere with air from different sources moving almost unmixed in adjacent layers.