Lagrangian multipliers for coast-arcs of optimum space trajectories

Some properties of generalized canonical systems - special dynamical systems described by a Hamiltonian function linear in the adjoint variables - are applied in determining the solution of the two-dimensional coast-arc problem in an inverse-square gravity field. A complete closed-form solution for Lagrangian multipliers - adjoint variables - is obtained by means of such properties for elliptic, circular, parabolic and hyperbolic motions. Classic orbital elements are taken as constants of integration of this solution in the case of elliptic, parabolic and hyperbolic motions. For circular motion, a set of nonsingular orbital elements is introduced as constants of integration in order to eliminate the singularity of the solution.

Numerical and experimental investigation of thermal louvers for space applications

Thermal louvers, using movable or rotating shutters over a radiating surface, have gained a wide acceptance as highly efficient devices for controlling the temperature of a spacecraft. This paper presents a detailed analysis of the performance of a rectangular thermal louver with movable blades. The radiative capacity of the louver, determined by its effective emittance, is calculated for different values of the blades opening angle. Experimental results obtained with a prototype of a spacecraft thermal louver show good agreement with the theoretical values.

Speed Control of an Autonomous Mobile Robot: Comparison between a PID Control and a Control Using Fuzzy Logic

An Autonomous Mobile Robot battery driven, with two traction wheels and a steering wheel is being developed. This Robot central control is regulated by an IPC, which controls every function of security, steering, positioning localization and driving. Each traction wheel is operated by a DC motor with independent control system. This system is made up of a chopper, an encoder and a microcomputer. The IPC transmits the velocity values and acceleration ramp references to the PIC microcontrollers. As each traction wheel control is independent, it's possible to obtain different speed values for each wheel. This process facilities the direction and drive changes. Two different strategies for speed velocity control were implemented; one works with PID, and the other with fuzzy logic. There were no changes in circuits and feedback control, except for the PIC microcontroller software. Comparing the two different speed control strategies the results were equivalent. However, in relation to the development and implementation of these strategies, the difficulties were bigger to implement the PID control.

A Test Bed Applied Mobile Robot Navigation

It is presented a test bed applied to studies on dynamics, control, and navigation of mobile robots. A cargo ship scale model was chosen, which can be radio-controlled or operated autonomously through an embedded control system. A control program, which manages on board mission execution, is implemented on a microcontroller. Navigation is based on an electronic compass, which includes automatic compensation for pitch and roll motions. Heading control loop is based on this sensor, and on a rudder positioning system. A propulsion control system is also implemented. Typical manoeuvres as the turning test and "zig-zag", were implemented and tested. They are included on a manoeuvre library, and can be accessed independently or in combined modes. The embedded system is also in charge of signal acquisition and storing during the missions. It is possible to analyse experiments on identification of ship dynamics, control, and navigation, through the data transferred to a PC by serial communication. Navigation is going to be improved by including inertial sensors on board, and a DGPS. Preliminary tests are aimed to ship identification, and manoeuvrability, using free model tests. Future steps include extending this system for developing other mobile robots as, ROVs, AUVs, and aerial vehicles.

Experimental study applied to an industrial robot by using variable structure controllers and friction compensation

Control of an industrial robot is mainly a problem of dynamics. It includes non-linearities, uncertainties and external perturbations that should be considered in the design of control laws. In this work, two control strategies based on variable structure controllers (VSC) and a PD control algorithm are compared in relation to the tracking errors considering friction. The controller's performances are evaluated by adding an static friction model. Simulations and experimental results show it is possible to diminish tracking errors by using a model based friction compensation scheme. A SCARA robot is used to illustrate the conclusions of this paper.

The Rebirth of Dinamo Riga: From the Glorious Soviet Past to the Kontinental Hockey League

Since the end of Cold War rivalries, the world of international hockey was deemed to becoming increasingly homogenized along western sportization patterns. The introduction of the Russian-sponsored Kontinental Hockey League (KHL) signified a new era in the global diffusion of modern sports. Its recent expansion in the post-Soviet space and European countries significantly reshuffled the landscape of international hockey, offering new prospects for the studies of the intersection of sports, history, geopolitics and nationalism in the age of globalization. The aim of this study is to conceptualize the KHL and illuminate the role of ice hockey in post-Soviet Latvia. I treat the creation of the KHL and the integration of a Latvian-based team, “Dinamo Riga,” into the KHL within the broader discussion on the globalization of sports and its effects on national communities. The research is based on a case study of the modern rebirth of “Dinamo Riga” and its participation in the KHL and is confined to the scholarly themes in sports research, such as the history of modern sports and globalization, sports and nationalism. The study pays special attention to unveiling the geopolitical links between the restart of Latvian-Russian relations after the EU’s eastern enlargement and the re-emerging Latvian-Russian contacts in ice hockey. The research concludes that with the creation of the KHL, European hockey received a new charismatic “zone of prestige” for sports interaction. The project of “Dinamo Riga” became the new global phenomenon in Latvian sports in terms of its capabilities to transcend the post-Soviet geopolitical stereotypes in relation to Russia and serve as a new national symbol in the promotion and celebration of Latvian sporting nationalism. Further sociological research would require the clarification of the impact of Latvian-Russian cooperation in hockey on the bilateral relations of both countries and the formation of a national community in Latvia.

Design Space Exploration for MPSoC Architectures

Multiprocessor system-on-chip (MPSoC) designs utilize the available technology and communication architectures to meet the requirements of the upcoming applications. In MPSoC, the communication platform is both the key enabler, as well as the key differentiator for realizing efficient MPSoCs. It provides product differentiation to meet a diverse, multi-dimensional set of design constraints, including performance, power, energy, reconfigurability, scalability, cost, reliability and time-to-market. The communication resources of a single interconnection platform cannot be fully utilized by all kind of applications, such as the availability of higher communication bandwidth for computation but not data intensive applications is often unfeasible in the practical implementation. This thesis aims to perform the architecture-level design space exploration towards efficient and scalable resource utilization for MPSoC communication architecture. In order to meet the performance requirements within the design constraints, careful selection of MPSoC communication platform, resource aware partitioning and mapping of the application play important role. To enhance the utilization of communication resources, variety of techniques such as resource sharing, multicast to avoid re-transmission of identical data, and adaptive routing can be used. For implementation, these techniques should be customized according to the platform architecture. To address the resource utilization of MPSoC communication platforms, variety of architectures with different design parameters and performance levels, namely Segmented bus (SegBus), Network-on-Chip (NoC) and Three-Dimensional NoC (3D-NoC), are selected. Average packet latency and power consumption are the evaluation parameters for the proposed techniques. In conventional computing architectures, fault on a component makes the connected fault-free components inoperative. Resource sharing approach can utilize the fault-free components to retain the system performance by reducing the impact of faults. Design space exploration also guides to narrow down the selection of MPSoC architecture, which can meet the performance requirements with design constraints.

Flexible multibody dynamics and intelligent control of a hydraulically driven hybrid redundant robot machine

The assembly and maintenance of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel (VV) is highly challenging since the tasks performed by the robot involve welding, material handling, and machine cutting from inside the VV. The VV is made of stainless steel, which has poor machinability and tends to work harden very rapidly, and all the machining operations need to be carried out from inside of the ITER VV. A general industrial robot cannot be used due to its poor stiffness in the heavy duty machining process, and this will cause many problems, such as poor surface quality, tool damage, low accuracy. Therefore, one of the most suitable options should be a light weight mobile robot which is able to move around inside of the VV and perform different machining tasks by replacing different cutting tools. Reducing the mass of the robot manipulators offers many advantages: reduced material costs, reduced power consumption, the possibility of using smaller actuators, and a higher payload-to-robot weight ratio. Offsetting these advantages, the lighter weight robot is more flexible, which makes it more difficult to control. To achieve good machining surface quality, the tracking of the end effector must be accurate, and an accurate model for a more flexible robot must be constructed. This thesis studies the dynamics and control of a 10 degree-of-freedom (DOF) redundant hybrid robot (4-DOF serial mechanism and 6-DOF 6-UPS hexapod parallel mechanisms) hydraulically driven with flexible rods under the influence of machining forces. Firstly, the flexibility of the bodies is described using the floating frame of reference method (FFRF). A finite element model (FEM) provided the Craig-Bampton (CB) modes needed for the FFRF. A dynamic model of the system of six closed loop mechanisms was assembled using the constrained Lagrange equations and the Lagrange multiplier method. Subsequently, the reaction forces between the parallel and serial parts were used to study the dynamics of the serial robot. A PID control based on position predictions was implemented independently to control the hydraulic cylinders of the robot. Secondly, in machining, to achieve greater end effector trajectory tracking accuracy for surface quality, a robust control of the actuators for the flexible link has to be deduced. This thesis investigates the intelligent control of a hydraulically driven parallel robot part based on the dynamic model and two schemes of intelligent control for a hydraulically driven parallel mechanism based on the dynamic model: (1) a fuzzy-PID self-tuning controller composed of the conventional PID control and with fuzzy logic, and (2) adaptive neuro-fuzzy inference system-PID (ANFIS-PID) self-tuning of the gains of the PID controller, which are implemented independently to control each hydraulic cylinder of the parallel mechanism based on rod length predictions. The serial component of the hybrid robot can be analyzed using the equilibrium of reaction forces at the universal joint connections of the hexa-element. To achieve precise positional control of the end effector for maximum precision machining, the hydraulic cylinder should be controlled to hold the hexa-element. Thirdly, a finite element approach of multibody systems using the Special Euclidean group SE(3) framework is presented for a parallel mechanism with flexible piston rods under the influence of machining forces. The flexibility of the bodies is described using the nonlinear interpolation method with an exponential map. The equations of motion take the form of a differential algebraic equation on a Lie group, which is solved using a Lie group time integration scheme. The method relies on the local description of motions, so that it provides a singularity-free formulation, and no parameterization of the nodal variables needs to be introduced. The flexible slider constraint is formulated using a Lie group and used for modeling a flexible rod sliding inside a cylinder. The dynamic model of the system of six closed loop mechanisms was assembled using Hamilton’s principle and the Lagrange multiplier method. A linearized hydraulic control system based on rod length predictions was implemented independently to control the hydraulic cylinders. Consequently, the results of the simulations demonstrating the behavior of the robot machine are presented for each case study. In conclusion, this thesis studies the dynamic analysis of a special hybrid (serialparallel) robot for the above-mentioned special task involving the ITER and investigates different control algorithms that can significantly improve machining performance. These analyses and results provide valuable insight into the design and control of the parallel robot with flexible rods.

Energy and Dynamics of the solar agricultural robot "SolarSprayer"

The main objective of the present study was to design an agricultural robot, which work is based on the generation of the electricity by the solar panel. To achieve the proper operation of the robot according to the assumed working cycle the detailed design of the main equipment was made. By analysing the possible areas of implementation together with developments, the economic forecast was held. As a result a decision about possibility of such device working in agricultural sector was made and the probable topics of the further study were found out.

Dual light barrier method for six degrees of freedom tool center point calibration of an industrial robot

Tool center point calibration is a known problem in industrial robotics. The major focus of academic research is to enhance the accuracy and repeatability of next generation robots. However, operators of currently available robots are working within the limits of the robot´s repeatability and require calibration methods suitable for these basic applications. This study was conducted in association with Stresstech Oy, which provides solutions for manufacturing quality control. Their sensor, based on the Barkhausen noise effect, requires accurate positioning. The accuracy requirement admits a tool center point calibration problem if measurements are executed with an industrial robot. Multiple possibilities are available in the market for automatic tool center point calibration. Manufacturers provide customized calibrators to most robot types and tools. With the handmade sensors and multiple robot types that Stresstech uses, this would require great deal of labor. This thesis introduces a calibration method that is suitable for all robots which have two digital input ports free. It functions with the traditional method of using a light barrier to detect the tool in the robot coordinate system. However, this method utilizes two parallel light barriers to simultaneously measure and detect the center axis of the tool. Rotations about two axes are defined with the center axis. The last rotation about the Z-axis is calculated for tools that have different width of X- and Y-axes. The results indicate that this method is suitable for calibrating the geometric tool center point of a Barkhausen noise sensor. In the repeatability tests, a standard deviation inside robot repeatability was acquired. The Barkhausen noise signal was also evaluated after recalibration and the results indicate correct calibration. However, future studies should be conducted using a more accurate manipulator, since the method employs the robot itself as a measuring device.

The European Union and Assembling Biofuel Development – topological investigations concerning the associations between law, policy and space

Biofuels for transport are a renewable source of energy that were once heralded as a solution to multiple problems associated with poor urban air quality, the overproduction of agricultural commodities, the energy security of the European Union (EU) and climate change. It was only after the Union had implemented an incentivizing framework of legal and political instruments for the production, trade and consumption of biofuels that the problems of weakening food security, environmental degradation and increasing greenhouse gases through land-use changes began to unfold. In other words, the difference between political aims for why biofuels are promoted and their consequences has grown – which is also recognized by the EU policy-makers. Therefore, the global networks of producing, trading and consuming biofuels may face a complete restructure if the European Commission accomplishes its pursuit to sideline crop-based biofuels after 2020. My aim with this dissertation is not only to trace the manifold evolutions of the instruments used by the Union to govern biofuels but also to reveal how this evolution has influenced the dynamics of biofuel development. Therefore, I study the ways the EU’s legal and political instruments of steering biofuels are coconstitutive with the globalized spaces of biofuel development. My analytical strategy can be outlined through three concepts. I use the term ‘assemblage’ to approach the operations of the loose entity of actors and non-human elements that are the constituents of multi-scalar and -sectorial biofuel development. ‘Topology’ refers to the spatiality of this European biofuel assemblage and its parts whose evolving relations are treated as the active constituents of space, instead of simply being located in space. I apply the concept of ‘nomosphere’ to characterize the framework of policies, laws and other instruments that the EU applies and construes while attempting to govern biofuels. Even though both the materials and methods vary in the independent articles, these three concepts characterize my analytical strategy that allows me to study law, policy and space associated with each other. The results of my examinations underscore the importance of the instruments of governance of the EU constituting and stabilizing the spaces of producing and, on the other hand, how topological ruptures in biofuel development have enforced the need to reform policies. This analysis maps the vast scope of actors that are influenced by the mechanism of EU biofuel governance and, what is more, shows how they are actively engaging in the Union’s institutional policy formulation. By examining the consequences of fast biofuel development that are spatially dislocated from the established spaces of producing, trading and consuming biofuels such as indirect land use changes, I unfold the processes not tackled by the instruments of the EU. Indeed, it is these spatially dislocated processes that have pushed the Commission construing a new type of governing biofuels: transferring the instruments of climate change mitigation to land-use policies. Although efficient in mitigating these dislocated consequences, these instruments have also created peculiar ontological scaffolding for governing biofuels. According to this mode of governance, the spatiality of biofuel development appears to be already determined and the agency that could dampen the negative consequences originating from land-use practices is treated as irrelevant.

Adaptive Markov chain Monte Carlo and Bayesian filtering for state space models

This thesis is concerned with the state and parameter estimation in state space models. The estimation of states and parameters is an important task when mathematical modeling is applied to many different application areas such as the global positioning systems, target tracking, navigation, brain imaging, spread of infectious diseases, biological processes, telecommunications, audio signal processing, stochastic optimal control, machine learning, and physical systems. In Bayesian settings, the estimation of states or parameters amounts to computation of the posterior probability density function. Except for a very restricted number of models, it is impossible to compute this density function in a closed form. Hence, we need approximation methods. A state estimation problem involves estimating the states (latent variables) that are not directly observed in the output of the system. In this thesis, we use the Kalman filter, extended Kalman filter, Gauss–Hermite filters, and particle filters to estimate the states based on available measurements. Among these filters, particle filters are numerical methods for approximating the filtering distributions of non-linear non-Gaussian state space models via Monte Carlo. The performance of a particle filter heavily depends on the chosen importance distribution. For instance, inappropriate choice of the importance distribution can lead to the failure of convergence of the particle filter algorithm. In this thesis, we analyze the theoretical Lᵖ particle filter convergence with general importance distributions, where p ≥2 is an integer. A parameter estimation problem is considered with inferring the model parameters from measurements. For high-dimensional complex models, estimation of parameters can be done by Markov chain Monte Carlo (MCMC) methods. In its operation, the MCMC method requires the unnormalized posterior distribution of the parameters and a proposal distribution. In this thesis, we show how the posterior density function of the parameters of a state space model can be computed by filtering based methods, where the states are integrated out. This type of computation is then applied to estimate parameters of stochastic differential equations. Furthermore, we compute the partial derivatives of the log-posterior density function and use the hybrid Monte Carlo and scaled conjugate gradient methods to infer the parameters of stochastic differential equations. The computational efficiency of MCMC methods is highly depend on the chosen proposal distribution. A commonly used proposal distribution is Gaussian. In this kind of proposal, the covariance matrix must be well tuned. To tune it, adaptive MCMC methods can be used. In this thesis, we propose a new way of updating the covariance matrix using the variational Bayesian adaptive Kalman filter algorithm.

Amino acid composition of parturient plasma, the intervillous space of the placenta and the umbilical vein of term newborn infants

The objective of the present study was to determine the levels of amino acids in maternal plasma, placental intervillous space and fetal umbilical vein in order to identify the similarities and differences in amino acid levels in these compartments of 15 term newborns from normal pregnancies and deliveries. All amino acids, except tryptophan, were present in at least 186% higher concentrations in the intervillous space than in maternal venous blood, with the difference being statistically significant. This result contradicted the initial hypothesis of the study that the plasma amino acid levels in the placental intervillous space should be similar to those of maternal plasma. When the maternal venous compartment was compared with the umbilical vein, we observed values 103% higher on the fetal side which is compatible with currently accepted mechanisms of active amino acid transport. Amino acid levels of the placental intervillous space were similar to the values of the umbilical vein except for proline, glycine and aspartic acid, whose levels were significantly higher than fetal umbilical vein levels (average 107% higher). The elevated levels of the intervillous space are compatible with syncytiotrophoblast activity, which maintain high concentrations of free amino acids inside syncytiotrophoblast cells, permitting asymmetric efflux or active transport from the trophoblast cells to the blood in the intervillous space. The plasma amino acid levels in the umbilical vein of term newborns probably may be used as a standard of local normality for clinical studies of amino acid profiles.

Control of Robot by Means of Human Thought

Brain computer interface (BCI) is a kind of human machine interface, which provides a new interaction method between human and computer or other equipment. The most significant characteristic of BCI system is that its control input is brain electrical activities acquired from the brain instead of traditional input such as hands or eyes. BCI technique has rapidly developed during last two decades and it has mainly worked as an auxiliary technique to help the disable people improve their life qualities. With the appearance of low cost novel electrical devices such as EMOTIV, BCI technique has been applied to the general public through many useful applications including video gaming, virtual reality and virtual keyboard. The purpose of this research is to be familiar with EMOTIV EPOC system and make use of it to build an EEG based BCI system for controlling an industrial manipulator by means of human thought. To build a BCI system, an acquisition program based on EMOTIV EPOC system is designed and a MFC based dialog that works as an operation panel is presented. Furthermore, the inverse kinematics of RV-3SB industrial robot was solved. In the last part of this research, the designed BCI system with human thought input is examined and the results indicate that the system is running smoothly and displays clearly the motion type and the incremental displacement of the motion.

Plasma amino acids in pregnancy, placental intervillous space and preterm newborn infants

Plasma amino acid levels have never been studied in the placental intervillous space of preterm gestations. Our objective was to determine the possible relationship between plasma amino acids of maternal venous blood (M), of the placental intervillous space (PIVS) and of the umbilical vein (UV) of preterm newborn infants. Plasma amino acid levels were analyzed by ion-exchange chromatography in M from 14 parturients and in the PIVS and UV of their preterm newborn infants. Mean gestational age was 34 ± 2 weeks, weight = 1827 ± 510 g, and all newborns were considered adequate for gestational age. The mean Apgar score was 8 and 9 at the first and fifth minutes. Plasma amino acid values were significantly lower in M than in PIVS (166%), except for aminobutyric acid. On average, plasma amino acid levels were significantly higher in UV than in M (107%) and were closer to PIVS than to M values, except for cystine and aminobutyric acid (P < 0.05). Comparison of the mean plasma amino acid concentrations in the UV of preterm to those of term newborn infants previously studied by our group showed no significant difference, except for proline (P < 0.05), preterm > term. These data suggest that the mechanisms of active amino acid transport are centralized in the syncytiotrophoblast, with their passage to the fetus being an active bidirectional process with asymmetric efflux. PIVS could be a reserve amino acid space for the protection of the fetal compartment from inadequate maternal amino acid variations.